2019-2026 Mazda 3 4 Door When Driving -> Instrument Cluster and Display User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

When Driving -> Instrument Cluster and Display for Your Mazda 3 4 Door Fourth Generation (2019-2026)

When Driving  
Instrument Cluster and Display  
Instrument Cluster and  
Display  
Instrument Cluster  
Instrument Cluster  
▼
Instrument Cluster and Display  
▼
① Tachometer.................... page 4-19  
② Multi-information Display...............  
..................................... page 4-20  
③ Engine Coolant Temperature  
① Instrument Cluster.......... page 4-18  
② Active Driving Display..... page 4-36  
Gauge............................page 4-23  
④ Fuel Gauge..................... page 4-23  
⑤ Dashboard Illumination  
Switch............................page 4-24  
⑥ Speedometer..................page 4-18  
⑦ TRIP Switch.................... page 4-22  
Speedometer  
▼
The speedometer indicates the speed  
of the vehicle.  
4-18  
When Driving  
Instrument Cluster and Display  
Tachometer  
▼
The tachometer shows engine speed in  
thousands of revolutions per minute  
(rpm).  
CAUTION  
Do not run the engine with the  
tachometer needle in the RED ZONE.  
This may cause severe engine damage.  
*1  
1. STRIPED ZONE  
*1  
2. RED ZONE  
*
1
The range varies depending on the type of  
gauge.  
NOTE  
When the tachometer needle enters  
the STRIPED ZONE, this indicates to  
the driver that the gears should be  
shifted before entering the RED ZONE.  
4-19  
When Driving  
Instrument Cluster and Display  
Multi-information Display  
▼
1. Multi-information Display  
2. INFO switch  
The multi-information display indicates the following information.  
Speedometer  
Odometer  
Trip meter  
Outside temperature  
Distance-to-empty  
Average fuel economy  
Current fuel economy  
Deceleration Regeneration Charge Display (M Hybrid)  
i-ACTIVSENSE Display  
Compass Display  
*1  
Door-Ajar/Trunk lid-Ajar/Liftgate-Ajar Warning Indication  
Message Display  
*
1
Displayed when opening door/trunk lid/liftgate.  
4-20  
When Driving  
Instrument Cluster and Display  
The screen content changes each time the INFO switch is pressed.  
1. Basic display  
2. Drive information display  
3. i-ACTIVSENSE display  
*1  
4. Message display  
1
*
Displayed only when a warning occurs.  
The type of display for the fuel economy and the maximum driving distance can be  
changed.  
Refer to the Settings section in the Mazda Connect Owner's Manual.  
4-21  
When Driving  
Instrument Cluster and Display  
Trip meter  
Odometer, Trip Meter and Trip  
▼
Meter Selector  
The driving distance for a specified  
interval is indicated. Two types (TRIP A,  
TRIP B) of interval distance can be  
measured.  
You can switch between the odometer  
and trip meter display using the TRIP  
switch.  
For instance, trip meter A can record  
the distance from the point of origin,  
and trip meter B can record the  
distance from where the fuel tank is  
filled.  
When trip meter A is selected, TRIP A  
will be displayed. When trip meter B is  
selected, TRIP B will be displayed.  
The trip meter can be reset by pressing  
the TRIP switch for 1.5 seconds or  
more while the trip meter is displayed.  
NOTE  
Only the trip meters record tenths of  
kilometers (miles).  
1. TRIP switch  
2. Odometer display  
3. Trip meter A display  
4. Trip meter B display  
Odometer  
The odometer records the total  
distance the vehicle has been driven.  
4-22  
When Driving  
Instrument Cluster and Display  
Engine Coolant Temperature  
Gauge  
Fuel Gauge  
▼
▼
The fuel gauge shows approximately  
how much fuel is remaining in the tank  
when the ignition is switched ON. We  
recommend keeping the tank over 1/4  
full.  
Displays the engine coolant  
temperature. The blue range of the  
gauge indicates that the engine coolant  
temperature is low, and the red range  
of the gauge indicates that the engine  
coolant temperature is high and  
overheating.  
CAUTION  
When the engine coolant temperature  
gauge needle is in the red range, the  
engine coolant temperature is  
extremely high. Drive slowly to reduce  
engine load. If the engine coolant  
temperature gauge needle is in the red  
range, there is the possibility of  
overheating. Park the vehicle in a safe  
place immediately and take  
1. Full  
2. 1/4 Full  
3. Empty  
appropriate measures.  
Refer to Overheating on page 7-21.  
NOTE  
If the engine or engine coolant  
temperature is high or low, the  
engine output may be restricted to  
protect the engine.  
4-23  
When Driving  
Instrument Cluster and Display  
If the low fuel warning light illuminates  
or the fuel level is very low, refuel as  
soon as possible.  
NOTE  
(With auto-light control)  
When the ignition is switched ON in  
the early evening or at dusk, the  
dashboard illumination is dimmed  
for several seconds until the light  
sensor detects the brightness of the  
surrounding area, however, the  
dimming may cancel after the  
brightness is detected.  
If inconsistency in engine performance  
or stalling occurs due to low fuel level  
conditions, refuel the vehicle as soon  
as possible and add at least 10 L (2.7  
US gal, 2.2 Imp gal) of fuel.  
Refer to Low Fuel Warning Indication/  
Warning Light on page 7-35.  
When the lights are turned on, the  
lights-on indicator light in the  
instrument cluster turns on.  
NOTE  
After refueling, it may require some  
time for the indicator to stabilize. In  
addition, the indicator may deviate  
while driving on a slope or curve  
since the fuel moves in the tank.  
Refer to Headlights on page 4-57.  
The brightness of the instrument panel  
and dashboard illuminations can be  
adjusted by pressing the dashboard  
illumination switch while the  
The direction of the arrow (  
)
indicates that the fuel-filler lid is on  
the left side of the vehicle.  
dashboard illumination is dimmed.  
The brightness increases by pressing  
Dashboard Illumination  
▼
the + switch.  
The brightness decreases by pressing  
(Without auto-light control)  
the - switch. If you press the - switch  
while the instrument cluster is at  
maximum dimness, a sound is  
activated to notify you that the  
current dimmer setting is at  
maximum dimness.  
When the lights are turned on with the  
ignition switched ON, the brightness of  
the dashboard illumination is dimmed.  
(With auto-light control)  
When the lights are turned on with the  
ignition switched ON, the brightness of  
the dashboard illumination is dimmed.  
However, when the light sensor  
detects that the surrounding area is  
bright such as when the lights are  
turned on in the daytime, the  
dashboard illumination does not dim.  
1. Bright  
2. Dim  
4-24  
When Driving  
Instrument Cluster and Display  
Function for canceling illumination  
dimmer  
Outside Temperature Display  
▼
When the ignition is switched ON, the  
outside temperature is displayed.  
The illumination dimmer can be  
canceled by pressing the + switch  
while the instrument cluster is at  
maximum dimness and while the  
ignition is switched ON. If you press  
the + switch again while the  
illumination dimmer is canceled, a  
sound is activated to notify you that it  
is canceled. If the instrument cluster's  
visibility is reduced due to glare from  
surrounding brightness, cancel the  
illumination dimmer.  
NOTE  
NOTE  
Under the following conditions, the  
outside temperature display may  
diꢀer from the actual outside  
temperature depending on the  
surroundings and vehicle conditions:  
When the illumination dimmer is  
canceled, the instrument cluster  
cannot be dimmed even if the lights  
are turned on.  
When the illumination dimmer is  
canceled, the screen in the center  
display switches to constant display  
of the daytime screen.  
Significantly cold or hot  
temperatures.  
Sudden changes in outside  
temperature.  
The vehicle is parked.  
The vehicle is driven at low speeds.  
Changing the Temperature Unit of the  
Outside Temperature Display  
The outside temperature unit can be  
switched between Celsius and  
Fahrenheit.  
Settings can be changed by operating  
the center display screen.  
