Get Do-it-yourself -> Lights Guide for Nissan Micra 4 Door Fifth Generation (2017-2023)

LIGHTS

∙

The key fob is water-resistant; how-

ever, if it does get wet, immediately

wipe completely dry.

For Canada:

HEADLIGHTS

For additional information on headlight

bulb replacement, refer to the instructions

outlined in this section.

This device complies with Industry

Canada licence-exempt RSS standard(s).

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must ac-

cept any interference, including interfer-

ence that may cause undesired opera-

tion of the device.

The operational range of the key fob

extends to approximately 10 m (33 ft)

from the vehicle. This range may vary

with conditions.

Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device

must accept any interference received,

including interference that may cause

undesired operation of the device.

FCC Notice:

For USA:

This device complies with Part 15 of the

FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interfer-

ence received, including interference

that may cause undesired operation.

Note:

Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s author-

ity to operate the equipment.

8-22 Do-it-yourself

the engine compartment without remov-

ing the headlight assembly.

1. Disconnect the battery negative cable.

A

2. Disconnect the electrical connector

from the rear end of the bulb.

᭺

CAUTION

B

3. Pull off the rubber cap

.

᭺

∙ High-pressure halogen gas is sealed

inside the bulb. The bulb may break if

the glass envelope is scratched or the

bulb is dropped.

C

4. Push and turn the retaining pin

loosen it.

to

᭺

5. Remove the headlight bulb. Do not

shake or rotate the bulb when remov-

ing it.

∙ Aiming should not be necessary after

replacing the H4 bulb. When aiming

adjustment is necessary, it is recom-

mended that you visit a NISSAN dealer

for this service.

6. Install the new bulb in the reverse order

of removal.

Fog may temporarily form inside the lens

of the exterior lights in the rain or in a car

wash. A temperature difference between

the inside and the outside of the lens

causes the fog. This is not a malfunction. If

large drops of water collect inside the lens,

it is recommended that you visit a NISSAN

dealer for servicing.

∙ Do not leave the headlight assembly

open without a bulb installed for a

long period of time. Dust, moisture,

smoke, etc. entering the headlight

body may affect bulb performance.

Remove the bulb from the headlight

assembly just before a replacement

bulb is installed.

∙ Only touch the base when handling

the bulb. Never touch the glass enve-

lope. Touching the glass could signifi-

cantly affect bulb life and/or head-

light performance.

JVM0002X

Replacing the halogen headlight

bulb

The headlight is a semi-sealed beam type

which uses a replaceable headlight (halo-

gen) bulb. They can be replaced from inside

∙ Use the same number and wattage as

shown in the chart.

Do-it-yourself 8-23

∙

Check that the fuel and lubricants levels

are filled to correct capacities.

Unload all luggage and other items,

which may influence the vehicle’s

height level.

∙

Load a weight on the driver’s seat that is

equivalent to the weight of a driver.

LDI2422

LDI2423

HEADLIGHT AIM

Stopping the vehicle

The aim of the headlights may require ad-

justment when replacing the headlight as-

sembly or when the vehicle’s front body

has been repaired. When the adjustment is

required, follow these procedures, or have

them adjusted by a NISSAN dealer.

1. Park the vehicle on a level surface verti-

cal to the wall or screen to which the

headlights will be projected.

2. Move the vehicle close to the wall to

determine the point P as shown in the

illustration.

Before performing the headlights aim ad-

justment:

The point P must be:

“H” is the distance between the head-

light’s center point to the level surface.

∙

Check the pressure of all tires for the

correct inflation pressure.

“WL” is the distance between the left

and right headlights’ centers.

∙

Check that the tools and spare tire are

stowed securely.

8-24 Do-it-yourself

3. Mark point P on the wall or screen.

4. Back up the vehicle 5,000 mm (197.0 in,

16.4 ft) straight away from the wall or

screen.

”L” is the distance between the wall or

screen to the vehicle’s front bumper.

5. Apply the parking brake.

LDI2979

NOTE:

Adjusting the headlight aim

The aim adjustment screws are located

Be sure that the vehicle is parked directly

vertical to the wall on which the headlights

will be projected.

on each side of the headlights. The lower

1

screw

is used to adjust the horizontal

2

᭺

aim. The upper screw

the vertical aim.

is used to adjust

᭺

1. Turn on the headlight low beam

2. Open the hood.

The screws can be turned indefinitely in

each direction. Therefore be sure to ob-

serve the headlight projection move-

ment to determine the necessary turn-

ing amount.

1

3. Turn the aiming adjustment screws

᭺

2

, located inside the engine compart-

᭺

ment, until the headlight projection, on

the wall or screen, does not move.

Do-it-yourself 8-25

1

4. Turn the lower screws

in the oppo-

᭺

CAUTION

site direction until the headlight projec-

tion becomes 70 mm (2.76 in) below the

point P. Once the left headlight has

been adjusted, perform right side ad-

justment as well.

∙ High pressure halogen gas is sealed

inside the halogen bulb. The bulb may

break if the glass envelope is

scratched or the bulb is dropped.

∙ When handling the bulb, do not touch

the glass envelope.

”C” is the distance between point P and

3

point

.

᭺

∙ Use the same number and wattage as

originally installed as shown in the

chart.

2

5. Turn the upper screws

in the oppo-

᭺

site direction until the horizontal head-

light projection’s turn point

rectly below the point P. Once the left

headlight has been adjusted, perform

right side adjustment as well.

3

is di-

᭺

∙ Do not leave the bulb out of the fog

light for a long period of time as dust,

moisture and smoke may enter the

fog light body and affect the perfor-

mance of the fog light.

FOG LIGHTS (if so equipped)

For additional information on fog light bulb

replacement, refer to the instructions out-

lined in this section.

Replacing the fog light bulb

If replacement is required, it is recom-

mended that you visit a NISSAN dealer for

this service.

8-26 Do-it-yourself

EXTERIOR AND INTERIOR LIGHTS

Item

Wattage (W)

Bulb No.*

Headlight assembly

High/Low/Daytime running light

Turn*

Park*

Side marker*

Fog light (if so equipped)*

Interior light

Cargo light

60/55

28

5

55

5

H4

3457NAK

W5W

H11

W5W

5

High-mounted stop light

Spoiler (Type A) (if so equipped)

Spoiler (Type B) (if so equipped)*

Rear combination light*

Turn signal

Stop/Tail/Side marker

Backup (reversing)

License plate light

16

—

W16W

—

21

21/5

16

WY21W

W21/5W

W16W

5

W5W

Always check with the Parts Department at a NISSAN dealer for the latest parts informa-

tion.

* If replacement is required it is recommended that you visit a NISSAN dealer for this

service.

Do-it-yourself 8-27

1.

Headlight assembly

2. Interior light

3.

Fog light (if so equipped)

4. Rear combination light

5.

High-mounted stop light

6. License plate light

LDI2864

8-28 Do-it-yourself

Indicates bulb removal

Indicates bulb installation

LDI2044

Interior light

Use a cloth to protect the housing.

SDI1805

Replacement procedures

All other lights are either type A, B, C or D.

When replacing a bulb, first remove the

lens, lamp and/or cover.

Do-it-yourself 8-29

2

Carefully remove the gasket protector.

᭺

3

Pull rear combination light toward the

rear of the vehicle and disconnect the

rear combination light connector to re-

move the assembly.

᭺

Remove bulbs by turning counterclock-

wise and replace with new bulbs.

LDI2374

LDI2071

Rear combination light

To replace the bulbs in the rear combina-

tion light:

High-mounted stop light (Type A)

(if so equipped):

To replace the high-mounted stop light

bulb

1

Remove the rear combination light

mounting bolts.

᭺

1. Disconnect the negative (-) battery

cable.

8-30 Do-it-yourself

2. Remove the lens cover of the high-

mounted stop light by inserting an ap-

propriate remover tool between the

top of the lens cover (the side not

touching the glass of the rear door)

A

and the vehicle . Pull toward you.

᭺

3. After the cover is removed, disconnect

the harness connector and remove

B

the high-mounted stop light bulb

rotating it counterclockwise.

by

᭺

4. Replace with new bulb and reinstall

cover.

JVC0014X

JVM0007X

License plate light

Cargo light

To replace the luggage compartment light

bulb:

A

1. Remove the light

with a suitable tool.

᭺

B

2. Remove the cover

.

᭺

3. Replace the bulb.

Do-it-yourself 8-31

Do-it-yourself -> Lights for Your Nissan Micra 4 Door Fifth Generation (2017-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals