2016-2026 Mazda Mx-5 SUV Maintenance and Care -> Wiper Blades User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and Care -> Wiper Blades for Your Mazda Mx-5 SUV Fourth Generation (2016-2026)

Maintenance and Care  
Owner Maintenance  
Body Lubrication  
Wiper Blades  
All moving points of the body, such as  
door and hood hinges and locks, should be  
lubricated each time the engine oil is  
changed. Use a nonfreezing lubricant on  
locks during cold weather.  
CAUTION  
Hot waxes applied by automatic car  
washers have been known to aꢀect the  
wiper's ability to clean windows.  
To prevent damage to the wiper blades,  
do not use gasoline, kerosene, paint  
thinner, or other solvents on or near  
them.  
Make sure the hood's secondary latch  
keeps the hood from opening when the  
primary latch is released.  
When the wiper lever is in the AUTO  
position and the ignition is switched ON,  
the wipers may move automatically in  
the following cases:  
If the windshield above the rain sensor  
is touched.  
If the windshield above the rain sensor  
is wiped with a cloth.  
If the windshield is struck with a hand  
or other object.  
If the rain sensor is struck with a hand  
or other object from inside the vehicle.  
Be careful not to pinch hands or ꢁngers  
as it may cause injury, or damage the  
wipers. When washing or servicing the  
vehicle, make sure the wiper lever is in  
the OFF position.  
Contamination of either the windshield or  
the blades with foreign matter can reduce  
wiper effectiveness. Common sources are  
insects, tree sap, and hot wax treatments  
used by some commercial car washes.  
If the blades are not wiping properly, clean  
the window and blades with a good  
cleaner or mild detergent; then rinse  
thoroughly with clean water. Repeat if  
necessary.  
6-28  
Maintenance and Care  
Owner Maintenance  
3. Tilt the blade assembly and remove it  
from the arm.  
Replacing Windshield Wiper Blades  
When the wipers no longer clean well, the  
blades are probably worn or cracked.  
Replace them.  
CAUTION  
To prevent damage to the wiper arms and  
other components, do not try to sweep the  
wiper arm by hand.  
NOTE  
When raising both windshield wiper arms,  
raise the driver's side wiper arm first.  
When lowering the wiper arms, slowly  
lower the wiper arm from the passenger's  
side first while supporting it with your  
hand. Forcefully lowering the wiper arms  
could damage the wiper arm and blade,  
and may scratch or crack the windshield.  
CAUTION  
To prevent damage to the windshield  
let the wiper arm down easily, do not  
let it slap down on the windshield.  
4. Pull down the blade rubber and slide it  
out of blade holder.  
Replace the wiper blades using the  
following procedure.  
(Type A)  
1. Raise the wiper arm.  
2. Open the clip and slide the blade  
assembly in the direction of the arrow.  
5. Remove the metal stiffeners from each  
blade rubber and install them in the  
new blade.  
6-29  
Maintenance and Care  
Owner Maintenance  
CAUTION  
CAUTION  
To prevent damage to the windshield  
let the wiper arm down easily, do not  
let it slap down on the windshield.  
2. Hold the end of the rubber and pull  
until the tabs are free of the metal  
support.  
Do not bend or discard the stiꢀeners.  
You need to use them again.  
If the metal stiꢀeners are switched,  
the blade's wiping eꢂciency could be  
reduced.  
So do not use the driver's side metal  
stiꢀeners on the passenger's side, or  
vice versa.  
Metal support  
Be sure to reinstall the metal  
stiꢀeners in the new blade rubber so  
that the curve is the same as it was in  
the old blade rubber.  
Tab  
6. Carefully insert the new blade rubber.  
Then install the blade assembly in the  
reverse order of removal.  
3. Remove the metal stiffeners from each  
blade rubber and install them in the  
new blade.  
(Type B)  
1. Raise the wiper arm and turn the blade  
assembly to expose the plastic locking  
clip.  
Compress the clip and slide the  
assembly downward; then lift it off the  
arm.  
Plastic locking clip  
6-30  
Maintenance and Care  
Owner Maintenance  
CAUTION  
Do not bend or discard the stiꢀeners.  
You need to use them again.  
If the metal stiꢀeners are switched,  
the blade's wiping eꢂciency could be  
reduced.  
So do not use the driver's side metal  
stiꢀeners on the passenger's side, or  
vice versa.  
Be sure to reinstall the metal  
stiꢀeners in the new blade rubber so  
that the curve is the same as it was in  
the old blade rubber.  
4. Carefully insert the new blade rubber.  
Then install the blade assembly in the  
reverse order of removal.  
NOTE  
Install the blade so that the tabs are  
toward the bottom of the wiper arm.  
6-31  

Related Topics

Popular Owner Manuals