2010-2017 Nissan Leaf 4 Door Safety-Seats, seat belts and supplemental restraint system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Safety-Seats, seat belts and supplemental restraint system for Your Nissan Leaf 4 Door First Generation (2010-2017)

1 Safety–Seats, seat belts and  
supplemental restraint system  
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2  
Front seats . . . . . . . . . . . . . . . . . . . . . . . . .1-3  
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . .1-4  
Head restraints/headrests . . . . . . . . . . . . . . . .1-5  
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . .1-8  
Precautions on seat belt usage . . . . . . . . . . . . .1-8  
Pregnant women . . . . . . . . . . . . . . . . . . . .1-11  
Injured persons . . . . . . . . . . . . . . . . . . . . .1-11  
Three-point type seat belt with retractor . . . . . . .1-11  
Seat belt extenders . . . . . . . . . . . . . . . . . . .1-15  
Seat belt maintenance . . . . . . . . . . . . . . . . .1-15  
Child safety. . . . . . . . . . . . . . . . . . . . . . . . . .1-15  
Infants. . . . . . . . . . . . . . . . . . . . . . . . . . .1-16  
Small children . . . . . . . . . . . . . . . . . . . . . .1-16  
Larger children. . . . . . . . . . . . . . . . . . . . . .1-16  
Child restraints. . . . . . . . . . . . . . . . . . . . . . . .1-18  
Precautions on child restraints . . . . . . . . . . . .1-18  
Rear-facing child restraint installation using latch. .1-22  
Rear-facing child restraint installation using  
Forward-facing child restraint installation using  
latch . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-27  
Forward-facing child restraint installation using  
the seat belts. . . . . . . . . . . . . . . . . . . . . . .1-29  
Installing top tether strap . . . . . . . . . . . . . . . .1-32  
Booster seats . . . . . . . . . . . . . . . . . . . . . . . .1-33  
Precautions on booster seats . . . . . . . . . . . . .1-33  
Booster seat installation . . . . . . . . . . . . . . . .1-35  
Supplemental restraint system. . . . . . . . . . . . . . .1-36  
Precautions on supplemental restraint system . . .1-36  
NISSAN Advanced Air Bag System (front seats) . .1-42  
Front seat-mounted side-impact supplemental  
air bag and roof-mounted curtain side-impact  
supplemental air bag systems . . . . . . . . . . . . .1-47  
Seat belts with pretensioners (front seats). . . . . .1-49  
Supplemental air bag warning labels . . . . . . . . .1-50  
Supplemental air bag warning light . . . . . . . . . .1-50  
Repair and replacement procedure . . . . . . . . . .1-51  
the seat belts. . . . . . . . . . . . . . . . . . . . . . .1-24  
SEATS  
•
The seatback should not be reclined  
any more than needed for comfort.  
Seat belts are most effective when the  
passenger sits well back and straight  
up in the seat. If the seatback is re-  
clined, the risk of sliding under the lap  
belt and being injured is increased.  
CAUTION  
When adjusting the seat positions, be  
sure not to contact any moving parts to  
avoid possible injuries and/or damage.  
•
For the most effective protection when  
the vehicle is in motion, the seat  
should be upright. Always sit well back  
in the seat with both feet on the floor  
and adjust the seat properly. See “Pre-  
cautions on seat belt usage” in this  
section.  
WARNING  
•
Do not ride in a moving vehicle when  
the seatback is reclined. This can be  
dangerous. The shoulder belt will not  
be against your body. In an accident,  
you could be thrown into it and receive  
neck or other serious injuries. You  
could also slide under the lap belt and  
receive serious internal injuries.  
•
•
After adjustment, gently rock in the  
seat to make sure it is securely locked.  
Do not leave children unattended in-  
side the vehicle. They could unknow-  
ingly activate switches or controls. Un-  
attended children could become  
involved in serious accidents.  
1-2 Safety–Seats, seat belts and supplemental restraint system  
Reclining:  
Seat lifter (for driver’s seat):  
FRONT SEATS  
To recline the seatback, pull the lever up and lean  
back. To bring the seatback forward, pull the lever  
up and lean your body forward. Release the lever  
to lock the seatback in position.  
Pull up or push down the adjusting lever to adjust  
the seat height to the preferred position.  
Front manual seat adjustment  
Forward and backward:  
Pull the bar up and hold it while sliding the seat  
forward or backward to the preferred position.  
Release the bar to lock the seat in position.  
The reclining feature allows adjustment of the  
seatback for occupants of different sizes for  
added comfort and to help obtain proper seat  
belt fit. See “Precautions on seat belt usage” in  
this section. Also, the seatback can be reclined to  
allow occupants to rest when the vehicle is  
stopped and the vehicle is in the P (Park) position  
or N (Neutral) position with the parking brake  
applied.  
Safety–Seats, seat belts and supplemental restraint system 1-3  
•
•
Properly secure all cargo with ropes or  
straps to help prevent it from sliding or  
shifting. Do not place cargo higher  
than the seatbacks. In a sudden stop or  
collision, unsecured cargo could cause  
personal injury.  
When returning the seatbacks to the  
upright position, be certain they are  
completely secured in the latched po-  
sition. If they are not completely se-  
cured, passengers may be injured in an  
accident or sudden stop.  
REAR SEATS  
Folding  
WARNING  
•
•
Do not fold down the rear seats when  
occupants are in the rear seat area or  
any objects are on the rear seats.  
Never allow anyone to ride in the cargo  
area or on the rear seats when they are  
in the folded-down position. Use of  
these areas by passengers without  
proper restraints could result in seri-  
ous injury in an accident or sudden  
stop.  
Before folding the rear seats:  
• Secure the seat belts on the seat belt hooks  
located on the side wall. See “Seat belt hooks”  
in this section.  
To fold down the seatback, pull the release knob.  
To return the seatback to the seating position, lift  
up each seatback and push it to the upright  
position until it is latched.  
1-4 Safety–Seats, seat belts and supplemental restraint system  
• The non-adjustable head restraints/headrests  
have a single locking notch to secure them to  
the seat frame.  
HEAD RESTRAINTS/HEADRESTS  
WARNING  
• Proper Adjustment:  
Head restraint/headrest supplement the  
other vehicle safety systems. They may  
provide additional protection against in-  
jury in certain rear end collisions. Adjust-  
able head restraints/headrests must be  
adjusted properly, as specified in this  
section. Check the adjustment after  
someone else uses the seat. Do not at-  
tach anything to the head restraint/  
headrest stalks or remove the head  
restraints/headrests. Do not use the seat  
if the head restraint/headrest has been  
removed. If the head restraint/headrest  
was removed, reinstall and properly ad-  
just the head restraint/headrest before  
an occupant uses the seating position.  
Failure to follow these instructions can  
reduce the effectiveness of the head  
restraint/headrest. This may increase the  
risk of serious injury or death in a colli-  
sion.  
– For the adjustable type, align the head  
restraint/headrest so the center of your ear  
is approximately level with the center of the  
head restraint/headrest.  
– If your ear position is still higher than the  
recommended alignment, place the head  
restraint/headrest at the highest position.  
• If the head restraint/headrest has been re-  
moved, ensure that it is reinstalled and locked in  
place before riding in that designated seating  
position.  
The illustration shows the seating positions  
equipped with a head restraint/headrest.  
Indicates the seating position is equipped  
with a head restraint.  
+ Indicates the seating position is not equipped  
with a head restraint or headrest (if applicable).  
• Your vehicle is equipped with a head restraint/  
headrest that may be integrated, adjustable or  
non-adjustable.  
• Adjustable head restraints/headrests have mul-  
tiple notches along the stalks to lock them in a  
desired adjustment position.  
Safety–Seats, seat belts and supplemental restraint system 1-5  
Adjustable head restraint/headrest  
components  
1. Removable head restraint/headrest  
2. Multiple notches  
3. Lock knob  
Non-adjustable head restraint/  
headrest components  
1. Removable head restraint/headrest  
2. Single notch  
Adjust  
For adjustable head restraint/headrest  
Adjust the head restraint/headrest so the center  
is level with the center of your ears. If your ear  
position is still higher than the recommended  
alignment, place the head restraint/headrest at  
the highest position.  
3. Lock knob  
4. Stalks  
4. Stalks  
For non-adjustable head restraint/headrest  
1-6 Safety–Seats, seat belts and supplemental restraint system  
Make sure the head restraint/headrest is posi-  
tioned so the lock knob is engaged in the notch  
before riding in that designated seating position.  
Remove  
Install  
Use the following procedure to remove the head  
restraint/headrest.  
1. Align the head restraint/headrest stalks with  
the holes in the seat. Make sure the head  
restraint/headrest is facing the correct direc-  
1. Pull the head restraint/headrest up to the  
highest position.  
1
tion. The stalk with the notch (notches)  
᭺
must be installed in the hole with the lock  
2. Push and hold the lock knob.  
2
knob  
.
᭺
3. Remove the head restraint/headrest from the  
seat.  
2. Push and hold the lock knob and push the  
head restraint/headrest down.  
4. Store the head restraint/headrest properly in  
a secure place so it is not loose in the vehicle.  
3. Properly adjust the head restraint/headrest  
before an occupant uses the seating position.  
5. Reinstall and properly adjust the head  
restraint/headrest before an occupant uses  
the seating position.  
Safety–Seats, seat belts and supplemental restraint system 1-7  
SEAT BELTS  
PRECAUTIONS ON SEAT BELT  
USAGE  
If you are wearing your seat belt properly ad-  
justed, and you are sitting upright and well back  
in your seat with both feet on the floor, your  
chances of being injured or killed in an accident  
and/or the severity of injury may be greatly re-  
duced. NISSAN strongly encourages you and all  
of your passengers to buckle up every time you  
drive, even if your seating position includes a  
supplemental air bag.  
Most U.S. states and Canadian provinces or  
territories specify that seat belts be worn at  
all times when a vehicle is being driven.  
Raise  
Lower  
To raise the head restraint/headrest, pull it up.  
To lower, push and hold the lock knob and push  
the head restraint/headrest down  
Make sure the head restraint/headrest is posi-  
tioned so the lock knob is engaged in the notch  
before riding in that designated seating position.  
Make sure the head restraint/headrest is posi-  
tioned so the lock knob is engaged in the notch  
before riding in that designated seating position.  
1-8 Safety–Seats, seat belts and supplemental restraint system  
Safety–Seats, seat belts and supplemental restraint system 1-9  
•
Do not wear the seat belt inside out or  
twisted. Doing so may reduce its effec-  
tiveness.  
Do not allow more than one person to  
use the same seat belt.  
Never carry more people in the vehicle  
than there are seat belts.  
If the seat belt warning light glows  
continuously while the power switch is  
turned ON with all doors closed and all  
seat belts fastened, it may indicate a  
malfunction in the system. Have the  
system checked by a NISSAN certified  
LEAF dealer.  
No changes should be made to the  
seat belt system. For example, do not  
modify the seat belt, add material, or  
install devices that may change the  
seat belt routing or tension. Doing so  
may affect the operation of the seat  
belt system. Modifying or tampering  
with the seat belt system may result in  
serious personal injury.  
•
•
Removal and installation of the pre-  
tensioner system components should  
be done by a NISSAN certified LEAF  
dealer.  
WARNING  
•
•
Every person who drives or rides in this  
vehicle should use a seat belt at all  
times. Children should be properly re-  
strained in the rear seat and, if appro-  
priate, in a child restraint.  
The seat belt should be properly ad-  
justed to a snug fit. Failure to do so  
may reduce the effectiveness of the  
entire restraint system and increase  
the chance or severity of injury in an  
accident. Serious injury or death can  
occur if the seat belt is not worn prop-  
erly.  
Always route the shoulder belt over  
your shoulder and across your chest.  
Never put the belt behind your back,  
under your arm or across your neck.  
The belt should be away from your face  
and neck, but not falling off your  
shoulder.  
Position the lap belt as low and snug  
as possible AROUND THE HIPS, NOT  
THE WAIST. A lap belt worn too high  
could increase the risk of internal inju-  
ries in an accident.  
•
•
•
All seat belt assemblies, including re-  
tractors and attaching hardware,  
should be inspected after any collision  
by a NISSAN certified LEAF dealer.  
NISSAN recommends that all seat belt  
assemblies in use during a collision be  
replaced unless the collision was mi-  
nor and the belts show no damage and  
continue to operate properly. Seat belt  
assemblies not in use during a colli-  
sion should also be inspected and re-  
placed if either damage or improper  
operation is noted.  
All child restraints and attaching hard-  
ware should be inspected after any  
collision. Always follow the restraint  
manufacturer’s inspection instructions  
and replacement recommendations.  
The child restraints should be replaced  
if they are damaged.  
•
•
•
•
•
•
Once a seat belt pretensioner has ac-  
tivated, it cannot be reused and must  
be replaced together with the retrac-  
tor. See  
dealer.  
a
NISSAN certified LEAF  
Be sure the seat belt tongue is se-  
curely fastened to the proper buckle.  
1-10 Safety–Seats, seat belts and supplemental restraint system  
PREGNANT WOMEN  
•
Do not ride in a moving vehicle when  
the seatback is reclined. This can be  
dangerous. The shoulder belt will not  
be against your body. In an accident,  
you could be thrown into it and receive  
neck or other serious injuries. You  
could also slide under the lap belt and  
receive serious internal injuries.  
For the most effective protection when  
the vehicle is in motion, the seat  
should be upright. Always sit well back  
in the seat with both feet on the floor  
and adjust the seat belt properly.  
Do not allow children to play with the  
seat belts. Most seating positions are  
equipped with Automatic Locking Re-  
tractor (ALR) mode seat belts. If the  
seat belt becomes wrapped around a  
child’s neck with the ALR mode acti-  
vated, the child can be seriously in-  
jured or killed if the seat belt retracts  
and becomes tight. This can occur  
even if the vehicle is parked. Unbuckle  
the seat belt to release the child. If the  
seat belt can not be unbuckled or is  
already unbuckled, release the child by  
cutting the seat belt with a suitable  
tool (such as a knife or scissors) to  
release the seat belt.  
NISSAN recommends that pregnant women use  
seat belts. The seat belt should be worn snug,  
and always position the lap belt as low as pos-  
sible around the hips, not the waist. Place the  
shoulder belt over your shoulder and across your  
chest. Never put the lap/shoulder belt over your  
abdominal area. Contact your doctor for specific  
recommendations.  
•
•
INJURED PERSONS  
NISSAN recommends that injured persons use  
seat belts, depending on the injury. Check with  
your doctor for specific recommendations.  
Fastening the seat belts  
THREE-POINT TYPE SEAT BELT  
WITH RETRACTOR  
1. Adjust the seat. See “Seats” in this section.  
2. Slowly pull the seat belt out of the retractor  
and insert the tongue into the buckle until you  
hear and feel the latch engage.  
WARNING  
• The retractor is designed to lock during  
a sudden stop or on impact. A slow  
pulling motion permits the belt to move  
and allows you some freedom of move-  
ment in the seat.  
•
Every person who drives or rides in this  
vehicle should use a seat belt at all  
times.  
Safety–Seats, seat belts and supplemental restraint system 1-11  
• If the seat belt cannot be pulled from its  
fully retracted position, firmly pull the  
belt and release it. Then smoothly pull  
the belt out of the retractor.  
the driver and passengers some freedom of  
movement in the seat. The ELR locks the seat belt  
when the vehicle slows down rapidly or during  
certain impacts.  
The Automatic Locking Retractor (ALR) mode  
(child restraint mode) locks the seat belt for child  
restraint installation.  
When ALR mode is activated the seat belt cannot  
be extended again until the seat belt tongue is  
detached from the buckle and fully retracted. The  
seat belt returns to the ELR mode after the seat  
belt fully retracts. For additional information, see  
“Child restraints” in this section.  
3. Position the lap belt portion low and snug  
on the hips as shown.  
The ALR mode should be used only for  
child restraint installation. During normal  
seat belt use by an occupant, the ALR mode  
should not be activated. If it is activated, it  
may cause uncomfortable seat belt ten-  
sion.  
4. Pull the shoulder belt portion toward the re-  
tractor to take up extra slack. Be sure the  
shoulder belt is routed over your shoulder and  
across your chest.  
The front passenger seat and the rear seating  
positions three-point seat belts have two modes  
of operation:  
WARNING  
When fastening the seat belts, be certain  
that seatbacks are completely secured in  
the latched position. If they are not com-  
pletely secured, passengers may be in-  
jured in an accident or sudden stop.  
• Emergency Locking Retractor (ELR)  
• Automatic Locking Retractor (ALR)  
The Emergency Locking Retractor (ELR) mode  
allows the seat belt to extend and retract to allow  
1-12 Safety–Seats, seat belts and supplemental restraint system  
Checking seat belt operation  
Seat belt retractors are designed to lock seat belt  
movement by two separate methods:  
• When the belt is pulled quickly from the retrac-  
tor.  
• When the vehicle slows down rapidly.  
To increase your confidence in the seat belts,  
check the operation as follows:  
• Grasp the shoulder belt and pull forward  
quickly. The retractor should lock and restrict  
further belt movement.  
If the retractor does not lock during this check or  
if you have any questions about seat belt opera-  
tion, see a NISSAN certified LEAF dealer.  
The shoulder belt anchor height should be ad-  
justed to the position that is best for you. See  
“Precautions on seat belt usage” in this section.  
Unfastening the seat belts  
To unfasten the seat belt, push the button on the  
buckle. The seat belt automatically retracts.  
Shoulder belt height adjustment (for  
front seats)  
1
To adjust, pull the adjustment button , and then  
᭺
move the shoulder belt anchor to the preferred  
2
position  
so that the belt passes over the  
᭺
center of the shoulder. The belt should be away  
from your face and neck, but not falling off of your  
shoulder. Release the adjustment button to lock  
the shoulder belt anchor into position.  
Safety–Seats, seat belts and supplemental restraint system 1-13  
WARNING  
•
•
After adjustment, release the adjust-  
ment button and then try to move the  
shoulder belt anchor up and down to  
make sure that it is securely fixed in  
position.  
The shoulder belt anchor height  
should be adjusted to the position that  
is best for you. Failure to do so may  
reduce the effectiveness of the entire  
restraint system and increase the  
chance or severity of injury in an acci-  
dent.  
Seat belt hooks  
Center of rear seat  
When the rear seat belts are not in use and when  
folding down the rear seats, hook the rear outer  
seat belts on the seat belt hooks.  
Selecting correct set of seat belts:  
The center seat belt buckle is identified by the  
A
CENTER mark  
. The center seat belt tongue  
᭺
can be fastened only into the center seat belt  
buckle.  
1-14 Safety–Seats, seat belts and supplemental restraint system  
CHILD SAFETY  
SEAT BELT EXTENDERS  
SEAT BELT MAINTENANCE  
WARNING  
• To clean the seat belt webbing, apply a mild  
soap solution or any solution recommended for  
cleaning upholstery or carpets. Then wipe with  
a cloth and allow the seat belts to dry in the  
shade. Do not allow the seat belts to retract until  
they are completely dry.  
If, because of body size or driving position, it is  
not possible to properly fit the lap-shoulder belt  
and fasten it, an extender that is compatible with  
the installed seat belts is available that can be  
purchased. The extender adds approximately 8 in  
(200 mm) of length and may be used for either  
the driver or front passenger seating position.  
See a NISSAN certified LEAF dealer for assis-  
tance with purchasing an extender if an extender  
is required.  
Do not allow children to play with the  
seat belts. Most seating positions are  
equipped with Automatic Locking Retrac-  
tor (ALR) mode seat belts. If the seat belt  
becomes wrapped around a child’s neck  
with the ALR mode activated, the child  
can be seriously injured or killed if the  
seat belt retracts and becomes tight. This  
can occur even if the vehicle is parked.  
Unbuckle the seat belt to release the  
child. If the seat belt can not be unbuck-  
led or is already unbuckled, release the  
child by cutting the seat belt with a suit-  
able tool (such as a knife or scissors) to  
release the seat belt.  
• If dirt builds up in the shoulder belt guide  
of the seat belt anchors, the seat belts may  
retract slowly. Wipe the shoulder belt guide with  
a clean, dry cloth.  
• Periodically check to see that the seat belt  
and the metal components, such as buckles,  
tongues, retractors, flexible wires and anchors,  
work properly. If loose parts, deterioration, cuts  
or other damage on the webbing is found, the  
entire seat belt assembly should be replaced.  
WARNING  
•
•
•
Only NISSAN seat belt extenders,  
made by the same company which  
made the original equipment seat  
belts, should be used with NISSAN  
seat belts.  
Adults and children who can use the  
standard seat belt should not use an  
extender. Such unnecessary use could  
result in serious personal injury in the  
event of an accident.  
Never use seat belt extenders to install  
child restraints. If the child restraint is  
not secured properly, the child could  
be seriously injured in a collision or a  
sudden stop.  
Children need adults to help protect them.  
They need to be properly restrained.  
In addition to the general information in this  
manual, child safety information is available from  
many other sources, including doctors, teachers,  
government traffic safety offices, and community  
organizations. Every child is different, so be sure  
to learn the best way to transport your child.  
Safety–Seats, seat belts and supplemental restraint system 1-15  
There are three basic types of child restraint  
systems:  
for infants and small children. See “Child re-  
straints” in this section.  
SMALL CHILDREN  
Children that are over 1 year old and weigh at  
least 20 lbs (9 kg) should remain in a rear-facing  
child restraint as long as possible up to the height  
or weight limit of the child restraint. Children who  
outgrow the height or weight limit of the rear-  
facing child restraint and are at least 1 year old  
should be secured in a forward-facing child re-  
straint with a harness. Refer to the manufactur-  
er’s instructions for minimum and maximum  
weight and height recommendations. NISSAN  
recommends that small children be placed in  
child restraints that comply with Federal Motor  
Vehicle Safety Standards or Canadian Motor Ve-  
hicle Safety Standards. You should choose a  
child restraint that fits your vehicle and always  
follow the manufacturer’s instructions for instal-  
lation and use.  
• Rear-facing child restraint  
• Forward-facing child restraint  
• Booster seat  
A child restraint may be secured in the vehicle by  
using either the LATCH (Lower Anchor and Teth-  
ers for Children) system or with the vehicle seat  
belt. For more information, see “Child restraints”  
in this section.  
The proper restraint depends on the child’s size.  
Generally, infants up to about 1 year and less  
than 20 lb (9 kg) should be placed in rear-facing  
child restraints. Forward-facing child restraints  
are available for children who outgrow rear-  
facing child restraints and are at least 1 year old.  
Booster seats are used to help position a vehicle  
lap/shoulder belt on a child who can no longer  
use a forward-facing child restraint.  
NISSAN recommends that all pre-teens  
and children be restrained in the rear seat.  
According to accident statistics, children  
are safer when properly restrained in the  
rear seat than in the front seat.  
This is especially important because your  
vehicle has a supplemental restraint sys-  
tem (air bag system) for the front passen-  
ger. See “Supplemental restraint system”  
in this section.  
WARNING  
Infants and children need special protec-  
tion. The vehicle’s seat belts may not fit  
them properly. The shoulder belt may  
come too close to the face or neck. The  
lap belt may not fit over their small hip  
bones. In an accident, an improperly fit-  
ting seat belt could cause serious or fatal  
injury. Always use appropriate child re-  
straints.  
INFANTS  
LARGER CHILDREN  
Infants up to at least 1 year old should be placed  
in a rear-facing child restraint. NISSAN recom-  
mends that infants be placed in child restraints  
that comply with Federal Motor Vehicle Safety  
Standards or Canadian Motor Vehicle Safety  
Standards. You should choose a child restraint  
that fits your vehicle and always follow the manu-  
facturer’s instructions for installation and use.  
Children should remain in a forward-facing child  
restraint with a harness until they reach the maxi-  
mum height or weight limit allowed by the child  
restraint manufacturer.  
Once a child outgrows the height or weight limit  
of the harness-equipped forward-facing child re-  
straint, NISSAN recommends that the child be  
All U.S. states and Canadian provinces or territo-  
ries require the use of approved child restraints  
1-16 Safety–Seats, seat belts and supplemental restraint system  
placed in a commercially available booster seat to  
obtain proper seat belt fit. For a seat belt to fit  
properly, the booster seat should raise the child  
so that the shoulder belt is properly positioned  
across the chest and the top, middle portion of  
the shoulder. The shoulder belt should not cross  
the neck or face and should not fall off the shoul-  
der. The lap belt should lie snugly across the  
lower hips or upper thighs, not the abdomen. A  
booster seat can only be used in seating posi-  
tions that have a three-point type seat belt. The  
booster seat should fit the vehicle seat and have  
a label certifying that it complies with Federal  
Motor Vehicle Safety Standards or Canadian Mo-  
tor Vehicle Safety Standards. Once the child has  
grown so the shoulder belt is no longer on or near  
the face and neck and the lap belt can be posi-  
tioned properly across the lower hips or upper  
thighs use the seat belt without the booster seat.  
WARNING  
Never let a child stand or kneel on any  
seat and do not allow a child in the cargo  
areas. The child could be seriously in-  
jured or killed in an accident or sudden  
stop.  
Safety–Seats, seat belts and supplemental restraint system 1-17  
CHILD RESTRAINTS  
PRECAUTIONS ON CHILD  
RESTRAINTS  
–
–
NISSAN recommends that all child  
restraints be installed in the rear  
seat. Studies show that children are  
safer when properly restrained in  
the rear seat than in the front seat. If  
you must install a forward-facing  
child restraint in the front seat, see  
“Forward-facing child restraint in-  
stallation using the seat belts” in  
this section.  
Even with the NISSAN Advanced Air  
Bag System, never install a rear-  
facing child restraint in the front  
seat. An inflating air bag could seri-  
ously injure or kill a child. A rear-  
facing child restraint must only be  
used in the rear seat.  
A child restraint with a top tether  
strap should not be used in the front  
passenger seat.  
Keep seatbacks as upright as pos-  
sible after fitting the child restraint.  
Infants and children should always  
be placed in an appropriate child  
restraint while in the vehicle.  
–
–
WARNING  
•
Failure to follow the warnings and in-  
structions for proper use and installa-  
tion of child restraints could result in  
serious injury or death of a child or  
other passengers in a sudden stop or  
collision:  
•
When the child restraint is not in use,  
keep it secured with the LATCH system  
or a seat belt. In a sudden stop or  
collision, loose objects can injure oc-  
cupants or damage the vehicle.  
–
–
–
–
–
The child restraint must be used and  
installed properly. Always follow all  
of the child restraint manufacturer’s  
instructions for installation and use.  
Infants and children should never be  
held on anyone’s lap. Even the  
strongest adult cannot resist the  
forces of a collision.  
CAUTION  
Be sure to purchase a child restraint  
that will fit the child and vehicle.  
Some child restraints may not fit  
properly in your vehicle.  
A child restraint in a closed vehicle can  
become very hot. Check the seating sur-  
face and buckles before placing a child in  
the child restraint.  
Do not put a seat belt around both a  
child and another passenger.  
–
–
Child restraint anchor points are de-  
signed to withstand loads from child  
restraints that are properly fitted.  
Never use the anchor points for  
adult seat belts or harnesses.  
This vehicle is equipped with a universal child  
restraint anchor system, referred to as the LATCH  
(Lower Anchors and Tethers for CHildren) sys-  
tem. Some child restraints include rigid or  
webbing-mounted attachments that can be con-  
nected to these anchors.  
1-18 Safety–Seats, seat belts and supplemental restraint system  
For details, see “Lower Anchors and Tethers for  
CHildren System (LATCH)” in this section.  
• If the combined weight of the child and child  
restraint is greater than 65 lbs, (29.5 kg) use the  
vehicle’s seat belt (not the lower anchors) to  
install the child restraint.  
If you do not have a LATCH compatible child  
restraint, the vehicle seat belts can be used.  
• Be sure to follow the child restraint manufactur-  
er’s instructions for installation.  
Several manufacturers offer child restraints for  
infants and small children of various sizes. When  
selecting any child restraint, keep the following  
points in mind:  
All U.S. states and Canadian provinces or  
territories require that infants and small  
children be restrained in an approved child  
restraint at all times while the vehicle is  
being operated. Canadian law requires the  
top tether strap on forward-facing child re-  
straints be secured to the designated an-  
chor point on the vehicle.  
• Choose only a restraint with a label certifying  
that it complies with Federal Motor Vehicle  
Safety Standard 213 or Canadian Motor Ve-  
hicle Safety Standard 213.  
• Check the child restraint in your vehicle to be  
sure it is compatible with the vehicle’s seat and  
seat belt system.  
Lower Anchors and Tethers for  
CHildren System (LATCH)  
• If the child restraint is compatible with your  
vehicle, place your child in the child restraint  
and check the various adjustments to be sure  
the child restraint is compatible with your child.  
Choose a child restraint that is designed for  
your child’s height and weight. Always follow all  
recommended procedures.  
Your vehicle is equipped with special anchor  
points that are used with Lower Anchors and  
Tethers for CHildren System (LATCH) compat-  
ible child restraints. This system may also be  
referred to as the ISOFIX or ISOFIX compatible  
system. With this system, you do not have to use  
a vehicle seat belt to secure the child restraint  
unless the combined weight of the child and child  
restraint exceeds 65 lbs (29.5 kg). If the com-  
bined weight of the child and child restraint is  
greater than 65 lbs, (29.5 kg) use the vehicle’s  
• If the combined weight of the child and child  
restraint is less than 65 lbs (29.5 kg), you may  
use either the LATCH anchors or the seat belt to  
install the child restraint (not both at the same  
time).  
Safety–Seats, seat belts and supplemental restraint system 1-19  
seat belt (not the lower anchors) to install the  
child restraint. Be sure to follow the child restraint  
manufacturer’s instructions for installation.  
•
Child restraint anchorages are de-  
signed to withstand only those loads  
imposed by correctly fitted child re-  
straints. Under no circumstances are  
they to be used to attach adult seat  
belts, or other items or equipment to  
the vehicle. Doing so could damage  
the child restraint anchorages. The  
child restraint will not be properly in-  
stalled using the damaged anchorage,  
and a child could be seriously injured  
or killed in a collision.  
LATCH lower anchor  
WARNING  
Failure to follow the warnings and in-  
structions for proper use and installation  
of child restraints could result in serious  
injury or death of a child or other passen-  
gers in a sudden stop or collision:  
•
Attach LATCH system compatible child  
restraints only at the locations shown  
in the illustration.  
LATCH lower anchor location  
•
Inspect the lower anchors by inserting  
your fingers into the lower anchor  
area. Feel to make sure there are no  
obstructions over the anchors such as  
seat belt webbing or seat cushion ma-  
terial. The child restraint will not be  
secured properly if the lower anchors  
are obstructed.  
LATCH lower anchor location  
The LATCH anchors are located at the rear of the  
seat cushion near the seatback. A label is at-  
tached to the seatback to help you locate the  
LATCH anchors.  
1-20 Safety–Seats, seat belts and supplemental restraint system  
Top tether anchor  
WARNING  
If the tonneau cover contacts the top  
•
tether strap when it is attached to the  
top tether anchor, remove the tonneau  
cover from the vehicle or secure it on  
the cargo floor below its attachment  
location. If the tonneau cover is not  
removed, it may damage the top tether  
strap during a collision. Your child  
could be seriously injured or killed in a  
collision if the child restraint top tether  
strap is damaged.  
Do not allow cargo to contact the top  
tether strap when it is attached to the  
top tether anchor. Properly secure the  
cargo so it does not contact the top  
tether strap. Cargo that is not properly  
secured or that contacts the top tether  
strap may damage the top tether strap  
during a collision. Your child could be  
seriously injured or killed in a collision  
if the child restraint top tether strap is  
damaged.  
LATCH webbing-mounted attachment  
Installing child restraint LATCH lower  
anchor attachments  
LATCH rigid-mounted attachment  
When installing a child restraint, carefully read  
and follow the instructions in this manual and  
those supplied with the child restraint.  
•
LATCH compatible child restraints include two  
rigid or webbing-mounted attachments that can  
be connected to two anchors located at certain  
seating positions in your vehicle. With this sys-  
tem, you do not have to use a vehicle seat belt to  
secure the child restraint. Check your child re-  
straint for a label stating that it is compatible with  
the LATCH system. This information may also be  
in the instructions provided by the child restraint  
manufacturer.  
Safety–Seats, seat belts and supplemental restraint system 1-21  
REAR-FACING CHILD RESTRAINT  
INSTALLATION USING LATCH  
Refer to all Warnings and Cautions in “Child  
safety” and “Child restraints” in this section be-  
fore installing a child restraint.  
•
Child restraint anchorages are de-  
signed to withstand only those loads  
imposed by correctly fitted child re-  
straints. Under no circumstances are  
they to be used to attach adult seat  
belts, or other items or equipment to  
the vehicle. Doing so could damage  
the child restraint anchorages. The  
child restraint will not be properly in-  
stalled using the damaged anchorage,  
and a child could be seriously injured  
or killed in a collision.  
NISSAN does not recommend the use of the  
lower anchors if the combined weight of the child  
and the child restraint exceeds 65 lbs (29.5 kg). If  
the combined weight of the child and the child  
restraint is greater than 65 lbs, (29.5 kg) use the  
vehicle’s seat belt (not the lower anchors) to  
install the child restraint. Be sure to follow the  
child restraint manufacturer’s instructions for in-  
stallation.  
Top tether anchor point locations:  
Anchor points are located on the back side of the  
seatbacks.  
Follow these steps to install a rear-facing child  
restraint using the LATCH system  
The child restraint top tether strap must be used  
when installing child restraints with the LATCH  
lower anchor attachments or seat belts.  
1. Position the child restraint on the seat. Always  
follow the child restraint manufacturer’s  
instructions.  
If you have any questions when installing a  
top tether strap, consult your NISSAN cer-  
tified LEAF dealer for details.  
1-22 Safety–Seats, seat belts and supplemental restraint system  
Rear-facing (webbing-mounted) — step 2  
2. Secure the child restraint anchor attachments  
to the LATCH lower anchors. Check to make  
sure that the LATCH attachment is properly  
attached to the lower anchors.  
Rear-facing (rigid-mounted) — step 2  
3. For child restraints that are equipped with  
webbing-mounted attachments, remove any  
additional slack from the anchor attachments.  
Press downward and rearward firmly in the  
center of the child restraint with your hand to  
compress the vehicle seat cushion and seat-  
back while tightening the webbing of the an-  
chor attachments.  
Rear-facing — step 3  
4. After attaching the child restraint, test it be-  
fore you place the child in it. Push it from side  
to side while holding the seat near the LATCH  
attachment path. The child restraint should  
not move more than 1 inch (25 mm) from side  
to side. Try to tug it forward and check to see  
if the LATCH attachment holds the restraint in  
place. If the restraint is not secure, tighten the  
LATCH attachment as necessary, or put the  
restraint on another seat and test it again. You  
may need to try a different child restraint. Not  
all child restraints fit in all types of vehicles.  
Safety–Seats, seat belts and supplemental restraint system 1-23  
Refer to all Warnings and Cautions in “Child  
safety” and “Child restraints” in this section be-  
fore installing a child restraint.  
NISSAN does not recommend the use of the  
lower anchors if the combined weight of the child  
and the child restraint exceeds 65 lbs (29.5 kg). If  
the combined weight of the child and the child  
restraint is greater than 65 lbs, (29.5 kg) use the  
vehicle’s seat belt (not the lower anchors) to  
install the child restraint. Be sure to follow the  
child restraint manufacturer’s instructions for in-  
stallation.  
Rear-facing — step 4  
REAR-FACING CHILD RESTRAINT  
INSTALLATION USING THE SEAT  
BELTS  
5. Check to make sure that the child restraint is  
properly secured prior to each use. If the child  
restraint is loose, repeat steps 2 through 4.  
WARNING  
The three-point seat belt with Automatic  
Locking Retractor (ALR) must be used  
when installing a child restraint. Failure  
to use the ALR mode will result in the  
child restraint not being properly se-  
cured. The restraint could tip over or be  
loose and cause injury to a child in a  
sudden stop or collision.  
1-24 Safety–Seats, seat belts and supplemental restraint system  
Rear facing - step 1  
Follow these steps to install a rear-facing child  
restraint using the vehicle seat belt in the rear  
seat:  
Rear-facing — step 2  
Rear-facing — step 3  
2. Route the seat belt tongue through the child  
restraint and insert it into the buckle until you  
hear and feel the latch engage. Be sure to  
follow the child restraint manufacturer’s in-  
structions for belt routing.  
3. Pull the shoulder belt until the belt is fully  
extended. At this time, the seat belt retractor  
is in the Automatic Locking Retractor (ALR)  
mode (child restraint mode). It reverts to the  
Emergency Locking Retractor (ELR) mode  
when the seat belt is fully retracted.  
1. Child restraints for infants must be used  
in the rear-facing direction and there-  
fore must not be used in the front seat.  
Position the child restraint on the seat. Always  
follow  
the  
restraint  
manufacturer’s  
instructions.  
Safety–Seats, seat belts and supplemental restraint system 1-25  
Rear-facing — step 4  
Rear-facing — step 5  
Rear-facing — step 6  
4. Allow the seat belt to retract. Pull up on the  
shoulder belt to remove any slack in the belt.  
5. Remove any additional slack from the child  
restraint. Press downward and rearward firmly  
in the center of the child restraint with your  
hand to compress the vehicle seat cushion  
and seatback while pulling up on the seat belt.  
7. Check to make sure that the child restraint is  
properly secured prior to each use. If the seat  
belt is not locked, repeat steps 1 through 6.  
6. After attaching the child restraint, test it be-  
fore you place the child in it. Push it from side  
to side while holding the child restraint near  
the seat belt path. The child restraint should  
not move more than 1 inch (25 mm), from side  
to side. Try to tug it forward and check to see  
if the belt holds the restraint in place. If the  
restraint is not secure, tighten the seat belt as  
necessary, or put the restraint in another seat  
and test it again. You may need to try a differ-  
ent child restraint. Not all child restraints fit in  
all types of vehicles.  
After the child restraint is removed and the seat  
belt fully retracted, the ALR mode (child restraint  
mode) is canceled.  
1-26 Safety–Seats, seat belts and supplemental restraint system  
Follow these steps to install a forward-facing  
child restraint using the LATCH system.  
FORWARD-FACING CHILD  
RESTRAINT INSTALLATION USING  
LATCH  
Refer to all Warnings and Cautions in “Child  
safety” and “Child restraints” in this section be-  
fore installing a child restraint.  
1. Position the child restraint on the seat. Always  
follow the child restraint manufacturer’s  
instructions.  
NISSAN does not recommend the use of the  
lower anchors if the combined weight of the child  
and the child restraint exceeds 65 lbs (29.5 kg). If  
the combined weight of the child and the child  
restraint is greater than 65 lbs, (29.5 kg) use the  
vehicle’s seat belt (not the lower anchors) to  
install the child restraint. Be sure to follow the  
child restraint manufacturer’s instructions for in-  
stallation.  
Forward-facing (webbing-mounted) —  
step 2  
2. Secure the child restraint anchor attachments  
to the LATCH lower anchors. Check to make  
sure that the LATCH attachment is properly  
attached to the lower anchors.  
If the child restraint is equipped with a top  
tether strap, route the top tether strap and  
secure the tether strap to the tether anchor  
point. See “Installing top tether strap” in this  
section. Do not install child restraints that re-  
quire the use of a top tether strap in seating  
positions that do not have a top tether anchor.  
Safety–Seats, seat belts and supplemental restraint system 1-27  
Forward-facing (rigid-mounted) — step 2  
3. The back of the child restraint should be se-  
cured against the seatback.  
Forward-facing — step 4  
4. For child restraints that are equipped with  
webbing-mounted attachments, remove any  
additional slack from the anchor attachments.  
Press downward and rearward firmly in the  
center of the child restraint with your knee to  
compress the vehicle seat cushion and seat-  
back while tightening the webbing of the an-  
chor attachments.  
Forward-facing — step 6  
6. After attaching the child restraint, test it be-  
fore you place the child in it. Push it from side  
to side while holding the child restraint near  
the LATCH attachment path. The child re-  
straint should not move more than 1 inch (25  
mm), from side to side. Try to tug it forward  
and check to see if the LATCH attachment  
holds the restraint in place. If the restraint is  
not secure, tighten the LATCH attachment as  
necessary, or put the restraint in another seat  
and test it again. You may need to try a differ-  
ent child restraint. Not all child restraints fit in  
all types of vehicles.  
If necessary, remove the head restraint/headrest  
to obtain the correct child restraint fit. If the head  
restraint/headrest is removed, store it in a secure  
place. Be sure to reinstall the head  
restraint/headrest when the child re-  
straint is removed. See “Adjust” in this sec-  
tion for headrest adjustment information.  
5. Tighten the tether strap according to the manu-  
facturer’s instructions to remove any slack.  
If the seating position does not have an adjust-  
able head restraint/headrest and it is interfering  
with the proper child restraint fit, try another seat-  
ing position or a different child restraint.  
1-28 Safety–Seats, seat belts and supplemental restraint system  
7. Check to make sure the child restraint is prop-  
erly secured prior to each use. If the child  
restraint is loose, repeat steps 1 through 6.  
Follow these steps to install a forward-facing  
child restraint using the vehicle seat belt in the  
rear seat or in the front passenger seat:  
1. If you must install a child restraint in the  
front seat, it should be placed in the  
forward-facing direction only. Move the  
seat to the rearmost position. Child re-  
straints for infants must be used in the  
rear-facing direction and therefore must  
not be used in the front seat.  
FORWARD-FACING CHILD  
RESTRAINT INSTALLATION USING  
THE SEAT BELTS  
WARNING  
The three-point seat belt with Automatic  
Locking Retractor (ALR) must be used  
when installing a child restraint. Failure  
to use the ALR mode will result in the  
child restraint not being properly se-  
cured. The restraint could tip over or be  
loose and cause injury to a child in a  
sudden stop or collision. Also, it can  
change the operation of the front passen-  
ger air bag. See “Front passenger air bag  
and status light” in this section.  
2. Position the child restraint on the seat. Always  
follow the child restraint manufacturer’s  
instructions.  
Forward-facing (front passenger seat) —  
step 1  
The back of the child restraint should be se-  
cured against the seatback.  
Refer to all Warnings and Cautions in “Child  
safety” and “Child restraints” in this section be-  
fore installing a child restraint.  
If necessary, adjust the head restraint/  
headrest (front passenger seat only) or re-  
move the head restraint/headrest to obtain the  
correct child restraint fit. If the head restraint/  
headrest is removed, store it in a secure place.  
Be sure to reinstall the head restraint/  
headrest when the child restraint is re-  
moved. See “Remove”, “Install”, or “Adjust”  
under “Head restraints/headrests” for head  
restraint/headrest adjustment, removal and in-  
stallation information.  
NISSAN does not recommend the use of the  
lower anchors if the combined weight of the child  
and the child restraint exceeds 65 lbs (29.5 kg). If  
the combined weight of the child and the child  
restraint is greater than 65 lbs, (29.5 kg) use the  
vehicle’s seat belt (in place of not the lower  
anchors) to install the child restraint. Be sure to  
follow the child restraint manufacturer’s instruc-  
tions for installation.  
Safety–Seats, seat belts and supplemental restraint system 1-29  
If the seating position does not have a remov-  
able head restraint/headrest and it is interfer-  
ing with the proper child restraint fit, try an-  
other seating position or a different child  
restraint.  
Forward-facing — step 3  
3. Route the seat belt tongue through the child  
restraint and insert it into the buckle until you  
hear and feel the latch engage. Be sure to  
follow the child restraint manufacturer’s in-  
structions for belt routing.  
Forward-facing — step 4  
4. Pull the shoulder belt until the belt is fully  
extended. At this time, the seat belt retractor  
is in the Automatic Locking Retractor (ALR)  
mode (child restraint mode). It reverts to the  
Emergency Locking Retractor (ELR) mode  
when the seat belt is fully retracted.  
If the child restraint is equipped with a top  
tether strap, route the top tether strap and  
secure the tether strap to the tether anchor  
point (rear seat installation only). See “Install-  
ing top tether strap” in this section. Do not  
install child restraints that require the use of a  
top tether strap in seating positions that do not  
have a top tether anchor.  
1-30 Safety–Seats, seat belts and supplemental restraint system  
Forward-facing — step 5  
Forward-facing — step 6  
Forward-facing — step 8  
5. Allow the seat belt to retract. Pull up on the  
shoulder belt to remove any slack in the belt.  
6. Remove any additional slack from the seat  
belt. Press downward and rearward firmly in  
the center of the child restraint with your knee  
to compress the vehicle seat cushion and  
seatback while pulling up on the seat belt.  
9. Check to make sure the child restraint is prop-  
erly secured prior to each use. If the seat belt  
is not locked, repeat steps 2 through 8.  
8. After attaching the child restraint, test it be-  
fore you place the child in it. Push it from side  
to side while holding the child restraint near  
the seat belt path. The child restraint should  
not move more than 1 inch (25 mm) from side  
to side. Try to tug it forward and check to see  
if the belt holds the restraint in place. If the  
restraint is not secure, tighten the seat belt as  
necessary, or put the restraint in another seat  
and test it again. You may need to try a differ-  
ent child restraint. Not all child restraints fit in  
all types of vehicles.  
10. If the child restraint is installed on the front  
passenger seat, push the power switch to  
the ON position. The front passenger air bag  
status light  
should illuminate. If this  
7. Tighten the tether strap according to the  
manufacturer’s instructions to remove any  
slack.  
light does not illuminate, see “Front passen-  
ger air bag and status light” in this section.  
Move the child restraint to another  
seating position. Have the system  
checked by  
dealer.  
a
NISSAN certified LEAF  
Safety–Seats, seat belts and supplemental restraint system 1-31  
•
Do not allow anything to come in con-  
tact with the strap, when the top tether  
strap is in use. Doing so may result in  
the strap being damaged in a collision.  
Your child could be seriously injured or  
killed in a collision if the child restraint  
top tether strap is damaged.  
First, secure the child restraint with the LATCH  
lower anchors (rear outboard seat positions only)  
or the seat belt, as applicable.  
1. Flip up the anchor cover from the anchor point  
which is located on the back side of the  
seatbacks.  
After the child restraint is removed and the seat  
belt is fully retracted, the ALR mode (child re-  
straint mode) is canceled.  
INSTALLING TOP TETHER STRAP  
2. If necessary, raise or remove the head  
restraint/headrest to position the top tether  
strap over the top of the seatback. If the head  
restraint/headrest is removed, store it in a  
secure place. Be sure to reinstall the head  
restraint/headrest when the child restraint is  
removed.  
WARNING  
•
Child restraint anchorages are de-  
signed to withstand only those loads  
imposed by correctly fitted child re-  
straints. Under no circumstances are  
they to be used to attach adult seat  
belts, or other items or equipment to  
the vehicle. Doing so could damage  
the child restraint anchorages. The  
child restraint will not be properly in-  
stalled using the damaged anchorage,  
and a child could be seriously injured  
or killed in a collision.  
See “Remove”, “Install”, or “Adjust” under  
“Head restraints/headrests”for head restraint/  
headrest adjustment, removal and installation  
information.  
Position the top tether strap over the top of the  
seatback.  
1-32 Safety–Seats, seat belts and supplemental restraint system  
BOOSTER SEATS  
PRECAUTIONS ON BOOSTER  
SEATS  
•
Booster seat anchorages are designed  
to withstand only those loads imposed  
by correctly fitted booster seats. Under  
no circumstances are they to be used  
to attach adult seat belts or other  
items or equipment to the vehicle. Do-  
ing so could damage the booster seat  
anchorages. The booster seat will not  
be properly installed using the dam-  
aged anchorage, and a child could be  
seriously injured or killed in a collision.  
WARNING  
Do not pass the tether strap through  
strap will be not be properly routed. Your  
child could be seriously injured or killed  
in a collision if the child restraint top  
tether strap is not properly routed (mod-  
els without rear seat).  
WARNING  
If a booster seat and seat belt are not  
used properly, the risk of a child being  
injured in a sudden stop or collision  
greatly increases:  
3. Secure the tether strap to the tether anchor  
point on the seatback.  
•
Make sure the shoulder portion of the  
belt is away from the child’s face and  
neck and the lap portion of the belt  
does not cross the stomach.  
4. Refer to the appropriate child restraint instal-  
lation procedure steps in this section before  
tightening the tether strap.  
•
•
Make sure the shoulder belt is not be-  
hind the child or under the child’s arm.  
A booster seat must only be installed  
in a seating position that has a lap/  
shoulder belt.  
If you have any questions when installing a  
top tether strap, consult your NISSAN cer-  
tified LEAF dealer for details.  
Safety–Seats, seat belts and supplemental restraint system 1-33  
Booster seats of various sizes are offered by  
several manufacturers. When selecting any  
booster seat, keep the following points in mind:  
• Make sure the child’s head will be properly  
supported by the booster seat or vehicle seat.  
The seatback must be at or above the center of  
the child’s ears. For example, if a low back  
1
• If the booster seat is compatible with your ve-  
hicle, place your child in the booster seat and  
check the various adjustments to be sure the  
booster seat is compatible with your child. Al-  
ways follow all recommended procedures.  
• Choose only a booster seat with a label certify-  
ing that it complies with Federal Motor Vehicle  
Safety Standard 213 or Canadian Motor Ve-  
hicle Safety Standard 213.  
booster seat  
is chosen, the vehicle seatback  
᭺
must be at or above the center of the child’s  
ears. If the seatback is lower than the center of  
All U.S. states and Canadian provinces or  
territories require that infants and small  
children be restrained in an approved child  
restraint at all times while the vehicle is  
being operated.  
2
the child’s ears, a high back booster seat  
᭺
• Check the booster seat in your vehicle to be  
sure it is compatible with the vehicle’s seat and  
seat belt system.  
should be used.  
The instructions in this section apply to booster  
seat installation in the rear seats or the front  
passenger seat.  
1-34 Safety–Seats, seat belts and supplemental restraint system  
BOOSTER SEAT INSTALLATION  
CAUTION  
Do not use the lap/shoulder belt Auto-  
matic Locking Retractor (ALR) mode  
when using a booster seat with the seat  
belts.  
Refer to all Warnings and Cautions in “Child  
safety”, “Child restraints” and “Booster seats” in  
this section before installing a child restraint.  
Follow these steps to install a booster seat on the  
rear seat or on the front passenger seat:  
Front passenger seat  
1. If you must install a booster seat in the  
front seat, move the seat to the rearmost  
position.  
Front passenger seat  
If necessary, adjust or remove the head  
restraint/headrest to obtain the correct  
booster seat fit. If the head restraint/headrest  
is removed, store it in a secure place. Be sure  
to reinstall the head restraint/headrest  
when the booster seat is removed. See  
“Remove”, “Install” or “Adjust” under “Head  
restraints/headrests” for head restraint/  
headrest adjustment, removal and installation  
information.  
2. Position the booster seat on the seat. Only  
place it in the forward-facing direction. Al-  
ways follow the booster seat manufacturer’s  
instructions.  
3. The booster seat should be positioned on the  
vehicle seat so that it is stable.  
Safety–Seats, seat belts and supplemental restraint system 1-35  
SUPPLEMENTAL RESTRAINT  
SYSTEM  
PRECAUTIONS ON SUPPLEMENTAL  
RESTRAINT SYSTEM  
This Supplemental Restraint System (SRS) sec-  
tion contains important information concerning  
the following systems.  
If the seating position does not have an adjust-  
able head restraint/headrest and it is interfer-  
ing with the proper booster seat fit, try another  
seating position or a different booster seat.  
4. Position the lap portion of the seat belt low  
and snug on the child’s hips. Be sure to follow  
the booster seat manufacturer’s instructions  
for adjusting the seat belt routing.  
• Driver and passenger supplemental front-  
impact air bag (NISSAN Advanced Air Bag  
System)  
5. Pull the shoulder belt portion of the seat belt  
toward the retractor to take up extra slack. Be  
sure the shoulder belt is positioned across the  
top, middle portion of the child’s shoulder. Be  
sure to follow the booster seat manufacturer’s  
instructions for adjusting the seat belt routing.  
• Front seat-mounted side-impact supplemental  
air bag  
• Roof-mounted curtain side-impact supplemen-  
tal air bag  
7. If the booster seat is installed in the front  
passenger seat, push the power switch to the  
ON position. The front passenger air bag sta-  
• Seat belt with pretensioner  
6. Follow the warnings, cautions and instruc-  
tions for properly fastening a seat belt shown  
in “Three-point type seat belt with retractor”.  
Supplemental front-impact air bag system:  
The NISSAN Advanced Air Bag System can help  
cushion the impact force to the head and chest of  
the driver and front passenger in certain frontal  
collisions.  
tus light  
may or may not illuminate  
depending on the size of the child and the  
type of booster seat used. See “Front passen-  
ger air bag and status light” in this section.  
Front seat-mounted side-impact supple-  
mental air bag system: This system can help  
cushion the impact force to the chest and pelvic  
area of the driver and front passenger in certain  
side impact collisions. The side air bag is de-  
signed to inflate on the side where the vehicle is  
impacted.  
1-36 Safety–Seats, seat belts and supplemental restraint system  
Roof-mounted curtain side-impact supple-  
mental air bag system: This system can help  
cushion the impact force to the head of occu-  
pants in front and rear outboard seating positions  
in certain side impact collisions. In a side impact,  
the curtain air bags are designed to inflate on the  
side where the vehicle is impacted.  
These supplemental restraint systems are de-  
signed to supplement the crash protection pro-  
vided by the driver and passenger seat belts and  
are not a substitute for them. Seat belts should  
always be correctly worn, and the occupant  
should be seated a suitable distance away from  
the steering wheel, instrument panel and door  
finishers. See “Seat belts” in this section for  
instructions and precautions on seat belt usage.  
The supplemental air bags operate only  
when the power switch is in the ON posi-  
tion.  
After the power switch is placed in the ON  
position, the supplemental air bag warning  
light illuminates. The supplemental air bag  
warning light will turn off after about 7  
seconds if the systems are operational.  
Safety–Seats, seat belts and supplemental restraint system 1-37  
•
•
The driver and front passenger seat  
belt buckles are equipped with sen-  
sors that detect if the seat belts are  
fastened. The Advanced Air Bag Sys-  
tem monitors the severity of a collision  
and seat belt usage then inflates the  
air bags as needed. Failure to properly  
wear seat belts can increase the risk or  
severity of injury in an accident.  
The front passenger seat is equipped  
with occupant classification sensors  
(weight sensors) that turn the front  
passenger air bag OFF under some  
conditions. This sensor is only used in  
this seat. Failure to be properly seated  
and wearing the seat belt can increase  
the risk or severity of injury in an acci-  
dent. See “Front passenger air bag  
and status light” in this section.  
WARNING  
•
The front air bags ordinarily will not  
inflate in the event of a side impact,  
rear impact, rollover or lower severity  
frontal collision. Always wear your  
seat belts to help reduce the risk or  
severity of injury in various kinds of  
accidents.  
•
•
The front passenger air bag will not  
inflate if the passenger air bag status  
light is lit or if the front passenger seat  
is unoccupied. See “Front passenger  
air bag and status light”in this section.  
The seat belts and the front air bags are  
most effective when you are sitting well  
back and upright in the seat with both  
feet on the floor. The front air bags inflate  
with great force. Even with the NISSAN  
Advanced Air Bag System, if you are un-  
restrained, leaning forward, sitting side-  
ways or out of position in any way, you  
are at greater risk of injury or death in a  
crash. You may also receive serious or  
fatal injuries from the front air bag if you  
are up against it when it inflates. Always  
sit back against the seatback and as far  
away as practical from the steering wheel  
or instrument panel. Always use the seat  
belts.  
•
Keep hands on the outside of the  
steering wheel. Placing them inside  
the steering wheel rim could increase  
the risk that they are injured if the front  
air bag inflates.  
1-38 Safety–Seats, seat belts and supplemental restraint system  
WARNING  
•
•
•
Never let children ride unrestrained or  
extend their hands or face out of the  
window. Do not attempt to hold them  
in your lap or arms. Some examples of  
dangerous riding positions are shown  
in the illustrations.  
Children may be severely injured or  
killed when the front air bags, side air  
bags or curtain air bags inflate if they  
are not properly restrained. Pre-teens  
and children should be properly re-  
strained in the rear seat, if possible.  
Even with the NISSAN Advanced Air  
Bag System, never install a rear-facing  
child restraint on the front seat. An  
inflating front air bag could seriously  
injure or kill your child. See “Child re-  
straints” in this section for details.  
Safety–Seats, seat belts and supplemental restraint system 1-39  
Do not lean against doors or windows.  
WARNING  
Front seat-mounted side-impact supple-  
mental air bags and roof-mounted cur-  
tain side-impact supplemental air bags:  
•
The side air bags and curtain air bags  
ordinarily will not inflate in the event of  
a frontal impact, rear impact, rollover  
or lower severity side collision. Always  
wear your seat belts to help reduce the  
risk or severity of injury in various  
kinds of accidents.  
1-40 Safety–Seats, seat belts and supplemental restraint system  
•
The seat belts, the side air bags and  
curtain air bags are most effective  
when you are sitting well back and  
upright in the seat. The side air bag  
and curtain air bag inflate with great  
force. Do not allow anyone to place  
their hand, leg or face near the side air  
bag on the side of the seatback of the  
front seat or near the side roof rails. Do  
not allow anyone sitting in the front  
seats or rear outboard seats to extend  
their hand out of the window or lean  
against the door. Some examples of  
dangerous riding positions are shown  
in the previous illustrations.  
•
•
When sitting in the rear seat, do not  
hold onto the seatback of the front  
seat. If the side air bag inflates, you  
may be seriously injured. Be especially  
careful with children, who should al-  
ways be properly restrained. Some ex-  
amples of dangerous riding positions  
are shown in the illustrations.  
Do not use seat covers on the front  
seatbacks. They may interfere with  
side air bag inflation.  
Safety–Seats, seat belts and supplemental restraint system 1-41  
9. Lap outer pretensioner (driver side only)  
10. Seat belt with pretensioner  
11. Air bag Control Unit (ACU)  
NISSAN ADVANCED AIR BAG  
SYSTEM (FRONT SEATS)  
WARNING  
To ensure proper operation of the pas-  
senger’s advanced air bag system, please  
observe the following items.  
•
Do not allow a passenger in the rear  
seat to push or pull on the seatback  
pocket.  
•
Do not place heavy loads heavier than  
9lb (4 kg) on the seatback, head  
restraint/headrest or in the seatback  
pocket.  
•
•
Do not store luggage behind the seat  
that can press into the seatback.  
Confirm the operating condition with  
the front passenger air bag status  
light.  
1. Crash zone sensor  
5. Occupant classification system control unit  
6. Roof-mounted curtain side-impact supple-  
mental air bag inflators  
7. Roof-mounted curtain side-impact supple-  
mental air bag modules  
2. Supplemental front-impact air bag modules  
3. Front seat-mounted side-impact supplemen-  
tal air bag modules  
4. Occupant classification sensors (weight  
sensors)  
8. Satellite sensors  
1-42 Safety–Seats, seat belts and supplemental restraint system  
always an indication of proper front air bag op-  
eration.  
LEAF dealer. If you are considering modification  
of your vehicle due to a disability, you may also  
contact NISSAN. Contact information is con-  
tained in the front of this Owner’s Manual.  
•
•
If you notice that the front passenger  
air bag status light is not operating as  
described in this section, please take  
your vehicle to your NISSAN certified  
LEAF dealer to check the occupant  
classification system.  
Until you have confirmed with your  
dealer that your passenger seat occu-  
pant classification system is working  
properly, position the occupants in the  
rear seating positions.  
The NISSAN Advanced Air Bag System has dual  
stage air bag inflators. The system monitors infor-  
mation from the Air bag Control Unit (ACU), seat  
belt buckle sensors and the occupant classifica-  
tion sensors (weight sensors). Inflator operation  
is based on the severity of a collision and seat  
belt usage for the driver. For the front passenger,  
the occupant classification sensors are also  
monitored. Based on information from the sen-  
sors, only one front air bag may inflate in a crash,  
depending on the crash severity and whether the  
front occupants are belted or unbelted. Addition-  
ally, the front passenger air bag may be automati-  
cally turned OFF under some conditions, de-  
pending on the information provided by the  
occupant classification sensors. If the front pas-  
senger air bag is OFF, the passenger air bag  
status light will be illuminated (if the seat is unoc-  
cupied, the light will not be illuminated, but the air  
bag will be off). See “Front passenger air bag and  
status light”in this section for further details. One  
front air bag inflating does not indicate improper  
performance of the system.  
When a front air bag inflates, a fairly loud noise  
may be heard, followed by release of smoke. This  
smoke is not harmful and does not indicate a fire.  
Care should be taken not to inhale it, as it may  
cause irritation and choking. Those with a history  
of a breathing condition should get fresh air  
promptly.  
This vehicle is equipped with the NISSAN Ad-  
vanced Air Bag System for the driver and front  
passenger seats. This system is designed to  
meet certification requirements under U.S. regu-  
lations. It is also permitted in Canada. All of the  
information, cautions and warnings in this  
manual apply and must be followed.  
Front air bags, along with the use of seat belts,  
help to cushion the impact force on the head and  
chest of the front occupants. They can help save  
lives and reduce serious injuries. However, an  
inflating front air bag may cause facial abrasions  
or other injuries. Front air bags do not provide  
restraint to the lower body.  
The driver supplemental front-impact air bag is  
located in the center of the steering wheel. The  
passenger supplemental front-impact air bag is  
mounted in the instrument panel above the glove  
box. The front air bags are designed to inflate in  
higher severity frontal collisions, although they  
may inflate if the forces in another type of collision  
are similar to those of a higher severity frontal  
impact. They may not inflate in certain frontal  
collisions. Vehicle damage (or lack of it) is not  
Even with NISSAN Advanced Air Bags, seat  
belts should be correctly worn and the driver and  
passenger seated upright as far as practical  
away from the steering wheel or instrument  
panel. The front air bags inflate quickly in order to  
help protect the front occupants. Because of this,  
the force of the front air bag inflating can increase  
the risk of injury if the occupant is too close to, or  
is against, the air bag module during inflation.  
If you have any questions about your air bag  
system, contact NISSAN or a NISSAN certified  
Safety–Seats, seat belts and supplemental restraint system 1-43  
The front air bags deflate quickly after a collision.  
• Passenger’s seat occupied by a small adult,  
child or child restraint as outlined in this section:  
The front air bags operate only when the  
power switch is in the ON position.  
The  
light illuminates to indicate that the  
front passenger air bag is OFF and will not  
inflate in a crash.  
After the power switch is placed in the ON  
position, the supplemental air bag warning  
light illuminates. The supplemental air bag  
warning light will turn off after about 7  
seconds if the system is operational.  
• Occupied passenger seat and the passenger  
meets the conditions outlined in this section:  
The  
light is OFF to indicate that the front  
passenger air bag is operational.  
Front passenger air bag and status  
light  
Front passenger air bag:  
The front passenger air bag is designed to auto-  
matically turn OFF when the vehicle is operated  
under some conditions as described below as  
permitted by U.S. regulations. If the front passen-  
ger air bag is OFF, it will not inflate in a crash. The  
driver air bag and other air bags in your vehicle  
are not part of this system.  
Front passenger air bag status light  
Status light:  
The front passenger air bag status light  
located on the instrument panel. After the power  
switch is pushed to the ON position, the front  
passenger air bag status light on the instrument  
panel illuminates for about 7 seconds and then  
turns off or illuminates depending on the front  
passenger seat status. The light operates as fol-  
lows:  
WARNING  
The front passenger air bag is designed  
to automatically turn OFF under some  
conditions. Read this section carefully to  
learn how it operates. Proper use of the  
seat, seat belt and child restraints is nec-  
essary for most effective protection. Fail-  
ure to follow all instructions in this  
manual concerning the use of seats, seat  
belts and child restraints can increase the  
risk or severity of injury in an accident.  
is  
The purpose of the regulation is to help reduce  
the risk of injury or death from an inflating air bag  
to certain front passenger seat occupants, such  
as children, by requiring the air bag to be auto-  
matically turned OFF.  
• Unoccupied passenger seat: The  
OFF and the front passenger air bag is OFF and  
will not inflate in a crash.  
light is  
One sensor used is the occupant classification  
sensor (weight sensor). Its is designed to detect  
an occupant and objects on the seat by weight.  
For example, if a child is in the front passenger  
1-44 Safety–Seats, seat belts and supplemental restraint system  
seat, the Advanced Air Bag System is designed  
to turn the passenger air bag OFF in accordance  
with the regulations. Also, if a child restraint of the  
type specified in the regulations is on the seat, its  
weight and the child’s weight can be detected  
and cause the air bag to turn OFF.  
properly secure child restraints and to use the  
Automatic Locking Retractor (ALR) mode (child  
restraint mode) may allow the restraint to tip or  
move in an accident or sudden stop. This can  
also result in the passenger air bag inflating in a  
crash instead of being OFF. See “Child re-  
straints” in this section for proper use and instal-  
lation.  
person is a small adult, or is not sitting on the seat  
properly.  
If a child restraint must be used in the front seat,  
the passenger air bag status light may or may not  
be illuminated, depending on the size of the child  
and the type of child restraint being used. If the air  
bag status light is not illuminated (indicating that  
the air bag might inflate in a crash), it could be  
that the child restraint or seat belt is not being  
used properly. Make sure that the child restraint is  
installed properly, the seat belt is used properly  
and the occupant is positioned properly. If the air  
bag status light is not illuminated, reposition the  
occupant or child restraint in a rear seat.  
Front passenger seat adult occupants who are  
properly seated and using the seat belt as out-  
lined in this manual should not cause the passen-  
ger air bag to be automatically turned OFF. For  
small adults it may be turned OFF, however, if the  
occupant does not sit in the seat properly (for  
example, by not sitting upright, by sitting on an  
edge of the seat, or by otherwise being out of  
position), this could cause the sensors to turn the  
air bag OFF. Always be sure to be seated and  
wearing the seat belt properly for the most effec-  
tive protection by the seat belt and supplemental  
air bag.  
If the front passenger seat is not occupied, the  
passenger air bag is designed not to inflate in a  
crash. However, heavy objects placed on the  
seat could result in air bag inflation, because of  
the object being detected by the occupant clas-  
sification sensors. Other conditions could also  
result in air bag inflation, such as if a child is  
standing on the seat, or if two children are on the  
seat, contrary to the instructions in this manual.  
Always be sure that you and all vehicle occupants  
are seated and restrained properly.  
If the passenger air bag status light will not illu-  
minate even though you believe that the child  
restraint, the seat belts and the occupant are  
properly positioned, the system may be sensing  
an unoccupied seat (in which case the air bag is  
OFF). Your NISSAN certified LEAF dealer can  
check that the system is OFF by using a special  
tool. However, until you have confirmed with your  
dealer that your air bag is working properly, repo-  
sition the occupant or child restraint in a rear seat.  
NISSAN recommends that pre-teens and chil-  
dren be properly restrained in a rear seat.  
NISSAN also recommends that appropriate child  
restraints and booster seats be properly installed  
in a rear seat. If this is not possible, the occupant  
classification sensors are designed to operate as  
described above to turn the front passenger air  
bag OFF for specified child restraints. Failing to  
Using the passenger air bag status light, you can  
monitor when the front passenger air bag is au-  
tomatically turned OFF with the seat occupied.  
The light will not illuminate when the front pas-  
senger seat is unoccupied.  
If an adult occupant is in the seat but the passen-  
ger air bag status light is illuminated (indicating  
that the air bag is OFF), it could be that the  
The air bag system and passenger air bag status  
light will take a few seconds to register a change  
in the passenger seat status. However, if the seat  
Safety–Seats, seat belts and supplemental restraint system 1-45  
becomes unoccupied, the air bag status light will  
remain off.  
•
•
Do not place objects with sharp edges  
on the seat. Also, do not place heavy  
objects on the seat that will leave per-  
manent impressions in the seat. Such  
objects can damage the seat or occu-  
pant classification sensors (weight  
sensors). This can affect the operation  
of the air bag system and result in  
serious personal injury.  
Do not use water or acidic cleaners  
(hot steam cleaners) on the seat. This  
can damage the seat or occupant clas-  
sification sensors. This can also affect  
the operation of the air bag system  
and result in serious personal injury.  
Immediately after inflation, several  
front air bag system components will  
be hot. Do not touch them; you may  
severely burn yourself.  
No unauthorized changes should be  
made to any components or wiring of  
the supplemental air bag system. This  
is to prevent accidental inflation of the  
supplemental air bag or damage to the  
supplemental air bag system.  
Do not make unauthorized changes to  
your vehicle’s electrical system, sus-  
pension system or front end structure.  
This could affect proper operation of  
the front air bag system.  
•
Tampering with the front air bag sys-  
tem may result in serious personal in-  
jury. Tampering includes changes to  
the steering wheel and the instrument  
panel assembly by placing material  
over the steering wheel pad and above  
the instrument panel or by installing  
additional trim material around the air  
bag system.  
Removing or modifying the front pas-  
senger seat may affect the function of  
the air bag system and result in serious  
personal injury.  
Modifying or tampering with the front  
passenger seat may result in serious  
personal injury. For example, do not  
change the front seats by placing ma-  
terial on the seat cushion or by install-  
ing additional trim material, such as  
seat covers, on the seat that is not  
specifically designed to assure proper  
air bag operation. Additionally, do not  
stow any objects under the front pas-  
senger seat or the seat cushion and  
seatback. Such objects may interfere  
with the proper operation of the occu-  
pant classification sensors.  
If a malfunction occurs in the front passenger air  
bag system, the supplemental air bag warning  
light  
, located in the meter and gauges area,  
will blink. Have the system checked by a NISSAN  
certified LEAF dealer.  
Other supplemental front-impact air  
bag precautions  
•
•
WARNING  
•
Do not place any objects on the steer-  
ing wheel pad or on the instrument  
panel. Also, do not place any objects  
between any occupant and the steer-  
ing wheel or instrument panel. Such  
objects may become dangerous pro-  
jectiles and cause injury if the front air  
bags inflate.  
•
•
•
1-46 Safety–Seats, seat belts and supplemental restraint system  
collision are similar to those of a higher severity  
side impact. They are designed to inflate on the  
side where the vehicle is impacted. They may not  
inflate in certain side collisions on the side where  
the vehicle is impacted.  
•
•
No unauthorized changes should be  
made to any components or wiring of  
the seat belt system. This may affect  
the front air bag system. Tampering  
with the seat belt system may result in  
serious personal injury.  
Work on and around the front air bag  
system should be done by a NISSAN  
certified LEAF dealer. Installation of  
electrical equipment should also be  
Vehicle damage (or lack of it) is not always an  
indication of proper side air bag and curtain air  
bag operation.  
When the side air bags and curtain air bags  
inflate, a fairly loud noise may be heard, followed  
by release of smoke. This smoke is not harmful  
and does not indicate a fire. Care should be taken  
not to inhale it, as it may cause irritation and  
choking. Those with a history of a breathing con-  
dition should get fresh air promptly.  
done by  
a
NISSAN certified LEAF  
dealer. The Supplemental Restraint  
System (SRS) wiring harnesses*  
should not be modified or discon-  
nected. Unauthorized electrical test  
equipment and probing devices should  
not be used on the air bag system.  
A cracked windshield should be re-  
placed immediately by a qualified re-  
FRONT SEAT-MOUNTED  
SIDE-IMPACT SUPPLEMENTAL AIR  
BAG AND ROOF-MOUNTED  
CURTAIN SIDE-IMPACT  
•
Side air bags, along with the use of seat belts,  
help to cushion the impact force on the chest and  
pelvic area of the front occupants. Curtain air  
bags help to cushion the impact force to the head  
of occupants in the front and rear outboard seat-  
ing positions. They can help save lives and re-  
duce serious injuries. However, side air bags and  
curtain air bags may cause abrasions or other  
injuries. Side air bags and curtain air bags do not  
provide restraint to the lower body.  
pair facility.  
A
cracked windshield  
could affect the function of the supple-  
mental air bag system.  
SUPPLEMENTAL AIR BAG SYSTEMS  
The side air bags are located in the outside of the  
seatback of the front seats. The curtain air bags  
are located in the side roof rails. All of the  
information, cautions, and warnings in this  
manual apply and must be followed. The  
side air bags and curtain air bags are designed to  
inflate in higher severity side collisions, although  
they may inflate if the forces in another type of  
*The SRS wiring harness connectors are  
yellow and orange for easy identification.  
When selling your vehicle, we request that you  
inform the buyer about the front air bag system  
and guide the buyer to the appropriate sections  
in this Owner’s Manual.  
The seat belts should be correctly worn and the  
driver and passenger seated upright as far as  
Safety–Seats, seat belts and supplemental restraint system 1-47  
practical away from the side air bags. Rear seat  
passengers should be seated as far away as  
practical from the door finishers and side roof  
rails. The side air bags and curtain air bags inflate  
quickly in order to help protect the occupants in  
the outboard seating positions. Because of this,  
the force of the side air bags and curtain air bags  
inflating can increase the risk of injury if the oc-  
cupant is too close to, or is against, these air bag  
modules during inflation. The side air bags and  
curtain air bags will deflate quickly after the colli-  
sion is over.  
•
•
Tampering with the side air bag system  
may result in serious personal injury.  
For example, do not change the front  
seats by placing material near the  
seatbacks or by installing additional  
trim material, such as seat covers,  
around the side air bag.  
WARNING  
•
Do not place any objects near the seat-  
back of the front seats. Also, do not  
place any objects (an umbrella, bag,  
etc.) between the front door finisher  
and the front seat. Such objects may  
become dangerous projectiles and  
cause injury if a side air bag inflates.  
Right after inflation, several side air  
bag and curtain air bag system compo-  
nents will be hot. Do not touch them;  
you may severely burn yourself.  
No unauthorized changes should be  
made to any components or wiring of  
the side air bag and curtain air bag  
systems. This is to prevent damage to  
or accidental inflation of the side air  
bag and curtain air bag systems.  
Work around and on the side air bag  
and curtain air bag systems should be  
done by  
a
NISSAN certified LEAF  
•
•
dealer. Installation of electrical equip-  
ment should also be done by a NISSAN  
certified LEAF dealer. The Supplemen-  
tal Restraint System (SRS) wiring har-  
nesses* should not be modified or dis-  
connected. Unauthorized electrical  
test equipment and probing devices  
should not be used on the side air bag  
and curtain supplemental air bag sys-  
tems.  
The side air bags and curtain air bags op-  
erate only when the power switch is in the  
ON position.  
After turning the power switch to the ON  
position, the supplemental air bag warning  
light illuminates. The supplemental air bag  
warning light will turn off after about 7  
seconds if the systems are operational.  
•
Do not make unauthorized changes to  
your vehicle’s electrical system, sus-  
pension system or side panel. This  
could affect proper operation of the  
side air bag and curtain air bag sys-  
tems.  
*The SRS wiring harness connectors are  
yellow and orange for easy identification.  
When selling your vehicle, we request that you  
inform the buyer about the side air bag and  
curtain air bag systems and guide the buyer to  
the appropriate sections in this Owner’s Manual.  
1-48 Safety–Seats, seat belts and supplemental restraint system  
When a pretensioner activates, smoke is re-  
leased and a loud noise may be heard. The smoke  
is not harmful and does not indicate a fire. Care  
should be taken not to inhale it, as it may cause  
irritation and choking. Those with a history of a  
breathing condition should get fresh air promptly.  
SEAT BELTS WITH  
•
•
Work around and on the pretensioner  
system should be done by a NISSAN  
certified LEAF dealer. Installation of  
electrical equipment should also be  
PRETENSIONERS (FRONT SEATS)  
WARNING  
done by  
a
NISSAN certified LEAF  
dealer. Unauthorized electrical test  
equipment and probing devices should  
not be used on the pretensioner sys-  
tem.  
If you need to dispose of a preten-  
sioner or scrap the vehicle, contact a  
NISSAN certified LEAF dealer. Correct  
pretensioner disposal procedures are  
set forth in the appropriate NISSAN  
Service Manual. Incorrect disposal  
procedures could cause personal in-  
jury.  
•
•
The pretensioners cannot be reused  
after activation. They must be replaced  
together with the retractor and buckle  
as a unit.  
If the vehicle becomes involved in a  
collision but a pretensioner is not acti-  
vated, be sure to have the pretensioner  
system checked and, if necessary, re-  
placed by a NISSAN certified LEAF  
dealer.  
After pretensioner activation, load limiters allow  
the seat belt to release webbing (if necessary) to  
reduce forces against the chest.  
The supplemental air bag warning light  
is  
used to indicate malfunctions in the pretensioner  
system. (See “Supplemental air bag warning  
light” in this section for more details.) If the  
supplemental air bag warning light indicates  
there is a malfunction, have the system checked  
by a NISSAN certified LEAF dealer.  
•
No unauthorized changes should be  
made to any components or wiring of  
the pretensioner system. This is to pre-  
vent damage to or accidental activa-  
tion of the pretensioners. Tampering  
with the pretensioner system may re-  
sult in serious personal injury.  
The pretensioner system may activate with the  
supplemental air bag system in certain types of  
collisions. Working with the seat belt retractor, it  
helps tighten the seat belt when the vehicle be-  
comes involved in certain types of collisions,  
helping to restrain front seat occupants.  
When selling your vehicle, we request that you  
inform the buyer about the pretensioner system  
and guide the buyer to the appropriate sections  
in this Owner’s Manual.  
The pretensioner is encased with the seat belt  
retractor for both front seating positions. The  
driver’s seat belt also has a pretensioner at the  
outer floor anchor. These seat belts are used the  
same way as conventional seat belts.  
Safety–Seats, seat belts and supplemental restraint system 1-49  
When the power switch is in the ON position, the  
supplemental air bag warning light illuminates for  
about 7 seconds and then turns off. This means  
the system is operational.  
If any of the following conditions occur, the front  
air bag, side air bag, curtain air bag and preten-  
sioner systems need servicing:  
• The supplemental air bag warning light remains  
on after approximately 7 seconds.  
• The supplemental air bag warning light flashes  
intermittently.  
• The supplemental air bag warning light does not  
come on at all.  
SUPPLEMENTAL AIR BAG  
WARNING LABELS  
Warning labels about the supplemental front-  
impact air bag system are placed in the vehicle as  
shown in the illustration.  
SUPPLEMENTAL AIR BAG  
WARNING LIGHT  
The supplemental air bag warning light, display-  
Under these conditions, the front air bag, side air  
bag, curtain air bag and pretensioner systems  
may not operate properly. They must be checked  
and repaired. Take your vehicle to the nearest  
NISSAN certified LEAF dealer.  
ing  
in the instrument panel, monitors the  
circuits of the Air bag Control Unit (ACU), satel-  
lite sensors, crash zone sensor, occupant classi-  
fication sensors, the supplemental front-impact  
air bag, front seat-mounted side-impact supple-  
mental air bag, roof-mounted curtain side-impact  
supplemental air bag and seat belt pretensioner  
systems. The monitored circuits include air bag  
systems, pretensioners and all related wiring.  
1
᭺
SRS air bag  
The warning labels are located on the surface of  
the sun visors.  
1-50 Safety–Seats, seat belts and supplemental restraint system  
WARNING  
WARNING  
If the supplemental air bag warning light  
is on, it could mean that the front air bag,  
side air bag, curtain air bag and/or pre-  
tensioner systems will not operate in an  
accident. To help avoid injury to yourself  
or others, have your vehicle checked by a  
NISSAN certified LEAF dealer as soon as  
possible.  
•
Once a front air bag, side air bag or  
curtain air bag has inflated, the air bag  
module will not function again and  
must be replaced. Additionally, the ac-  
tivated pretensioners must also be re-  
placed. The air bag module and preten-  
sioner should be replaced by  
a
NISSAN certified LEAF dealer. The air  
bag modules and pretensioner system  
cannot be repaired.  
The front air bag, side air bag and  
curtain air bag systems, and preten-  
sioner system should be inspected by  
a NISSAN certified LEAF dealer if there  
is any damage to the front end or side  
portion of the vehicle.  
If you need to dispose of a supplemen-  
tal air bag or pretensioner or scrap the  
vehicle, contact a NISSAN certified  
LEAF dealer. Correct supplemental air  
bag and pretensioner system disposal  
procedures are set forth in the appro-  
priate NISSAN Service Manual. Incor-  
rect disposal procedures could cause  
personal injury.  
REPAIR AND REPLACEMENT  
PROCEDURE  
•
•
The front air bags, side air bags, curtain air bags  
and pretensioners are designed to activate on a  
one-time-only basis. As a reminder, unless it is  
damaged, the supplemental air bag warning light  
will remain illuminated after inflation has oc-  
curred. Repair and replacement of these systems  
should be done only by a NISSAN certified LEAF  
dealer.  
When maintenance work is required on the ve-  
hicle, the front air bags, side air bags, curtain air  
bags and pretensioners and related parts should  
be pointed out to the person performing the  
maintenance. The power switch should always  
be in the LOCK position when working under the  
hood or inside the vehicle.  
Safety–Seats, seat belts and supplemental restraint system 1-51  
NOTES  
1-52 Safety–Seats, seat belts and supplemental restraint system  

Related Topics

Popular Owner Manuals