Get MOBILITY Guide for Mini Clubman SUV Second Generation (2015-2024)

MOBILITY

Refueling

Vehicle features and options

Fuel cap

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

Opening

1. To open the fuel filler flap, press on

the rear edge, arrow. The fuel filler flap

opens.

General information

Follow the fuel recommendation, refer to

page 250, prior to refueling.

2. Turn the fuel cap counterclockwise.

Safety information

NOTICE

With a range below 30 miles/50 km,

the engine may no longer have sufficient

fuel. Engine functions are not ensured

anymore. There is a risk of damage to

property. Refuel promptly.

3. Place the fuel cap in the bracket at-

tached to the fuel filler flap.

248

Online Edition for Part no. 01405A7B0F2 - II/23

Refueling

MOBILITY

Closing

Safety information

Warning

NOTICE

The retaining strap of the fuel cap can be

jammed and crushed during closing. The

cap cannot be correctly closed. Fuel or fuel

vapors can escape. There is a risk of injury

or risk of damage to property. Pay atten-

tion that the retaining strap is not jammed

or crushed when closing the cap.

Fuels are toxic and aggressive. Overfilling

of the fuel tank can damage the fuel sys-

tem. Painted surfaces may be damaged by

contact with fuel. Escaping fuel can harm

the environment. There is a risk of damage

to property. Avoid overfilling.

1. Fit the cap and turn it clockwise until

you clearly hear a click.

2. Press on the fuel filler flap until it en-

gages.

Emergency unlocking

It may be necessary in certain situations

to unlock the fuel filler flap manually, for

instance with an electrical malfunction.

Have the fuel filler flap unlocked by an au-

thorized service center or another qualified

service center or repair shop.

Follow the following when re-

fueling

General information

When refueling, hook the filler nozzle com-

pletely into the filler pipe. Lifting up the

filler nozzle during refueling causes:

–

Premature switching off.

Reduced return of the fuel vapors.

The fuel tank is full when the filler nozzle

clicks off the first time.

Make sure that the fuel cap is closed prop-

erly after refueling, otherwise the emissions

warning light may illuminate.

Follow safety regulations posted at the fill-

ing station.

249

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Fuel

Safety information

NOTICE

Vehicle features and options

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

Even small quantities of the wrong fuel or

wrong fuel additives can damage the fuel

system and engine. Furthermore, the cat-

alytic converter is permanently damaged.

There is a risk of damage to property. Do

not refuel or add the following in the case

of gasoline engines:

–

Leaded gasoline.

Metallic additives, for instance man-

ganese or iron.

Do not press the Start/Stop button after

refueling with the wrong fuel. Contact an

authorized service center or another quali-

fied service center or repair shop.

Fuel recommendation

General information

Depending on the region, many filling sta-

tions sell fuel that has been customized to

winter or summer conditions. Fuel that is

available in winter, for instance helps make

a cold start easier.

NOTICE

Incorrect fuels can damage the fuel system

and the engine. There is a risk of damage

to property. Do not use fuels with a higher

ethanol content than recommended. Do

not refuel with fuels containing methanol,

e.g. M5 to M100.

Gasoline

General information

For the best fuel efficiency, the gasoline

should be sulfur-free or very low in sulfur

content.

NOTICE

Fuels that are marked on the gas pump as

containing metal must not be used.

Fuel that does not comply with the mini-

mum quality can compromise engine func-

tion or cause engine damage. There is a

risk of damage to property. Do not fill with

fuel that does not comply with the mini-

mum quality.

You can fill up using fuel with a maximum

ethanol content of 10 %; e.g., E10.

To achieve nominal values for mileage and

consumption, follow the specified fuel qual-

ity in the sales literature.

The use of fuels of minimum quality has no

influence on the service life of the engine.

250

Online Edition for Part no. 01405A7B0F2 - II/23

Fuel

MOBILITY

Caution

The use of poor-quality fuels may result

in harmful engine deposits or damage.

Additionally, problems relating to drivabil-

ity, starting and stalling, especially under

certain environmental conditions such as

high ambient temperature and high alti-

tude, may occur.

If drivability problems are encountered,

we recommend switching to a high quality

gasoline brand and a higher octane grade

— AKI number — for a few tank fills. To

avoid harmful engine deposits, it is highly

recommended to purchase gasoline from

Top Tier retailers.

Failure to comply with these recommenda-

tions may result in the need for additional

maintenance.

Recommended gas quality

MINI recommends AKI 91.

John Cooper Works:

MINI recommends AKI 93.

Minimum fuel grade

MINI recommends AKI 87.

John Cooper Works:

MINI recommends AKI 91.

If you use gasoline with this minimum AKI

Rating, the engine may produce knocking

sounds when starting at high external tem-

peratures. This has no effect on the engine

life.

251

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

Tire pressure specifications

Vehicle features and options

In the tire inflation pressure table

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

The tire inflation pressure table, refer to

page 253, contains all tire inflation pres-

sure specifications for the specified tire

sizes at the ambient temperature. The tire

inflation pressure values apply to tire sizes

approved by the manufacturer of the vehicle

for the vehicle type.

To identify the correct tire inflation pres-

sure, please note the following:

–

Tire sizes of the vehicle.

Maximum speed for driving.

Tire pressure

Checking the tire pressure

General information

Tires heat up while driving. The tire pres-

sure increases with the tire temperature.

General information

The tire condition and tire pressure influ-

ence the following:

–

The service life of the tires.

Driving safety.

Tires have a natural, consistent tire pres-

sure loss.

Driving comfort.

The displays of inflation devices may under-

read by up to 0.1 bar/2 psi.

Fuel consumption.

Safety information

Checking using tire inflation pressure

specifications in the tire inflation

pressure table

Warning

A tire with too little or no tire inflation

pressure may heat up significantly and

sustain damage. This will have a negative

impact on aspects of handling, such as

steering and braking response. There is

a risk of accident. Regularly check the

tire inflation pressure, and correct it as

needed, for instance twice a month and

before a long trip.

The tire inflation pressure specifications in

the tire inflation pressure table only relate

to cold tires or tires at the same tempera-

ture as the ambient temperature.

Only check the tire inflation pressure levels

when the tires are cold, i.e.:

–

Distance travelled of max.

1.25 miles/2 km has not been ex-

ceeded.

–

If the vehicle has not moved again for at

least 2 hours after a trip.

252

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

Do not exceed a speed of 100 mph/

160 km/h.

1. Determine the intended tire inflation

pressure levels for the mounted tires.

2. Check the tire inflation pressure in all

four tires, using a pressure gage, for ex-

ample.

Tire pressure values up to

100 mph/160 km/h

3. Correct the tire inflation pressure if the

actual tire inflation pressure deviates

from the intended tire inflation pres-

sure.

COOPER ALL4

Tire size

Pressure specifica-

tions in bar/PSI

4. Check whether all valve caps are

screwed onto the tire valves.

Specifications

in bar/PSI with

cold tires

After correcting the tire pressure

For flat tire monitor: reinitialize flat tire

monitor.

205/55 R 16 91 2.2 / 32

V A/S

2.2 / 32

For Tire Pressure Monitor: reset the Tire

Pressure Monitor.

225/45 R 17 91

V A/S

Checking the tire inflation pressure of

the emergency wheel

205/55 R 16 91

W

Also check the tire inflation pressure of

the emergency wheel in the cargo area reg-

ularly, and correct it as needed.

205/55 R 16 91

H M+S

225/45 R 17 91

H M+S

Tire pressures up to 100 mph/

160 km/h

For speeds of up to 100 mph/160 km/h

and for optimum driving comfort, note the

pressure values in the tire pressure table,

refer to page 253, and adjust as necessary.

225/45 R 17 94 2.4 / 35

Y XL

2.4 / 35

225/40 R 18 92

Y XL

225/40 R 18 92

H XL A/S

195/60 R 16 89

H M+S

195/55 R 17 92

H XL M+S

225/40 R 18 92

V XL M+S

These pressure values can also be found on

the tire pressure label on the driver's door

pillar.

253

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

Tire size

Pressure specifica-

tions in bar/PSI

Tire size

Pressure specifications

in bar/PSI

235/35 R 19 91 2.6 / 38

Y XL

2.6 / 38

205/45 R 18

90 H XL M+S

2.7 / 39

205/45 R 18 90

H XL M+S

Emergency

wheel

Speed up to a max. of

50 mph / 80 km/h

Emergency

wheel

Speed up to a max. of

50 mph / 80 km/h

T 125/70 R 17 4.2 / 60

98 M

T 125/70 R 17

98 M

4.2 / 60

JOHN COOPER WORKS

Tire size

Pressure specifications

in bar/PSI

COOPER S, COOPER S ALL4

Tire size

Pressure specifications

in bar/PSI

Specifications

in bar/PSI with

cold tires

Specifications

in bar/PSI with

cold tires

225/40 R 18

92 H XL A/S

2.6 / 38

225/45 R 17

91 V A/S

2.4 / 35

2.6 / 38

225/40 R 18

92 Y XL

225/45 R 17

94 Y XL

235/35 R 19

91 Y XL

225/45 R 17

91 H M+S

225/40 R 18

92 V XL M+S

225/40 R 18

92 H XL A/S

2.6 / 38

205/45 R 18

90 H XL M+S

2.7 / 39

225/40 R 18

92 Y XL

Tire inflation pressures at

maximum speeds above 100 mph/

160 km/h

235/35 R 19

91 Y XL

195/55 R 17

92 H XL M+S

Warning

225/40 R 18

92 V XL M+S

In order to drive at maximum speeds in

excess of 100 mph/160 km/h, please ob-

serve and, if necessary, adjust tire pres-

sures for speeds exceeding 100 mph/

160 km/h from the relevant table on the

254

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

Tire size

MOBILITY

following pages. Otherwise, tire damage

and accidents could occur.

Pressure specifica-

tions in bar/PSI

225/40 R 18 92 2.8 / 41

H XL A/S

2.8 / 41

For speeds over 100 mph/160 km/h and

for optimum driving comfort, note the pres-

sure values in the tire pressure table, refer

to page 255, and adjust as necessary.

195/60 R 16 89

H M+S

195/55 R 17 92

H XL M+S

Tire pressure values over 100 mph/

160 km/h

225/40 R 18 92

V XL M+S

COOPER ALL4

235/35 R 19 91

Y XL

Tire size

Pressure specifica-

tions in bar/PSI

205/45 R 18 90

H XL M+S

Specifications

in bar/PSI with

cold tires

Emergency

wheel

Speed up to a max. of

50 mph / 80 km/h

T 125/70 R 17

98 M

4.2 / 60

205/55 R 16 91 2.4 / 35

V A/S

2.4 / 35

225/45 R 17 91

V A/S

205/55 R 16 91

W

205/55 R 16 91

H M+S

225/45 R 17 91

H M+S

225/45 R 17 94

Y XL

225/40 R 18 92

Y XL

255

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

COOPER S, COOPER S ALL4

JOHN COOPER WORKS

Tire size

Pressure specifications

in bar/PSI

Tire size

Pressure specifications

in bar/PSI

Specifications

in bar/PSI with

cold tires

Specifications

in bar/PSI

with cold tires

225/45 R 17

91 V A/S

2.8 / 41

225/40 R 18

92 H XL A/S

2.8 / 41

225/45 R 17

94 Y XL

225/40 R 18

92 Y XL

225/45 R 17

91 H M+S

235/35 R 19

91 Y XL

225/40 R 18

92 H XL A/S

225/40 R 18

92 V XL M+S

3.2 / 46

3.0 / 44

3.2 / 46

3.0 / 44

225/40 R 18

92 Y XL

205/45 R 18

90 H XL M+S

235/35 R 19

91 Y XL

195/55 R 17

92 H XL M+S

Tire marking

225/40 R 18

92 V XL M+S

3.2 / 46

3.0 / 44

3.2 / 46

3.0 / 44

Tire size

205/45 R 17 84 V

205/45 R 18

90 H XL M+S

205: nominal width in mm

45: cross-sectional relationship in %

R: radial tire code

Emergency

wheel

Speed up to a max. of

50 mph / 80 km/h

17: rim diameter in inches

84: load bearing capacity

V: speed code letter

T 125/70 R 17 4.2 / 60

98 M

ZR tires: reinforced radial tire for speeds

exceeding 150 mph/240 km/h

Maximum tire load

Maximum tire load is the maximum permis-

sible weight for which the tire is approved.

Locate the maximum tire load on the tire

sidewall and the Gross Axle Weight Rating

– GAWR – on the certification label on the

256

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

driver’s door pillar. Divide the tire load by

1.1. It must be greater than one-half of

the vehicle’s Gross Axle Weight Rating –

GAWR. Note, front vs. rear GAWR and tire

loads, respectively.

Uniform Tire Quality Grading

Quality grades can be found where appli-

cable on the tire sidewall between tread

shoulder and maximum section width.

E.g.: Treadwear 200; Traction AA; Tempera-

ture A

Speed letter

DOT Quality Grades

Treadwear

Designation Maximum speed

Q

R

S

up to 100 mph/160 km/h

up to 106 mph/170 km/h

up to 112 mph/180 km/h

up to 118 mph/190 km/h

up to 131 mph/210 km/h

up to 150 mph/240 km/h

up to 167 mph/270 km/h

up to 186 mph/300 km/h

Traction AA A B C

Temperature A B C

All passenger vehicle tires must conform to

Federal Safety Requirements in addition to

these grades.

T

H

V

W

Y

Treadwear

The treadwear grade is a comparative rat-

ing based on the wear rate of the tire

when tested under controlled conditions on

a specified government test course. E.g., a

tire graded 150 would wear one and one-

half, 1 g, times as well on the government

course as a tire graded 100. The relative

performance of tires depends upon the ac-

tual conditions of their use, however, and

may depart significantly from the norm due

to variations in driving habits, service prac-

tices and differences in road characteristics

and climate.

Tire Identification Number

DOT code: DOT xxxx xxx 0123

xxxx: manufacturer code for the tire brand

xxx: tire size and tire design

0123: tire age

Tires with DOT codes meet the guidelines

of the U.S. Department of Transportation.

Tire age

Traction

The traction grades, from highest to lowest,

are AA, A, B, and C.

Recommendation

Regardless of the tire tread depth, replace

tires at least every 6 years.

Those grades represent the tire's ability to

stop on wet pavement as measured under

controlled conditions on specified govern-

ment test surfaces of asphalt and concrete.

A tire marked C may have poor traction per-

formance.

Manufacture date

You can find the manufacture date of the

tire on the tire sidewall.

The traction grade assigned to this tire is

based on straight-ahead braking traction

tests, and does not include acceleration,

Designation

Manufacture date

DOT … 0123

1st week of 2023

257

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

cornering, hydroplaning, or peak traction

characteristics.

Tire tread

Summer tires

Temperature

Do not drive with a tire tread depth of less

than 0.12 in/3 mm, otherwise there is an

increased risk of aquaplaning.

The temperature grades are A, the highest,

B, and C, representing the tire's resistance

to the generation of heat and its ability

to dissipate heat when tested under control-

led conditions on a specified indoor labo-

ratory test wheel. Sustained high tempera-

ture can cause the material of the tire to

degenerate and reduce tire life, and exces-

sive temperature can lead to sudden tire

failure. The grade C corresponds to a level

of performance which all passenger car tires

must meet under the Federal Motor Vehicle

Safety Standard No. 109. Grades Band A

represent higher levels of performance on

the laboratory test wheel than the minimum

required by law.

Winter tires

Do not drive with a tire tread depth of less

than 0.16 in/4 mm, as such tires are less

suitable for winter driving conditions.

All-season tires

Do not drive with a tire tread depth of less

than 0.16 in/4 mm, as such tires are less

suitable for winter driving conditions.

Minimum tread depth

Warning

The temperature grade for this tire is es-

tablished for a tire that is properly inflated

and not overloaded. Excessive speed, un-

derinflation, or excessive loading, either

separately or in combination, can cause

heat buildup and possible tire failure.

Distributed over the tire circumference are

the tire manufacturer’s wear indicators with

a height of at least 0.06 in/1.6 mm, which

serve as an indicator of tire tread wear.

Runflat tires

Runflat tires, refer to page 261, are labeled

with a circular icon containing the letters

RSC marked on the tire sidewall.

The positions of the wear indicators are

marked on the tire sidewall with TWI, Tread

Wear Indicator.

M+S

Winter and all-season tires with better cold

weather performance than summer tires.

Irrespective of the wear indicators, observe

the statutory regulations on the minimum

tread depth.

258

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

or another qualified service center or re-

pair shop. Have vehicle towed or trans-

ported as needed. Do not repair damaged

tires, but have them replaced.

Tire damage

General information

Check your tires regularly for damage, for-

eign bodies lodged in the tread, and tread

wear.

Warning

Driving over rough or damaged road surfa-

ces, as well as debris, curbs and other obsta-

cles can cause serious damage to wheels,

tires and suspension parts. This is more

likely to occur with low-profile tires, which

provide less cushioning between the wheel

and the road. Be careful to avoid road haz-

ards and reduce your speed, especially if the

vehicle is equipped with low-profile tires.

Tires can become damaged by driving over

obstacles, e.g., curbs or road damage, at

high speed. Larger wheels have a smaller

tire cross-section. The smaller the tire

cross-section, the higher the risk of tire

damage. There may be a risk of accidents

and risk of damage to property. If possible,

avoid driving over objects or road condi-

tions that may damage tires, or drive over

them slowly and carefully.

Indications of tire damage or other vehicle

malfunctions:

–

Unusual vibrations.

Unusual tire or running noises.

Exchanging wheels and tires

Unusual handling such as a strong ten-

dency to pull to the left or right.

Mounting and wheel balancing

–

Uneven wear pattern, e.g., increased

wear in the area of the tire shoulder.

Have wheels and tires mounted and bal-

anced by an authorized service center or

another qualified service center or repair

shop.

Damage can be caused by the following sit-

uations, for instance:

–

Driving over curbs.

Road damage.

Approved wheels and tires

General information

Only certain wheel/tire combinations are

suitable depending on vehicle and equip-

ment. The vehicle manufacturer determines

wheel/tire combinations on the basis of the

following criteria:

Tire pressure too low.

Vehicle overloading.

Incorrect tire storage.

Safety information

Warning

–

Tire size, e.g., tire width, aspect ratio.

Wheel size, e.g., rim diameter, offset.

Damaged tires can lose tire inflation pres-

sure, which can lead to loss of vehicle

control. There is a risk of accident. If

tire damage is suspected while driving,

immediately reduce speed and stop. Have

wheels and tires checked. To do so, drive

carefully to an authorized service center

Ask an authorized service center or another

qualified service center or repair shop about

wheels and tires that are suitable for the

vehicle as well as special equipment.

259

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

wheels and tires, the vehicle manufacturer

Safety information

Warning

recommends using star-marked tires again.

The vehicle manufacturer recommends that

you use tires of the same make and tread

design.

Wheels and tires that are not suitable for

the vehicle can damage parts of the vehi-

cle. There is a risk of accident. The vehicle

manufacturer recommends that you use

only wheels and tires that have been ap-

proved as suitable for the vehicle type.

New tires

Tire traction is not optimal due to manufac-

turing circumstances when tires are brand

new.

Drive conservatively for the first

200 miles/300 km.

Warning

Unsuitable wheel/tire combinations will

impair vehicle handling and a number of

system functions, such as the Antilock

Braking System or Dynamic Stability Con-

trol. There is a risk of accident. The ve-

hicle manufacturer recommends that you

use only wheels and tires that have been

approved as suitable for the vehicle type.

Following tire damage, have the original

wheel/tire combination remounted on the

vehicle as soon as possible.

Retreaded tires

Warning

Retreated tires can have different tire cas-

ing structures. With advanced age the

service life can be limited. There is a risk

of accident. The manufacturer of the ve-

hicle does not recommend the use of re-

treaded tires.

Winter tires

Recommended tire brands

Winter tires are recommended for operat-

ing on winter roads.

Tire types are developed for each vehicle

and optimized specifically for the individual

requirements of that vehicle, e.g.:

Winter tires can be identified by the icon

with mountain and snowflake, as well as the

M+S marking on the tire sidewall.

–

Handling.

Comfort.

All-season tires with the M+S designation,

but without icon with mountain and snow-

flake, have better winter characteristics

Noise characteristics.

Specially developed tires are marked with

a star on the tire sidewall. After replacing

260

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

than summer tires but generally do not ach-

ieve the performance of winter tires.

Always protect tires against all contact with

oil, grease, and solvents.

Do not leave tires in plastic bags.

Remove dirt from wheels or tires.

Maximum speed of winter tires

If the maximum speed of the vehicle is

higher than the permissible speed for the

winter tires, then attach a sign showing the

permissible maximum speed in the field of

vision. The info label is available from an

authorized service center or another quali-

fied service center or repair shop.

Runflat tires

Principle

Runflat tires permit continued driving un-

der limited conditions even in the event of a

complete tire pressure loss.

With winter tires mounted, observe and do

not exceed the permissible maximum speed.

General information

Changing runflat tires

The wheels are composed of tires that are

self-supporting to a limited degree.

When changing from runflat tires to stand-

ard tires, it must be ensured that the vehicle

contains an emergency wheel or tire mobi-

lity kit. For more information, contact an

authorized service center or another quali-

fied service center or repair shop.

The reinforcement of the sidewall allows

the tire to remain drivable to a limited de-

gree in the event of a tire pressure loss.

Follow the instructions for continued driv-

ing with a flat tire.

Wheel change between axles

Different abrasion patterns can occur on the

front and rear axles depending on individual

driving conditions. The tires can be rotated

in pairs between the axles to achieve even

abrasion. For more information, contact an

authorized service center or another quali-

fied service center or repair shop. After

changing, check the tire pressure and cor-

rect, if needed.

Safety information

Warning

The vehicle handles differently when a

runflat tire has insufficient or no tire pres-

sure; for instance, reduced directional sta-

bility when braking, braking distances are

longer and the self-steering properties will

change. There is a risk of accident. Drive

moderately and do not exceed a speed of

50 mph/80 km/h.

Storing tires

Tire pressure

Do not exceed the maximum tire inflation

pressure indicated on the tire sidewall.

Storage

Store wheels and tires in a cool, dry and

dark place.

261

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

Identification

General information

–

The filled in tire sealant closes the dam-

age from the inside when it hardens.

–

Follow the instructions on using the tire

repair set found on the compressor and

sealant bottle.

–

The use of a tire repair set can be in-

effective if the tire puncture measures

above approx. 0.16 in/4 mm.

Do not remove foreign objects that have

penetrated the tire. Remove foreign ob-

jects only when they are visibly protrud-

ing from the tire.

Runflat tires are labeled with a circular icon

containing the letters RSC marked on the

tire sidewall.

–

The compressor can be used to check

the tire inflation pressure.

Repairing a flat tire

Overview

Storage

Depending on the equipment, storage for

the tire repair set is provided as follows:

Safety precautions

–

Park the vehicle as far away as possible

from passing traffic and on solid ground.

–

Turn on the hazard warning system.

–

In the cargo area under the cargo floor

panel.

Secure the vehicle against rolling away

by setting the parking brake.

In the cargo area on the left or right

side.

–

Turn the steering wheel until the front

wheels are in the straight-ahead posi-

tion and engage the steering wheel lock.

In the cargo area behind a side trim

panel.

Have all vehicle occupants get out of the

vehicle and ensure that they remain out-

side the hazardous area in a safe place,

such as behind a guardrail.

Sealant bottle and filler hose

–

If necessary, set up a warning triangle

at an appropriate distance.

Tire repair set

Principle

With the tire repair set, minor tire damage

can be sealed temporarily to enable contin-

ued driving.

1

2

3

Sealant bottle

Sealant bottle outlet

Filler hose

262

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

pressor and attach it in the visible area

in the vehicle interior.

4

5

Sealant bottle connection

Wheel valve connection

–

Remove the warning label from the tire

sealant bottle and attach it to the rim.

Compressor

Preparing the tire repair set

1. Insert the sealant bottle into the mount

on the housing of the compressor.

1

2

3

4

5

6

Compressor

Tire pressure display

Pressure reducing valve button

Sealant bottle mount

Connector for socket

On/off switch

2. Turn the sealant bottle clockwise by 90°

to the stop.

Safety precautions

–

Park the vehicle as far away as possible

from passing traffic and on solid ground.

–

Turn on the hazard warning system.

Set the parking brake.

Turn the steering wheel until the front

wheels are in the straight-ahead posi-

tion and engage the steering wheel lock.

3. Connect the filler hose to the outlet of

the sealant bottle and turn clockwise by

90° to the stop.

–

As soon as permitted by the traffic flow,

have all vehicle occupants get out and

make sure that they remain outside the

hazardous area such as behind a guard-

rail.

–

If necessary, set up the hazard triangle

or hazard warning lights at an appropri-

ate distance.

Remove the warning label for the max-

imum permissible speed from the com-

263

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

Let the compressor run for max. 10 mi-

nutes to fill in the tire sealant and reach

a tire pressure of 2.5 bar/36 psi.

4. Unscrew the valve cap from the wheel

and screw the connecting piece of the

filler hose onto the valve.

While the tire is being filled with tire

sealant, the tire pressure can briefly

reach approx. 6 bar/87 psi. Do not turn

off the compressor in this phase.

5. With the compressor switched off, in-

sert the connector into the power socket

in the vehicle interior.

Filling the tire with sealing

compound

2. Switch off the compressor.

Checking the tire pressure

Read the tire pressure on the tire pressure

display of the compressor. The tire pressure

must be at least 2.5 bar/36 psi.

Safety information

DANGER

If the exhaust pipe is blocked or ventila-

tion is insufficient, harmful exhaust gases

can penetrate the vehicle. The exhaust

gases contain pollutants which are color-

less and odorless. In enclosed areas, ex-

haust gases can also accumulate outside of

the vehicle. There is a danger to life. Keep

the exhaust pipe free and ensure sufficient

ventilation.

Tire pressure too high

If the tire pressure is too high, reduce the

tire pressure with the pressure reducing

valve on the compressor.

Minimum tire inflation pressure is not

reached

Do not continue driving unless a minimum

tire pressure of 2.5 bar/36 psi is reached.

Contact an authorized service center or

another qualified service center or repair

shop.

NOTICE

The compressor can overheat during ex-

tended operation. There is a risk of dam-

age to property. Do not run the compres-

sor for more than 10 minutes.

Minimum tire inflation pressure is

reached

1. Pull the connector out of the socket in

the vehicle interior.

Filling the tire with sealing compound

1. With standby state or drive-ready state

switched on, switch on the compressor.

2. Disconnect the hose from the sealant

bottle and the valve on the wheel.

264

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

3. Unscrew the valve cap.

4. Insert the connector into the socket in

the vehicle interior.

4. Stow the tire repair set in the cargo

area.

5. Read the tire pressure on the tire pres-

sure display of the compressor.

5. Immediately drive 5 miles/10 km to

ensure that the tire sealant is evenly

distributed in the tire.

Do not continue driving unless a mini-

mum tire pressure of 1.3 bar/19 psi is

displayed. Contact an authorized service

center or another qualified service cen-

ter or repair shop.

Do not exceed the permissible maximum

speed of 50 mph/80 km/h.

If possible, do not drive at speeds less

than 12 mph/20 km/h.

6. Correct the tire pressure to

2.5 bar/36 psi.

Tire sealant may spray from the dam-

aged area during the initial wheel rota-

tions.

–

Increase tire pressure: with standby

or drive-ready state turned on, turn

on the compressor and let it run for a

maximum of 10 minutes.

Adjusting the tire pressure

1. Stop at a suitable location.

–

Reduce tire pressure: press the pres-

sure reducing valve button on the

compressor.

2. Connect the hose directly to the com-

pressor and turn clockwise by 90° until

it audibly engages.

Remove and stow the tire repair set

1. Switch off the compressor.

2. Pull the connector out of the socket in

the vehicle interior.

3. Disconnect the hose from the compres-

sor and the valve on the wheel.

4. Unscrew the valve cap.

5. Stow the tire repair set in the cargo

area.

3. Unscrew the valve cap from the wheel

and screw the connecting piece of the

hose onto the valve.

Continuing the trip

Do not exceed the permissible maximum

speed of 50 mph/80 km/h.

Do not exceed a maximum distance travel-

led of 125 miles/200 km.

Re-initialize the flat tire monitor or reset

the Tire Pressure Monitor.

Replace the faulty tire and the sealant bottle

of the tire repair set promptly.

265

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

System limits

If the tire cannot be made drivable, con-

tact an authorized service center or another

qualified service center or repair shop.

Warning

Insufficiently tight snow chains may dam-

age tires and vehicle components. There

may be a risk of accidents or risk of dam-

age to property. Make sure that the snow

chains are always sufficiently tight. Re-

tighten as needed according to the snow

chain manufacturer's instructions.

With the Tire Pressure Monitor: using seal-

ant can damage the wheel electronics. In

this case, have the electronics checked and

replaced at the next opportunity.

Snow chains

Fine-link snow chains

The manufacturer of the vehicle recom-

mends the use of fine-link snow chains.

Certain types of fine-link snow chains have

been tested by the manufacturer of the ve-

hicle and recommended as road-safe and

suitable.

General information

The manufacturer of the vehicle has deter-

mined certain wheels and tires to be suita-

ble for operation on the vehicle.

Follow the snow chain manufacturer's in-

structions.

For information on suitable snow chains,

contact an authorized service center or

another qualified service center or repair

shop.

Do not initialize the flat tire monitor after

mounting snow chains, as doing so may re-

sult in incorrect readings.

Do not reset the Tire Pressure Monitor after

mounting snow chains, as doing so may re-

sult in incorrect readings.

Use

Use only in pairs on the front wheels, equip-

ped with the tires of the following size:

When driving with snow chains, briefly ac-

tivate Dynamic Traction Control, if needed.

–

195/60 R 16.

195/55 R 17.

205/45 R 18.

Safety information

John Cooper Works:

205/45 R 18.

Warning

Mounting snow chains on unsuitable tires

can cause the snow chains to come into

contact with vehicle parts. There may be

a risk of accidents or risk of damage to

property. Only mount snow chains on tires

that are designated by their manufacturer

as suitable for the use of snow chains.

Maximum speed with snow chains

Do not exceed a speed of 30 mph/50 km/h

when using snow chains.

Changing wheels/tires

General information

When using runflat tires or a flat tire kit, a

wheel does not always need to be changed

266

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

immediately in case of a breakdown when

MOBILITY

there is a tire pressure loss due to a flat tire.