Refer to the Settings section in the  
Mazda Connect Owner's Manual.  
4-25  
When Driving  
Instrument Cluster and Display  
If there is no past fuel economy  
information such as after first  
Distance-to-empty  
▼
This displays the approximate distance  
you can travel on the remaining fuel  
based on the fuel economy.  
The distance-to-empty will be  
calculated and displayed every second.  
When the remaining  
purchasing your vehicle or the  
information is deleted when the  
battery cables are disconnected, the  
actual distance-to empty/range may  
diꢀer from the amount indicated.  
distance-to-empty is 50 km (30 miles)  
or farther, the remaining  
Average Fuel Economy  
▼
This mode displays the average fuel  
economy by calculating the total  
traveled distance and the total fuel  
consumption since the vehicle was  
purchased or the past data was reset.  
The average fuel economy is calculated  
and displayed every 30 seconds.  
The average fuel economy is also  
displayed by a red arrow in the  
distance-to-empty indication  
decreases in 10 km (10 mile)  
increments, and when the remaining  
distance-to-empty is 50 km (30 miles)  
or shorter, it decreases in 1 km (1 mile)  
increments.  
instantaneous fuel economy display.  
NOTE  
Even though the distance-to-empty  
display may indicate a suꢁcient  
amount of remaining driving distance  
before refueling is required, refuel as  
soon as possible if the fuel level is  
very low or the low fuel warning light  
illuminates.  
The display will not change unless  
you add more than approximately 9  
L (2.3 US gal, 1.9 Imp gal) of fuel.  
The average fuel economy can be reset  
by pressing the INFO switch for 1.5  
seconds or more. After the data is  
cleared, the fuel consumption is  
recalculated and the - - - L/100 km  
(- - - mpg) for the 30 seconds prior to  
it being displayed is indicated.  
The distance-to-empty is the  
approximate remaining distance the  
vehicle can be driven until all the  
graduation marks in the fuel gauge  
indicating the remaining fuel supply  
disappear.  
4-26  
When Driving  
Instrument Cluster and Display  
Current Fuel Economy  
Deceleration Regeneration Charge  
▼
▼
Display (M Hybrid)  
This displays the current fuel economy  
by calculating the amount of fuel  
consumption and the distance  
traveled.  
This displays the status of the charging  
produced by deceleration  
regeneration.  
M Hybrid  
Refer to M Hybrid on page 4-53.  
i-ACTIVSENSE Display*  
▼
Displays the system status.  
Except M Hybrid  
Refer to Lane Departure Warning  
NOTE  
System (LDWS) on page 4-106.  
Refer to Blind Spot Monitoring  
(BSM) on page 4-110.  
Refer to Traꢁc Sign Recognition  
System (TSR) on page 4-115.  
Refer to Distance & Speed Alert  
Indicates the 0 position when the  
vehicle speed is about 5 km/h (3  
mph) or slower.  
The arrow on the scale indicates the  
average fuel economy.  
(DSA) on page 4-119.  
Refer to Driver Attention Alert (DAA)  
on page 4-121.  
Refer to Driver Monitoring (DM) on  
page 4-122.  
Refer to Front Cross Traꢁc Alert  
(FCTA) on page 4-123.  
Refer to Mazda Radar Cruise Control  
(MRCC) on page 4-132.  
4-27  
*Some models.  
When Driving  
Instrument Cluster and Display  
Refer to Mazda Radar Cruise Control  
Message Display  
▼
with Stop & Go function (MRCC  
with Stop & Go function) on page  
4-142.  
A message such as the system  
operation status, a malfunction, or an  
abnormality is indicated.  
Refer to Traꢁc Jam Assist (TJA) on  
page 4-154.  
Refer to Lane-keep Assist System  
(LAS) on page 4-167.  
Refer to Smart Brake Support (SBS)  
on page 4-168.  
Refer to Cruise Control on page  
4-225.  
Warning/indicator light in instrument  
cluster turns on/flashes or symbol is  
indicated on display at same time as  
message  
Check the information regarding the  
warning/indicator light or indicated  
symbol.  
Compass Display  
Refer to If a Warning Indication/  
Warning Lights on page 4-29.  
Refer to If a Indication/Indicator Lights  
on page 4-31.  
▼
The direction the vehicle is moving is  
displayed in one of eight directions  
while the vehicle is being driven.  
Message only is indicated on display  
Follow the instructions indicated on  
the display. For the display content,  
refer to the next page.  
Refer to If a Message Indicated on  
Multi-information Display on page  
7-40.  
Warning/Indicator Lights  
▼
Instrument Cluster varies depending  
on model and specifications.  
Display  
N
Direction  
North  
S
South  
E
East  
W
West  
NE  
NW  
SE  
Northeast  
Northwest  
Southeast  
Southwest  
SW  
1. Instrument Cluster  
2. Front Center of Headliner  
Warning lights will appear in any of the  
highlighted areas  
4-28  
When Driving  
Instrument Cluster and Display  
Warning Indication/Warning Lights  
▼
These lights turn on or flash to notify the user of the system operation status or a  
system malfunction.  
Signal  
Warning  
Refer to  
*1  
7-27  
Brake System Warning Indication/Warning Light  
Electronic  
Brake Force  
Distribution  
System Warn-  
ing  
*1  
ABS Warning Indication/Warning Light  
7-28  
ABS warning  
7-30  
*1  
7-28  
7-28  
7-29  
7-29  
7-30  
Charging System Warning Indication/Warning Light  
*1  
Engine Oil Warning Indication/Warning Light  
High Engine Coolant Temperature Warning Indication  
Power Steering Malfunction Indication/Indicator Light  
Master Warning Indication  
*1  
*1  
7-30  
7-31  
7-31  
Brake Control System Warning Indication/Warning Light  
Brake Override Warning Indication  
*1  
Check Engine Indication/Light  
*
*1  
7-31  
7-31  
i-stop Warning Indication/Warning Light  
(Amber)  
*
*1  
Automatic Transmission Warning Indication/Warning Light  
4-29  
*Some models.  
When Driving  
Instrument Cluster and Display  
Signal  
Warning  
Refer to  
*
*1  
7-32  
AWD Warning Indication/Warning Light  
Air Bag/Seat Belt Pretensioner System Warning Indication/Warning  
7-33  
*1  
Light  
Flashing  
7-33  
Tire Pressure Monitoring System (TPMS) Warning Indication/Warning  
*1  
Light  
Turns on  
7-37  
*1  
7-34  
7-35  
KEY Warning Indication/Warning Light  
(Red)  
*
High Beam Control System (HBC) Warning Indication/Warning  
*1  
Light  
(Amber)  
*1  
7-35  
7-35  
7-35  
7-36  
7-36  
7-36  
i-ACTIVSENSE Warning Indication/Warning Light  
*1  
Exterior Light Warning Indication/Warning Light  
Low Fuel Warning Indication/Warning Light  
*1  
Check Fuel Cap Warning Indication/Warning Light  
*1  
Engine Oil Level Warning Indication/Warning Light  
Seat Belt Warning Indication/Warning Light (Front seat)  
Seat Belt Warning Light (Rear seat)  
7-37  
(Red)  
*
7-37  
7-37  
Low Washer Fluid Level Warning Indication/Warning Light  
Door-Ajar Warning Indication  
4-30  
*Some models.  
When Driving  
Instrument Cluster and Display  
Signal  
Warning  
Trunk lid-Ajar Warning Indication  
Refer to  
*
7-37  
*
7-37  
7-37  
Liftgate-Ajar Warning Indication  
Door-Ajar Warning Light  
*
1
The light turns on when the ignition is switched on for an operation check, and turns oꢀ a few  
seconds later or when the engine is started. If the light does not turn on or remains turned on, have  
the vehicle inspected at an Authorized Mazda Dealer.  
Indication/Indicator Lights  
▼
These lights turn on or flash to notify the user of the system operation status or a  
system malfunction.  
Signal  
Indicator  
Refer to  
Seat Belt Indicator Light (Rear seat)  
2-26  
(Green)  
*
2-70  
Front Passenger Air Bag Deactivation Indicator Light  
Immobilizer  
System  
3-43  
Theft-Deterrent  
System  
Security Indicator Light  
3-44  
Malfunction  
7-34  
KEY Indicator Light  
4-5  
(Green)  
(Green)  
*
4-16  
4-35  
i-stop Indicator Light  
*1  
Wrench Indication/Indicator Light  
4-31  
*Some models.  
When Driving  
Instrument Cluster and Display  
Signal  
Indicator  
Refer to  
*
4-44  
Shift Position Indication  
Lights-On Indicator Light  
4-57  
Headlight  
High-Low  
Beam  
4-60  
Headlight High-Beam Indicator Light  
Flashing the  
Headlights  
4-60  
Turn and  
Lane-Change  
Signals  
4-63  
Turn Signal/Hazard Warning Indicator Lights  
Hazard Warn-  
ing Flasher  
4-71  
*1*2  
7-30  
Electric Parking Brake (EPB) Indication/Indicator Light  
*1  
4-84  
4-149  
4-163  
AUTOHOLD Active Indicator Light  
*
Mazda Radar Cruise Control with Stop & Go function (MRCC with  
Stop & Go function) indicator Light  
*
Traꢁc Jam Assist (TJA) indicator Light  
Traction Con-  
trol System  
(TCS)  
4-89  
Dynamic Sta-  
bility Control  
(DSC)  
*1  
TCS/DSC Indication/Indicator Light  
4-90  
Turns on  
7-33  
*1  
4-91  
DSC OFF Indicator Light  
4-32  
*Some models.  
When Driving  
Instrument Cluster and Display  
Signal  
Indicator  
Refer to  
*
4-93  
Select Mode Indicator Light  
(White)  
(Green)  
(Amber)  
i-ACTIVSENSE Status Symbol (Warning/Risk Avoidance Support Sys-  
tem)  
4-98  
i-ACTIVSENSE OFF Symbol (Warning/Risk Avoidance Support Sys-  
tem)  
4-98  
*
4-102  
High Beam Control System (HBC) Indicator Light  
(Green)  
(White)  
*
4-134  
4-144  
Mazda Radar Cruise Control (MRCC) Standby Indication  
*
Mazda Radar Cruise Control with Stop & Go function (MRCC with  
Stop & Go function) Standby Indication  
*
4-156  
4-134  
Traꢁc Jam Assist (TJA) Standby Indication  
*
Mazda Radar Cruise Control (MRCC) Set Indication  
*
Mazda Radar Cruise Control with Stop & Go function (MRCC with  
4-144  
4-156  
Stop & Go function) Set Indication  
(Green)  
*
Traꢁc Jam Assist (TJA) Set Indication  
*
*
*1  
4-176  
4-224  
Smart Brake Support (SBS) OFF Indicator Light  
Cruise Standby Indication  
(White)  
(Green)  
*
4-224  
Cruise Set Indication  
4-33  
*Some models.  
When Driving  
Instrument Cluster and Display  
*
1 The light turns on when the ignition is switched on for an operation check, and  
turns oꢀ a few seconds later or when the engine is started. If the light does not  
turn on or remains turned on, have the vehicle inspected at an Authorized  
Mazda Dealer.  
*
2 The light turns on continuously when the parking brake is applied.  
4-34  
When Driving  
Instrument Cluster and Display  
Wrench Indication/Indicator Light  
▼
The wrench indication/indicator light  
is displayed/turns on under the  
following conditions.  
When the preset maintenance  
period has arrived.  
Refer to the Information section in  
the Mazda Connect Owner's  
Manual.  
CAUTION  
When the maintenance period  
arrives, have your vehicle inspected  
by an Authorized Mazda Dealer as  
soon as possible. If maintenance is  
neglected, a decrease in vehicle  
performance may occur which  
could cause damage. Have your  
vehicle inspected before the  
maintenance period arrives.  
If the vehicle continues to be  
driven after the engine oil  
replacement period has passed, it  
could cause damage to the engine.  
Replace the engine oil before the  
maintenance period arrives.  
NOTE  
The wrench indication/indicator  
light may display/turn on earlier than  
the preset period depending on  
vehicle usage conditions.  
Whenever the engine oil is replaced,  
a reset of the vehicle engine control  
unit is necessary.  
Refer to the Information section in  
the Mazda Connect Owner's  
Manual.  
4-35  
When Driving  
Instrument Cluster and Display  
Active Driving Display*  
Active Driving Display  
▼
1. Display  
2. Dust-proof sheet  
WARNING  
Always adjust the display brightness and position with the vehicle stopped:  
Adjusting the display brightness and position while driving the vehicle is dangerous  
as doing so could distract your attention from the road ahead and lead to an  
accident.  
CAUTION  
Do not place beverages near the dust-proof sheet of the active driving display. If  
water or other liquids are splashed on the dust-proof sheet, it could cause  
damage.  
Do not place objects or apply stickers above the active driving display or to the  
dust-proof sheet as they will cause interference.  
NOTE  
Wearing polarized sunglasses will reduce the visibility of the active driving display  
due to the characteristics of the display.  
If the battery has been removed and re-installed or the battery voltage is low, the  
adjusted position may deviate.  
The display may be diꢁcult to view or temporarily aꢀected by weather conditions  
such as rain, snow, light, and temperature.  
If the audio system is removed, the active driving display cannot be operated.  
4-36  
*Some models.  
When Driving  
Instrument Cluster and Display  
The active driving display indicates the following information:  
*
Lane Departure Warning System (LDWS) Warnings  
Refer to Lane Departure Warning System (LDWS) on page 4-106.  
Blind Spot Monitoring (BSM) Operation Conditions and Warnings  
Refer to Blind Spot Monitoring (BSM) on page 4-107.  
Traꢁc Sign Recognition System (TSR) traꢁc signs and Warnings  
Refer to Traꢁc Sign Recognition System (TSR) on page 4-112.  
*
*
*
Front Cross Traꢁc Alert (FCTA) Operation Conditions and Warning  
Refer to Front Cross Traꢁc Alert (FCTA) on page 4-123.  
*
Mazda Radar Cruise Control (MRCC) Operation Conditions and Warnings  
Refer to Mazda Radar Cruise Control (MRCC) on page 4-130.  
Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop & Go  
*
function) Operation Conditions and Warnings  
Refer to Mazda Radar Cruise Control with Stop & Go function (MRCC with Stop  
& Go function) on page 4-139.  
Traꢁc Jam Assist (TJA) Operation Conditions and Warnings  
*
Refer to Traꢁc Jam Assist (TJA) on page 4-150.  
Lane-keep Assist System (LAS) Warnings  
Refer to Lane-keep Assist System (LAS) on page 4-164.  
Smart Brake Support (SBS) Operation Conditions and Warnings  
Refer to Smart Brake Support (SBS) on page 4-168.  
Cruise Control Operation Conditions  
*
Refer to Cruise Control on page 4-224.  
Navigation Guidance (vehicles with navigation system)  
Intersection Name (vehicles with navigation system)  
Street name (vehicles with navigation system)  
Lane Guidance (vehicles with navigation system)  
Speed limit indicator (vehicles with navigation system)  
Vehicle Speed  
The active driving display settings can be changed or adjusted.  
Refer to the Settings section in the Mazda Connect Owner's Manual.  
NOTE  
The desired driving position (display position, brightness level, display  
information) can be called up after programming the position.  
Refer to Driving Position Memory on page 2-11.  
The street name may not be displayed depending on the market and region.  
4-37  
*Some models.  

Related Topics

When Driving
Start/Stop Engine Manual Transmission Operation Automatic Transmission M Hybrid Switches and Controls Brake ABS/TCS/DSC Drive Selection i-ACTIV AWD Power Steering i-ACTIVSENSE Cruise Control Tire Pressure Monitoring System (TPMS) Rear View Monitor Parking Sensor System

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot