2004-2009 Nissan Micra 4 Door In case of emergency User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

In case of emergency for Your Nissan Micra 4 Door Third Generation (2004-2009)

6 In case of emergency
Hazard indicator flasher switch
....
............................................................ 6-2
Flat tire
....
....................................................................................................... 6-2
Stopping vehicle
....
............................................................................... 6-2
Preparing tools
....
.................................................................................. 6-2
Changing flat tire (for model with spare tire)
....
............................ 6-3
Repairing flat tire (for model with emergency tire puncture
repair kit)
....
............................................................................................. 6-6
Jump starting
....
............................................................................................ 6-9
Push starting
....
......................................................................................... 6-10
If your vehicle overheats
....
.................................................................... 6-11
Towing your vehicle
....
............................................................................. 6-11
Towing precautions
....
..................................................................... 6-11
Towing recommended by NISSAN
....
......................................... 6-12
6-2 In case of emergency
GUID-BE653282-21EF-4712-85BE-F8F83E49F9ED
SIC2475
The hazard indicator flasher switch operates with the
ignition switch in any position except when the battery
is discharged.
The hazard indicator flasher is used to warn other
drivers when you have to stop or park under
emergency conditions.
When the hazard indicator flasher switch is pushed, all
turn signal lights will flash. To turn off the hazard
indicator flasher, push the hazard indicator flasher
switch again.
GUID-24B46F6D-6DFB-41EB-94FF-89CA5420853A
If you have a flat tire, follow the instructions as follows.
STOPPING VEHICLE
GUID-F82E648B-352A-49 5D-AAE8-5110EB688C7F
WARNING:
. Be sure to apply the parking brake firmly.
. Be sure to move the shift lever to the “R”
(Reverse) position (Manual Transmiss ion
(MT) model).
. Be sure to move the shift lever to the “P”
(Park) position. (Automatic Transmission
(AT)/Continuously Variable Transmission
(CVT) model)
. Never change tires when the vehicle is on a
slope, ice or slippery area. This is hazardous.
. Never change tires when the oncoming
traffic is close to your vehicle. Call for
professional road assistance.
1. Safely move the vehicle off the road away from
traffic.
2. Turn on the hazard indicator flasher lights.
3. Park on a level surface.
4. Apply the parking brake.
5. Automatic Transmission (AT)/Continuously Vari-
able Transmission (CVT) model: Move the shift
lever to the “P” (Park) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position.
6. Turn off the engine.
7. Open the hood and set up the warning triangle (if
equipped):
.
To warn other traffic.
.
To signal professional road assistance person-
nel that you need assistance.
8. Have all passengers get out from the vehicle and
stand in a safe place, away from other traffic and
clear of the vehicle.
PREPARING TOOLS
GUID-B5B1218E-5C18-4B1A-9B1D-E5D272149790
SCE0902
Raise the back door floor cover.
Your vehicle is equipped with either a spare tire or an
emergency tire puncture repair kit. Carefully read the
instructions provided in the appropriate section.
HAZARD INDICATOR FLASHER
SWITCH
FLAT TIRE
. For model with spare tire: See “Changing flat tire
(for model with spare tire)” (P.6-3).
. For model with emergency tire puncture repair kit:
See “Repairing flat tire (for model with emergency
tire puncture repair kit)” (P.6-6).
CHANGING FLAT TIRE (for model with spare
tire)
GUID-7AF80AB9-8680-49C3-86F9-7B6C9C5AA65A
SCE0913
Remove the jack, necessary tools and the spare tire
from the storage area.
If spacers are equipped, remove them before removing
the spare tire.
Blocking wheels
GUID-829AECDE-D055-4A7F-8E7C-52F9E88267B4
MCE0001A
WARNING:
Be sure to bloc k the appropriate wheel to
prevent the vehicle from moving, which may
cause personal injury.
Place suitable blocks
*
1
at both the front and back of
the wheel diagonally opposite the flat tire
to
prevent the vehicle from moving when it is jacked up.
Removing wheel cover
GUID-F360DEF0-D3CC-4086-9915-00F60CC4007D
SCE0630
Type A
SCE0637
Type B
Type A:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
WARNING:
Never use your hands to remove the wheel
cover. This may cause personal injury.
To remove the wheel cover, use the jack rod
*
1
as
illustrated.
Apply cloth
*
2
between the wheel and jack rod to
prevent damaging the wheel and wheel cover.
Type B:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Remove the center wheel cap as illustrated.
Removing tire
GUID-AC9FA5DF-0E35-4BD5-8A14-4A93AE2C81A2
SCE0903
Jack-up points
In case of emergency 6-3
6-4 In case of emergency
SCE0914
Floor jack-up point (rear)
For the rear, never jack up the vehicle at a location
other than the floor jack-up point that is specified.
WARNING:
. Be sure to read and follow the instructions in
this section.
. DO NOT GET UNDER A VEHICLE THAT IS
SUPPORTED BY A JACK.
. Never use a jack which was not provided
with your vehicle.
. The jack, which is provided with your vehicle,
is designed only to lift your vehicle during a
tire change. Do not use the jack provided
with your vehicle on other vehicles.
. Never jack up the vehicle at a location other
than the jack-up point that is specified.
. Never lift the vehicle more than necessary.
. Never use blocks on or under the jack.
. Never start or run the engine while the
vehicle is on the jack. The vehicle may move
suddenly, and this may cause an accident.
. Never allow passengers to remain in the
vehicle while the tire is off the ground.
. Be sure to read the caution label attached to
the jack body before using.
Jacking up vehicle
GUID-AD0EA628-66DE-4106-9301-941D266A20DE
SCE0504
1. Place the jack directly under the jack-up point as
illustrated so that the top of the jack contacts the
vehicle at the jack-up point.
The jack should be placed on firm level
ground.
2. Align the jack head between the two notches
located at the jack-up point of either the front or
the rear section.
3. Fit the groove of the jack head between the
notches as shown.
4. Loosen each wheel nut, counterclockwise, one or
two turns with the wheel nut wrench.
Do not remove the wheel nuts until the tire is
off the ground.
5. Carefully raise the vehicle until the clearance
between the tire and ground is achieved.
6. To lift the vehicle, securely hold the jack lever and
rod with both hands and turn the jack lever.
Removing tire
GUID-FFA0175C-16AD-4679-BFC7-EDC03785107C
1. Remove the wheel nuts.
2. Remove the damaged tire.
CAUTION:
The tire is heavy. Be sure that your feet are clear
from the tire and use gloves as necessary to
avoid injury.
Installing spare tire
GUID-A275BDB2-CC15-43EA-ADD5-F04791973386
SCE0576
WARNING:
. Never use wheel nuts which are not provided
with your vehicle. Incorrect wheel nuts or
improperly tightened wheel nuts may cause
the wheel to become loose or come off. This
could cause an accident.
. Never use oil or grease on the wheel studs
or nuts. This may cause the wheel nuts to
become loose.
. The temporary-use spare tire is designed for
emergency use only.
1. Clean any mud or dirt from the surface between
the wheel and hub.
2. Carefully put the spare tire on and tighten the
wheel nuts with your fingers. Check that all the
wheel nuts contact the wheel surface horizontally.
3. Tighten the wheel nuts alternately and evenly,
more than 2 times in the sequence illustrated (
*
1
-
*
4
), with the wheel nut wrench, until they are
tight.
4. Lower the vehicle slowly until the tire touches the
ground.
5. Tighten the wheel nuts securely, with the wheel
nut wrench, in the sequence illustrated.
6. Lower the vehicle completely.
Tighten the wheel nuts to the specified torque
with a torque wrench as soon as possible.
Wheel nut tightening torque:
108 N·m (11 kg-m, 80 ft-lb)
The wheel nuts must be kept tightened to
specification at all times. It is recommended
that the wheel nuts be tightened to specification
at each lubrication interval.
In case of emergency 6-5
6-6 In case of emergency
WARNING:
Retighten the wheel nuts when the vehicle has
been driven for 1,000 km (600 miles). (also in
cases of a flat tire, etc.)
Stowing damaged tire and tools
GUID-95F77D51-0936 -4657-AAE7-1FFA757699C7
WARNING:
. Be sure that the tire, jack and tools used are
properly stored after use. Such items can
become dangerous projectiles in an accident
or sudden stop.
. The temporary-use spare tire is designed for
emergency use only.
1. Securely store the damaged tire, jack and tools
used in the storage area.
2. Replace the spare tire cover and the floor cover.
3. Close the back door.
REPAIRING FLAT TIRE (for model with
emergency tire puncture repair kit)
GUID-D0EE414F-945A-41AA-B302-206031120911
The emergency tire puncture repair kit is supplied with
the vehicle instead of a spare tire. This repair kit must
be used for temporarily fixing a minor tire puncture.
After using the repair kit, see a NISSAN dealer as soon
as possible for tire inspection and repair/replacement.
CAUTION:
. NISSAN recommends using only Genuine
NISSAN Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can cause
the tire to lose air pressure.
. Do not use the emergency tire puncture
repair kit provided with your vehicle on other
vehicles.
. Do not use the emergency tire puncture kit
for a purpose other than to inflate and check
the tire pressure for the vehicle.
. Use the emergency tire puncture kit only on
DC12V.
. Keep water and dust off the emergency tire
puncture kit.
. Do not disassemble or modify the emer-
gency tire puncture kit.
. Do not galvanize the emergency tire punc-
ture kit.
. Do not use the emergency tire puncture
repair kit under the following conditions.
Contact a NISSAN dealer or professional
road assistance.
— when the sealant has passed its expira-
tion date (shown on the label attached
to the bottle)
— when the cut or the puncture is approxi-
mately 6 mm (0.25 in) or longer
— when the side of the tire is damaged
— when the vehicle has been driven with a
considerable loss of air from the tire
— when the tire is completely displaced
inside or outside the rim
— when the tire rim is damaged
— when two or more tires are flat
Getting emergency tire puncture repair kit
GUID-B6E13148-6E 43-4DC4-95FC-C420C3349127
SCE0895
Take out the emergency tire puncture repair kit from
the back door. The repair kit consists of the following
items:
*
1
Tire sealant bottle
*
2
Air compressor
*
3
Speed restriction sticker
Before using emergency tire puncture repair
kit
GUID-E1A41089-DC64-4DB7-B341-573467134588
. If any foreign object (for example, a screw or nail)
is embedded in the tire, do not remove it.
. Check the expiration date of the sealant (shown
on the label attached to the bottle). Never use a
sealant whose expiration date has passed.
Repairing tire
GUID-0BDF41CB-1B07-43BA-8DDA-5F25BD5E79BF
WARNING:
Observe the following precautions when using
the emergency tire puncture kit.
. Swallowing the compound is dangerous.
Immediately drink as much water as possi-
ble and seek prompt medical assistance.
. Rinse well with lots of water if the com-
pound comes into contact with skin or eyes.
If irritation persists, seek prompt medical
attention.
. Keep the repair compound out of the reach
of children.
. The emergency repair compound may cause
a malfunction of the air valve. Have the air
valve replaced as soon as possible.
SCE0867
1. Open the lid of the air compressor and take out
the speed restriction sticker, then put it in a
location where the driver can see it while driving.
CAUTION:
Do not put the speed restriction label on the
steering wheel pad, the speedometer or the
warning light locations.
SCE0868
2. Take the hose
*
1
and the power plug
*
2
out of
the air compressor. Remove the cap of the bottle
holder from the air compressor.
SCE0869
3. Remove the cap of the tire sealant bottle, and
screw the bottle clockwise onto the bottle holder.
(Leave the bottle seal intact. Screwing the bottle
onto the bottle holder will pierce the seal of the
bottle.)
4. Remove the cap of the tire valve on the flat tire.
SCE0870
5. Remove the protective cap
*
A
of the hose and
screw the hose securely onto the tire valve. Make
sure that the pressure release valve
*
B
is
securely tightened. Make sure that the air com-
pressor switch is in the OFF (
) position, and
then insert its power plug into the power outlet in
the vehicle.
In case of emergency 6-7
6-8 In case of emergency
SCE0871
6. 6. Push the ignition switch to the “ACC” position.
Then turn the compressor switch to the ON (−)
position and inflate the tire up to the pressure that
is specified on the tire placard affixed to the
driver’s side center pillar if possible, or to the
min imum of 180 kPa (26 psi). Turn the air
compressor off briefly in order to check the tire
pressure with the pressure gauge.
If the tire is inflated to higher than the specified
pressure, adjust the tire pressure by releasing air
with the pressure release valve. The cold tire
pressures are shown on the tire placard affixed to
the driver’s side center pillar.
CAUTION:
. An incomplete connection between the hose
and tire valve causes air leakage or sealant
scatter.
. Do not stand directly beside the damaged
tire while it is being inflated because of the
risk of the rupture. If there are any cracks or
bumps, turn the compressor off immedi-
ately.
. There is a possi bility that the pressure
reaches 600 kPa while the tire is being
inflated, but it is normal condition. Usually
the pressure will drop in about 30 seconds.
. Do not operate the compressor for more
than 10 minutes.
If the tire pressure does not increase to 180 kPa
(26 psi) within 10 minutes, the t ire may be
seriously damaged and the tir e cannot be
repaired with this tire repair kit. Contact a
NISSAN dealer.
7. When the tire pressure is reaching the specified
pressure or is at the minimum of 180 kPa (26 psi),
turn the air compressor off. Remove the power
plug from the power outlet and quickly remove the
hose from the tire valve. Attach the protective cap
and valve cap.
CAUTION:
Leave the tire sealant bottle on the bottle holder
in order to prevent sealant from spilling out.
8. Immediately drive the vehicle for 10 minutes or 3
km (2 miles) at a speed of 80 km/h (50 MPH) or
less.
9. After driving, make sure that the air compressor
switch is in the OFF position, then screw the hose
securely onto the tire valve. Check the tire
pressure with the pressure gauge. The temporary
repair is completed if the tire pressure does not
drop.
Make sure the pressure is adjusted to t he
pressure that is specified on the tire placard
before driving.
10. If the tire pressure drops, repeat the steps from 5.
If the pressure drops again or under 130 kPa (19
psi), the tire cannot be repaired with this tire repair
kit. Contact a NISSAN dealer.
CAUTION:
Do not reuse the tire sealant bottle or the hose.
For a new tire sealant bottle and hose, see a
NISSAN dealer.
After repairing tire
GUID-52CAAEB6-544 F-47BF-B8AB-2A348A9FC39C
See a NISSAN dealer for tire repair/replacement as
soon as possible.
GUID-E4D85193-CD36-4C13-A769-57184268F3FB
WARNING:
. Incorrect jump starting can lead to a battery
explosion. The battery explosion may result
in severe injury or death. It may also result in
damage to the vehicle. Be sure to follow the
instructions in this section.
. Explosive hydrogen gas is always present in
the vicinity of the battery. Keep all sparks
and flames away from the battery.
. Always wear suitable eye protection and
remove rings, bracelets, and any other jew-
elry whenever working on or near a battery.
. Never lean o ver the battery while jump
starting.
. Never allow battery fluid to come into
contact with eyes, skin, clothes or the
vehicle’s painted surfaces. Battery fluid is a
corrosive sulf uric acid which can cause
severe burns. If the fluid comes into contact
with anything, immediately flush the con-
tacted area with plenty of water.
. Keep the battery out of the reach of children.
. The booster battery must be rated at 12
volts. Use of an incorrectly rated battery will
damage your vehicle.
. Never attempt to jump start a frozen battery.
It could explode and cause serious injury.
JVE0111X
HR12DDR engine model
JVE0112X
HR12DE and HR15DE engine model
JVE0113X
K9K engine model
1. If the booster battery is in another vehicle
*
B
,
position the two vehicles
*
A
and
*
B
to bring the
batteries into close proximity to each other.
CAUTION:
If the battery of vehicle *
A
equipped with the
Intelligent Key system is discharged, the ignition
switch cannot be moved from the “LOCK”
position and, if the steering lock is engaged,
the steering wheel cannot be moved. Connect
the jumper cables to the booster vehicle
*
B
before turning the ignition switch and disenga-
ging the steering lock.
2. Apply the parking brake.
3. Automatic Transmission (AT)/Continuously Vari-
able Transmission (CVT) model: Move the shift
lever to the “P” (Park) position.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) position.
4. Switch off all unnecessary electrical systems
(headlights, heater, air conditioner, etc.).
5. Turn the ignition switch to the “LOCK” position.
6. Remove the vent caps, if equipped, on the battery.
7. Cover the battery with a firmly wrung out moist
cloth to reduce the hazard of an explosion.
8. Connect the jumper cables in the sequence as
illustrated (
*
1
,
*
2
,
*
3
,
*
4
).
CAUTION:
. Always connect positive + to positive + and
negative 7 to body ground, NOT to the
battery’s negative 7.
In case of emergency 6-9
JUMP STARTING
6-10 In case of emergency
. Be sure that the jumper cables do not touch
moving parts in the engine compartment.
. Be sure that the jumper cable’s clamps do
not contact any other metal.
9. Start the engine of the booster vehicle
*
B
and let
it run for a few minutes.
10. Depress the accelerator pedal of the booster
vehicle
*
B
at about 2,000 rpm.
11. Start the engine of the jumped vehicle
*
A
in the
normal manner.
CAUTION:
. Never keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, turn the ignition switch
“OFF” and wait at least 10 seconds before
trying again.
. If the starter motor does not start by pushing
the ignition switch, push the ignition switch
to the OFF position before trying again.
12. After the engine is started, carefully disconnect
the jumper cables in the opposite sequence from
that illustrated (
*
4
,
*
3
,
*
2
,
*
1
).
13. Remove and dispose of the cloth as it may be
contaminated with corrosive acid.
14. Replace the vent caps, if removed.
NOTE:
. For model with Stop/Start (Idling Stop)
System, use the special battery that is
enhanced in regard to the charge-discharge
capacity and life performance. Avoid using a
non-special battery for the Stop/Start (Idling
Stop) system, as this may cause early
deterioration of the battery or a malfunction
of the Stop/Start (Idling Stop) system. For
the batter y, it is recommend ed to use
Genuine NISSAN parts. For more informa-
tion, contact a NISSAN dealer.
. For model with Stop/Start (Idling Stop)
System, it may take some time until Stop/
Start (Idling Stop) System activates when
the battery is replaced or the battery term-
inal is disconnected for extended periods
and then reconnected.
GUID-818A8DA5-53AB-4D7C-8EC2-4D904BE854C1
Do not attempt to start the engine by pushing the
vehicle.
CAUTION:
. Automatic Transmission (AT)/Continuously
Variable Transmission (CVT)/Manual Trans-
mission (MT) model cannot be started by
pushing. Attempting to do so may cause
damage to the transmission.
. Three-way catalyst equipped model should
not be started by pushing. Attempting to do
so may cause damage to the catalyst.
. Never try to start the engine by towing.
When the engine starts, the forward surge
could cause the vehicle to collide with the
towing vehicle.
. Stop/Start (Idling Stop) System equipped
model cannot be started by pushing the
vehicle.
PUSH STARTING
GUID-C9298AC9-81BF-4489-BAB5-7960058A83B6
WARNING:
. Never continue driving if your vehicle over-
heats. Doing so could cause a vehicle fire.
. Never open the hood if steam is coming out.
. Never remove the radiator cap while the
engine is hot. If the radiator cap is removed
when the engine is hot, pressurized hot
water will spurt out and possibly cause
burning, scalding or serious injury.
. If steam or coolant is coming from the
engine, stand clear of the vehicle to prevent
getting burned.
. Be careful not to allow your hands, hair,
jewelry or clothing to come into contact with,
or to get caught in the cooling fan or drive
belts. The engine cooling fan will start at any
time.
If your vehicle is overheating (indicated by the high
temperature indicator), or if you feel a lack of engine
power, detect unusual noise, etc., take the following
steps:
1. Safely move the vehicle off the road away from
traffic.
2. Turn on the hazard indicator flasher lights.
3. Apply the parking brake.
4. Automatic Transmission (AT)/Continuously Vari-
able Transmission (CVT) model: Move the shift
lever to the “P” (Park) position.
Manual Transmission (MT) model: Move the shift
lever to the “N” (Neutral) position.
DO NOT STOP THE ENGINE.
5. Open all windows.
6. Turn off the air conditioner. Set the temperature
control to maximum hot and fan control to
maximum speed.
7. Get out from the vehicle.
8. Visually inspect and listen for steam or coolant
escaping from the radiator before opening the
hood. Wait until no steam or coolant can be seen
before proceeding.
9. Open the engine hood.
10. Visually inspect if the cooling fan is running.
11. Visually inspect the radiator and radiator hoses for
leakage.
If the cooling fan is not running or the coolant is
leaking, stop the engine.
12. After the engine cools down, check the coolant
level in the reservoir with the engine running. Do
not open the radiator cap.
13. Add coolant to the reservoir if necessary.
Have your vehicle inspected/repaired at a NISSAN
dealer.
GUID-8FA77F15-7C1E-4AD5-A5EB-CAF67686534E
When towing your vehicle, local regulations for towing
must be followed. Incorrect towing equipment could
damage your vehicle. To assure proper towing and to
prevent accidental damage to your vehicle, NISSAN
recommends that you have professional road assis-
tance personnel tow your vehicle. It is advisable to
have the professional road assistant carefully read the
following precautions.
TOWING PRECAUTIONS
GUID-A0799369-1BB6-4E14-9D83-7762C2383337
. Be sure that the transmission, steering system and
powertrain are in working condition before towing.
If any units are damaged, the vehicle must be
towed using a dolly or flatbed tow truck.
. NISSAN recommends that your vehicle be towed
with the driving (front) wheels off the ground.
In case of emergency 6-11
IF YOUR VEHICLE OVERHEATS TOWING YOUR VEHICLE
6-12 In case of emergency
TOWING RECOMMENDED BY NISSAN
GUID-6BE95DF9-946D -4CD6-A782-B9B7735487A2
Towing Two-Wheel Drive (2WD) model
GUID-803D2CC8-D00F-4E67-980A-2F9C265F1AED
SCE0613
SCE0614
NISSAN recommends that towing dollies be used
under the front wheels when towing your vehicle or the
vehicle be placed on a flatbed tow truck as illustrated.
Front wheels on the ground:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
CAUTION:
Never tow Automatic Transmission (AT)/Con-
tinuously Variable Transmission ( CVT) model
with the front wheels on the ground. Doing so
will cause serious and expensive damage to the
drivetrain.
Manual Transmission (MT) model:
1. Place the ignition switch in the “OFF” position.
2. Secure the steering wheel in a straight-ahead
position with rope or a similar device.
3. Move the shift lever to the “N” (Neutral) position.
4. Release the parking brake.
5. Attach safety chains whenever towing.
Rear wheels on the ground:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. Place the ignition switch to the “OFF” position.
2. Secure the steering wheel in a straight-ahead
position with rope or a similar device.
3. Move the shift lever to the “N” (Neutral) position.
4. Release the parking brake.
5. Attach safety chains whenever towing.
All four wheels on the ground:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
CAUTION:
Never tow AT/CVT model with all four wheels on
the ground. Doing so will cause serious and
expensive damage to the transmission.
Manual Transmission (MT) model:
1. Place the ignition switch in the “OFF” position.
2. Move the shift lever to the “N” (Neutral) position.
3. Release the parking brake.
Freeing trapped vehicle
GUID-ADCE0525-7CD3-4598-8D15-CC604F725BA2
WARNING:
. Never allow anyone to stand near the towing
line during the pulling operation.
. Never spin the tires at high speed. This could
cause them to explode and result in serious
injury. Parts of the vehicle could also over-
heat and be damaged.
. Do not pull the vehicle using the rear hook.
The rear hook is not designed to pull the
vehicle out in the event that the vehicle
becomes trapped.
In the event that your vehicle’s tires become trapped in
sand, snow, or mud, and the vehicle is unable to free
itself without being pulled, use the recovery hooks.
. Use the recovery hooks only. Do not attach the
pulling device to any other part of the vehicle body.
Otherwise, the vehicle body may be damaged.
. Use the recovery hooks to free a vehicle only.
Never tow a vehicle using only the recovery hooks.
. The recovery hooks are under tremendous stress
when used to free a trapped vehicle. Always pull
the pulling device straight out from the vehicle.
Never pull on the recovery hooks at an angle.
Front :
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SCE0905
Type A (except for Sports version)
JVE0114X
Type B (except for Sports version)
In case of emergency 6-13
6-14 In case of emergency
SCE0943
Type C (for Sports version)
*
1
Remove the hook cover from the bumper with a
suitable tool.
*
2
Securely install the recovery hook as illustrated.
(The hook is stored with the jacking tools.)
Make sure that the recovery hook is properly secured
in its storage area after use.
Rear:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SCE0906
Rear
Do not use the hook to tow the vehicle.

Related Topics

Popular Owner Manuals