Warning

If necessary, a suitable wheel change tool,

e.g., a jack, is available as an accessory from

an authorized service center or another

qualified service center or repair shop.

The jack may slip on soft, uneven, or

slippery ground, e.g., snow, ice, tiles, etc.

There is a risk of injury. If possible,

change the wheel on a flat, solid, slip-re-

sistant surface.

Safety information

Warning

DANGER

The jack is optimized for lifting the vehi-

cle and for the jacking points on the vehi-

cle only. There is a risk of injury. Do not

lift any other vehicle or cargo using the

jack.

The jack is only provided for short-term

lifting of the vehicle for wheel changes.

Even if all safety precautions are observed,

there is a risk of the raised vehicle falling

if the jack tips over. There is a risk of

injury or danger to life. If the vehicle is

raised with the jack, do not lie under the

vehicle and do not start the engine.

Warning

When the jack is not inserted into the

jacking point provided for this purpose,

the vehicle may be damaged or the jack

may slip when it is being cranked up.

There is a risk of injury or risk of damage

to property. When cranking up the jack,

ensure that it is inserted in the jacking

point next to the wheel well.

Warning

Supports such as wooden blocks under

the jack reduce the load-carrying capacity

of the jack to bear weight. The load-car-

rying capacity of the wooden blocks may

be exceeded and the vehicle may tip over.

There is a risk of injury or danger to life.

Do not place supports under the jack.

Warning

A vehicle that is raised on a jack may fall

off of the jack if lateral forces are exerted

on it. There is a risk of injury and risk of

damage to property. While the vehicle is

raised, do not exert lateral effort on the ve-

hicle or pull abruptly on the vehicle. Have

a stuck wheel removed by an authorized

service center or another qualified service

center or repair shop.

Warning

The jack, issued by the vehicle manufac-

turer, is provided in order to perform a

wheel change in the event of a breakdown.

The jack is not designed for frequent

use, e.g., changing from summer to winter

tires. Using the jack frequently may cause

it to become jammed or damaged. There

is a risk of injury and risk of damage to

property. Only use the jack to change an

emergency or spare wheel in the event of

a breakdown.

267

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

NOTICE

Wheels and tires

able objects, for instance rocks, under the

wheels of both the front and rear axles

against the rolling direction.

Using an impact wrench to loosen or

tighten the wheel lock bolt can damage

the wheel lock bolt. There is a risk of dam-

age to property. Only use a lug wrench to

loosen and tighten the wheel lock bolt.

Preparing the vehicle

–

Park the vehicle on solid and non-slip

ground at a safe distance from road traf-

fic.

–

Turn on the hazard warning system.

Set the parking brake.

Securing the vehicle against rolling

away

Engage a gear or move the selector lever

to position P.

General information

The vehicle manufacturer recommends to

additionally secure the vehicle against roll-

ing away when changing a wheel.

–

As soon as permitted by the traffic flow,

have all vehicle occupants get out of the

vehicle and ensure that they remain out-

side the hazardous area in a safe place,

such as behind a guardrail.

On a level surface

–

Depending on the vehicle equipment,

get wheel change tools and, if necessary,

the emergency wheel from the vehicle.

If necessary, set up a warning triangle

or portable hazard warning light at an

appropriate distance.

–

Secure the vehicle additionally against

rolling away.

Loosen the lug bolts a half turn.

Place wheel chocks or other suitable objects

in front and behind the wheel that is diago-

nal to the wheel to be changed.

Jacking points

On a slight downhill gradient

The jacking points for the vehicle jack are

located at the marked positions.

If you need to change a wheel on a slight

downhill grade, place chocks and other suit-

268

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

3. Extend the jack by turning the jack

crank handle or lever clockwise.

Jacking up the vehicle

Warning

Hands and fingers can be jammed when

using the jack. There is a risk of injury.

Comply with the described hand position

and do not change this position while us-

ing the jack.

1. Hold the vehicle jack with one hand, ar-

row 1, and grasp the jack crank handle

or lever with your other hand, arrow 2.

4. Take your hand away from the jack as

soon as the jack is under load and con-

tinue turning the jack crank handle or

lever with one hand.

5. Make sure that the car jack foot extends

vertically and is at a right angle beneath

the jacking point.

2. Insert the jack into the rectangular re-

cess of the jacking point closest to the

wheel to be changed.

6. Make sure that the car jack foot is ver-

tical and at a right angle beneath the

jacking point after extending the vehicle

jack.

7. Crank the vehicle up until the vehi-

cle jack has the entire surface on the

269

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Wheels and tires

ground and the relevant wheel is maxi-

mum 1.2 inches/3 cm above ground.

ter or repair shop, then have the dam-

aged tire renewed.

Mounting a wheel

Mount one emergency wheel only, as re-

quired.

Emergency wheel

Principle

1. Unscrew the lug bolts.

2. Remove the wheel.

In the event of a flat tire, the emergency

wheel can be used in place of the wheel

with the faulty tire. The emergency wheel

is only intended for temporary use until the

faulty tire/wheel has been replaced.

3. Put the new wheel or emergency wheel

on and screw in at least two lug bolts in

a crosswise pattern until hand-tight.

If non-original light-alloy wheels of the

vehicle manufacturer are mounted, the

accompanying lug bolts may have to be

used as well.

General information

Mount one emergency wheel only.

Also check the tire inflation pressure of

the emergency wheel in the cargo area reg-

ularly, and correct it as needed.

4. Hand-tighten the remaining lug bolts

and tighten all lug bolts well in a cross-

wise pattern.

5. Turn the jack crank handle counter-

clockwise to retract the jack and lower

the vehicle.

Safety information

Warning

6. Remove the jack and stow it securely.

The emergency wheel has particular di-

mensions. When driving with an emer-

gency wheel, changed driving properties

may occur, for instance reduced direc-

tional stability when braking, longer brak-

ing distance, and changed self-steering

properties in the limit range. There is a

risk of accident. Drive moderately and do

not exceed a speed of 50 mph/80 km/h.

After the wheel change

1. Tighten the lug bolts cross-

wise. The tightening torque is

101 lbs ft/140 Nm.

2. Stow the faulty wheel in the cargo area,

if necessary.

The faulty wheel cannot be stored under

the cargo area floor because of its size.

3. Check tire inflation pressure at the next

opportunity and correct as needed.

4. Reinitialize the Flat Tire Monitor.

Reset the Tire Pressure Monitor again.

5. Check to make sure the lug bolts are

tight with a calibrated torque wrench.

6. Drive to the nearest authorized service

center or another qualified service cen-

270

Online Edition for Part no. 01405A7B0F2 - II/23

Wheels and tires

MOBILITY

Overview

The emergency wheel and the wheel change

tools are located in the cargo area under the

cargo area floor.

Removing the emergency wheel

1. Pull up and remove the cargo area floor.

2. Unscrew the wing screw.

3. Remove the retaining plate or the cover.

4. Where applicable, remove the holder

and the trailer hitch.

5. Remove the jacking point and the tool

holder on the left next to the emergency

wheel.

6. Slide the emergency wheel to the left

and remove it.

Inserting the emergency wheel

1. Insert the emergency wheel on the left

and slide it to the right.

2. Where applicable, mount the holder and

the trailer hitch.

3. Attach the retaining plate or the cover.

4. Screw on and tighten the wing screw.

5. Insert and secure the jacking point and

the tool holder on the left next to the

emergency wheel.

6. Insert the cargo area floor.

271

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Engine compartment

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

Vehicle features and options

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

Overview

1

2

3

Filler neck for washer fluid

Vehicle identification number

Oil filler neck

4

5

6

Jump-starting, positive terminal

Jump-starting, negative terminal

Coolant reservoir

272

Online Edition for Part no. 01405A7B0F2 - II/23

Engine compartment

MOBILITY

Hood

Warning

Body parts can be jammed when opening

and closing the hood. There is a risk of in-

jury. Make sure that the travel path of the

hood is clear during opening and closing.

Safety information

Warning

Improperly executed work in the engine

compartment can damage vehicle compo-

nents and impair vehicle functions. There

is a risk of an accident and damage to

property. The manufacturer of the vehicle

recommends that, in the effort to avoid

such risks, work in the engine compart-

ment be performed by an authorized serv-

ice center or another qualified service cen-

ter or repair shop.

NOTICE

Folded-away wipers can be jammed when

the hood is opened. There is a risk of dam-

age to property. Make sure that the wipers

with the wiper blades mounted are folded

down onto the windshield before opening

the hood.

NOTICE

Warning

When the hood is closed, it must engage

on both sides. Pressing again can dam-

age the hood. There is a risk of damage

to property. Open the hood again and

then close it energetically. Avoid pressing

again.

The engine compartment accommodates

moving components. Certain components

in the engine compartment can also move

with the vehicle switched off, for instance

the radiator fan. There is a risk of injury.

Do not reach into the area of moving parts.

Keep articles of clothing and hair away

from moving parts.

Opening the hood

1. Pull lever, arrow 1.

Hood is unlocked.

Warning

There are protruding parts, for instance

locking hooks, on the inside of the hood.

There is a risk of injury. If the hood is

open, pay attention to protruding parts

and keep clear of these areas.

Warning

An incorrectly locked hood can open while

driving and restrict the view. There is a

risk of accident. Stop immediately and cor-

rectly close the hood.

2. After the lever is released, pull the lever

again, arrow 2.

Hood can be opened.

273

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Engine compartment

Indicator/warning lights

When the hood is opened, a Check Control

message is displayed.

Closing the hood

Energetically close the hood from approx.

20 in/50 cm.

The hood must engage on both sides.

274

Online Edition for Part no. 01405A7B0F2 - II/23

Engine oil

MOBILITY

Engine oil

Vehicle features and options

Safety information

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

NOTICE

An engine oil level that is too low causes

engine damage. There is a risk of damage

to property. Immediately add engine oil.

NOTICE

Too much engine oil can damage the en-

gine or the catalytic converter. There is a

risk of damage to property. Do not add too

much engine oil. If there is excess engine

oil, have the engine oil level corrected by

an authorized service center or another

qualified service center or repair shop.

General information

The engine oil consumption is dependent on

your driving style and driving conditions.

Therefore, regularly check the engine oil

level after refueling by taking a detailed

measurement.

NOTICE

Engine oil that is not changed in timely

fashion can cause increased engine wear

and thus engine damage. There is a risk

of damage to property. It is recommended

that you do not exceed the service inter-

vals indicated in the vehicle.

The engine oil consumption can increase in

the following situations, for instance:

–

Sporty driving style.

Break-in of the engine.

Idle operation of the engine.

With use of engine oil types that are

classified as not suitable.

Different Check Control messages appear,

depending on the engine oil level.

Electronic oil measurement

The vehicle manufacturer recommends hav-

ing the engine oil changed by an authorized

service center or another qualified service

center or repair shop.

General information

The electronic oil measurement has two

measuring principles:

–

Monitoring.

Detailed measurement.

When making frequent short-distance trips

or using a dynamic driving style, for in-

275

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Engine oil

stance when cornering aggressively, regu-

larly perform a detailed measurement.

General information

During the measurement, the idle speed is

increased somewhat.

Monitoring

Principle

The engine oil level is monitored electroni-

cally while driving and can be shown on the

control display.

Functional requirements

–

Vehicle is parked in a horizontal posi-

tion.

–

Manual transmission: gearshift lever in

idle position, clutch and accelerator ped-

als not depressed.

If the engine oil level is outside its permis-

sible operating range, a Check Control mes-

sage is displayed.

–

Steptronic transmission: selector lever

in selector lever position N or P and ac-

celerator pedal not depressed.

Functional requirements

A current measured value is available after

approx. 30 minutes of normal driving.

Engine is running and is at operating

temperature.

Performing a detailed measurement

Via the Central Information Display (CID):

Displaying the engine oil level

Via the Central Information Display (CID):

1.

"My MINI"

1.

"My MINI"

2. "Vehicle status"

3.

"Engine oil level"

3.

"Engine oil level"

4. "Measure engine oil level"

5. "Start measurement"

The engine oil level is displayed.

System limits

The engine oil level is checked and dis-

played via a scale.

When making frequent short-distance trips

or using a dynamic driving style, it may not

be possible to calculate a measured value.

In this case, the measured value for the last,

sufficiently long trip is displayed.

Adding engine oil

General information

Detailed measurement

Principle

The engine oil level is checked when the ve-

hicle is stationary and displayed via a scale.

Only add engine oil when the message is

displayed in the instrument cluster. The

top-up quantity is indicated in the message

displayed in the instrument cluster.

Only add suitable types of engine oil, refer

to page 278.

If the engine oil level is outside its permis-

sible operating range, a Check Control mes-

sage is displayed.

Safely park the vehicle and switch off the

ignition before adding engine oil.

Take care not to add too much engine oil.

276

Online Edition for Part no. 01405A7B0F2 - II/23

Engine oil

MOBILITY

Safety information

Adding engine oil

1. Open the hood, refer to page 273.

Warning

2. Open the lid counterclockwise.

Operating materials, for instance oils,

greases, coolants, fuels, can contain harm-

ful ingredients. There is a risk of injury

or danger to life. Follow the instructions

on the containers. Avoid the contact of

articles of clothing, skin or eyes with op-

erating materials. Do not refill operating

materials into different bottles. Store oper-

ating materials out of reach of children.

3. Add engine oil.

4. Close the lid.

NOTICE

An engine oil level that is too low causes

engine damage. There is a risk of damage

to property. Immediately add engine oil.

Engine oil types to add

General information

The engine oil grade is critical for the serv-

ice life of the engine.

NOTICE

Too much engine oil can damage the en-

gine or the catalytic converter. There is a

risk of damage to property. Do not add too

much engine oil. If there is excess engine

oil, have the engine oil level corrected by

an authorized service center or another

qualified service center or repair shop.

Only add with the types of engine oil which

are listed.

Safety information

NOTICE

Oil additives can damage the engine.

There is a risk of damage to property. Do

not use oil additives.

Overview

The oil filler neck is located in the engine

compartment, refer to page 272.

NOTICE

Incorrect engine oil can cause malfunc-

tions in the engine or damage it. There

is a risk of damage to property. When se-

lecting an engine oil, make sure that the

engine oil has the correct oil specification.

277

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Engine oil

Suitable engine oil types

When topping up engine oil, the following

oil specification applies:

Gasoline engine

BMW Longlife-17 FE+.

Alternative engine oil types

If an engine oil suitable for continuous use

is not available, up to 1 US quart/liter of an

engine oil with the following oil rating can

be added:

Oil specification

API SL.

API SM.

API SN.

Viscosity grades

When selecting an engine oil, make sure

that the engine oil has a suitable viscosity

grade. The suitable viscosity grade is indi-

cated on a sign in the engine compartment.

Viscosity grades

SAE 0W-20.

More information about suitable oil specifi-

cations and engine oil viscosity grades can

be requested from an authorized service

center or another qualified service center

or repair shop.

278

Online Edition for Part no. 01405A7B0F2 - II/23

Coolant

MOBILITY

Coolant

Vehicle features and options

Warning

Additives are harmful and incorrect addi-

tives can damage the engine. There is a

risk of injury and risk of damage to prop-

erty. Do not allow additives to come into

contact with skin, eyes or articles of cloth-

ing. Use suitable additives only.

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

Coolant level

Checking

There are yellow minimum and maximum

marks in the coolant reservoir.

General information

Coolant consists of water and coolant addi-

tive.

1. Let the engine cool down.

2. Open the hood, refer to page 273.

Not all commercially available coolant addi-

tives are suitable for the vehicle. The vehi-

cle manufacturer recommends using coolant

with the BMW LC-18 specification. Do not

mix coolant additives of different colors.

Use a 50:50 mixing ratio of water to coolant

additive. Information on suitable coolant ad-

ditives can be provided by an authorized

service center or another qualified service

center or repair shop.

3. Turn the lid of the coolant reservoir

slightly counterclockwise to allow any

excess pressure to dissipate, then open

it.

Safety information

4. Open the coolant reservoir lid.

Warning

With the engine hot and the cooling sys-

tem open, coolant can escape and lead to

scalding. There is a risk of injury. Only

open the cooling system with the engine

cooled down.

279

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Coolant

5. The coolant level is correct if it lies

between the minimum and maximum

marks in the filler neck.

Disposal

Comply with the relevant environ-

mental protection regulations when

disposing of coolant and coolant ad-

ditives.

6. Close the lid.

Adding coolant

1. Let the engine cool down.

2. Open the hood, refer to page 273.

3. Turn the lid of the coolant reservoir

slightly counterclockwise to allow any

excess pressure to dissipate, then open

it.

4. Open the coolant reservoir lid.

5. If the coolant is low, slowly add coolant

up to the specified fill level; do not over-

fill.

6. Close the lid.

7. Have the cause of the coolant loss elimi-

nated as soon as possible.

280

Online Edition for Part no. 01405A7B0F2 - II/23

Maintenance

MOBILITY

Maintenance

The system makes it possible to adapt the

amount of maintenance corresponding to

your user profile.

Vehicle features and options

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

General information

Information on service notifications, refer

to page 134, can be displayed on the con-

trol display.

Service data in the vehicle key

Information on the service notifications is

continuously stored in the vehicle key. The

authorized service center can read this data

out and suggest a maintenance scope for

the vehicle.

MINI maintenance system

Therefore, hand the service advisor the ve-

hicle key with which the vehicle was driven

most recently.

The maintenance system provides service

notifications and thereby provides support

in maintaining road safety and the opera-

tional reliability of the vehicle.

Stationary periods

In some cases, scopes and intervals of the

maintenance system may vary according

to the country version. Replacement work,

spare parts, fuels and lubricants, and wear

materials are calculated separately. Further

information is available from an authorized

service center or another qualified service

center or repair shop.

Stationary periods during which the vehicle

battery was disconnected are not taken into

account.

Have an authorized service center or an-

other qualified service center or repair shop

perform time-dependent maintenance pro-

cedures, e.g., checking the brake fluid, en-

gine oil, and microfilter/carbon filter.

Condition Based Service

Maintenance Booklet for US

Models

Principle

Condition Based Service determines the

maintenance recommendation using sen-

sors and special algorithms that take into

account the operating conditions of the ve-

hicle.

Please consult your Maintenance Booklet

for additional information on the perform-

ance of service and maintenance work.

The manufacturer of the vehicle recom-

mends that maintenance and repair be per-

formed by an authorized service center or

another qualified service center or repair

281

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Maintenance

shop. Records of regular maintenance and

repair work should be retained.

Position

Diagnostic socket

General information

Devices connected to the diagnostic socket

will trigger the alarm system after locking

the vehicle. Remove devices connected to

the diagnostic socket before locking the ve-

hicle.

On the driver’s side, there is a socket for on-

board diagnosis to check components that

are relevant for the vehicle's emission mix.

Safety information

Emissions

NOTICE

–

The warning light illuminates:

The socket for Onboard Diagnosis is an

intricate component intended to be used

in conjunction with specialized equipment

to check the vehicle’s primary emissions

system. Improper use of the socket for

Onboard Diagnosis, or contact with the

socket for Onboard Diagnosis for other

than its intended purpose, can cause ve-

hicle malfunctions and creates risks of

personal and property damage. Given the

foregoing, the manufacture of the vehicle

strongly recommends that access to the

socket for Onboard Diagnosis be limited

to an authorized service center or another

qualified service center or repair shop or

other persons that have the specialized

training and equipment for purposes of

properly utilizing the socket for Onboard

Diagnosis.

Emissions are deteriorating.

Have the vehicle checked as soon

as possible.

–

The warning light flashes under certain

circumstances:

This indicates that there is excessive

misfiring in the engine.

Reduce the vehicle speed and have the

vehicle checked immediately; otherwise,

serious engine misfiring within a brief

period can seriously damage emission

control components, in particular the

catalytic converter.

282

Online Edition for Part no. 01405A7B0F2 - II/23

Replacing components

MOBILITY

Replacing components

Vehicle features and options

Wiper blades

Safety information

NOTICE

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

The window may sustain damage if the

wiper falls onto it without the wiper

blade installed. There is a risk of damage

to property. Hold the wiper firmly when

changing the wiper blade. Do not fold in or

switch on the wiper without a wiper blade

installed.

Onboard vehicle tool kit

NOTICE

Folded-away wipers can be jammed when

the hood is opened. There is a risk of dam-

age to property. Make sure that the wipers

with the wiper blades mounted are folded

down onto the windshield before opening

the hood.

Replacing the front wiper blades

1. To change the wiper blades, bring wip-

ers into fold-out position.

The bag containing the onboard vehicle tool

kit is located beneath the cargo floor panel.

2. Fold out and hold the wiper arm firmly.

After use, secure the bag with the onboard

vehicle tool kit on a lashing eye again.

3. Press button, arrow 1, and pull out the

wiper blade, arrow 2.

283

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Replacing components

A replacement bulb set is available from an

authorized service center or another quali-

fied service center or repair shop.

4. Attach a new wiper blade. The wiper

blade must engage audibly.

5. Fold in the wiper arm.

Follow the safety information, refer to

page 284.

Replacing rear wiper blades

1. Fold out and hold the wiper arm firmly.

Light-emitting diodes (LEDs)

2. Turn back the wiper blade to the stop.

Some items of equipment use light-emitting

diodes installed behind a cover as a light

source. These light-emitting diodes are re-

lated to conventional lasers and are offi-

cially designated as Class 1 light-emitting

diodes.

Follow the safety information, refer to

page 284.

Safety information

Lights and bulbs

3. Push the wiper blade out of the fasten-

ing by continuing to turn it to the stop.

4. Insert the new wiper blade by following

the steps in reverse order. The wiper

blade must engage audibly.

Warning

Bulbs can get hot during operation. Con-

tact with the bulbs can cause burns. There

is a risk of injury. Only change bulbs after

they have cooled off.

5. Fold in the wiper arm.

Light and bulb replacement

Warning

General information

Lights and bulbs

Lights and bulbs make an essential contri-

bution to driving safety.

Work on switched-on lighting systems can

cause short circuits. There is a risk of in-

jury or risk of damage to property. When

working on the lighting system, switch off

the lights in question. If necessary, heed

the bulb manufacturer's instructions.

Except for the side turn signal lamps and

the lights in the rear bumper, all headlights

and lights are designed in LED technology.

The vehicle manufacturer recommends hav-

ing necessary work performed by an au-

thorized service center or another qualified

service center or repair shop if you are un-

familiar with performing this work or if it

has not been described here.

NOTICE

Dirty bulbs have a reduced service life.

There is a risk of damage to property. Do

not hold new glass bulbs with your bare

hands. Use a clean cloth or something sim-

ilar, or hold the bulb by its base.

284

Online Edition for Part no. 01405A7B0F2 - II/23

Replacing components

MOBILITY

In the event of a malfunction, contact an au-

thorized service center or another qualified

service center or repair shop.

Light-emitting diodes (LEDs)

Warning

Intense brightness can irritate or damage

the retina of the eye. There is a risk of

injury. Do not look directly into the head-

lights or other light sources. Do not re-

move the LED covers.

Tail lights in bumpers

Follow the general instructions on lights

and bulbs, refer to page 284.

In addition, the tail lights in the bumper

assume the functions of the brake light, tail

light and turn signals, if the split doors are

open.

Headlight glass

The inside of the headlight glass can fog

up in cool or humid weather. When driving

with the lights switched on, the condensa-

tion evaporates after a short time. The head-

light glass does not need to be changed.

Overview

If, despite driving with the headlights

switched on, moisture such as water drop-

lets increasingly forms in the light, have the

headlights checked.

Tail lights, bulb exchange

Overview

1

2

Tail lights/brake lights/turn signal

Brake lights/turn signals

Tail lights/brake lights/turn signal

21-watt bulbs, P21W.

1. Press out cover below the tail light.

1

2

3

4

Tail lights in split doors

Tail lights in bumpers

License plate light

Center brake light

2. Remove the screwdriver from the on-

board vehicle tool kit.

Tail lights in split doors, Union Jack

All lamps in the split doors feature LED

technology.

285

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Replacing components

3. Pull the screwdriver blade from the han-

dle and place it on the Phillips screw

head in the bumper.

7. Turn the light bracket counter-clock-

wise and remove nonworking bulb.

8. To insert the new bulb and install the

tail light, proceed in reverse order of re-

moval. Make sure that the light bracket

sits tight in the tail light.

4. Attach the screw driver handle with the

slot to the blade, arrow 1.

Central brake light and license plate

lights

Follow the general instructions on lights

and bulbs, refer to page 284.

The lights feature LED technology. In the

event of a malfunction, contact an author-

ized service center or another qualified

service center or repair shop.

5. Loosen screw in the bumper, arrow 2.

6. Pull tail light from the bumper.

Side turn signal lamps, bulb

exchange

Follow the general instructions on lights

and bulbs, refer to page 284.

286

Online Edition for Part no. 01405A7B0F2 - II/23

Replacing components

MOBILITY

Bulbs:

With white lens: WY5W.

Vehicle battery

–

1. Open the hood. The covers of the side

turn signal lamps are on the left and

right next to the hinges of the hood.

General information

The battery is maintenance-free.

More information on the battery can be re-

quested from an authorized service center

or another qualified service center or repair

shop.

Safety information

DANGER

Contact with live components can lead to

an electric shock. There is a risk of injury

or danger to life. Do not touch any compo-

nents that are under voltage.

2. Loosen the nuts of the cover by hand or

with the onboard vehicle tool kit, refer

to page 283, and remove the cover.

Warning

Vehicle batteries that are not compatible

can damage vehicle systems and impair

vehicle functions. There is a risk of an

accident and damage to property. Only ve-

hicle batteries that are compatible with

the vehicle type should be installed in

the vehicle. Information on compatible ve-

hicle batteries is available at an authorized

service center.

3. Turn the bulb socket counterclockwise

and remove.

Registering the battery to the

vehicle

The vehicle manufacturer recommends hav-

ing an authorized service center or another

qualified service center or repair shop regis-

ter the vehicle battery to the vehicle after

the battery has been changed. Once the bat-

tery has been registered again, all comfort

features will be available without limitation

and any Check Control messages displayed

which relate to comfort features will disap-

pear.

4. Replace the bulb.

5. To insert the new bulb, proceed in re-

verse order of removal.

Insert the nuts of the cover and press

down.

287

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Replacing components

–

Memory function: store the positions

again.

Charging the battery

General information

Make sure that the battery is always suffi-

ciently charged to guarantee that the bat-

tery remains usable for its full service life.

–

Time: update.

Date: update.

Glass sunroof: initialize the system.

Disposing of old batteries

A discharged battery is indicated by

a red indicator light.

Have old batteries disposed of by

an authorized service center or an-

other qualified service center or re-

pair shop, or take them to a collection point.

Charge the battery when acceleration is in-

sufficient.

The following circumstances can have a

negative effect on the performance of the

battery:

Maintain the filled battery in an upright po-

sition for transport and storage. Secure the

battery so that it does not tip over during

transport.

–

Frequent short-distance drives.

Stationary periods of more than one

month.

Fuses

Safety information

Warning

Battery chargers that charge the vehicle

battery via sockets or cigarette lighters in

the vehicle may overload or damage the

12 V electrical system. There is a risk of

injury or risk of damage to property. Only

connect battery chargers for the vehicle

battery to the jump-start terminals in the

engine compartment.

Warning

Incorrect and repaired fuses can overload

electrical lines and components. There is

a risk of fire. Never attempt to repair a

blown fuse. Do not replace a nonworking

fuse with a substitute of another color or

amperage rating.

Charging the battery

Charge the battery only when the engine is

off and via the jump-start terminals, refer to

page 293, in the engine compartment.

Power interruption

After a power interruption, some equipment

needs to be newly initialized or individual

settings updated, for example:

288

Online Edition for Part no. 01405A7B0F2 - II/23

Replacing components

MOBILITY

Accessing the fuses

The fuses are located in the glove compart-

ment.

1. Open the glove compartment.

2. Swing the cover down, arrow.

Information on the fuse layout, as well as

the positions of any other fuse boxes, is

fusecard.

Where applicable, information on the fuse

layout is also found on a separate sheet in

the fuse box.

Replacing fuses

The vehicle manufacturer recommends hav-

ing the fuses replaced by an authorized

service center or another qualified service

center or repair shop.

289

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Breakdown Assistance

Vehicle features and options

First-aid kit

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

General information

Depending on the vehicle equipment and

country-specific version, the vehicle is

equipped with a first-aid kit.

Some of the articles have a limited service

life.

Check the expiration dates of the contents

regularly and replace any expired items

promptly.

Storage

Hazard warning flashers

Storage for the first-aid kit is provided in

the cargo area.

MINI Roadside Assistance

Principle

MINI Roadside Assistance can be contacted

if assistance is needed in the event of a

breakdown.

The button is located above the control dis-

play.

General information

In the event of a breakdown, data on the

vehicle's condition is sent to the vehicle

manufacturer.

The red light in the button flashes when the

hazard warning flashers are activated.

There are various ways of making contact.

–

Via a Check Control message, refer to

page 127.

Warning triangle

–

Calling with a mobile phone.

Depending on the equipment, the warning

triangle is located in the cargo area under

the cargo area floor.

290

Online Edition for Part no. 01405A7B0F2 - II/23

Breakdown Assistance

MOBILITY

If this is not possible, further measures will

be initiated, for instance Mobile Assistance

vehicle will be informed.

Prerequisites

–

Active MINI Connected contract or

equipment version with intelligent

emergency call.

–

Cellular network reception.

The ignition is switched on.

Emergency Call

Intelligent emergency call

Principle

In case of an emergency, an emergency call

can be triggered automatically by the sys-

tem or manually.

Starting

If the vehicle is equipped with Teleservices,

support is offered through Teleservice Diag-

nosis.

Via the Central Information Display (CID):

1.

"MINI Connected"

General information

2. "MINI Assist"

Depending on vehicle equipment and na-

tional-market version, the vehicle is equip-

ped with an Assist system.

3. "MINI Roadside Assistance"

The contact to the MINI Roadside Assis-

tance is established.

Only press the SOS button in an emergency.

A telephone number is displayed, if

needed. Select to dial the telephone

number on a connected mobile phone.

The Intelligent Assist system establishes a

connection with the MINI Response Center.

For technical reasons, the emergency call

cannot be guaranteed under unfavorable

conditions.

Teleservice Diagnosis

Teleservice Diagnosis enables the wireless

transmission of detailed vehicle data that is

important for vehicle diagnosis. This data is

transmitted automatically.

Overview

Teleservice Help

Depending on the country, the Teleservice

Help enables a more in-depth diagnosis of

the vehicle via wireless transmission.

You can launch Teleservice Help by re-

questing it through the Service Specialist.

SOS button in the headliner

1. Park the vehicle in a safe place.

2. Set the parking brake.

3. Control display is switched on.

4. Confirm Teleservice Help.

The driving ability of the vehicle can be

restored for specific functions.

291

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Breakdown Assistance

the hands-free system, for instance, may

Functional requirements

be broken. However, the MINI Response

Center may still be able to hear you.

–

The ignition is switched on.

The Assist system is functional.

The MINI Response Center ends the emer-

gency call.

If the vehicle is equipped with intelli-

gent emergency call: the integrated SIM

card in the vehicle has been activated.

Jump-starting

Automatic triggering

When certain prerequisites are met, for in-

stance if the airbags deploy, an emergency

call is automatically initiated immediately

after an accident of corresponding severity.

Automatic Collision Notification is not af-

fected by pressing the SOS button.

General information

If the battery is discharged, the engine can

be started using the battery of another vehi-

cle and two jumper cables. Only use jumper

cables with fully insulated clamp handles.

Manual triggering

Safety information

1. Press the cover flap briefly to open it.

DANGER

2. Press the SOS button until the LED at

the button illuminates green.

Contact with live components can lead to

an electric shock. There is a risk of injury

or danger to life. Do not touch any compo-

nents that are under voltage.

–

The LED is illuminated green when an

emergency call has been initiated.

If the situation allows, wait in the vehi-

cle until the voice connection has been

established.

Warning

–

The LED flashes green when a connec-

tion to the MINI Response Center has

been established.

If the jumper cables are connected in the

incorrect order, spark formation may oc-

cur. There is a risk of injury. Pay attention

to the correct order during connection.

The MINI Response Center then makes

contact with you and takes further steps

to help you.

Even if you are unable to respond, the

MINI Response Center can take further

steps to help you under certain circum-

stances.

Warning

In the case of body contact between the

two vehicles, a short circuit can occur dur-

ing jump-starting. There is a risk of injury

or risk of damage to property. Make sure

that no body contact occurs.

For this purpose, data that serves to de-

termine the necessary rescue measures,

for instance the current position of the

vehicle when it can be determined, is

transmitted to the MINI Response Cen-

ter.

Preparation

1. Check whether the battery of the other

vehicle has a voltage of 12 volts. The

If you can no longer hear the MINI Re-

sponse Center through the loudspeakers,

292

Online Edition for Part no. 01405A7B0F2 - II/23

Breakdown Assistance

voltage information can be found on the

MOBILITY

Starting the engine

battery.

Never use spray fluids to start the engine.

2. Switch off the engine of the assisting

vehicle.

1. Start the engine of the assisting vehicle

and let it run for several minutes at an

increased idle speed.

3. Switch off any electrical components in

both vehicles.

2. Start the engine of the vehicle that is to

be started in the usual way.

Jump-start terminals

If the first attempt to start the engine

is not successful, wait a few minutes

before making another attempt in order

to allow the discharged battery to re-

charge.

The jump-start terminal in the engine com-

partment, refer to page 272, acts as the

positive battery terminal.

Open the lid of the jump-start terminal.

The body ground or a special connection on

the body in the engine compartment, refer

to page 272, acts as the negative battery

terminal.

3. Let both engines run for several mi-

nutes.

4. Disconnect the jumper cables in the re-

verse order.

Check the battery and recharge, if needed.

Connecting the cables

To prevent personal injury or damage to

both vehicles, adhere strictly to the follow-

ing procedure.

Tow-starting and towing

Safety information

Warning

1. Pull off the cover cap of the jump-start

terminal.

2. Attach one terminal clamp of the posi-

tive jumper cable to the positive battery

terminal, or to the corresponding jump-

start terminal of the vehicle providing

assistance.

When towing with Intelligent Safety sys-

tems enabled or Cruise Control switched

on, individual functions may not work

correctly. There is a risk of accident.

Switch off all Intelligent Safety systems

and Cruise Control before towing.

3. Attach the terminal clamp on the other

end of the cable to the positive bat-

tery terminal, or to the corresponding

jump-start terminal of the vehicle to be

started.

Manual transmission

4. Attach one terminal clamp of the neg-

ative jumper cable to the negative bat-

tery terminal, or to the corresponding

engine or body ground of assisting vehi-

cle.

Towing or pushing the vehicle

A broken-down vehicle can be towed or

pushed.

For rolling or pushing the vehicle, refer to

page 117.

5. Attach the second terminal clamp to the

negative battery terminal, or to the cor-

responding engine or body ground of

the vehicle to be started.

293

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

NOTICE

Breakdown Assistance

Tow truck

With driven front axle

If manual unlocking of the parking brake

is not possible, the vehicle cannot be

moved or towed. There is a risk of damage

to property. The vehicle should only be

transported on a loading platform.

Follow the following instructions:

–

Make sure that the ignition is switched

on; otherwise, the low beams, tail lights,

turn signals, and wipers may be unavail-

able.

The vehicle should be transported with a

tow truck with a so-called spectacle lift or

on a loading platform.

–

Do not tow the vehicle with the rear

axle tilted, as the front wheels could

turn.

When the engine is stopped, there is no

power assistance. Consequently, more

effort needs to be applied when braking

and steering.

With ALL4

NOTICE

The vehicle can be damaged when towing

the vehicle with a single lifted axle. There

is a risk of damage to property. The vehi-

cle should only be transported on a loading

platform.

–

Larger steering wheel movements are

required.

The towing vehicle must not be lighter

than the vehicle being towed; otherwise,

it will not be possible to control han-

dling.

–

Do not exceed a towing speed of

30 mph/50 km/h.

Do not exceed a towing distance of

30 miles/50 km.

Have the vehicle transported on a loading

platform only

294

Online Edition for Part no. 01405A7B0F2 - II/23

Breakdown Assistance

Tow truck

MOBILITY

Steptronic transmission with

driven front axle: transporting the

vehicle

General information

The vehicle must not be towed if the front

wheels are touching the ground.

Safety information

The vehicle should be transported with a

tow truck with a so-called spectacle lift or

on a loading platform.

NOTICE

The vehicle can be damaged when towing

the vehicle with a lifted rear axle. There is

a risk of damage to property. Have vehicle

towed only with lifted front axle or on a

loading platform.

Steptronic transmission with ALL4:

transporting the vehicle

General information

Warning

Do not transport the vehicle by towing it.

The vehicle can become damaged when

lifting and securing it.

Pushing the vehicle

To remove a broken-down vehicle from

the hazardous area, push it for a short

distance at a speed of no more than

6 mph/10 km/h.

There is a risk of injury or risk of damage

to property.

–

Lift the vehicle using suitable means.

Do not lift or secure the vehicle by its

tow fitting, body parts, or suspension

parts.

For rolling or pushing the vehicle, refer to

page 119.

Tow truck

Pushing the vehicle

To remove a broken-down vehicle from

the hazardous area, push it for a short

distance at a speed of no more than

6 mph/10 km/h.

Warning

The vehicle can become damaged when

lifting and securing it.

There is a risk of injury or risk of damage

to property.

For rolling or pushing the vehicle, refer to

page 119.

–

Lift the vehicle using suitable means.

Do not lift or secure the vehicle by its

tow fitting, body parts, or suspension

parts.

295

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Breakdown Assistance

Tow bar

The tow fittings used should be on the same

side on both vehicles.

If it is impossible to avoid mounting the

tow bar at an inclination, note the following:

–

Free movement is limited when corner-

ing.

–

The tow bar will generate lateral forces

if it is secured with an inclination.

The vehicle should only be transported on a

loading platform.

Tow rope

Observe the following notes when using the

tow rope:

Towing other vehicles

General information

Switch on the hazard warning system, de-

pending on local regulations.

–

Use nylon ropes or straps, which will

enable the vehicle to be towed without

jerking.

–

Make sure the tow rope is not twisted

when fastening.

If the electrical system has failed, clearly

identify the vehicle being towed by placing

a sign or a warning triangle in the rear win-

dow.

Check the attachment of the tow fitting

and tow rope in regular intervals.

Do not exceed a towing speed of

30 mph/50 km/h.

Safety information

Do not exceed a towing distance of

3 miles/5 km.

Warning

When driving off to tow the vehicle,

make sure that the tow rope is taut.

If the approved gross vehicle weight of the

towing vehicle is lighter than the vehicle

to be towed, the tow fitting can tear off or

it will not be possible to control handling.

There is a risk of accident. Make sure that

the gross vehicle weight of the towing

vehicle is heavier than the vehicle to be

towed.

Tow fitting

General information

NOTICE

If the tow bar or tow rope is attached in-

correctly, damage to other vehicle parts

can occur. There is a risk of damage to

property. Correctly attach the tow bar or

tow rope to the tow fitting.

The screw-in tow fitting should always be

carried in the vehicle.

296

Online Edition for Part no. 01405A7B0F2 - II/23

Breakdown Assistance

MOBILITY

The tow fitting can be screwed in at the

front or rear of the vehicle.

Tow-starting

Manual transmission

The tow fitting and the onboard vehicle tool

kit, refer to page 283, are together in the

cargo area.

If possible, do not tow-start the vehicle but

start the engine by jump-starting, refer to

page 292. If the vehicle is equipped with a

catalytic converter, only tow-start while the

engine is cold.

Use of the tow fitting:

–

Use only the tow fitting provided with

the vehicle and screw it in to the stop.

Use the tow fitting for towing on paved

roads only.

1. Switch on the hazard warning system

and comply with local regulations.

Avoid lateral loading of the tow fitting,

for instance do not lift the vehicle by the

tow fitting.

2. Switch on the ignition, refer to

page 100.

3. Engage third gear.

–

Check the attachment of the tow fitting

in regular intervals.

4. Have the vehicle tow-started with the

clutch pedal pressed and slowly release

the pedal. After the engine starts, imme-

diately press on the clutch pedal again.

Safety information

NOTICE

5. Stop at a suitable location, remove the

tow bar or tow rope, and switch off the

hazard warning system.

If the tow fitting is not used as intended,

there may be damage to the vehicle or to

the tow fitting. There is a risk of damage

to property. Follow the notes on using the

tow fitting.

6. Have vehicle checked by an authorized

service center or another qualified serv-

ice center or repair shop.

Steptronic transmission

Do not tow-start the vehicle.

Screw thread for tow fitting

Tow-starting the engine is not possible due

to the Steptronic transmission.

Have the cause of starting issues corrected

by an authorized service center or another

qualified service center or repair shop.

Threaded holes for the tow fitting are lo-

cated in the front and rear of the vehicle

on the right side with respect to the driving

direction.

Press on the mark on the edge of the cover

to push it out.

297

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Vehicle Care

Steam cleaners or high pressure

cleaners

Vehicle features and options

This chapter describes all standard, coun-

try-specific and optional equipment offered

with the series. It also describes features

and functions that are not necessarily avail-

able in the vehicle, e.g., due to the selected

options or country versions. This also ap-

plies to safety-related functions and sys-

tems. When using these functions and sys-

tems, the applicable laws and regulations

must be observed.

Safety information

NOTICE

When cleaning with high pressure clean-

ers, components can be damaged due to

the pressure or temperatures being too

high. There is a risk of damage to property.

Maintain sufficient distance and do not

spray too long continuously. Follow the

operating instructions for the high pres-

sure cleaners.

Washing the vehicle

Distances and temperature

General information

Regularly remove foreign bodies such as

leaves in the area below the windshield

when the hood is raised.

–

Maximum temperature: 140 ℉/60 ℃.

Minimum distance from sensors, cam-

eras, seals and lights: 12 inches/30 cm.

Wash the vehicle frequently, particularly in

winter. Intense contamination and road salt

can damage the vehicle.

–

Minimum distance from glass sunroof:

31.5 in/80 cm.

Automatic car washes or car

washes

Safety information

NOTICE

When washing with an open fuel filler

flap, damage may occur. There is a risk

of damage to property. Close the fuel filler

flap before washing. Clean dirt behind the

fuel filler flap with a cloth.

NOTICE

Improper use of automatic car washes can

cause damage to the vehicle. There is a

risk of damage to property. Follow the fol-

lowing instructions:

–

Give preference to cloth car washes

or those that use soft brushes in or-

der to avoid paint damage.

–

Do not drive through a car wash with

guide rails higher than 4 in/10 cm

to avoid damage to the body.

298

Online Edition for Part no. 01405A7B0F2 - II/23

Vehicle Care

MOBILITY

–

Observe the tire width of the guide

rail to avoid damage to tires and rims.

Thaw ice with de-icing spray; do not use an

ice scraper.

Fold in exterior mirrors to avoid dam-

age to the exterior mirrors.

After washing the vehicle

After washing the vehicle, apply the brakes

briefly to dry them; otherwise, braking ef-

fect can be reduced. The heat generated

during braking dries brake disks and brake

pads and protects them against corrosion.

With rod antenna: unscrew the rod

antenna to avoid rod antenna break-

age.

–

Deactivate the wiper and, if neces-

sary, rain sensor to avoid damage to

the window wiper system.

Completely remove all residues on the win-

dows to minimize loss of visibility due to

smearing and to reduce wiper noises and

wiper blade wear.

Driving into a car wash with a manual

transmission

In car washes, the vehicle must be able to

roll freely.

Vehicle care

Rolling or pushing the vehicle, refer to

page 117.

Vehicle care products

General information

MINI recommends using vehicle care and

cleaning agents from MINI. Suitable vehi-

cle care products are available from an au-

thorized service center or another qualified

service center or repair shop.

Driving into a car wash with a

Steptronic transmission

In car washes, the vehicle must be able to

roll freely.

Rolling or pushing the vehicle, refer to

page 119.

Some car washes do not permit persons in

the vehicle. The vehicle cannot be locked

from the outside when in selector lever po-

sition N. A signal is sounded when an at-

tempt is made to lock the vehicle.

Safety information

Warning

Cleaning agents can contain substances

that are dangerous and harmful to your

health. There is a risk of injury. When

cleaning the interior, open the doors or

windows. Only use products intended for

cleaning vehicles. Follow the instructions

on the packaging.

Driving out of a car wash

Ensure that the vehicle key is in the car.

Start the engine, refer to page 101.

Lights

Do not rub wet lights dry and do not use

abrasive or acidic cleaning agents or clean-

ing agents containing alcohol.

Vehicle paintwork

General information

Regular vehicle care contributes to driving

safety and value retention. Environmental

Soak areas that have been dirtied, for in-

stance from insects, with auto shampoo and

wash off with water.

299

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Vehicle Care

influences in areas with elevated air pollu-

tion or natural contaminants, such as tree

resin or pollen, can affect the vehicle paint-

work. Tailor the frequency and extent of the

vehicle care to these influences.

Immediately remove aggressive substances

such as sunscreen to prevent the synthetic

leather from being altered or discolored.

Upholstery material care

General information

Vacuum the cushions regularly with a vac-

uum cleaner.

Corrosive substances such as spilled fuel,

oil, grease or bird droppings, must be re-

moved immediately to prevent the finish

from being altered or discolored.

If upholstery is very contaminated, for in-

stance with beverage stains, use a soft

sponge or microfiber cloth with a suitable

interior cleaner.

Matte paintwork

Only use cleaning and care products suita-

ble for vehicles with matte paintwork.

Clean the cushions down to the seams using

large sweeping motions. Avoid rubbing the

material vigorously.

Leather care

Remove dust from the leather regularly, us-

ing a cloth or vacuum cleaner.

Safety information

Otherwise, particles of dust and road grime

chafe in pores and folds, and lead to heavy

abrasion and premature degradation of the

leather surface.

NOTICE

Open hook and loop fasteners on articles

of clothing can damage the seat covers

and other cloth upholstery in the vehicle.

There is a risk of damage to property. En-

sure that any Velcro® fasteners are closed.

To guard against discoloration, such as from

clothing, clean leather and provide leather

care roughly every two months.

Clean light-colored leather more frequently

because contamination on such surfaces is

substantially more visible.

Caring for special components

Light-alloy wheels

Use leather care products; otherwise, dirt

and grease will gradually break down the

protective coating of the leather surface.

When cleaning the vehicle, use only neutral

rim cleaners having a pH value from 5 to

9. Do not use abrasive cleaning agents or

steam cleaners above 140 ℉/60 ℃. Follow

the manufacturer's instructions.

Synthetic leather care

Clean synthetic leather regularly with a

damp microfiber cloth or vacuum cleaner.

Otherwise, dust and road grime particles

will rub into pores and folds, causing signif-

icant abrasion and premature degradation

of the surface.

Aggressive, acidic or alkaline cleaning

agents can destroy the protective coating

of adjacent components, such as the brake

disk.

In case of major soiling, use a moist soft

sponge or microfiber cloth with suitable in-

terior cleaners.

After cleaning, apply the brakes shortly to

dry them. The heat generated during brak-

ing dries brake disks and brake pads and

protects them against corrosion.

300

Online Edition for Part no. 01405A7B0F2 - II/23

Vehicle Care

Seat belts

MOBILITY

Chrome surfaces

Carefully clean components such as the ra-

diator grille or door handles with plenty

of water, if necessary, with auto shampoo

added, particularly when they have been ex-

posed to road salt.

Warning

Chemical solvent cleaners can destroy the

seat belt fabric. Missing protective effect

of the seat belts. There is a risk of injury

or danger to life. Use only a mild soap

solution for cleaning the seat belts.

Rubber components

Environmental influences can cause surface

contamination of rubber parts and a loss of

gloss. Use only water and suitable cleaning

agents for cleaning.

Dirty belt straps impede the reeling action

and thus have a negative impact on safety.

Use only a mild soap solution, with the seat

belts clipped into their buckles.

Treat especially worn rubber parts with rub-

ber care products at regular intervals. When

cleaning rubber seals, do not use any sili-

con-containing vehicle care products in or-

der to avoid damage or noises.

Seat belts should only be allowed to retract

if they are dry.

Carpets and floor mats

Wiper blades

The wiper blades are cleaned by using the

washer system.

Warning

Objects in the driver's footwell can limit

the pedal travel or block a depressed pedal.

There is a risk of accident. Stow objects in

the vehicle such that they are secured and

cannot enter into the driver's footwell. Use

floor mats that are suitable for the vehicle

and can be safely attached to the floor.

Do not use loose floor mats and do not

layer several floor mats. Make sure that

there is sufficient clearance for the pedals.

Ensure that the floor mats are securely fas-

tened again after they were removed, for

instance for cleaning.

Avoid cleaning the wiper blades manually,

as this may reduce wiper performance.

Fine wood parts

Clean fine wood facing and fine wood com-

ponents only with a moist rag. Then dry

with a soft cloth.

Plastic components

NOTICE

Solvent cleaners that contain alcohol or

solvents, such as lacquer thinners, cold

cleaning agents, fuel and such, can damage

plastic parts. There is a risk of damage

to property. Clean with a microfiber cloth.

Dampen the cloth lightly with water, if

needed.

Floor mats can be removed from the car's

interior for cleaning.

If the floor carpets are very contaminated,

clean with a microfiber cloth and water or

a textile cleaner. To prevent matting of the

carpet, rub back and forth in the driving

direction only.

Do not soak the headliner.

301

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY

Vehicle Care

Sensor/camera lenses

To clean sensors and camera lenses, use

a cloth moistened with a small amount of

glass detergent.

Displays/Screens/Projection screen

NOTICE

Chemical solvent cleaners, moisture or flu-

ids of any kind can damage the surface

of displays and screens. There is a risk of

damage to property. Clean with a clean,

antistatic microfiber cloth.

NOTICE

The surface of displays can be damaged

with improper cleaning. There is a risk of

damage to property. Avoid pressure that

is too high and do not use any scratching

materials.

Use a dry, clean antistatic microfiber cloth.

For stubborn soiling on the projection

screen of the Head-up display, dampen the

microfiber cloth with ethyl alcohol. Projec-

tion screen, refer to page 142.

Taking the vehicle out of service

When the vehicle is shut down for longer

than three months, special measures must

be taken. For more information, contact an

authorized service center or another quali-

fied service center or repair shop.

302

Online Edition for Part no. 01405A7B0F2 - II/23

Vehicle Care

MOBILITY

303

Online Edition for Part no. 01405A7B0F2 - II/23

MOBILITY for Your Mini Clubman SUV Second Generation (2015-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals