Get Maintenance and Care Guide for Mazda Mx-5 SUV Fourth Generation (2016-2026)

Maintenance and Care

6

How to keep your Mazda in top condition.

Essential Information........................6-2

Appearance Care.............................6-57

Exterior Care.............................. 6-57

Interior Care................................6-67

Introduction.................................. 6-2

Scheduled Maintenance.................... 6-4

Scheduled Maintenance (U.S.A.,

Canada, and Puerto Rico).............6-4

Scheduled Maintenance

(Mexico)..................................... 6-10

Maintenance Monitor................. 6-15

Owner Maintenance........................6-18

Owner Maintenance

Precautions................................. 6-18

Hood........................................... 6-20

Engine Compartment

Overview.................................... 6-22

Engine Oil...................................6-23

Engine Coolant........................... 6-25

Brake/Clutch Fluid..................... 6-26

Washer Fluid...............................6-27

Body Lubrication........................6-28

Wiper Blades.............................. 6-28

Battery........................................ 6-32

Key Battery Replacement...........6-34

Tires............................................6-38

Light Bulbs................................. 6-42

Fuses...........................................6-52

6-1

Maintenance and Care

Essential Information

Introduction

Be careful not to hurt yourself when inspecting your vehicle, replacing a tire, or doing some

kind of maintenance such as car washing. In particular, wear thick work gloves such as

cotton gloves when touching areas that are difficult to see while inspecting or working on

your vehicle. Doing inspections or procedures with your bare hands could cause injury.

If you are unsure about any procedure this manual describes, we strongly urge you to have a

reliable and qualified service shop perform the work, preferably an Authorized Mazda

Dealer.

Factory-trained Mazda technicians and genuine Mazda parts are best for your vehicle.

Without this expertise and the parts that have been designed and made especially for your

Mazda, inadequate, incomplete, and insufficient servicing may result in problems. This

could lead to vehicle damage or an accident and injuries.

For expert advice and quality service, consult an Authorized Mazda Dealer.

To continue warranty eligibility and to protect your investment, it is your responsibility to

properly maintain your vehicle according to factory recommended schedules outlined in this

manual. As part of this you must keep your maintenance records, receipts, repair orders and

any other documents as evidence this maintenance was performed. You must present these

documents, should any warranty coverage disagreement occur. Failure to do so can result in

your warranty being voided either in whole or in part.

This evidence may consist of the following:



The Mazda Scheduled Maintenance Record, refer to the Warranty Booklet, must be

completely filled out showing mileage, repair order number, date for each service, and

signed by a qualified automotive service technician who service vehicles.

Original copies of repair orders or other receipts that include the mileage and date the



vehicle was serviced. Each receipt should be signed by a qualified automotive service

technician.

For self maintenance, a statement that you completed the maintenance yourself,



displaying mileage and the date the work was performed. Also, receipts for the

replacement parts (fluid, filters, etc.) indicating the date and mileage must accompany this

statement.

6-2

Maintenance and Care

Essential Information

NOTE

If you elect to perform maintenance yourself or have your vehicle serviced at a location

other than an Authorized Mazda Dealer, Mazda requires that all fluids, parts and materials

must meet Mazda standards for durability and performance as described in this manual.

Claims against the warranty resulting from lack of maintenance, as opposed to defective

materials or authorized Mazda workmanship, will not be honored.

Any auto repair shop using parts equivalent to your Mazda's original equipment may

perform maintenance. But we recommend that it always be done by an Authorized

Mazda Dealer using genuine Mazda parts.

Selecting “Maintenance Monitor” enables the system to notify you of your vehicle's

approaching inspection/servicing period (page 6-15).

The malfunction diagnosis connector is designed exclusively for connecting the specially

designed device to perform on-board diagnosis.

Do not connect any devices other than the specially designed malfunction diagnosis devices

for servicing. If any device other than the malfunction diagnosis device is connected, it may

affect the vehicle's electrical devices or lead to damage such as battery depletion.

Malfunction

diagnosis

connector

6-3

Maintenance and Care

Scheduled Maintenance

Scheduled Maintenance (U.S.A., Canada, and Puerto

Rico)

Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions

(severe driving conditions)apply.



Repeated short-distance driving

Driving in dusty conditions

Driving with extended use of brakes

Driving in areas where salt or other corrosive materials are used

Driving on rough or muddy roads

Extended periods of idling or low-speed operation

Driving for long periods in cold temperatures or extremely humid climates

Driving in extremely hot conditions



Driving in mountainous conditions continually

If any do apply, follow Schedule 2. (Canada residents follow Schedule 2.)

Vehicles using Engine Oil Flexible Maintenance

Engine Oil Flexible Maintenance is selected by default for U.S.A. and Puerto Rico

residents.

If any following conditions do apply, follow Schedule 2 with engine oil fixed maintenance.



Extended periods of idling or low-speed operation such as police car, taxi or driving

school car

Driving in dusty conditions



The vehicle calculates the remaining oil life based on engine operating conditions. The

vehicle lets you know when an oil change is due by illuminating the wrench indicator light

in the instrument cluster. Change the oil as soon as possible within the next 1,000 km (600

mile) or 15 days. Refer to Maintenance Monitor on page 6-15 for the details.

NOTE



Please ensure that the Flexible Oil Maintenance Setting is reset after each Oil and Filter

replacement.



For maintenance guidelines beyond the miles/months listed, follow the maintenance

intervals provided in the Scheduled Maintenance Tables.

6-4

Maintenance and Care

Scheduled Maintenance

Schedule 1

▼

U.S.A. and Puerto Rico residents - Engine oil flexible maintenance interval

Use when the maintenance monitor for “Oil Change” is set to “Flexible”. For details,

see maintenance monitor. (page 6-15)

Number of months or kilometers (miles), whichever comes first.

Months

×1000 km

×1000 miles

12

24

15

36

48

30

60

72

45

84

96

60

Maintenance Interval

7.5

22.5

37.5

52.5

Spark plugs

Replace every 120,000 km (75,000 miles).

Air filter

R

I

R

I

Drive belts

Replace when wrench indicator light is ON. (Max interval:12

months or 12,000 km (7,500 miles))

*1

Engine oil & filter

Replace at first 192,000 km (120,000 miles) or 10 years; after

that, every 96,000 km (60,000 miles) or 5 years.

*2

Engine coolant

*3

I

Fuel lines and hoses

*3

Hoses and tubes for emission

Brake lines, hoses and connections

Disc brakes

I

Manual transmission oil

Tire (Rotation)

Replace every 96,000 km (60,000 miles) or 4 years.

Rotate every 12,000 km (7,500 miles).

Steering operation and linkages

I

Front and rear suspension, ball joints and wheel

bearing axial play

I

*4

Rear differential oil

Driveshaft dust boots

I

Bolts and nuts on chassis and body

Exhaust system and heat shields

T

I

*5

Inspect annually.

Emergency flat tire repair kit (if equipped)

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.

R: Replace

L: Lubricate

C: Clean

T: Tighten

D: Drain

6-5

Maintenance and Care

Scheduled Maintenance

Remarks:

*

1

The engine oil and filter must be changed at least once a year or within 12,000 km (7,500 miles) since last

engine oil and filter change. Reset the engine oil data whenever replacing the engine oil regardless of the

message/wrench indicator light display.

*

2

3

Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

According to state/provincial and federal regulations, failure to perform maintenance on these items will not

void your emissions warranties. However, Mazda recommends that all maintenance services be performed at

the recommended time or mileage/kilometer period to ensure long-term reliability.

If this component has been submerged in water, the oil should be replaced.

*

4

5

Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the

tire repair fluid bottle with new one before the expiration date.

Schedule 2

▼

U.S.A. and Puerto Rico residents - Severe driving conditions maintenance interval

Number of months or kilometers (miles), whichever comes first.

Months

×1000 km

×1000 miles

6

8

5

12 18 24 30 36 42 48 54 60 66 72

16 24 32 40 48 56 64 72 80 88 96

10 15 20 25 30 35 40 45 50 55 60

Replace every 120,000 km (75,000 miles).

Maintenance Interval

Spark plugs

*1

R

I

Air filter

Drive belts

I

Replace when wrench indicator light is ON. (Max interval:12

months or 12,000 km (7,500 miles))

*2

Flexible

Engine oil & filter

Fixed

R

Replace at first 192,000 km (120,000 miles) or 10 years; after

that, every 96,000 km (60,000 miles) or 5 years.

*3

Engine coolant

Engine coolant level

I

*4

Fuel lines and hoses

*4

Hoses and tubes for emission

Function of all lights

I

Brake lines, hoses and connections

Brake and clutch fluid level

Disc brakes

I

Manual transmission oil

Tire (Rotation)

Replace every 48,000 km (30,000 miles) or 2 years.

Rotate every 8,000 km (5,000 miles).

Tire inflation pressure and tire wear

Steering operation and linkages

I

Front and rear suspension, ball joints and wheel

bearing axial play

I

*5

Rear differential oil

6-6

Maintenance and Care

Scheduled Maintenance

Number of months or kilometers (miles), whichever comes first.

Months

×1000 km

×1000 miles

6

8

5

12 18 24 30 36 42 48 54 60 66 72

16 24 32 40 48 56 64 72 80 88 96

10 15 20 25 30 35 40 45 50 55 60

Maintenance Interval

Driveshaft dust boots

I

Bolts and nuts on chassis and body

Exhaust system and heat shields

All locks and hinges

T

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

Washer fluid level

*6

Inspect annually.

Emergency flat tire repair kit (if equipped)

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.

R: Replace

L: Lubricate

C: Clean

T: Tighten

D: Drain

Remarks:

*

1

2

If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air filter more often

than the recommended intervals.

Engine oil flexible maintenance is available for U.S.A. and Puerto Rico residents whose vehicle is operated

mainly where none of the following conditions apply.

*



Extended periods of idling or low-speed operation such as police car, taxi or driving school car



Driving in dusty conditions

If any do apply, follow fixed maintenance.

The engine oil and filter must be changed at least once a year or within 12,000 km (7,500 miles) since last

engine oil and filter change. Reset the engine oil data whenever replacing the engine oil regardless of the

message/wrench indicator light display.

Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

According to state/provincial and federal regulations, failure to perform maintenance on these items will not

void your emissions warranties. However, Mazda recommends that all maintenance services be performed at

the recommended time or mileage/kilometer period to ensure long-term reliability.

If this component has been submerged in water, the oil should be replaced.

Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the

tire repair fluid bottle with new one before the expiration date.

*

3

4

*

5

6

6-7

Maintenance and Care

Scheduled Maintenance

Canada residents

Number of months or kilometers (miles), whichever comes first.

Months

×1000 km

×1000 miles

6

8

5

12 18 24 30 36 42 48 54 60 66 72

16 24 32 40 48 56 64 72 80 88 96

10 15 20 25 30 35 40 45 50 55 60

Replace every 120,000 km (75,000 miles).

Maintenance Interval

Spark plugs

I

Air filter

Replace every 56,000 km (35,000 miles) or 3 years.

I

Drive belts

I

Engine oil & filter

R

Replace at first 192,000 km (120,000 miles) or 10 years; after

that, every 96,000 km (60,000 miles) or 5 years.

*1

Engine coolant

Engine coolant level

I

*2

Fuel lines and hoses

*2

Hoses and tubes for emission

Function of all lights

I

Brake lines, hoses and connections

Brake and clutch fluid level

Disc brakes

Inspect every 24,000 km (15,000 miles) or 1 year.

Replace every 48,000 km (30,000 miles) or 2 years.

Rotate every 8,000 km (5,000 miles).

Manual transmission oil

Tire (Rotation)

Tire inflation pressure and tire wear

Steering operation and linkages

I

Front and rear suspension, ball joints and wheel

bearing axial play

I

*3

Rear differential oil

Driveshaft dust boots

I

Bolts and nuts on chassis and body

Exhaust system and heat shields

All locks and hinges

T

Inspect every 72,000 km (45,000 miles) or 5 years.

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

Washer fluid level

*4

Inspect annually.

Emergency flat tire repair kit (if equipped)

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.

R: Replace

L: Lubricate

C: Clean

T: Tighten

D: Drain

6-8

Maintenance and Care

Scheduled Maintenance

Remarks:

*

1

2

Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

According to state/provincial and federal regulations, failure to perform maintenance on these items will not

void your emissions warranties. However, Mazda recommends that all maintenance services be performed at

the recommended time or mileage/kilometer period to ensure long-term reliability.

If this component has been submerged in water, the oil should be replaced.

*

3

4

Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the

tire repair fluid bottle with new one before the expiration date.

6-9

Maintenance and Care

Scheduled Maintenance

Scheduled Maintenance (Mexico)

Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions

(severe driving conditions) apply.



Repeated short-distance driving

Driving in dusty conditions

Driving with extended use of brakes

Driving in areas where salt or other corrosive materials are used

Driving on rough or muddy roads

Extended periods of idling or low-speed operation

Driving for long periods in cold temperatures or extremely humid climates

Driving in extremely hot conditions



Driving in mountainous conditions continually

If any do apply, follow Schedule 2.

NOTE

For maintenance guidelines beyond the kilometers/months listed, follow the maintenance

intervals provided in the Scheduled Maintenance Tables.

Schedule 1

▼

Number of months or kilometers, whichever comes first

Maintenance Interval

Months

6

12 18 24 30 36 42 48 54 60 66 72

×1000 km

10 20 30 40 50 60 70 80 90 100 110 120

Drive belts

I

R

I

R

I

R

I

Engine oil & filter

Cooling system

R

Replace at first 200,000 km or 10 years; after that, every

100,000 km or 5 years

*1

Engine coolant

Air filter

R

I

*2

Fuel lines and hoses

Hoses and tubes for emission

Fuel filter

I

*2

I

Replace every 60,000 km

I

Spark plugs

Replace every 120,000 km

Brake lines, hoses and connections

Brake and clutch fluid level

Brake fluid

I

R

I

R

I

R

I

Disc brakes

I

Manual transmission oil

R

6-10

Maintenance and Care

Scheduled Maintenance

Number of months or kilometers, whichever comes first

Maintenance Interval

Months

6

12 18 24 30 36 42 48 54 60 66 72

×1000 km

10 20 30 40 50 60 70 80 90 100 110 120

Tire (Rotation)

Rotate every 10,000 km

Tire inflation pressure and tire wear

Steering operation and linkages

I

Front and rear suspension, ball joints and wheel

bearing axial play

I

*3

Rear differential oil

Driveshaft dust boots

I

T

I

T

I

T

I

T

I

T

I

T

I

Bolts and nuts on chassis and body

Exhaust system and heat shields

All locks and hinges

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

L

I

Washer fluid level

*4

Inspect annually.

Emergency flat tire repair kit (if equipped)

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.

R: Replace

L: Lubricate

C: Clean

T: Tighten

D: Drain

Remarks:

*

1

2

Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

According to state/provincial and federal regulations, failure to perform maintenance on these items will not

void your emissions warranties. However, Mazda recommends that all maintenance services be performed at

the recommended time or kilometer period to ensure long-term reliability.

*

3

4

If this component has been submerged in water, the oil should be replaced.

Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the

tire repair fluid bottle with new one before the expiration date.

6-11

Maintenance and Care

Scheduled Maintenance

Schedule 2

▼

Number of months or kilometers, whichever comes first

Maintenance Interval

Months

3

5

6

9

12 15 18 21 24 27 30 33 36

×1000 km

10 15 20 25 30 35 40 45 50 55 60

Drive belts

I

Engine oil & filter

Cooling system

R

I

R

Replace at first 200,000 km or 10 years; after that, every

100,000 km or 5 years

*1

Engine coolant

Engine coolant level

Air filter

I

C

R

C

R

C

R

*2

Fuel lines and hoses

Hoses and tubes for emission

Fuel filter

I

*2

I

Replace every 60,000 km

I

Spark plugs

Replace every 120,000 km

Function of all lights

I

Brake lines, hoses and connections

Brake and clutch fluid level

Brake fluid

R

I

Disc brakes

I

Manual transmission oil

Tire (Rotation)

R

Rotate every 10,000 km

Tire inflation pressure and tire wear

Steering operation and linkages

I

Front and rear suspension, ball joints and wheel

bearing axial play

I

*3

Rear differential oil

Driveshaft dust boots

I

T

I

T

I

T

I

Bolts and nuts on chassis and body

Exhaust system and heat shields

All locks and hinges

L

I

L

I

L

I

L

I

L

I

L

I

Washer fluid level

*4

Inspect annually.

Emergency flat tire repair kit (if equipped)

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.

R: Replace

L: Lubricate

6-12

Maintenance and Care

Scheduled Maintenance

C: Clean

T: Tighten

D: Drain

Remarks:

*

1

2

Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

According to state/provincial and federal regulations, failure to perform maintenance on these items will not

void your emissions warranties. However, Mazda recommends that all maintenance services be performed at

the recommended time or kilometer period to ensure long-term reliability.

*

3

4

If this component has been submerged in water, the oil should be replaced.

Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the

tire repair fluid bottle with new one before the expiration date.

(Cont.)

Number of months or kilometers, whichever comes first

Maintenance Interval

Months

×1000 km

39 42 45 48 51 54 57 60 63 66 69 72

65 70 75 80 85 90 95 100 105 110 115 120

Drive belts

I

R

I

R

I

Engine oil & filter

Cooling system

R

Replace at first 200,000 km or 10 years; after that, every

100,000 km or 5 years

*1

Engine coolant

Engine coolant level

Air filter

I

R

I

C

R

C

R

C

*2

Fuel lines and hoses

Hoses and tubes for emission

Fuel filter

I

*2

I

Replace every 60,000 km

I

Spark plugs

Replace every 120,000 km

Function of all lights

I

Brake lines, hoses and connections

Brake and clutch fluid level

Brake fluid

R

I

R

I

Disc brakes

I

Manual transmission oil

Tire (Rotation)

R

Rotate every 10,000 km

Tire inflation pressure and tire wear

Steering operation and linkages

I

Front and rear suspension, ball joints and wheel

bearing axial play

I

6-13

Maintenance and Care

Scheduled Maintenance

Number of months or kilometers, whichever comes first

Maintenance Interval

Months

39 42 45 48 51 54 57 60 63 66 69 72

×1000 km

65 70 75 80 85 90 95 100 105 110 115 120

*3

Rear differential oil

Driveshaft dust boots

I

T

I

T

I

T

I

Bolts and nuts on chassis and body

Exhaust system and heat shields

All locks and hinges

L

I

L

I

L

I

L

I

L

I

L

I

Washer fluid level

*4

Inspect annually.

Emergency flat tire repair kit (if equipped)

Chart symbols:

I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.

R: Replace

L: Lubricate

C: Clean

T: Tighten

D: Drain

Remarks:

*

1

2

Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may

cause serious damage to the engine and cooling system.

According to state/provincial and federal regulations, failure to perform maintenance on these items will not

void your emissions warranties. However, Mazda recommends that all maintenance services be performed at

the recommended time or kilometer period to ensure long-term reliability.

*

3

4

If this component has been submerged in water, the oil should be replaced.

Check the tire repair fluid expiration date every year when performing the periodic maintenance. Replace the

tire repair fluid bottle with new one before the expiration date.

6-14

Maintenance and Care

Scheduled Maintenance

Maintenance Monitor

▼

1. Select the

icon on the home screen to display the Applications screen.

2. Select “Vehicle Status Monitor”.

3. Select “Maintenance” to display the maintenance list screen.

4. Switch the tab and select the setting item you want to change.

You can customize settings in the setup display as follows:

U.S.A. and Puerto Rico

Tab

Item

Explanation

Notification can be switched on/off.

Setting

Time (months)

Displays the time or distance until maintenance is due.

Select this item to set the maintenance period.

The wrench indication/indicator light in the instrument cluster

will be illuminated when the remaining distance is less than 1,000

km or 600 mile, or the remaining number of days is less than 15

(whichever comes first).

Distance (mile or km)

Scheduled

Resets the time and distance to the initial values.

Once the system turns on, it needs to be reset whenever carrying

out maintenance.

Reset

Setting

Notification can be switched on/off.

Displays the distance until tire rotation is due.

Select this item to set the tire rotation distance.

The wrench indication/indicator light in the instrument cluster

will be illuminated when the remaining distance is less than 1,000

km or 600 mile.

Distance (mile or km)

Reset

Tire Rotation

Resets the remaining distance to the initial value.

Once the system turns on, it needs to be reset whenever rotating

the tires.

6-15

Maintenance and Care

Scheduled Maintenance

Tab

Item

Explanation

Oil replacement period can be selected from the flexible setting

or fixed setting.

Once engine oil flexible maintenance is selected, the vehicle cal‐

culates the remaining oil life based on the engine operating condi‐

tions.

Setting Interval

The vehicle lets you know when an oil change is due by illumi‐

nating the wrench indication/indicator light in the instrument

cluster.

Displays the distance until the oil replacement is due.

Select this item to set the oil replacement distance.

(Displays only in fixed set‐ The wrench indication/indicator light in the instrument cluster

Distance (mile or km)

Oil Change

ting)

will be illuminated when the remaining distance is less than 1,000

km or 600 mile.

Displays the distance until the oil replacement is due.

The wrench indication/indicator light in the instrument cluster

will be illuminated when the remaining distance is less than 1,000

km or 600 mile.

Distance (mile or km)

(Displays only in flexible

setting)

Resets the remaining distance to the initial value.

Once the system turns on, it needs to be reset whenever replacing

the engine oil.

Reset

6-16

Maintenance and Care

Scheduled Maintenance

Canada and Mexico

Tab

Item

Explanation

Setting

Notification can be switched on/off.

Time (months)

Displays the time or distance until maintenance is due.

Select this item to set the maintenance period.

The wrench indication/indicator light in the instrument cluster

will be illuminated when the remaining distance is less than 1,000

km or 600 mile, or the remaining number of days is less than 15

(whichever comes first).

Distance (km or mile)

Scheduled

Resets the time and distance to the initial values.

Once the system turns on, it needs to be reset whenever carrying

out maintenance.

Reset

Setting

Notification can be switched on/off.

Displays the distance until tire rotation is due.

Select this item to set the tire rotation distance.

The wrench indication/indicator light in the instrument cluster

will be illuminated when the remaining distance is less than 1,000

km or 600 mile.

Distance (km or mile)

Tire Rotation

Resets the remaining distance to the initial value.

Once the system turns on, it needs to be reset whenever rotating

the tires.

Reset

Oil replacement period can be selected from the fixed setting.

The vehicle lets you know when an oil change is due by illumi‐

nating the wrench indicator light in the instrument cluster.

Setting Interval

Displays the distance until the oil replacement is due.

Select this item to set the oil replacement distance.

The wrench indication/indicator light in the instrument cluster

will be illuminated when the remaining distance is less than 1,000

km or 600 mile.

Oil Change

Distance (km or mile)

Reset

Resets the remaining distance to the initial value.

Once the system turns on, it needs to be reset whenever replacing

the engine oil.

6-17

Maintenance and Care

Owner Maintenance

Owner Maintenance Precautions

The owner or a qualified service technician should make these vehicle inspections at the

indicated intervals to ensure safe and dependable operation.

Bring any problem to the attention of an Authorized Mazda Dealer or qualified service

technician as soon as possible.

When Refueling



Brake and clutch fluid level (page 6-26)

Engine coolant level (page 6-25)

Engine oil level (page 6-24)

Washer fluid level (page 6-27)



At Least Monthly



Tire inflation pressures (page 6-38)

At Least Twice a Year (For Example, Every Spring and Fall)

You can do the following scheduled maintenance items if you have some mechanical ability

and a few basic tools and if you closely follow the directions in this manual.



Engine coolant (page 6-25)

Engine oil (page 6-23)



Improper or incomplete service may result in problems. This section gives instructions only

for items that are easy to perform.

As explained in the Introduction (page 6-2), several procedures can be done only by a

qualified service technician with special tools.

Improper owner maintenance during the warranty period may affect warranty coverage.

Refer to Introduction (page 6-2) for owner's responsibility in protecting your investment.

For details, read the separate Mazda Warranty statement provided with the vehicle. If you

are unsure about any servicing or maintenance procedure, have it done by an Authorized

Mazda Dealer.

There are strict environmental laws regarding the disposal of waste oil and fluids. Please

dispose of your waste properly and with due regard to the environment.

We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized

Mazda Dealer.

6-18

Maintenance and Care

Owner Maintenance

WARNING

Do not perform maintenance workif you lacksuꢀcient knowledge and experience or the

proper tools and equipment to do the work. Have maintenance workdone by a qualiꢁed

technician:

Performing maintenance work on a vehicle is dangerous if not done properly. You can be

seriously injured while performing some maintenance procedures.

If you must run the engine while working under the hood, make certain that you remove all

jewelry (especially rings, bracelets, watches, and necklaces) and all neckties, scarves, and

similar loose clothing before getting near the engine or cooling fan which may turn on

unexpectedly:

Working under the hood with the engine running is dangerous. It becomes even more

dangerous when you wear jewelry, loose clothing or have long hair or a long beard.

Either can become entangled in moving parts and result in injury.

Pull over to a safe location, then switch the ignition oꢂ and make sure the fan is not

running before attempting to worknear the cooling fan:

Working near the cooling fan when it is running is dangerous. The fan could continue running

indeꢀnitely even if the engine has stopped and the engine compartment temperature is high.

You could be hit by the fan and seriously injured.

Do not leave items in the engine compartment:

After you have ꢀnished checking or doing servicing in the engine compartment, do not forget

and leave items such as tools or rags in the engine compartment.

Tools or other items left in the engine compartment could cause engine damage or a ꢀre

leading to an unexpected accident.

6-19

Maintenance and Care

Owner Maintenance

2. Insert your hand into the hood

opening, slide the latch lever to the

right, and lift up the hood.

Hood

WARNING

Always checkthat the hood is closed and

securely locked:

A hood that is not closed and securely

locked is dangerous as it could ꢁy open

while the vehicle is moving and block the

driver's vision which could result in a

serious accident.

Lever

Opening the Hood

▼

1. With the vehicle parked, pull the

release handle to unlock the hood.

3. Grasp the support rod in the padded

area and secure it in the support rod

hole indicated by the arrow to hold the

hood open.

Pad

Support rod

Clip

Release handle

6-20

Maintenance and Care

Owner Maintenance

Closing the Hood

▼

1. Check under the hood area to make

certain all filler caps are in place and

all loose items (e.g. tools, oil

containers, etc.) have been removed.

2. Lift the hood, grasp the padded area on

the support rod, and secure the support

rod in the clip. Verify that the support

rod is secured in the clip before closing

the hood.

Pad

Clip

3. Lower the hood slowly to a height of

about 20 cm (7.9 in) above its closed

position and then let it drop.

CAUTION

When closing the hood, do not push it

excessively such as by applying your

weight. Otherwise, the hood could be

deformed.

6-21

Maintenance and Care

Owner Maintenance

Engine Compartment Overview

Brake/Clutch fluid reservoir

Engine oil dipstick

Engine oil-filler cap

Windshield washer fluid reservoir

Cooling system cap

Battery

Fuse block

Engine coolant reservoir

6-22

Maintenance and Care

Owner Maintenance

Only use SAE 0W-20 oil “Certified For

Gasoline Engines” by the American

Petroleum Institute (API).

Oil with this trademark symbol conforms

to the current engine and emission system

protection standards and fuel economy

requirements of the International

Lubricant Standardization and Approval

Committee (ILSAC), comprised of U.S.

and Japanese automobile manufacturers.

Engine Oil

NOTE

Changing the engine oil should be

performed by an Authorized Mazda

Dealer.

Refer to Introduction (page 6-2) for

owner's responsibility in protecting your

investment.

Recommended Oil

▼

–40

–20

0

20

10

30 40

–30

–10

U.S.A., Canada, and Puerto Rico

Use SAE 0W-20 engine oil.

Mazda Genuine Oil is used in your Mazda

vehicle. Mazda Genuine 0W-20 Oil is

required to achieve optimum fuel

economy.

–40 –20

0

20

40 60

80 100

For maintenance service, Mazda

recommends Mazda Genuine Parts and

Oil.

(ILSAC)

6-23

Maintenance and Care

Owner Maintenance

Except U.S.A., Canada, and Puerto Rico

Inspecting Engine Oil Level

▼

Use SAE 5W-30 engine oil.

Oil container labels provide important

information.

A chief contribution this type of oil makes

to fuel economy is reducing the amount of

fuel necessary to overcome engine

friction.

1. Be sure the vehicle is on a level

surface.

2. Warm up the engine to normal

operating temperature.

3. Turn it off and wait at least 5 minutes

for the oil to return to the oil pan.

4. Pull out the dipstick, wipe it clean, and

reinsert it fully.

For maintenance service, Mazda

recommends Mazda Genuine Parts.

MAX

OK

MIN

(ILSAC)

5. Pull it out again and examine the level.

The level is normal if it is between the

MIN and MAX marks.

(Mexico)

If it is near or below MIN, add enough

oil to bring the level to MAX.

Use SAE 5W-30 engine oil. If SAE 5W-30

engine oil is not available, use SAE 5W-20

engine oil.

CAUTION

The quality designation SM, or ILSAC

must be on the label.

Do not overꢀll the engine oil. This may

cause engine damage.

6. Make sure the O-ring on the dipstick is

positioned properly before reinserting

the dipstick.

20

–40

–20

0

10

30 40

–30

–10

–40 –20

80 100

0

20

40 60

7. Reinsert the dipstick fully.

6-24

Maintenance and Care

Owner Maintenance

NOTE

Engine Coolant

Changing the coolant should be done by

an Authorized Mazda Dealer.

Inspecting Coolant Level

▼

Inspect the antifreeze protection and

coolant level in the coolant reservoir at

least once a year―at the beginning of the

winter season―and before traveling where

temperatures may drop below freezing.

WARNING

Do not use a match or live ꢃame in the

engine compartment. DO NOT ADD

COOLANT WHEN THE ENGINE IS HOT:

A hot engine is dangerous. If the engine has

been running, parts of the engine

compartment can become very hot. You

could be burned. Carefully inspect the

engine coolant in the coolant reservoir, but

do not open it.

Inspect the condition and connections of

all cooling system and heater hoses.

Replace any that are swollen or

deteriorated.

The coolant should be at full in the

radiator and between the FULL and LOW

marks on the coolant reservoir when the

engine is cool.

Pull over to a safe location, then switch

the ignition oꢂ and make sure the fan is

not running before attempting to work

near the cooling fan:

Cooling system cap

Coolant reservoir

Working near the cooling fan when it is

running is dangerous. The fan could

continue running indeꢀnitely even if the

engine has stopped and the engine

compartment temperature is high. You

could be hit by the fan and seriously

injured.

Cooling fan

If it is at or near LOW, add enough coolant

to the coolant reservoir to provide freezing

and corrosion protection and to bring the

level to FULL.

Securely tighten the coolant reservoir tank

cap after adding coolant.

Do not remove either cooling

system cap when the engine and radiator

are hot:

When the engine and radiator are hot,

scalding coolant and steam may shoot out

under pressure and cause serious injury.

6-25

Maintenance and Care

Owner Maintenance

Brake/Clutch Fluid

CAUTION

Inspecting Brake/Clutch Fluid Level

▼

Radiator coolant will damage paint.

Rinse it oꢂ quickly if spilled.

WARNING

If the “FL22” mark is shown on or near

the cooling system cap, use of FL-22 is

recommended when replacing engine

coolant. Using engine coolant other than

FL-22 may cause serious damage to the

engine and cooling system.

If the brake/clutch ꢃuid level is low, have

the brakes inspected:

A low brake/clutch ꢁuid level is dangerous.

A low level could indicate brake lining wear

or a brake system leak which could cause

the brakes to fail and lead to an accident.

The brakes and clutch draw fluid from the

same reservoir.

Inspect the fluid level in the reservoir

regularly. It should be kept between the

MAX and MIN lines.

The level normally drops with

accumulated distance, a condition

associated with wear of brake and clutch

linings. If it is excessively low, have the

brake/clutch system inspected by an

Authorized Mazda Dealer.

If the coolant reservoir is empty or new

coolant is required frequently, consult an

Authorized Mazda Dealer.

6-26

Maintenance and Care

Owner Maintenance

Inspect fluid level in the washer fluid

reservoir; add fluid if necessary.

Washer Fluid

Inspecting Washer Fluid Level

▼

WARNING

Use only windshield washer ꢃuid or plain

water in the reservoir:

Using radiator antifreeze as washer ꢁuid is

dangerous. If sprayed on the windshield, it

will dirty the windshield, aꢂect your

visibility, and could result in an accident.

Use plain water if washer fluid is

unavailable.

Using Washer Fluid Without Anti-freeze

Protection in Cold Weather:

But use only washer fluid in cold weather

to prevent it from freezing.

Operating your vehicle in temperatures

below 4 °C (40 °F) using washer ꢁuid

without anti-freeze protection is dangerous

as it could cause impaired windshield

vision and result in an accident. In cold

weather, always use washer ꢁuid with

anti-freeze protection.

NOTE

State or local regulations may restrict the

use of volatile organic compounds

(VOCs), which are commonly used as

anti-freeze agents in washer fluid. A

washer fluid with limited VOC content

should be used only if it provides adequate

freeze resistance for all regions and

climates in which the vehicle will be

operated.

6-27

Maintenance and Care

Owner Maintenance

Body Lubrication

Wiper Blades

All moving points of the body, such as

door and hood hinges and locks, should be

lubricated each time the engine oil is

changed. Use a nonfreezing lubricant on

locks during cold weather.

CAUTION

Hot waxes applied by automatic car

washers have been known to aꢂect the

wiper's ability to clean windows.

To prevent damage to the wiper blades,

do not use gasoline, kerosene, paint

thinner, or other solvents on or near

them.

Make sure the hood's secondary latch

keeps the hood from opening when the

primary latch is released.

When the wiper lever is in the AUTO

position and the ignition is switched ON,

the wipers may move automatically in

the following cases:

If the windshield above the rain sensor

is touched.

If the windshield above the rain sensor

is wiped with a cloth.

If the windshield is struck with a hand

or other object.

If the rain sensor is struck with a hand

or other object from inside the vehicle.

Be careful not to pinch hands or ꢀngers

as it may cause injury, or damage the

wipers. When washing or servicing the

vehicle, make sure the wiper lever is in

the OFF position.

Contamination of either the windshield or

the blades with foreign matter can reduce

wiper effectiveness. Common sources are

insects, tree sap, and hot wax treatments

used by some commercial car washes.

If the blades are not wiping properly, clean

the window and blades with a good

cleaner or mild detergent; then rinse

thoroughly with clean water. Repeat if

necessary.

6-28

Maintenance and Care

Owner Maintenance

3. Tilt the blade assembly and remove it

from the arm.

Replacing Windshield Wiper Blades

▼

When the wipers no longer clean well, the

blades are probably worn or cracked.

Replace them.

CAUTION

To prevent damage to the wiper arms and

other components, do not try to sweep the

wiper arm by hand.

NOTE

When raising both windshield wiper arms,

raise the driver's side wiper arm first.

When lowering the wiper arms, slowly

lower the wiper arm from the passenger's

side first while supporting it with your

hand. Forcefully lowering the wiper arms

could damage the wiper arm and blade,

and may scratch or crack the windshield.

CAUTION

To prevent damage to the windshield

let the wiper arm down easily, do not

let it slap down on the windshield.

4. Pull down the blade rubber and slide it

out of blade holder.

Replace the wiper blades using the

following procedure.

(Type A)

1. Raise the wiper arm.

2. Open the clip and slide the blade

assembly in the direction of the arrow.

5. Remove the metal stiffeners from each

blade rubber and install them in the

new blade.

6-29

Maintenance and Care

Owner Maintenance

CAUTION

To prevent damage to the windshield

let the wiper arm down easily, do not

let it slap down on the windshield.

2. Hold the end of the rubber and pull

until the tabs are free of the metal

support.

Do not bend or discard the stiꢂeners.

You need to use them again.

If the metal stiꢂeners are switched,

the blade's wiping eꢃciency could be

reduced.

So do not use the driver's side metal

stiꢂeners on the passenger's side, or

vice versa.

Metal support

Be sure to reinstall the metal

stiꢂeners in the new blade rubber so

that the curve is the same as it was in

the old blade rubber.

Tab

6. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

3. Remove the metal stiffeners from each

blade rubber and install them in the

new blade.

(Type B)

1. Raise the wiper arm and turn the blade

assembly to expose the plastic locking

clip.

Compress the clip and slide the

assembly downward; then lift it off the

arm.

Plastic locking clip

6-30

Maintenance and Care

Owner Maintenance

CAUTION

Do not bend or discard the stiꢂeners.

You need to use them again.

If the metal stiꢂeners are switched,

the blade's wiping eꢃciency could be

reduced.

So do not use the driver's side metal

stiꢂeners on the passenger's side, or

vice versa.

Be sure to reinstall the metal

stiꢂeners in the new blade rubber so

that the curve is the same as it was in

the old blade rubber.

4. Carefully insert the new blade rubber.

Then install the blade assembly in the

reverse order of removal.

NOTE

Install the blade so that the tabs are

toward the bottom of the wiper arm.

6-31

Maintenance and Care

Owner Maintenance

Battery

WARNING

Wash hands after handling the battery and related accessories:

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and reproductive harm.

Read the following precautions carefully before using the battery or inspecting to

ensure safe and correct handling:

Always wear eye protection when working near the battery:

Working without eye protection is dangerous. Battery ꢁuid contains SULFURIC ACID which

could cause blindness if splashed into your eyes. Also, hydrogen gas produced during normal

battery operation, could ignite and cause the battery to explode.

Wear eye protection and protective gloves to prevent contact with battery ꢃuid:

Spilled battery ꢁuid is dangerous.

Battery ꢁuid contains SULFURIC ACID which could cause serious injuries if it gets in eyes, or on

the skin or clothing. If this happens, immediately ꢁush your eyes with water for 15 minutes or

wash your skin thoroughly and get medical attention.

Always keep batteries out of the reach of children:

Allowing children to play near batteries is dangerous. Battery ꢁuid could cause serious injuries

if it gets in the eyes or on the skin.

6-32

Maintenance and Care

Owner Maintenance

Keep ꢃames and sparks away from open battery cellsand do not allow metal tools to

contact the positive ( ) or negative ( ) terminal of the battery when working near a battery.

Do not allow the positive ( ) terminal to contact the vehicle body:

Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced during

normal battery operation, could ignite and cause the battery to explode. An exploding battery

can cause serious burns and injuries. Keep all ꢁames including cigarettes and sparks away

from open battery cells.

Keep all ꢃames and sparks away from open battery cells because hydrogen gas is

produced from open battery cells while charging the battery or adding battery ꢃuid:

Flames and sparks near open battery cells are dangerous. Hydrogen gas, produced during

normal battery operation, could ignite and cause the battery to explode. An exploding battery

can cause serious burns and injuries. Keep all ꢁames including cigarettes and sparks away

from open battery cells.

NOTE

Before performing battery maintenance, remove the battery cover.

6-33

Maintenance and Care

Owner Maintenance

Battery Maintenance

▼

Key Battery Replacement

If the buttons on the transmitter are

inoperable and the operation indicator

light does not flash, the battery may be

dead.

Replace with a new battery before the

transmitter becomes unusable.

CAUTION

Make sure the battery is installed

correctly. Battery leakage could occur if it

is not installed correctly.

To get the best service from a battery:



Keep it securely mounted.

Keep the top clean and dry.

Keep terminals and connections clean,

When replacing the battery, be careful

not to touch any of the internal circuitry

and electrical terminals, bend the

electrical terminals, or get dirt in the

transmitter as the transmitter could be

damaged.



tight, and coated with petroleum jelly or

terminal grease.

Rinse off spilled electrolyte immediately



with a solution of water and baking

soda.

If the vehicle will not be used for an

There is the danger of explosion if the

battery is not correctly replaced.

Dispose of used batteries according to

the following instructions.



extended time, disconnect the battery

cables and charge the battery every 6

weeks.

Insulate the plus and minus terminals

of the battery using cellophane or

equivalent tape.

Battery Replacement

▼

Contact an Authorized Mazda Dealer for

battery replacement.

Never disassemble.

Never throw the battery into ꢀre or

water.

Never deform or crush.

Replace only with the same type battery.

(Type A)

Use CR2025 or an equivalent.

(Type B)

Use CR2032 or an equivalent.

6-34

Maintenance and Care

Owner Maintenance

The following conditions indicate that the

battery power is low:

2. Twist a tape-wrapped flathead

screwdriver in the direction of the

arrow and open the cover slightly.



The KEY indicator light (green) flashes

Cover

in the instrument cluster for about 30

seconds after the engine is switched

OFF (for vehicles with a type A

instrument cluster (page 4-27), messages

are displayed in the instrument cluster).

The system does not operate and the



operation indicator light on the

transmitter does not flash when the

buttons are pressed.



The system's operational range is

reduced.

3. Insert the tape-wrapped flathead

screwdriver into the gap and slide it in

the direction of the arrow.

Cover

Replacing the battery at an Authorized

Mazda Dealer, is recommended to prevent

damage to the key. If replacing the battery

by yourself, follow the instruction.

Replacing the key battery

Type A

Gap

1. Press the knob and pull out the

auxiliary key.

Knob

4. Twist the flathead screwdriver in the

direction of the arrow and remove the

cover.

Cover

6-35

Maintenance and Care

Owner Maintenance

5. Remove the battery cap, then remove

the battery.

6. Insert a new battery with the positive

pole facing up, and then cover the

battery with the battery cap.

7. Close the cover.

CAUTION

Be careful not to allow the rubber

ring shown in the ꢀgure to be

scratched or damaged.

If the rubber ring detaches, reattach

it before inserting a new battery.

8. Reinsert the auxiliary key.

Type B

Rubber ring

1. Remove the lower cover while

pressing the knob in the direction of

the arrow.

6-36

Maintenance and Care

Owner Maintenance

2. Press in the tab to unlock the upper

cover.

5. Remove the cap using the

tape-wrapped flathead screwdriver.

6. Remove the battery using

tape-wrapped flathead screwdriver.

3. Insert a tape-wrapped flathead

screwdriver into the gap and slide it in

the direction of the arrow.

4. Twist the flathead screwdriver in the

direction of the arrow and remove the

upper cover.

7. Insert a new battery into the transmitter

so that the positive pole is facing up.

8. Install the cap.

6-37

Maintenance and Care

Owner Maintenance

9. Install the upper cover.

Tires

For reasons of proper performance, safety,

and better fuel economy, always maintain

recommended tire inflation pressures and

stay within the recommended load limits

and weight distribution.

WARNING

10. Insert the tabs of the lower cover into

the slots of the transmitter and install

the lower cover.

Using Diꢂerent Tire Types:

Driving your vehicle with diꢂerent types of

tires is dangerous. It could cause poor

handling and poor braking; leading to loss

of control.

Except for the limited use of the temporary

spare tire, use only the same type tires

(radial, bias-belted, bias-type) on all four

wheels.

Using Wrong-Sized Tires:

Using any other tire size than what is

speciꢀed for the vehicle (page 9-8) is

dangerous. It could seriously aꢂect ride,

handling, ground clearance, tire clearance,

and speedometer calibration. This could

cause you to have an accident. Use only

tires that are the correct size speciꢀed for

the vehicle.

Tire Inflation Pressure

▼

WARNING

Always inꢃate the tires to the correct

pressure:

Overinꢁation or underinꢁation of tires is

dangerous. Adverse handling or

unexpected tire failure could result in a

serious accident.

Refer to Tires on page 9-8.

6-38

Maintenance and Care

Owner Maintenance

Use only a Mazda-genuine tire valve cap:

Use of a non-genuine part is dangerous as

the correct tire air pressure cannot be

maintained if the tire valve becomes

damaged. If the vehicle is driven under this

condition, the tire air pressure will decrease

which could result in a serious accident. Do

not use any part for the tire valve cap that

is not a Mazda-genuine part.

Tire Rotation

▼

WARNING

Rotate tires periodically:

Irregular tire wear is dangerous. To

equalize tread wear for maintaining good

performance in handling and braking,

rotate the tires every 12,000 km (7,500

miles). However Mazda recommends to

rotate every 8,000 km (5,000 miles) to help

increase tire life and distribute wear more

evenly.

Inspect all tire pressures monthly when the

tires are cold. Maintain recommended

pressures for the best ride, handling, and

minimum tire wear.

Refer to the specification charts (page

9-8).

Refer to Scheduled Maintenance on page

6-4.

NOTE



Always check tire pressure when tires

are cold.

Warm tires normally exceed

During rotation, inspect them for correct

balance.



recommended pressures. Do not release

air from warm tires to adjust the

pressure.



Underinflation can cause reduced fuel

economy, uneven and accelerated tire

wear, and poor sealing of the tire bead,

which will deform the wheel and cause

separation of tire from rim.

Forward



Overinflation can produce a harsh ride,

Do not include (TEMPORARY USE ONLY)

spare tire in rotation.

uneven and accelerated tire wear, and a

greater possibility of damage from road

hazards.

Keep your tire pressure at the correct

levels. If one frequently needs inflating,

have it inspected.

6-39

Maintenance and Care

Owner Maintenance

Also, inspect them for uneven wear and

damage. Abnormal wear is usually caused

by one or a combination of the following:

Replacing a Tire

▼

WARNING



Incorrect tire pressure

Improper wheel alignment

Out-of-balance wheel

Severe braking

Always use tires that are in good condition:

Driving with worn tires is dangerous.

Reduced braking, steering, and traction

could result in an accident.



Replace all four tires at the same time:

Replacing just one tire is dangerous. It

could cause poor handling and poor

braking resulting in loss of vehicle control.

Mazda strongly recommends that you

replace all four tires at the same time.

After rotation, inflate all tire pressures to

specification (page 9-8) and inspect the

lug nuts for tightness.

CAUTION

Rotate unidirectional tires and radial tires

that have an asymmetrical tread pattern or

studs only from front to rear, not from side

to side. Tire performance will be reduced if

rotated from side to side.

If a tire wears evenly, a wear indicator will

appear as a solid band across the tread.

Replace the tire when this happens.

Tread wear indicator

(With limited-slip diꢂerential)

Do not use the following:

Tires not of the designated size

Tires of diꢂerent sizes or types at the

same time

Tires not suꢃciently inꢁated

If these instructions are not followed, the

rotation of the left and right wheels will be

diꢂerent and will thus apply a constant

load on the limited-slip diꢂerential.

This will cause a malfunction.

New tread

Worn tread

You should replace the tire before the band

crosses the entire tread.

6-40

Maintenance and Care

Owner Maintenance

NOTE

Tires degrade over time, even when they

are not being used on the road. It is

recommended that tires generally be

replaced when they are 6 years or older.

Heat caused by hot climates or frequent

high loading conditions can accelerate the

aging process. The period in which the tire

was manufactured (both week and year) is

indicated by a 4-digit number.



When replacing a wheel, make sure the

new one is the same as the original

factory wheel in diameter, rim width,

and offset (inset/outset).

For details, contact an Authorized

Mazda Dealer.



Proper tire balancing provides the best

riding comfort and helps reduce tread

wear. Out-of-balance tires can cause

vibration and uneven wear, such as

cupping and flat spots.

Refer to Tire Labeling on page 8-25.

Replacing a Wheel

▼

WARNING

Always use wheels of the correct size on

your vehicle:

Using a wrong-sized wheel is dangerous.

Braking and handling could be aꢂected,

leading to loss of control and an accident.

CAUTION

A wrong-sized wheel may adversely aꢂect:

Tire ꢀt

Wheel and bearing life

Ground clearance

Snow-chain clearance

Speedometer calibration

Headlight aim

Bumper height

Tire Pressure Monitoring System

6-41

Maintenance and Care

Owner Maintenance

Light Bulbs

Overhead light

Side turn signal lights

Front side-marker lights

Parking lights

Front turn signal lights

Daytime running lights

Headlights (Low/High beam)

Trunk light

High-mount brake light

License plate lights

Rear side-marker lights

Brake lights

Taillights

Reverse lights

Rear turn signal lights

6-42

Maintenance and Care

Owner Maintenance

Replacing Exterior Light Bulbs

▼

CAUTION

Headlights, Daytime running lights

(LED type), Parking lights, High-mount

brake light, Brake lights, Taillights

When removing the lens or lamp unit using

a ꢁathead screwdriver, make sure that the

ꢁathead screwdriver does not contact the

interior terminal. If the ꢁathead screwdriver

contacts the terminal, a short circuit may

occur.

The LED bulb cannot be replaced as a

single unit because it is an integrated unit.

The LED bulb has to be replaced with the

unit. We recommend an Authorized

Mazda Dealer when the replacement is

necessary.

NOTE



To replace the bulb, contact an

Authorized Mazda Dealer.

Use the protective cover and carton for

the replacement bulb to dispose of the

old bulb promptly and out of the reach

of children.

Daytime running lights (Bulb type)



1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Pull the center of each plastic retainer

and remove the retainers.

Removal

Installation

6-43

Maintenance and Care

Owner Maintenance

3. Turn the screw counterclockwise and

remove it, and then partially peel back

the mudguard.

Front side-marker lights

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the right, and turn off

engine. If you are changing the left

bulb, turn the steering wheel to the left.

3. Pull the center of each plastic retainer

and remove the retainers, and then

partially peel back the mudguard.

4. Turn the socket and bulb assembly

counterclockwise and remove it.

Removal

5. Disconnect the bulb from the socket.

Installation

4. Turn the socket and bulb assembly

counterclockwise and remove it.

5. Disconnect the bulb from the socket.

6. Install the new bulb in the reverse

order of the removal procedure.

6. Install the new bulb in the reverse

order of the removal procedure.

6-44

Maintenance and Care

Owner Maintenance

Front turn signal lights

5. Turn the socket and bulb assembly

counterclockwise and remove it.

6. Disconnect the bulb from the socket.

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the right, and turn off

engine. If you are changing the left

bulb, turn the steering wheel to the left.

3. Pull the center of each plastic retainer

and remove the retainers, and then

partially peel back the mudguard.

Removal

7. Install the new bulb in the reverse

order of the removal procedure.

Side turn signal lights

Installation

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. If you are changing the right bulb, start

the engine, turn the steering wheel all

the way to the right, and turn off

4. Disconnect the connector from the unit

by pressing the tab on the connector

with your finger and pulling the

connector rearward.

engine. If you are changing the left

bulb, turn the steering wheel to the left.

6-45

Maintenance and Care

Owner Maintenance

3. Pull the center of each plastic retainer

and remove the retainers, and then

partially peel back the mudguard.

6. Install the new side turn signal unit in

the reverse order of the removal

procedure.

Rear turn signal lights

Removal

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Pull the center of each plastic retainer

and remove the retainers and the trunk

end trim.

Installation

4. Remove the unit by pressing the tab on

the unit with your finger and pulling

the unit forward.

Removal

Installation

5. Detach the electrical connector from

the unit by pulling it to the rear.

6-46

Maintenance and Care

Owner Maintenance

3. Disconnect the connector from the unit

by pressing the tab on the connector

with your finger and pulling the

connector downward.

5. To provide a hole for inserting a finger

to remove the rear combination lamp

unit later in the procedure, pinch the

top and bottom of the grommet shown

in the figure and press it out of the hole

in the direction of the rear combination

lamp unit.

Grommet

4. Pull the center of each plastic retainer

and remove the retainers, and then

Rear combination lamp

unit

partially peel back the trunk side trim.

Body

Grommet

Removal

Installation

6-47

Maintenance and Care

Owner Maintenance

6. Apply protective tape as shown in the

figure. Otherwise, the rear combination

lamp unit will contact the body and

may scratch or damage it.

7. Remove the screw and nut.

Always apply three layers of protective

tape to the area indicated in the figure.

Protective tape

8. To remove the rear combination lamp

unit, insert your finger from inside the

trunk and into the hole from which the

grommet was removed in Step 5, and

while holding the lamp lens (round

part) of the rear combination lamp with

your hand, press the rear combination

lamp unit until the hook detaches from

the clip.

Rear combination

lamp unit

Area specifically in need

of protection

CAUTION

Do not use tape with strong adhesive

strength. Otherwise, the vehicle paint

may peel oꢂ.

Grommet installation

hole

Always apply three layers of

protective tape to the area indicated

in the ꢀgure. Otherwise, the body

may become scratched or damaged

when pulling out the rear

combination lamp unit.

Hook

Rear combination lamp unit

6-48

Maintenance and Care

Owner Maintenance

9. After the hook is detached, pull out the

rear combination lamp unit in the

Rear side-marker lights

1. Make sure the ignition is switched off,

and the headlight switch is off.

direction of the arrow and remove it.

2. Turn the socket and bulb assembly

counterclockwise and remove it.

Rear combination

lamp unit

Clip

3. Disconnect the bulb from the socket.

Hook

Grommet installation hole

CAUTION

Carefully pull out the rear combination

lamp unit when removing it from the

body.

4. Install the new bulb in the reverse

order of the removal procedure.

The wiring may become damaged if the

rear combination lamp unit is forcefully

pulled out.

10. Turn the socket and bulb assembly

counterclockwise and remove it.

11. Disconnect the bulb from the socket.

12. Install the new bulb in the reverse

order of the removal procedure.

6-49

Maintenance and Care

Owner Maintenance

Reverse lights

License plate lights

1. Make sure the ignition is switched off,

and the headlight switch is off.

1. Make sure the ignition is switched off,

and the headlight switch is off.

2. Turn the socket and bulb assembly

counterclockwise and remove it.

3. Disconnect the bulb from the socket.

2. Remove the unit by pressing the tab on

the unit with your finger and pulling

the unit downward.

3. Turn the socket and bulb assembly

counterclockwise and remove it.

4. Disconnect the bulb from the socket.

4. Install the new bulb in the reverse

order of the removal procedure.

5. Install the new bulb in the reverse

order of the removal procedure.

6-50

Maintenance and Care

Owner Maintenance

Trunk light

Replacing Interior Light Bulbs

▼

1. Wrap a small flathead screwdriver with

a soft cloth to prevent damage to the

lens, and then remove the lens by

carefully prying on the edge of the lens

with the flathead screwdriver.

Overhead light

1. Wrap a small flathead screwdriver with

a soft cloth to prevent damage to the

lens, and then remove the lens by

carefully prying on the edge of the lens

with the flathead screwdriver.

2. Disconnect the bulb by pulling it out.

2. Disconnect the connector from the

unit.

3. Disconnect the bulb by pulling it out.

3. Install the new bulb in the reverse

order of the removal procedure.

4. Install the new bulb in the reverse

order of the removal procedure.

6-51

Maintenance and Care

Owner Maintenance

3. Pull the fuse straight out with the fuse

puller provided on the fuse block

Fuses

Your vehicle's electrical system is

protected by fuses.

located in the engine compartment.

If any lights, accessories, or controls do

not work, inspect the appropriate circuit

protector. If a fuse has blown, the inside

element will be melted.

4. Inspect the fuse and replace it if it is

blown.

If the same fuse blows again, avoid using

that system and consult an Authorized

Mazda Dealer as soon as possible.

Fuse Replacement

▼

Replacing the fuses on the vehicle's left

side

If the electrical system does not work, first

inspect the fuses on the vehicle's left side.

Blown

Normal

1. Make sure the ignition is switched off,

and other switches are off.

2. Open the fuse panel cover.

5. Insert a new fuse of the same

amperage rating, and make sure it fits

tightly. If it does not fit tightly, have an

expert install it. We recommend an

Authorized Mazda Dealer.

If you have no spare fuses, borrow one

of the same rating from a circuit not

essential to vehicle operation, such as

the AUDIO or OUTLET circuit.

CAUTION

Always replace a fuse with a genuine

Mazda fuse or equivalent of the same

rating. Otherwise you may damage the

electric system.

6. Reinstall the cover and make sure that

it is securely installed.

6-52

Maintenance and Care

Owner Maintenance

Replacing the fuses under the hood

3. Remove the cover while lifting it

and sliding it to the rear.

If the headlights or other electrical

components do not work and the fuses in

the cabin are normal, inspect the fuse

block under the hood.

If a fuse is blown, it must be replaced.

Follow these steps:

1. Make sure the ignition is switched off,

and other switches are off.

2. Remove the fuse block cover.

3. If any fuse but the MAIN fuse is

blown, replace it with a new one of the

same amperage rating.

NOTE

If the lock is forcefully opened, the fuse

block cover may come in contact with

the frame when it is removed and

become scratched.

When removing the cover, remove it

slowly according to the following

procedure.

1. Disengage the rear lock by

pressing down on the front tab with

your fingers.

Normal

Blown

2. Remove the front tab while slightly

lifting the front of the cover.

WARNING

Do not replace the main fuse by

yourself. Have an Authorized Mazda

Dealer perform the replacement:

Replacing the fuse by yourself is

dangerous because the MAIN fuse is a

high current fuse. Incorrect

replacement could cause an electrical

shock or a short circuit resulting in a

ꢀre.

4. Reinstall the cover and make sure that

it is securely installed.

6-53

Maintenance and Care

Owner Maintenance

Fuse Panel Description

▼

Fuse block (Engine compartment)

FUSE

DESCRIPTION

PROTECTED COMPONENT

RATING

1

2

ENG IG3

ENG IG2

HORN2

C/U IG1

ENG IG1

―

5 A

―

3

7.5 A

15 A

7.5 A

―

Horn

4

For protection of various circuits

Engine control system

―

5

6

7

INTERIOR

15 A

7.5 A

15 A

10 A

7.5 A

―

Overhead light

Engine control system

Audio system

8

ENG

B

9

AUDIO2

METER1

SRS1

10

11

12

13

14

15

16

Instrument cluster

Air bag

―

RADIO

ENGINE3

ENGINE1

ENGINE2

7.5 A

20 A

10 A

15 A

Audio system

―

Engine control system

6-54

Maintenance and Care

Owner Maintenance

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

17

18

AUDIO1

25 A

Audio system

A/C MAG

7.5 A

Air conditioner

AT PUMP

H/L HI

*

19

20 A

Transmission control system

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

AT

D LOCK

H/L RH

ENG B2

TAIL

15 A

25 A

20 A

7.5 A

20 A

15 A

25 A

15 A

20 A

10 A

15 A

20 A

30 A

15 A

5 A

Transmission control system

Power door locks

Headlight (RH)

Engine control system

Taillights, License plate lights, Parking lights

DRL

―

ROOM

Overhead light

FOG

―

H/CLEAN

STOP

―

Brake lights

HORN

Horn

H/L LH

ABS/DSC S

HAZARD

FUEL PUMP

ENG B3

WIPER

Headlight (LH)

ABS, Dynamic stability control system

Hazard warning flashers, Turn signal lights

Fuel system

―

20 A

50 A

―

Windshield wipers

For protection of various circuits

―

CABIN

―

B

ENG SUB

30 A

50 A

Engine control system

ABS, Dynamic stability control system

ABS/DSC M

EVVT

A/R PUMP

41

20 A

Engine control system

42

43

44

45

46

47

48

49

50

EVPS

FAN1

30 A

40 A

60 A

30 A

40 A

Brake control system

Cooling fan

FAN2

―

ENG.MAIN

EPS

Engine control system

Power steering system

Rear window defogger

For protection of various circuits

―

DEFOG

IG2

INJECTOR

HEATER

Air conditioner

*Some models.

6-55

Maintenance and Care

Owner Maintenance

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

51

52

―

ENGINE4

20 A

Engine control system

Fuse block (Left side)

FUSE

RATING

DESCRIPTION

PROTECTED COMPONENT

*

1

2

RHT R

RHT L

30 A

―

Retractable hardtop (RH)

*

Retractable hardtop (LH)

3

―

4

ENGINE6

F.OUTLET

―

10 A

15 A

―

Engine control system

Accessory sockets

5

6

*

7

AT IND

7.5 A

30 A

15 A

30 A

―

AT shift indicator

8

MIRROR

R_DECK R

R_DECK L

F.WASHER

P.WINDOW

―

Power control mirror

*

9

Retractable hardtop (RH)

*

10

11

12

13

14

15

16

Retractable hardtop (LH)

Windshield washer

Power windows

―

SRS2/ESCL

SEAT WARM

M.DEF

15 A

20 A

7.5 A

Electronic steering lock

*

Seat warmer

*

Mirror defogger

*Some models.

6-56

Maintenance and Care

Appearance Care

Damage Caused by Bird Dropping,

Insects, or Tree Sap

Exterior Care

The paintwork on your Mazda represents

the latest technical developments in

composition and methods of application.

Occurrence

Bird droppings contain acids. If these are

not removed they can eat away the clear

and color base coat of the vehicle's

paintwork.

Environmental hazards, however, can

harm the paint's protective properties, if

proper care is not taken.

When insects stick to the paint surface and

decompose, corrosive compounds form.

These can erode the clear and color base

coat of the vehicle's paintwork if they are

not removed.

Here are some examples of possible

damage, with tips on how to prevent them.

Etching Caused by Acid Rain or

Industrial Fallout

Occurrence

Tree sap will harden and adhere

permanently to the paint finish. If you

scratch the sap off while it is hard, some

vehicle paint could come off with it.

Industrial pollutants and vehicle emissions

drift into the air and mix with rain or dew

to form acids. These acids can settle on a

vehicle's finish. As the water evaporates,

the acid becomes concentrated and can

damage the finish.

And the longer the acid remains on the

surface, the greater the chance is for

damage.

Prevention

It is necessary to have your Mazda washed

and waxed to preserve its finish according

to the instructions in this section. This

should be done as soon as possible.

Prevention

Bird droppings can be removed with a soft

sponge and water. If you are traveling and

these are not available, a moistened tissue

may also take care of the problem. The

cleaned area should be waxed according to

the instructions in this section.

Insects and tree sap are best removed with

a soft sponge and water or a commercially

available chemical cleaner.

It is necessary to wash and wax your

vehicle to preserve its finish according to

the instructions in this section. These steps

should be taken immediately after you

suspect that acid rain has settled on your

vehicle's finish.

Another method is to cover the affected

area with dampened newspaper for 1 to 2

hours. After removing the newspaper,

rinse off the loosened debris with water.

6-57

Maintenance and Care

Appearance Care



Water Marks

Occurrence

Chipped paint can lead to rust forming

on your Mazda. Before this happens,

repair the damage by using Mazda

touch-up paint according to the

instructions in this section. Failure to

repair the affected area could lead to

serious rusting and expensive repairs.

Rain, fog, dew, and even tap water can

contain harmful minerals such as salt and

lime. If moisture containing these minerals

settles on the vehicle and evaporates, the

minerals will concentrate and harden to

form white rings. The rings can damage

your vehicle's finish.

Follow all label and container directions

when using a chemical cleaner or polish.

Read all warnings and cautions.

Prevention

It is necessary to wash and wax your

vehicle to preserve its finish according to

the instructions in this section. These steps

should be taken immediately after you find

water marks on your vehicle's finish.

Maintaining the Finish

▼

Washing

CAUTION

Paint Chipping

Occurrence

When the wiper lever is in the AUTO

position and the ignition is switched ON,

the wipers may move automatically in

the following cases:

Paint chipping occurs when gravel thrown

in the air by another vehicle's tires hits

your vehicle.

If the windshield above the rain sensor

is touched or wiped with a cloth.

If the windshield is struck with a hand

or other object from either outside or

inside the vehicle.

How to avoid paint chipping

Keeping a safe distance between you and

the vehicle ahead reduces the chances of

having your paint chipped by flying

gravel.

Keep hands and scrapers clear of the

windshield when the wiper lever is in the

AUTO position and the ignition is

NOTE

switched ON as ꢀngers could be pinched

or the wipers and wiper blades damaged

when the wipers activate automatically.

If you are going to clean the windshield,

be sure the wipers are turned oꢂ



The paint chipping zone varies with the

speed of the vehicle. For example, when

traveling at 90 km/h (56 mph), the paint

chipping zone is 50 m (164 ft).



In low temperatures a vehicle's finish

completely (when it is most likely that the

engine is left running) this is particularly

important when clearing ice and snow.

hardens. This increases the chance of

paint chipping.

6-58

Maintenance and Care

Appearance Care

NOTE

Do not spray water in the engine

compartment. Otherwise, it could result

in engine-starting problems or damage

to electrical parts.



Mazda is not responsible for scratches

caused by automatic car washes or

improper washing.

Scratches are more noticeable on

vehicles with darker paint finishes.

When washing and waxing the vehicle,

be careful not to apply excessive force to

any single area of the vehicle hood.

Otherwise, you could dent the vehicle.

Do not use automatic car washing

machines and car washing devices using

high water pressure.



To minimize scratches on the vehicle's

paint finish:



Rinse off any dirt or other foreign matter

using lukewarm or cold water before

washing.

Use plenty of lukewarm or cold water

Make sure that the fuel-ꢀller lid is closed

and lock the doors. Otherwise, the

fuel-ꢀller lid may be forcefully opened by

water pressure causing damage to the

vehicle or fuel-ꢀller lid.



and a soft cloth when washing the

vehicle. Do not use a nylon cloth.

Rub gently when washing or drying the



vehicle.

To help protect the finish from rust and

deterioration, wash your Mazda

thoroughly and frequently, at least once a

month, with lukewarm or cold water.



Take your vehicle only to a car wash

that keeps its brushes well maintained.

Do not use abrasive cleansers or wax

that contain abrasives.



If the vehicle is washed improperly, the

paint surface could be scratched. Here are

some examples of how scratching could

occur.

CAUTION

Do not use steel wool, abrasive cleaners,

or strong detergents containing highly

alkaline or caustic agents on

Scratches occur on the paint surface when:

chrome-plated or anodized aluminum

parts. This may damage the protective

coating; also, cleaners and detergents

may discolor or deteriorate the paint.



The vehicle is washed without first

rinsing off dirt and other foreign matter.

The vehicle is washed with a rough, dry,

or dirty cloth.

The vehicle is washed at a car wash that

uses brushes that are dirty or too stiff.

Cleansers or wax containing abrasives

are used.



Pay special attention to removing salt, dirt,

mud, and other foreign material from the

underside of the fenders, and make sure

the drain holes in the lower edges of the

doors and rocker panels are clean.



6-59

Maintenance and Care

Appearance Care

Insects, tar, tree sap, bird droppings,

industrial fallout, and similar deposits can

damage the finish if not removed

immediately. When prompt washing with

plain water is ineffective, use a mild soap

made for use on vehicles.

Waxing

Your vehicle needs to be waxed when

water no longer beads on the finish.

Always wash and dry the vehicle before

waxing it. In addition to the vehicle body,

wax the metal trim to maintain its luster.

Thoroughly rinse off all soap with

lukewarm or cold water. Do not allow

soap to dry on the finish.

1. Use wax which contains no abrasives.

Wax containing abrasives will remove

paints and could damage bright metal

parts.

2. Use a good grade of natural wax for

metallic, mica, and solid colors.

3. When waxing, coat evenly with the

sponge supplied or a soft cloth.

4. Wipe off the wax with a soft cloth.

After washing the vehicle, dry it with a

clean chamois to prevent water spots from

forming.

WARNING

NOTE

Dry oꢂ brakes that have become wet by

driving slowly, releasing the accelerator

pedal and lightly applying the brakes

several times until the brake performance

returns to normal:

A spot remover to remove oil, tar, and

similar materials will usually also take off

the wax. Rewax these areas even if the rest

of the vehicle does not need it.

Driving with wet brakes is dangerous.

Increased stopping distance or the vehicle

pulling to one side when braking could

result in a serious accident. Light braking

will indicate whether the brakes have been

aꢂected.

Repairing Damage to the Finish

▼

Deep scratches or chips on the finish

should be repaired promptly. Exposed

metal quickly rusts and can lead to major

repairs.

CAUTION

If your Mazda is damaged and needs metal

parts repaired or replaced, make sure the

body shop applies anti-corrosion materials

to all parts, both repaired and new. This

will prevent them from rusting.

6-60

Maintenance and Care

Appearance Care

Bright-Metal Maintenance

Underbody Maintenance

▼



Use tar remover to remove road tar and

insects. Never do this with a knife or

similar tool.

To prevent corrosion on bright-metal

surfaces, apply wax or chrome

preservative and rub it to a high luster.

During cold weather or in coastal areas,

cover bright-metal parts with a coating

of wax or preservative heavier than

usual. It would also help to coat them

with noncorrosive petroleum jelly or

some other protective compound.

Road chemicals and salt used for ice and

snow removal and solvents used for dust

control may collect on the underbody. If

not removed, they will speed up rusting

and deterioration of such underbody parts

as fuel lines, frame, floor pan, and exhaust

system, even though these parts may be

coated with anti-corrosive material.



Thoroughly flush the underbody and

wheel housings with lukewarm or cold

water at the end of each winter. Try also to

do this every month.

CAUTION

Pay special attention to these areas

because they easily hide mud and dirt. It

will do more harm than good to wet

down the road grime without removing

it.

Do not use steel wool, abrasive cleaners, or

strong detergents containing highly

alkaline or caustic agents on

chrome-plated or anodized aluminum

parts. This may result in damage to the

protective coating and cause discoloration

or paint deterioration.

The lower edges of doors, rocker panels,

and frame members have drain holes that

should not be clogged. Water trapped there

will cause rusting.

WARNING

Dry oꢂ brakes that have become wet by

driving slowly, releasing the accelerator

pedal and lightly applying the brakes

several times until the brake performance

returns to normal:

Driving with wet brakes is dangerous.

Increased stopping distance or the vehicle

pulling to one side when braking could

result in a serious accident. Light braking

will indicate whether the brakes have been

aꢂected.

6-61

Maintenance and Care

Appearance Care

Aluminum Wheel Maintenance

Convertible Top (Soft Top)

Maintenance

▼

A protective coating is provided over the

aluminum wheels. Special care is needed

to protect this coating.

The convertible top is made of a special

high-grade material, but if it's not taken

good care of, hardening, staining, and loss

of luster will result. Maintain it under

these guidelines.

CAUTION

Do not use any detergent other than mild

detergent. Before using any detergent,

verify the ingredients. Otherwise, the

product could discolor or stain the

aluminum wheels.

Washing

Do not wait until the convertible top gets

really dirty before cleaning it. Dirt that's

there too long will cause deterioration.

1. Before washing, remove dust and

coarse particulate with a soft brush.

2. Gently clean the convertible top with a

synthetic neutral detergent, lots of

water, and a soft brush.

3. Rinse it thoroughly with clean water to

remove all the soap.

4. Wipe it as dry as you can before the

water dries on it.

NOTE



Do not use a wire brush or any abrasive

cleaner, polishing compound, or solvent

on aluminum wheels. They may damage

the coating.



Always use a sponge or soft cloth to

clean the wheels.

Rinse the wheels thoroughly with

lukewarm or cold water. Also, be sure to

clean the wheels after driving on dusty

or salted roads to help prevent

corrosion.

5. Then allow it to dry completely before

lowering it.

CAUTION

Automatic and high-pressure car washes

are harmful to a convertible top. Avoid

them.

Do not spray water directly on the area

where the window glass and the

convertible top meet. This would

probably cause water to enter the cabin.

6-62

Maintenance and Care

Appearance Care

Do not spray water directly on the seam

area of the body and the convertible top

as it could result in water penetrating the

cabin and trunk.

Drain filter cleaning procedure

Drain filterA

Drain filterB

Some leather treatment products can

ruin the convertible top's gloss. Be careful

of the one you choose.

Test on an inconspicuous, small corner of

the convertible top if you are not sure.

Do not wipe the convertible top using

alcohol, chlorine bleach, or organic

solvents such as thinner, benzene, or

gasoline. Otherwise, they may cause

discoloration or stains.

NOTE

If leaves or other matter block the drain

filter, water may enter the vehicle.

Clean the drain filter at least once a year.

Do not get any car wax on the

convertible top.

1. Check the position of the drain filter A

with your hand from behind the bow.

If you do, remove it with a good leather

cleaner or mild detergent (about 5%

solution).

Bow

Too much treatment on the convertible

top can be as damaging as too little.

Follow the manufacturer's directions.

Do not overdo it!

Let the convertible top dry completely

before lowering after applying treatment

or dressing.

Drain filterA

6-63

Maintenance and Care

Appearance Care

2. Remove the drain filter A while

pressing the tab.

Convertible Top (Retractable

Hardtop) Maintenance

▼

Washing

To help protect the retractable hardtop's

finish, use a soft cloth or sponge to wash

it.

Insects, tar, tree sap, bird droppings,

industrial fallout, and similar deposits can

damage the finish if they are not removed

immediately. When prompt washing with

plain water is ineffective use a mild soap

made for use on vehicles.

3. Remove drain filter B out of the

opening after removing drain filter A.

CAUTION

Do not use an automatic car wash.

Do not spray water directly on the area

where the window glass and the

retractable hardtop meet. This would

probably cause water to enter the cabin.

Do not use strong soap, chemical

detergents, or hot water, and do not

wash the retractable hardtop in direct

sunlight or when the surface is warm.

4. Remove foreign matter such as leaves

accumulated in drain filter A and drain

filter B.

Thoroughly rinse with lukewarm or cold

water. Do not allow soap to dry on the

finish.

5. Install in the reverse order of removal.

Waxing

CAUTION

Wax the retractable hardtop when water no

longer beads on the paint. Always wash

and dry it before waxing.

When installing the drain ꢀlter, make sure

that the drain ꢀlter is securely attached to

its designated position by pushing it until

the tab locks. Water may enter the vehicle if

the drain ꢀlter is not secured to its

designated position.

CAUTION

Wiping oꢂ dust or dirt with a dry cloth

will scratch the ꢀnish.

Do not use abrasive wax. This may

damage the protective coating and

discolor or deteriorate the paint.

6-64

Maintenance and Care

Appearance Care

NOTE

2. Remove your finger from the

A spot remover to remove oil, tar, and

similar materials will usually also take off

the wax. Rewax these areas.

retractable hardtop switch after the rear

roof is raised up.

3. Make sure the drainage outlets are

visible.

Drainage outlet cleaning procedure

There are drainage outlets on the left and

right of the lower side of the rear window.

Drainage

outlet

Rear roof

Rear window

Drainage

outlet

Rear roof links

4. Switch the ignition OFF.

WARNING

NOTE

If leaves or other foreign matter block the

drainage outlets, water may enter the

cabin. Clean the drainage outlets at least

once every 6 months.

Verify that the ignition is switched oꢂ:

Closing the roof with the ignition not

switched oꢂ is dangerous as the motors

could turn on suddenly and cause

injury resulting from hands or ꢀngers

being pinched in the mechanism.

5. Remove leaves and other foreign

matter accumulated in the drainage

outlet.

1. Continue pressing the retractable

hardtop switch in the open direction

until the rear roof is raised up from the

fully closed position.

Refer to Opening the Roof on page

3-44.

6-65

Maintenance and Care

Appearance Care

7. Pour about 200 ml (200 cc) of water at

once into each of the left and right

drainage outlets to wash away small

particles of foreign matter inside the

drainage path.

CAUTION

When cleaning the drainage outlets, be

careful not to touch the roof links or the

framework of the rear roof. Otherwise,

you could get injured.

Rear roof

Roof links

CAUTION

6. After cleaning the drainage outlets,

continuously press the retractable

hardtop switch in the close direction to

close the rear roof.

Use washer ꢁuid instead of water in

cold weather.

If water is used, the water may freeze

inside the drainage path blocking the

path.

Refer to Closing the Roof on page

3-44.

6-66

Maintenance and Care

Appearance Care

Plastic Part Maintenance

▼

Interior Care



When cleaning the plastic lenses of the

lights, do not use gasoline, kerosene,

rectified spirit, paint, thinner, highly

acidic detergents, or strongly alkaline

detergents. Otherwise, these chemical

agents can discolor or damage the

surfaces resulting in a significant loss in

functionality. If plastic parts become

inadvertently exposed to any of these

chemical agents, flush with water

immediately.

If plastic parts such as the bumpers

become inadvertently exposed to

chemical agents or fluids such as

gasoline, oil, engine coolant, or battery

fluid, it could cause discoloration,

staining, or paint peeling. Wipe off any

such chemical agents or fluids using a

soft cloth immediately.

High water temperature and high water

pressure car washers are available

depending on the type of high pressure

car washer device. If the car washer

nozzle is put too close to the vehicle or

aimed at one area for an extended period

of time, it could deform plastic parts or

damage the paint.

WARNING

Do not spray water into the vehicle cabin:

Spraying water into the vehicle cabin is

dangerous as electrical devices such as the

audio and switches could get wet resulting

in a malfunction or vehicle ꢀre.

NOTE



Do not wipe the interior using alcohol,

chlorine bleach, or organic solvents

such as thinner, benzene, and gasoline.

Otherwise, it may cause discoloration or

stains.

Rubbing hard with a stiff brush or cloth

may cause damage.



If the vehicle interior becomes soiled by

any of the following, wipe it off

immediately using a soft cloth.

Leaving it uncleaned could cause

discoloration, stains, cracks, or peeling of

the coating, and it will make it hard to

wipe off later.



Beverage or fragrance

Grease or oil

Soiling



Do not use wax containing compounds

(polish). Otherwise, it could result in

paint damage.

In addition, do not use an electrical or

air tool to apply wax. Otherwise, the

frictional heat generated could result in

deformation of plastic parts or paint

damage.



Seat Belt Maintenance

▼

1. Clean the soiled area by lightly

dabbing it with a soft cloth soaked in a

mild detergent (approx. 5%) diluted

with water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

6-67

Maintenance and Care

Appearance Care

3. Before retracting seat belts which have

been pulled out for cleaning, dry them

off thoroughly and make sure there is

no remaining moisture on them.

Upholstery and Synthetic Leather

Maintenance

▼

Fabric

1. Clean the soiled area by lightly

dabbing it with a soft cloth soaked in a

mild detergent (approx. 5%) diluted

with water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

WARNING

If a seat belt appears frayed or has

abrasions, have it replaced by an

Authorized Mazda Dealer:

If a seat belt is used under such a condition,

it cannot function at its full capacity which

could result in serious injury or death.

Synthetic leather

1. Remove dust and sand using a vacuum

cleaner.

2. Wipe the soiled area with a soft cloth

soaked in a mild detergent (approx.

5%) diluted with water.

3. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

Use a mild detergent to remove soiling

from a seat belt:

If organic solvents are used for cleaning the

seat belts or they become stained or

bleached, there is the possibility of them

becoming weakened and as a result, they

may not function at their full capacity

which could cause serious injury or death.

Leather Upholstery Maintenance^*

▼

1. Remove dust and sand using a vacuum

cleaner.

NOTE

Clean seat belts diligently if they get dirty.

Leaving them uncleaned will make it

difficult to clean them later, and it may

affect the smooth retracting of the seat

belt.

2. Wipe off the soiled area with a soft

cloth and a suitable, special cleaner or

a soft cloth soaked in a mild detergent

(about 5%) diluted with water.

3. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

4. Remove moisture with a dry, soft cloth

and allow the leather to further dry in a

well-ventilated, shaded area. If the

leather gets wet such as from rain,

remove the moisture and dry it as soon

as possible.

Vinyl Upholstery Maintenance

▼

Remove dust and dirt from the vinyl

upholstery using a brush or vacuum.

Remove soiling from vinyl upholstery

using a leather and vinyl upholstery

cleaner.

*Some models.

6-68

Maintenance and Care

Appearance Care

NOTE

Plastic Part Maintenance

▼



Because genuine leather is a natural

material, its surface is not uniform and

it may have natural scars, scratches,

and wrinkles.

To maintain the quality for as long as

possible, periodical maintenance, about

twice a year, is recommended.

If the leather upholstery comes into

contact with any of the following, clean

it immediately.

CAUTION

Do not use polishing agents.



Depending on the product ingredients,

they could cause discoloration, stains,

cracks or peeling of the coating.

Instrument Panel Top Maintenance

▼

1. Wipe the soiled area with a soft cloth

soaked in a mild detergent (approx.

5%) diluted with water.

Leaving it uncleaned could cause

premature wear, mold, or stains.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.



Sand or dirt

Grease or oil, such as hand cream

Alcohol, such as in cosmetic or hair



dressing items

Panel Maintenance

▼



If the leather upholstery gets wet,

promptly remove moisture with a dry

cloth. Remaining moisture on the

surface may cause deterioration such as

hardening and shrinkage.

Exposure to direct sunlight for long

periods may cause deterioration and

shrinkage. When parking the car under

direct sunlight for long periods, shade

the interior using sunshades.

Do not leave vinyl products on the

leather upholstery for long periods.

They may affect the leather quality and

coloring. If the cabin temperature

becomes hot, the vinyl may deteriorate

and adhere to the genuine leather.

If a panel becomes soiled, wipe it off with

a soft cloth soaked in clean water and

thoroughly wrung out.

If some areas require further cleaning, use

the following procedure:

1. Wipe the soiled area with a soft cloth

soaked in a mild detergent (approx.

5 %) diluted with water.

2. Wipe off the remaining detergent using

a cloth soaked in clean water and

wrung out well.

NOTE

Be particularly careful when cleaning

shiny surface panels and metallic parts

such as plating as they can be scratched

easily.

6-69

Maintenance and Care

Appearance Care

Cleaning the Window Interiors

▼

If the windows become covered with an

oily, greasy, or waxy film, clean them with

glass cleaner. Follow the directions on the

container.

CAUTION

Do not scrape or scratch the inside of the

window glass. It could damage the

thermal ꢀlaments.

When washing the inside of the window

glass, use a soft cloth dampened in

lukewarm water, gently wiping the

thermal ꢀlaments.

Use of glass cleaning products could

damage the thermal ꢀlaments.

Cleaning the Floor Mats

▼

Rubber floor mats should be cleaned with

mild soap and water only.

WARNING

Do not use rubber cleaners, such as tire

cleaner or tire shine, when cleaning rubber

ꢃoor mats:

Cleaning the rubber ꢁoor mats with rubber

cleaning products makes the ꢁoor mats

slippery.

This may cause an accident when

depressing the accelerator, brake, or clutch

(Manual transmission) pedal or when

getting in or out of the vehicle.

After removing the floor mats for

cleaning, always reinstall them securely

(page 3-52).

6-70

Maintenance and Care for Your Mazda Mx-5 SUV Fourth Generation (2016-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals