2004-2009 Nissan Micra 4 Door Safety ? seats, seat belts and supplemental restraint system -> Child restraints User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Safety ? seats, seat belts and supplemental restraint system -> Child restraints for Your Nissan Micra 4 Door Third Generation (2004-2009)

2. Adjust the seat belt length. To shorten, hold the
tongue and pull the upper belt as illustrated
*
1
.
To lengthen, hold the tongue and pull the under
belt as illustrated
*
2
.
SSS0450
3. Position the lap belt portion low and snug on the
hips as shown.
Unfastening seat belts
GUID-83362DBC-05D2-4411-A0F9-92FAFF26E5F2
Push the button on the buckle.
SEAT BELT MAINTENANCE
GUID-3C96CF89-85AF-428C-8071-11B0DAEFED38
Periodically check that the seat belt and all the metal
components, such as buckles, tongues, retractors,
flexible wires and anchors, work properly. If loose parts,
deterioration, cuts or other damage on the seat belt
webbing is found, the entire seat belt assembly should
be replaced.
If dirt builds up in the shoulder belt guide of the seat
belt anchors, the seat belts may retract slowly. Wipe
the shoulder belt guide with a clean, dry cloth.
To clean the seat belt webbing, apply a mild soap
solution or any solution recommended for cleaning
upholstery or carpet. Then wipe with a cloth and allow
the seat belts to dry in the shade. Do not allow the seat
belts to retract until they are completely dry.
GUID-D1B3B6D7-C7D7-4753-91EE-75DF2C345A 8F
PRECAUTIONS ON CHILD RESTRAINT
USAGE
GUID-84539F71-07B4-4992-B051-160D792D0591
SSS0099
WARNING:
. Infants and small children should never be
carried on your lap. It is not possible for even
the strongest adult to resist the forces of a
severe accident. The child could be crushed
between the adult and parts of the vehicle.
Also, it is dangerous to put a seat belt
around a child being carried on the occu-
pant’s lap.
. Infants and children need special protection.
The vehicle’s seat belts may not fit them
properly. The shoulder belt may come too
close to the face or neck. The lap belt may
not fit over their small hip bones. In an
accident, an improperly fitting seat belt
could cause serious or fatal injury.
. Infants and small children should always be
placed in an appropriate child restraint
system while riding in the vehicle. Failure
to use a child restraint system can result in
serious injury or death.
. Child restraint systems specially designed
for infants and small children are available
from several manufacturers. When selecting
any child restraint systems, place your child
in the child restraint system and check the
various adjustments to be sure that the child
restrain t system is compatible with your
child. Always follow the manufacturer’s in-
structions for installation and use.
. NISSAN recommends that the child restraint
system be installed in the rear seat. Accord-
ing to accident statistics, children are safer
when properly restrained in the rear seat
rather than in the front seat.
. Follow all of the child restraint system
manufacturer’s instructions for installation
and use. When purchasing a child restraint
system, be sure to select one which will fit
your child and vehicle. It may not be possible
to prop erly install some types of chi ld
restraint systems in your vehicle.
. For a front-facing child restraint system,
check to make sure the shoulder belt does
not fit close to child’s face or neck. If it does,
put the shoulder belt beh ind the child
restraint system.
. Never install a rear-f a c i n g child restraint
system in the front seat. An inflating supple-
mental front-impact air bag could seriously
injure or kill your child. A rear-facing child
restraint system must only be used in the
rear seat.
. Adjustable seatbacks should be positioned
to fit a child restraint system, but as upright
as possible.
Safety — seats, seat belts and supplemental restraint system 1-13
CHILD RESTRAINTS
1-14 Safety — seats, seat belts and supplemental restraint system
. If the seat belt in the position where a child
restraint system is installed requires a lock-
ing clip and if it is not used, injuries could
result from a child restraint system tipping
over during normal vehicle braking or cor-
nering.
. After attaching a child restraint system, test
it before you place the child in it. Tilt it from
side to side. Try to tug it forward and check if
it is held securely in place. The child restraint
system should not move more than 25 mm (1
in). If the restraint is not secure, tighten the
belt as necessary, or install the restraint in
another seat and test it again.
. Check the child restraint system in your
vehicle to be sure that it is compatible with
the vehicle’s seat belt system.
. If a child restraint system is not anchored
properly, the risk of a child being injured in a
collision or a sudden stop greatly increases.
. Improper use of a child restraint system can
increase the risk or severity of injury for both
the child and other occupants in the vehicle.
. Always use an appropriate child restraint
system. An improperly installed child re-
straint system could lead to serious injury
or death in an accident.
. When the child restraint system is not in use,
keep it secured with the I SOFIX child
restraint system (if equipped) or a seat belt
to prevent it from being thrown around in
case of a sudden stop or accident.
NISSAN recommends that infants and small children
be seated in a child restraint system. You should
choose a child restraint system that fits your vehicle
and always follow the manufacturer’s instructions for
installation and use. In addition, there are many types
of child restraint systems available for larger children
that should be used for maximum protection.
CAUTION:
Remember that a child restraint system left in a
closed vehicle can become very hot. Check the
seating surface and buckles before placing your
child in a child restraint system.
UNIVERSAL CHILD RESTRAINTS FOR
FRONT SEAT AND REAR SEATS (for Europe
and Ukraine)
GUID-D5C9B1DE-3E97-4308-9494-C83310B63EDB
When selecting any child restraint, keep the following
points in mind:
. Choose a child restraint that complies with the
latest European safety standard, ECE Regulation
44.04.
. Place your child in the child restraint and check
the various adjustments to be sure the child
restraint is compatible with your child. Always
follow all of the recommended procedures.
. Check the child restraint in your vehicle to be sure
it is compatible with vehicle’s seat belt system.
. Refer to the tables later in this section for a list of
the recommended fitment posit ions and the
approved child restraints for your vehicle.
Approved child restraint positions (models without ISOFIX)
GUID-4B47FC71-C923-4A4B-BA9B-60CBF9C83F5E
Seating position
Weight group Front passenger
Rear (Single folding) Rear (Tumble)
Right Centre Left Right Centre Left
0 (<10 kg) X L L L L L L
0 +(<13 kg) X L L L L L L
I (9 to 18 kg) UF L X L L L X
II (15 to 25 kg) UF L L L L L L
III (22 to 36 kg) UF L L L L L
L
X: Not suitable for child restraint system.
UF: Suitable for forward-facing (FWF) universal category child restraint system approved for this group.
L: Suitable for the particular child restraints provided in the following table.
Safety — seats, seat belts and supplemental restraint system 1-15
1-16 Safety — seats, seat belts and supplemental restraint system
List of approved child restraints
GUID-070BD51F-02D9-4526-A915-CE48597D6CFA
Weight group
Name of CRS
Facing position Category
0 to 13 kg
Britax/RO
¨
MER BABY-
SAFE
Rear-facing Universal
9 to 18 kg Britax/RO
¨
MER DUO plus Front-facing Universal
9 to 18 kg Fair GO/1S Front-facing Universal
15 to 36 kg Britax/RO
¨
MER Kid Front-facing
Universal
Approved child restraint positions (models with ISOFIX)
GUID-16DC236E-5C84-4D51-AAF9-693CBD62AC7C
The following restrictions are applied when using child restraints varying by infants weight and installation position
(ISOFIX child restraint):
Weight group
Seating position
Rear outer
Carry-cot
F ISO/L1
X
G ISO/L2
X
0 (<10 kg)
E ISO/R1
X
0+ (<13 kg)
E ISO/R1
X
D ISO/R2
X
C ISO/R3
IL
I (9 to 18 kg)
D ISO/R2
X
C ISO/R3
IL
B ISO/F2
IUF
B1 ISO/F2X
IUF, IL
A ISO/F3
IUF
II (15 to 25 kg)
-
X
III (22 to 36 kg)
-
X
X: Not suitable for child restraint system.
IUF: Suitable for forward-facing (FWF) universal category child restraint system approved for this group.
IL: Suitable for the particular ISOFIX category child restraint systems (CRS) provided in the following table.
These ISOFIX CRS are those of the specific vehicle, restricted or semi-universal categories.
List of approved child restraints
GUID-12703704-BED5-4EAC-AE9B-9CDEEF14A8EF
Weight group Size class Name of CRS Fixture of CRS Facing position Category
0 to 18 kg C Fair GO/1S
ISO/R3 support
frame (type A)
Rear-facing Semi-Universal
9 to 18 kg B1
Britax/RO
¨
MER
DUO plus
ISO/F2X top
tether
Front-facing*
Universal
*Front facing: from 2 years only with headrest.
WARNING:
In vehicles equipped with a side air bag system,
do not let any infants or small children sit in the
front passenger’s seat as the air bag may cause
serious injury in case of deployment during a
collision.
NOTE:
Child restraints approved to ECE Regulation NO.
44.04 are clearly marked with the categories
such as Universal, Semi-universal or ISOFIX.
ISOFIX CHILD RESTRAINT SYSTEM (if
equipped)
GUID-7DAC36F2-E2B9-493B-B926-2FCB2F3D83C1
Your vehicle is equipped with special anchor points
that are used with ISOFIX child restraint systems.
ISOFIX lower anchor point locations
GUID-A8304ACD-7914-45BF-924C-ABC30FC91996
The ISOFIX anchor points are provided to install child
restraints in the rear outboard seating positions only.
Do not attempt to install a child restraint in the
center position using the ISOFIX anchors.
SSS1046
ISOFIX label location
Safety — seats, seat belts and supplemental restraint system 1-17
1-18 Safety — seats, seat belts and supplemental restraint system
SSS0637
ISOFIX lower anchor location
The ISOFIX anchors are located at the rear of the seat
cushion near the seatback. A label is attached to the
seatback to help you locate the ISOFIX anchors.
ISOFIX child restraint anchor attachments
GUID-9DE17E3D-A48B-4832-8C7E-D39C3F2B3236
SSS0644
Anchor attachment
ISOFIX child restraints include two rigid attachments
that can be connected to two anchors located in the
seat. With this system, you do not have to use a vehicle
seat belt to secure the child restraint. Check your child
restraint for a label stating that it is compatible with the
ISOFIX child restraints. This information may also be in
the instructions provided by the child restraint manu-
facturer.
ISOFIX child restraints generally require the use of a
top tether strap or other anti-rotation devices such as
support legs. When installing ISOFIX child restraints,
carefully read and follow the instructions in this manual
and those supplied with the child restraints. (See
“Child restraint installation using ISOFIX” (P.1-19).)
CHILD RESTRAINT ANCHORAGE (if
equipped)
GUID-9CBC9A3C-37A6-490D-BE0C-8F53A4EF3D3A
Your vehicle is designed to accommodate a child
restraint system on the rear seat. When installing a
child restraint system, carefully read and follow the
instructions in this manual and those supplied with the
child restraint system.
WARNING:
. Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstances are they to be used for adult
seat belts, harnesses or for attaching other
items or equipment to the vehicle.
. The child restraint top tether strap may be
damaged by contact with the cargo cover or
items in the luggage area. Remove the cargo
cover from the vehicle or secure it and any
luggage. Your chi ld could be s eriously
injured or killed in a collision if the top
tether strap is damaged.
Anchorage location
GUID-B23FAAE8-F2E4-4ACA-9459-2381DF4D41E9
JVR0001X
The anchor points are located on the seat behind the
rear seats outboard seating positions.
JVR0009X
For Australia and New Zealand
The center anchorage (if equipped) is located on the
back door opening.
CHILD RESTRAINT INSTALLATION USING
ISOFIX
GUID-BCBDE462-22A7-4AF3-BE55-6633F83BDD27
WARNING:
. Attach ISOFIX child restraints only at the
specified locations. For the ISOFIX lower
anchor locations, see “ISOFIX child restraint
system” (P.1-17). If a child restraint is not
secured properly, your child could be ser-
iously injured or killed in an accident.
. Do not install child restraints that require the
use of a top tether strap to seating positions
that do not have a top tether anchor.
. Do not secure a child restraint in the center
rear seating position using the ISOFIX lower
anchors. The child re straint will not be
secured properly.
. Inspect the lower anchors by inserting your
fingers into the lowe r anchor area and
feeling to make sure there are no obstruc-
tions over the ISOFIX anchors, such as seat
belt webbing or seat cushion material. The
child restraint will not be secured properly if
the ISOFIX anchors are obstructed.
. Child restraint anchorages are designed to
withstand only those loads imposed by
correctly fitted child restraints. Under no
circumstance are they to be used for adult
seat belts, harnesses or for attaching other
items or equipment to the vehicle.
Installation on rear outboard seats
GUID-EBA567E6-B179-4045-AE2A-CE4765ED2602
Front-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Be sure to follow the manufacturer’s instructions for
the proper use of your child restraint. Follow these
steps to install a front-facing child restraint on the rear
outboard seats using ISOFIX:
SSS0646A
Steps 1 and 2
1. Position the child restraint on the seat
*
1
.
2. Secure the child restraint anchor attachments to
the ISOFIX lower anchors
*
2
.
3. The back of the child restraint should be secured
against the vehicle seat back. If necessary, adjust
or remove the head restraint to obtain the correct
child restraint fit. (See “Head restraints” (P.1-5).) If
the head restraint is removed, store it in a secure
place. Be sure to install the head restraint when
the child restraint is removed. If the seating
position does not have an adjustable head
restraint and it is interfering with the proper child
restraint fit, try another seating position or a
different child restraint.
SSS0754A
Step 4
4. Shorten the rigid attachment to have the child
restraint firmly tightened; press downward
*
3
and rearward
*
4
firmly in the center of the child
restraint with your knee to compress the vehicle
seat cushion and seatback.
5. If the child restraint is equipped with a top tether
strap, route the top tether strap and secure the
tether strap to the tether anchor point. (See “Child
restraint anchorage” (P.1-18).)
6. If the child restraint is equipped with other anti-
rotation devices such as support legs, use them
instead of the top tether strap following the child
restraint manufacturer’s instructions.
Safety — seats, seat belts and supplemental restraint system 1-19
1-20 Safety — seats, seat belts and supplemental restraint system
SSS0755A
Step 7
7. Test the child restraint before you place the child
in it
*
5
. Push the child restraint from side to side
and tug it forward to make sure that it is held
securely in place.
8. Check to make sure that the child restraint is
properly secured prior to each use. If the child
restraint is loose, repeat steps 3 through 7.
Rear-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Be sure to follow the manufacturer’s instructions for
the proper use of your child restraint. Follow these
steps to install a rear-facing child restraint on the rear
outboard seats using ISOFIX:
SSS0649A
Steps 1 and 2
1. Position the child restraint on the seat
*
1
.
2. Secure the child restraint anchor attachments to
the ISOFIX lower anchors
*
2
.
SSS0756A
Step 3
3. Shorten the rigid attachment to have the child
restraint firmly tightened; press downward
*
3
and rearward
*
4
firmly in the center of the child
restraint with your hand to compress the vehicle
seat cushion and seatback.
4. If the child restraint is equipped with a top tether
strap, route the top tether strap and secure the
tether strap to the tether anchor point. (See “Child
restraint anchorage” (P.1-18) .)
5. If the child restraint is equipped with other anti-
rotation devices such as support legs, use them
instead of the top tether strap following the child
restraint manufacturer’s instructions.
SSS0757A
Step 6
6. Test the child restraint before you place the child
in it
*
5
. Push the child restraint from side to side
and tug it forward to make sure that it is held
securely in place.
7. Check to make sure that the child restraint is
properly secured prior to each use. If the child
restraint is loose, repeat steps 3 through 6.
CHILD RESTRAINT INSTALLATION USING
SEAT BELT
GUID-D2F6DA79-3BC2-497B-A19A-D27CCCA06FA2
Installation on rear outboard seats - seat belts
without automatic locking mode
GUID-2745B2E8-E5 36-400E-AEB7-FCDE2FB2D5BB
WARNING:
. The three-point type seat belt on your
vehicle is not equipped with an automatic
locking mode retractor.
. The direction of the child restraint system
depends on the type of the child restraint
system and the size of the child.
If your vehicle is equipped with rear seat adjustment,
note the following:
. Attach the child restraints after adjusting the
rear seats to the upright position.
. Do not recline the rear seats with the child
restraints attached to them.
Front-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SSS0374A
If you must install a front-facing child restraint system
on the rear seat, follow these steps:
1. Position the front-facing child restraint system on
the rear seat.
Always follow the child restraint system manufac-
turer’s instructions for installation and use.
2. Route the seat belt tongue through the child
restraint system and insert it into the buckle until
you hear and feel the latch engage.
SSS0513
To prevent slack in the lap belt, it is necessary to
secure the shoulder belt in place with a locking
clip
*
A
. Use the locking clip attached to the child
restraint system or one which is equivalent in
dimension and strength.
Be sure to follow the child rest raint sys tem
manufacturer’s instructions for belt routing.
3. Test the child restraint system before you place
the child in it. Tilt it from side to side. Try to tug it
forward and check if it is held securely in place.
4. Make sure that the child restraint system is
properly secured prior to each use.
Rear-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SSS0375A
If you must install a rear-facing child restraint system
on the rear seat, follow these steps:
1. Position the rear-facing child restraint system on
the rear seat.
Always follow the child restraint system manufac-
turer’s instructions for installation and use.
2. Route the seat belt tongue through the child
restraint system and insert it into the buckle until
you hear and feel the latch engage.
SSS0513
To prevent slack in the lap belt, it is necessary to
secure the shoulder belt in place with a locking
Safety — seats, seat belts and supplemental restraint system 1-21
1-22 Safety — seats, seat belts and supplemental restraint system
clip
*
A
. Use the locking clip attached to the child
restraint system or one which is equivalent in
dimension and strength.
Be sure to follow the child rest raint sys tem
manufacturer’s instructions for belt routing.
3. Test the child restraint system before you place
the child in it. Tilt it from side to side. Try to tug it
forward and check if it is held securely in place.
4. Make sure that the child restraint system is
properly secured prior to each use.
Installation on rear center seat (2-point type
seat belt)- seat belts without automatic
locking mode
GUID-E8AB11EC-7449-4C6A-A48E-FD9CEBA5CE3B
WARNING:
. The rear center two-point type seat belt on
your vehicle is not equipped with an auto-
matic locking mode retractor.
. The direction of the child restraint system
depends on the type of the child restraint
system and the size of the child.
Front-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SSS0512
If you must install a front-facing child restraint system
on the rear center seat, follow these steps:
1. Position the front-facing child restraint system on
the rear center seat.
Always follow the child restraint system manufac-
turer’s instructions for installation and use.
2. Route the seat belt tongue through the child
restraint system and insert it into the buckle until
you hear and feel the latch engage.
SSS0513
Locking clip
3. To prevent slack in the lap belt, it is necessary to
secure the lap belt in place with a locking clip
*
A
.
Use the locking clip attached to the child restraint
system, or one which is equivalent in dimensions
and strength.
Be sure to follow the child rest raint sys tem
manufacturer’s instructions for belt routing.
4. Test the child restraint system before you place
the child in it. Tilt it from side to side. Try to tug it
forward and check if it is held securely in place.
5. Make sure that the child restraint system is
properly secured prior to each use.
Rear-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SSS0514
If you must install a rear-facing child restraint system
on the rear center seat, follow these steps:
1. Position the rear-facing child restraint system on
the rear center seat.
Always follow the child restraint system manufac-
turer’s instructions for installation and use.
2. Route the seat belt tongue through the child
restraint system and insert it into the buckle until
you hear and feel the latch engage.
SSS0513
Locking clip
3. To prevent slack in the lap belt, it is necessary to
secure the lap belt in place with a locking clip
*
A
.
Use the locking clip attached to the child restraint
system, or one which is equivalent in dimensions
and strength.
Be sure to follow the child rest raint sys tem
manufacturer’s instructions for belt routing.
4. Test the child restraint system before you place
the child in it. Tilt it from side to side. Try to tug it
forward and check if it is held securely in place.
5. Make sure that the child restraint system is
properly secured prior to each use.
Installation on front seat - seat belts without automatic locking mode
GUID-48CF52C1-AED2-4536-89C6-01204BD1A763
SSS0300A
WARNING:
. Never install a rear-facing child restraint on
the front passenger’s seat when the front
passenger’s air bag is equipped. Supple-
mental front-impact air bags inflate with
great force. A rea r-facing child restraint
could be struck by the supplemental front-
impact air bags in an accident and could
seriously injure or kill your child.
. Never install a child restraint system with a
top tether strap on the front seat.
. NISSAN recommends that a child restraint
system be installed on the rear seat. How-
ever, if you must install a front-facing child
restraint system on the front passenger’s
seat, move the passenger’s seat to the
rearmost position.
. Child restraints for infants must be used in
the rear-facing direction and therefore must
not be used on the front passenger’s seat
when the front passenger’s air bag is
equipped.
Front-facing:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
SSS0627
If you must install a front-facing child restraint system
on the front seat, follow these steps:
1. Turn off the front passenger’s air bag using the
front passenger air bag switch. (See “Supple-
ment al air bag systems” (P.1-29)) P lace the
ignition switch in the “ON” position and make
sure that the front air bag status light
on the
meter illuminates (if equipped).
Safety — seats, seat belts and supplemental restraint system 1-23
1-24 Safety — seats, seat belts and supplemental restraint system
2. Move the seat to the rearmost position
*
1
.
3. Adjust the head restraint to its highest position
*
2
.
4. Position the front-facing child restraint system on
the front passenger’s seat. It should be placed in
the front-facing direction only.
Always follow the child restraint system manufac-
turer’s instructions for installation and use.
SSS0515
5. Route the seat belt tongue through the child
restraint system and insert it into the buckle until
you hear and feel the latch engage.
SSS0513
Locking clip
6. To prevent slack in the lap belt, it is necessary to
secure the shoulder belt in place with a locking
clip
*
A
. Use the locking clip attached to the child
restraint system, or one which is equivalent in
dimensions and strength.
Be sure to follow the child rest raint sys tem
manufacturer’s instructions for belt routing.
7. Slide the seat forward so that the seat belt fully
tightens the child restraint system.
8. Test the child restraint system before you place
the child in it. Tilt it from side to side. Try to tug it
forward and check if it is held securely in place.
9. Make sure that the child restraint system is
properly secured prior to each use.

Related Topics

Popular Owner Manuals