Get Heater, air conditioner, audio and phone systems -> Bluetooth? Hands-Free Phone System Guide for Nissan Micra 4 Door Fifth Generation (2017-2023)

CAR PHONE OR CB RADIO

BLUETOOTH® HANDS-FREE PHONE

SYSTEM

When installing a CB, ham radio or car

phone in your vehicle, be sure to observe

the following precautions; otherwise, the

new equipment may adversely affect the

engine control system and other electronic

parts.

CAUTION

WARNING

∙ Keep the antenna as far away as pos-

sible from the electronic control

modules.

∙ Use a phone after stopping your ve-

hicle in a safe location. If you have to

use a phone while driving, exercise ex-

treme caution at all times so full at-

tention may be given to vehicle

operation.

∙ Keep the antenna wire more than

20 cm (8 in) away from the electronic

control system harnesses. Do not

route the antenna wire next to any

harness.

WARNING

∙ If you are unable to devote full atten-

tion to vehicle operation while talking

on the phone, pull off the road to a

safe location and stop your vehicle.

∙ A cellular phone should not be used

for any purpose while driving so full

attention may be given to vehicle op-

eration. Some jurisdictions prohibit

the use of cellular phones while

driving.

∙ Adjust the antenna standing-wave

ratio as recommended by the

manufacturer.

CAUTION

∙ Connect the ground wire from the CB

radio chassis to the body.

To avoid discharging the vehicle bat-

tery, use a phone after starting the

engine.

∙ If you are unable to devote full atten-

tion to vehicle operation while talking

on the phone, pull off the road to a

safe location and stop your vehicle.

∙ For additional information, it is rec-

ommended that you visit a NISSAN

dealer.

Heater, air conditioner, audio and phone systems 4-51

with the in-vehicle phone module when

the ignition switch is placed in the ACC or

ON position with the previously connected

cellular phone turned on and carried in the

vehicle.

NOTE:

Some devices require the user to accept

connections to other Bluetooth® de-

vices. If your phone does not connect au-

tomatic ally to the system, consult the

phone’s owner’s manual for details on

device operation.

You can connect up to six different

Bluetooth® cellular phones to the in-

vehicle phone module. However, you can

talk on only one cellular phone at a time.

Before using the Bluetooth® Hands-Free

Phone System, refer to the following notes.

∙

Set up the wireless connection be-

tween a compatible cellular phone and

the in-vehicle phone module before us-

ing the hands-free phone system.

LHA4967

Your NISSAN is equipped with the

Bluetooth® Hands-Free Phone System. If

you have a compatible Bluetooth® enabled

cellular phone, you can set up the wireless

connection between your cellular phone

and the in-vehicle phone module. With

Bluetooth® wireless technology, you can

make or receive a hands-free telephone

call with your cellular phone in the vehicle.

Once your cellular phone is connected to

the in-vehicle phone module, no other

phone connecting procedure is required.

Your phone is automatically connected

4-52 Heater, air conditioner, audio and phone systems

∙

Some Bluetooth® enabled cellular

phones may not be recognized or work

∙

While a cellular phone is connected

through the Bluetooth® wireless con-

nection, the battery power of the cellu-

lar phone may discharge quicker than

usual. The Bluetooth® Hands-Free

Phone System cannot charge cellular

phones.

– NOTE: This device complies with part 15

of the FCC Rules. Operation is subject to

the following two conditions:

properly.

Please

visit

or

www.nissanusa.com/bluetooth

1. This device may not cause interference

and

www.nissan.ca/bluetooth for a recom-

mended phone list and connecting in-

structions.

2. This device must accept any interfer-

ence received, including interference

that may cause undesired operation.

∙

Some cellular phones or other devices

may cause interference or a buzzing

noise to come from the audio system

speakers. Storing the device in a differ-

ent location may reduce or eliminate

the noise.

You will not be able to use a hands-free

phone under the following conditions:

– WARNING: This equipment complies with

FCC radiation exposure limits set forth

for an uncontrolled environment and

meets the FCC radio frequency (RF) Ex-

posure Guidelines. This equipment has

very low levels of RF energy that is

deemed to comply without maximum

permissive exposure evaluation (MPE).

But it is desirable that it should be in-

stalled and operated keeping the radia-

tor at least 20cm or more away from

person’s body.

– Your vehicle is outside of the cellular

service area.

– Your vehicle is in an area where it is

difficult to receive a cellular signal;

such as in a tunnel, in an under-

ground parking garage, near a tall

building or in a mountainous area.

For additional information, refer to the

cellular phone owner’s manual regard-

ing the telephone charges, cellular

phone antenna and body, etc.

REGULATORY INFORMATION

FCC Regulatory information

– Your cellular phone is locked to pre-

vent it from being dialed.

∙

When the radio wave condition is not

ideal or ambient sound is too loud, it

may be difficult to hear the other per-

son’s voice during a call.

– CAUTION: Changes or modifications not

expressly approved by the party respon-

sible for compliance could void the user’s

authority to operate the equipment.

This transmitter must not be co-located

or operated in conjunction with any

other antenna or transmitter.

IC Regulatory information

– NOTE: This device complies with Industry

Canada’s license-exempt RSSs. Opera-

tion is subject to the following two con-

ditions:

Do not place the cellular phone in an

area surrounded by metal or far away

from the in-vehicle phone module to

prevent tone quality degradation and

wireless connection disruption.

1. This device may not cause interference;

and

Heater, air conditioner, audio and phone systems 4-53

2. This device must accept any interfer-

ence, including interference that may

cause undesired operation of the de-

vice.

– ATTENTION: Cet équipement est con-

forme aux limites d’exposition aux rayon-

nements énoncées pour un environne-

ment non contrôlé et respecte les règles

d’exposition aux fréquences radioélec-

triques (RF) CNR-102 de l’IC. Cet équipe-

ment émet une énergie RF très faible qui

est considérée comme conforme sans

évaluation de l’exposition maximale au-

torisée (MPE).

Cependant, il est souhaitable qu’il devrait

être installé et utilisé en gardant une dis-

tance de 20 cm ou plus entre le radiateur

et le corps humain.

Initialization

When the ignition switch is placed in the ON

position, NISSANVoice Recognition is initial-

ized, which takes a few seconds. If the

button is pressed before the initialization

completes, the system will announce

“There is no phone connected” and will not

react to voice commands.

– REMARQUE: Le présent appareil est con-

forme aux CNR d’Industrie Canada appli-

cables aux appareils radio exempts de

licence. L’exploitation est autorisée aux

deux conditions suivantes:

Operating tips

1. l’appareil ne doit pas produire de brouil-

lage;

To get the best performance out of the

NISSAN Voice Recognition System, observe

the following:

2. l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi,

même si le brouillage est susceptible

d’en compromettre le fonctionnement.

∙

Keep the interior of the vehicle as quiet

as possible. Keep all vents pointed away

from the microphone and close the

windows to eliminate surrounding

noises (traffic noises, vibration sounds,

etc.), which may prevent the system

from recognizing voice commands cor-

rectly.

BLUETOOTH® is a

trademark owned

by Bluetooth SIG,

Inc. and licensed

to Panasonic.

– WARNING: This equipment complies with

IC radiation exposure limits set forth for

an uncontrolled environment and meets

RSS-102 of the IC radio frequency (RF)

Exposure rules. This equipment has very

low levels of RF energy that is deemed to

comply without maximum permissive

exposure evaluation (MPE).

But it is desirable that it should be in-

stalled and operated keeping the radia-

tor at least 20cm or more away from

person’s body.

USING THE SYSTEM

∙

Wait until the tone sounds before

speaking a command. Otherwise, the

command will not be received properly.

The system allows hands-free operation of

the Bluetooth® Hands-Free Phone System.

If the vehicle is in motion, some commands

may not be available so full attention may

be given to vehicle operation.

∙

Start speaking

a

command within

5 seconds after the tone sounds.

Speak in a natural voice without paus-

ing between words.

4-54 Heater, air conditioner, audio and phone systems

∙

For calling contacts by name, please

say both the first and last name of the

contact for better recognition.

∙

You can cancel a command when the

system is waiting for a response by say-

ing, “Cancel” or “Quit.” The system an-

nounces “Exit” and ends the Voice Rec-

ognition session. You can also press

Giving voice commands

To operate NISSAN Voice Recognition,

press the

steering wheel for less than 1.5 seconds.

After the tone sounds, speak a command.

The command given is picked up by the

microphone, and voice feedback is given

when the command is accepted.

and hold the

button on the steer-

ing wheel for 1.5 seconds at any time to

end the Voice Recognition session.

Whenever the Voice Recognition ses-

sion is canceled, a double beep is

played to indicate you have exited the

system.

button located on the

∙

If you want to adjust the volume of the

voice feedback, push the (+ or -) volume

control switches on the steering wheel

while being provided with feedback. You

can also use the radio volume control

knob.

∙

If a command is not recognized, the

system announces, “Please say or se-

lect a command from the displayed list.”

Make sure the command is said exactly

as prompted by the system and repeat

the command in a clear voice.

LHA4723

INDICATORS

When

a

cellular phone is connected

through the Bluetooth® wireless connec-

1

tion, indicators

messaging are displayed on the top of the

screen.

for the phone and text

᭺

Voice Prompt Interrupt

In most cases you can interrupt the voice

∙

If you want to go back to the previous

command, you can say “Go back” or

“Correction” any time the system is

waiting for a response.

feedback to speak the next command by

pressing the

wheel. After interrupting the system, wait

for a beep before speaking your command.

button on the steering

Heater, air conditioner, audio and phone systems 4-55

You can use the

button to

Indicator

Description

Indicates there are un-

read received

interrupt the system feedback

and give a command at once.

messages.

Indicates the

If an iPhone® is connected, Siri®

can be accessed by pressing

Bluetooth® device that

is currently connected.

Indicates the strength

of the signal the

the

button for more than

two seconds. For additional

information, refer to “Siri® Eyes

Free” in this section.

Bluetooth® device is

receiving.

Indicates the amount of

remaining Bluetooth®

device battery.

PHONE BUTTON

To answer an incoming call or to

LHA4747

end a call press the

button.

CONTROL BUTTONS

The control buttons for the Bluetooth®

Hands-Free Phone System are located on

the steering wheel.

To reject a call press and hold

the button.

VOICE COMMAND BUTTON

Press and hold the

button for

less than 1.5 seconds to initiate

the Voice Recognition session. To

exit the Voice Recognition session

press and hold the

for more

than 1.5 seconds. For additional

information, refer to “Voice prompt

interrupt” in this section.

4-56 Heater, air conditioner, audio and phone systems

3. In the Bluetooth tab, touch the “Add

New” key to connect a phone.

CONNECTING PROCEDURE

NOTE:

4. When a compatible phone is found a

message with a PIN appears on the

screen.

The connecting procedure must be per-

formed when the vehicle is stationary. If

the vehicle starts moving during the pro-

cedure, the procedure will be canceled.

5. Verify the PIN is correct and accept the

connection.

To connect a phone to the Bluetooth®

Hands-Free Phone System:

6. To access the Bluetooth® settings

menu touch the “

” key on the Con-

Manual Connecting Procedure

nections screen. The following options

are available:

1. Press the

control panel.

MENU button on the

LHA4726

2. Touch the “Connections” key on the

screen.

Menu Item

Result

Bluetooth

Allows user to switch Bluetooth® on and off. Bluetooth® must be turned on in order to connect a device.

Turns Bluetooth® functionality on. To turn off, touch the “ON” key again. The indicator light will go off.

Allows user to toggle “Phone” and “Audio” favorite settings on and off.

ON

Favorite (Connection first)

Allows user to customize the PIN to a four digit number.

Heater, air conditioner, audio and phone systems 4-57

NOTE:

tion, refer to “Bluetooth® connections

screen” in this section.

∙

Call <name> Main

Call <name> Other

Settings

Some cellular phones may require you to

accept certain permissions in order to

enable features on your Bluetooth® sys-

tem. During the Bluetooth® pairing pro-

cess, please check your cellular phone’s

display for a pop-up with the request to

grant phonebook access.

Granting phonebook access permission

will allow your contacts to be down-

loaded to the vehicle’s Bluetooth® sys-

tem. A pop-up may display on your cellu-

lar phone stating that the Bluetooth®

system would like to access your con-

tacts and call history. Please select “Al-

low” or Yes” to grant this permission.

VOICE COMMANDS

Voice commands can be used to operate

the Bluetooth® Hands-Free Phone System.

“Call <name>”

Press and hold the

button for less

Speak this command to make a call to a

contact that is stored in the phonebook.

Say “Call” followed by a phonebook name to

initiate a call. If the system does not recog-

nize the name it will display a list of similar

names. After the prompt, speak or touch

an item number from the displayed list to

place the call.

than 1.5 seconds to bring up the phone

command menu. The commands avail-

able are:

∙

Call <name>

Dial <number>

Recent Calls

“Dial <number>”

Read/Send Text (if so equipped)

Siri® (if so equipped)

Voice Assistant (if so equipped)

Phonebook

Speak this command to make a call with a

spoken phone number. After the prompt,

say “Dial” followed by a 7 to 10 digit phone

number. The system will repeat the num-

ber back. Say “Dial” to initiate the call or

“Correction” to re-enter the phone number.

Automatic Connecting Procedure

If no phone is connected to the system,

press and hold the

button on the

Quick Dial

steering wheel for less than 1.5 seconds.

After the prompt, speak “Add Phone”, the

system will announce “transferring to the

add phone settings menu”. The system will

start the pairing procedure. When a com-

patible phone is found, a message with a

PIN appears on the screen. Operate the

Bluetooth® phone to complete the con-

nection process. For additional informa-

Redial

Select Phone

Add Phone

Call <name> Mobile

Call <name> Home

Call <name> Office

4-58 Heater, air conditioner, audio and phone systems

∙

Missed Calls

The following commands are available:

“Recent Calls”

The following commands are available un-

der “Recent Calls”:

Speak this command to list the last 20

missed calls to the vehicle. If the call is

from an entry in the phonebook, the

name will be displayed. Otherwise, the

phone number of the missed call will be

displayed.

∙

<Say a Contact Name> Main

<Say a Contact Name> Home

<Say a Contact Name> Mobile

<Say a Contact Name> Office

<Say a Contact Name> Other

∙

Incoming Calls

Speak this command to list the last

20 incoming calls to the vehicle. If the

call is from an entry in the phonebook,

the name will be displayed. Otherwise,

the phone number of the incoming call

will be displayed.

When prompted, speak or touch the

item number on the screen to place the

call. Select the “Next” key to move

through the list of missed calls.

For additional information on manually se-

lecting phonebook entries, refer to “Making

a call” in this section.

“Read Text/Send Text” (if so

equipped)

Speak this command to access text mes-

saging functions. For additional informa-

tion, refer to “Text messaging” in this sec-

tion.

When prompted, speak or touch the

item number on the screen to place the

call. Select the “Next” key to move

through the list of incoming calls.

“Quick dial”

Speak this command to access the Quick

dial menu. After the prompt, speak or se-

lect an item number on the displayed list to

place the call. For additional information,

refer to “Making a call” in this section.

∙

Outgoing Calls

Speak this command to list the last 20

outgoing calls from the vehicle. If the

call was to an entry in the phonebook,

the name will be displayed. Otherwise,

the phone number of the outgoing call

will be displayed.

“Phonebook through voice

command”

Speak “Phonebook” to view a list of quick

steps to access entries stored in the

phonebook. Commands are organized by

the phone number type selected in the cel-

lular device. For additional information, re-

fer to the cellular phone’s owner’s manual.

“Redial”

Speak this command to call the last num-

ber dialed. After the prompt, say “Redial” to

dial the number of the last outgoing call.

The system will display “Redialing

<name/number>”. The name of the

phonebook entry will be displayed if it is

available, otherwise the number being re-

dialed will be displayed.

When prompted, speak or touch the

item number on the screen to place the

call. Select the “Next” key to move

through the list of outgoing calls.

Heater, air conditioner, audio and phone systems 4-59

∙

Best Match List

“Select Phone”

When the system doesn’t recognize a

phonebook name or dial number, it will

provide a list of similar sounding results.

To turn this off, touch the “ON” key, the

indicator light will turn off. To turn on,

touch the “ON” key again, the indicator

light will turn on.

Speak this command to access the Con-

nections menu. For additional information,

refer to “Bluetooth® connections screen” in

this section.

“Add Phone”

Speak this command to access the Con-

nections menu. For additional information,

refer to “Bluetooth® connections screen” in

this section.

“Settings”

LHA4705

Speak this command to access the Sys-

tem Voice settings menu. The system will

exit Voice Recognition mode. Touch one of

the following options on the screen to

change the settings.

PHONE DISPLAY SCREEN

The Phone screen can be displayed by

pressing the

panel.

button on the control

∙

Beep Only for Opening Prompt

The following options are displayed:

By touching the “ON” key, the indicator

light will illuminate, the system voice will

turn off and only a tone will sound when

the Bluetooth® Hands-Free Phone Sys-

tem is activated. To turn the system

voice back on, touch the “ON” key again,

the indicator light will turn off.

∙

Quick Dial

Displays the Quick Dial screen. For addi-

tional information, refer to “Quick dial” in

this section.

∙

Phonebook

Displays the Phonebook screen. For ad-

ditional information, refer to “Making a

call” in this section.

4-60 Heater, air conditioner, audio and phone systems

∙

Call History

For additional options to make a call, refer

to “Voice commands” in this section.

MAKING A CALL

Displays the Call History screen. For ad-

ditional information, refer to “Making a

call” in this section.

To make a call press the

button on

the control panel. Touch an option from

menu screen:

Quick Dial

Quick Dial entries can be used to quickly

make a call. The system allows up to 20

entries to be stored. To set up a quick dial

Dial Number

∙

Phonebook

Displays the Dial Number screen. For

additional information, refer to “Making

a call” in this section.

Select a person and the phone number

you wish to call from the phonebook.

Depending on the device, the phone-

book will be downloaded from the cel-

lular phone automatically when it is

connected. If the automatic download

does not take place, the phone number

must be transferred to the hands-free

phone system from the cellular phone

prior to using this method. For addi-

tional information, refer to “Phone and

text message settings” in this section.

press the

button on the control

panel. Touch the “Quick Dial” key to display a

list of quick dial entries. Touch the “Edit” key

to edit current entries or touch the “Add

New” key to make a new entry. Two meth-

ods are given to create a quick dial entry:

Text Message

Displays the received message screen.

For additional information, refer to “Text

messaging” in this section.

Connections

∙

Touch the “Copy from Call History” key

to save a phone number from the In-

coming, Outgoing or Missed call history

lists. Select the person or phone num-

ber from the menu to be added. A reg-

istration menu will display the Entry #,

phone number, phone number type

stored in the cellular phone and Voice

Tag. Select the “OK” key.

Displays the Connections screen. For

additional

information,

refer

to

“Bluetooth® connections screen” in this

section.

∙

Volume

∙

Call History

Displays the volume adjustment

screen. For additional information, refer

to “Volume & beeps” in this section.

Select a phonebook name or phone

number from the recent incoming, out-

going or missed calls tabs. Touch a

phonebook name or phone number

listed to initiate the call.

Dial Number

Enter the phone number manually us-

ing the keypad displayed on the screen.

Press the “OK” key on the screen to initi-

ate the call.

Heater, air conditioner, audio and phone systems 4-61

∙

Touch the “Copy from Phonebook” key to

save a number from the phonebook. Use

the scroll keys on the side to move up

and down through the menu. Select a

person to be added. A menu will display

the Entry #, phone number, phone num-

ber type stored in the cellular phone and

Voice Tag. Select the “OK” key.

∙

Dial Number

RECEIVING A CALL

Touch this key to dial digits during the

phone call.

When a call is received by the phone con-

nected to the vehicle’s Bluetooth® Hands-

Free Phone System, the call information is

displayed on the control panel display.

Use Handset

Touch this key to transfer the call to the

handset. To transfer the call back from

the handset to the Bluetooth® Hands-

Press the

wheel or touch the “

the screen to accept the call. To reject the

button on the steering

Answer” key on

Free Phone System, press the

button on the control panel then select

the “Transfer Hands-free” key on the

screen.

Voice tag

call touch the “

screen.

Decline” key on the

A voice tag can be recorded for each of the

registered Quick Dial numbers and can be

used to dial the number by speaking it. On

the Quick Dial registration screen, touch

the “Voice Tag” key. Select a relationship

from the list or create a new voice tag. To

record a new voice tag touch the “Custom-

ize” key on the screen then touch the “Store”

key. Speak a name after the prompt, the

new tag will be stored. To edit or create a

new voice tag select the “Customize” key

again. Touch the “Play” key to play the re-

corded voice tag, touch the “Restore” key to

edit the voice tag or “Delete” to delete the

current voice tag.

If the user is not able to answer the call

right away, touch the “Hold Call” key dis-

played on the screen. A message will be

played for the caller: “I’m not able to take a

call right now.” The user may then accept

the call when available or reject the call.

∙

Switch Call

This option will only be available when a

second call is active.

If supported by the phone, the

Bluetooth® Hands-Free Phone System

allows for call waiting functionality. If a

call is received while another call is al-

ready active, a message will be dis-

played on the screen. Press the

button on the steering wheel or touch

To reject a call, press and hold the

button on the steering wheel.

DURING A CALL

While a call is active the following options

will appear on the control panel display:

the “

cept the incoming call. Touch the

Decline” key on the screen to re-

ject the second call.

Answer” key on screen to ac-

∙

Mute

“

Touch this key to mute or unmute the

system.

4-62 Heater, air conditioner, audio and phone systems

NOTE:

While a call is active, press the

button

∙ Laws in some jurisdictions may re-

strict the use of some of the applica-

tions and features, such as social net-

working and texting. Check local

regulations for any requirements.

on the steering wheel to access additional

options. Speak one of the following com-

mands:

Many phones may require special per-

mission to enable text messaging. Check

the phone’s screen during Bluetooth®

pairing. For some phones, you may need

to enable ‘Notifications’ in the phone’s

Bluetooth® menu for text messages to

appear on the head unit. For additional

information, refer to your phone’s own-

er’s manual. Text message integration

requires that the phone support MAP

(Message Access Profile) for both receiv-

ing and sending text messages. Some

phones may not support all text mes-

saging features. Please refer to

∙

“Send Digits”

∙ Use the text messaging feature after

stopping your vehicle in a safe loca-

tion. If you have to use the feature

while driving, exercise extreme cau-

tion at all times so full attention may

be given to vehicle operation.

Speak this command followed by the

digits to enter digits during the phone

call.

∙

“Switch call”

Speak this command to hold the sec-

ond call and switch back to the original

call.

∙ If you are unable to devote full atten-

tion to vehicle operation while using

the text messaging feature, pull off

the road to a safe location and stop

your vehicle.

ENDING A CALL

www.nissanusa.com/bluetooth

or

To end an active call, press the

button

www.nissan.ca/bluetooth for compat-

ibility information, as well as your de-

vice’s owner’s manual.

on the steering wheel or touch the

“

Hang up” key on the screen.

NOTE:

The system allows for the sending and re-

ceiving of text messages through the ve-

hicle interface.

TEXT MESSAGING (if so equipped)

This feature is automatically disabled if

the connected device does not support

the Message Access Profile (MAP). For

additional information, refer to the

phone’s owner’s manual for details and

instructions.

WARNING

The availability of the text message func-

tion may vary depending on the cellular

phone.

∙ Laws in some jurisdictions may re-

strict the use of “Text-to-Speech”.

Check local regulations before using

this feature.

Heater, air conditioner, audio and phone systems 4-63

When the cellular phone connected to the

vehicle receives a text message, a notifica-

tion will appear on the control panel dis-

play. To check the message, touch the

“Read” key. Touch the “Ignore” key to save

the message to be checked later.

Access text messaging through the ve-

hicles Bluetooth® Hands-Free Phone or

through the vehicles control panel.

∙ Outgoing Calls

∙ Missed Calls

∙ Dial

Reading a received text message

1. Press and hold the

steering wheel for less than 1.5 sec-

onds.

button on the

4. Once a recipient is chosen, the system

prompts for which message to send.

Nine predefined messages are avail-

able. To choose one of the predefined

messages, speak one of the following

after the tone:

2. Say “Read Text” after the tone.

The display will show a list of 20 messages

with the sender and delivery time. Touch

the “Next” key on the screen to view all mes-

sages. To view a text message press

Text messaging using Bluetooth®

Hands-Free Phone System (if so

equipped)

the

button on the steering wheel and

∙ “Driving, can’t text”

∙ “Call me”

speak the number item list on the screen.

The following options will be available:

Sending a text message (if so equipped)

∙

Play

∙ “On my way”

∙ “Running late”

∙ “Okay”

Speak this command to have the sys-

tem say the message.

1. Press and hold the

button on the

steering wheel for less than 1.5 sec-

onds.

Reply

Speak this command to send a text

message response to the sender of the

text message.

∙ “Yes”

2. Say “Send Text” after the tone.

∙ “No”

3. The system will provide a list of avail-

able commands in order to determine

the recipient of the text message.

Choose from the following:

∙ “Where are you?”

∙ “When?”

∙

Call

Speak this command to call the sender.

∙ Quick Dial

Speak this command to move to the

previous text message (if available).

∙ Incoming Calls

∙

next text message (if available).

4-64 Heater, air conditioner, audio and phone systems

Siri® Eyes Free (if so equipped)

Received message screen

Sending a text message (if so equipped)

If a connected phone is equipped with Siri®,

it can also be used to create custom mes-

sages that are sent through the phone. For

additional information, refer to “Siri® Eyes

Free” in this section.

Touching the “Read” key on the incoming

message notification screen or selecting a

message from the message list will show

the details of the received message on the

display.

This function may not be supported de-

pending on the cellular phone.

1. Press the

panel.

button on the control

2. Touch the “Text Message” key on the

screen.

Available actions:

NOTE:

∙

Prev.

Text messages are only displayed if the

vehicle speed is less than

(8 km/h).

3. Touch the “Create Message” key on the

screen.

Touch this key to read the previous

message.

5

mph

Touch this key to read the next mes-

sage.

For Apple iPhones®, text messages can

only be sent through Siri.

Play/Stop

Touch the “Play” key to have the hands-

free phone system read out the re-

ceived message. Touch the “Stop” key to

stop reading.

Text messaging using the control

panel

Display received message list

∙

Call

1. Press the

panel.

button on the control

If the sender of the message is regis-

tered in the phonebook, touch the “Call”

key to make a call to the sender.

2. Touch the “Text Message” key on the

screen

Reply

A reply message can be selected from

the predefined list.

3. Touch an item on the list to read or

reply to the message.

Up to 100 messages can be stored in the

message list.

Heater, air conditioner, audio and phone systems 4-65

The following items are available:

Available item

Action

To

Enter Number by Keypad

Quick Dial

Phonebook

Call History

Enter the phone number of the recipient using the keypad. Touch the “OK” key to confirm.

Select a recipient from the quick dial list.

Select a recipient from the phonebook.

Select a recipient/phone number from call history.

Touch to display a list of predefined text messages.

Touch to send the message.

Select Text

Send

Fixed

4-66 Heater, air conditioner, audio and phone systems

Access the Connections screen to change

settings and view Bluetooth® information.

To access the Connections screen press

Bluetooth tab

This tab will display up to six Bluetooth®

devices. If six devices are already con-

nected, one of the devices must be deleted

before another device can be connected.

the

MENU button on the control

panel. Touch the “Connections” key on the

screen then select the Bluetooth tab.

The paired phone will be added to the list

on the Bluetooth® connections screen.

“Add New” key

Touch the this key on the screen to con-

nect a new Bluetooth® device. For addi-

tional information, refer to “Connecting

procedure” in this section.,

Touching the name of another device on

the list will switch the connected device.

“

” (back) key

Touch the “

” key to go back to the

“

” (Bluetooth® settings) key

previous screen.

LHA4716

Touch the “

play a list of options.

” key on the screen to dis-

BLUETOOTH® CONNECTIONS

SCREEN

Connecting Bluetooth®

For additional information on connecting a

cellular phone or device to the Bluetooth®

Hands-Free Phone System, refer to “Con-

necting procedure” in this section.

∙

Bluetooth

Touch this key to turn the Bluetooth®

connection on or off

1.

“

” (back) key

2. Bluetooth tab

3.

Connections screen

Favorite (Connection first)

4. “Add New” key

NOTE:

Touch this key to change which device

will be connected first when multiple

devices are connected to the vehicle.

5.

6.

7.

“

” (settings) key

” (info) key

” (Bluetooth® Audio connec-

Some cellular phones or other devices

may cause interference or a buzzing

noise to come from the audio system

speakers. Storing the device in a differ-

ent location may reduce or eliminate the

noise.

Turn the “

” key on or off to make the

tion) key

device a favorite connection.

8.

“

” (Bluetooth® Hands-Free

Turn the “

” key on or off to make the

Phone System connection) key

device a favorite connection.

Heater, air conditioner, audio and phone systems 4-67

∙

“

” (Bluetooth® Audio

Touch this key to customize the PIN

code. Input a four digit number then

touch the “OK” key. The new PIN will be

set.

connection) key

A list of connected devices will be displayed

on the screen. Touch the “

the name to connect

Bluetooth® Audio. If the device is listed as a

favorite, a star will appear on the icon. Se-

lect the key again to disconnect the device.

The device will not be removed from the

list. For additional information on removing

” key next to

a

device to

“

” (info) key

Touch the “

” key on the screen to dis-

play the information of the cellular phone

or to delete the device.

Touch the “Delete” key to remove a paired

device then select “Yes” when a message

appears.

a device, refer to “

section.

(info) key” in this

LHA4721

“

” (Bluetooth® Hands-Free

PHONE AND TEXT MESSAGE

SETTINGS

Phone System connection) key

A list of connected devices will be displayed

on the screen. Touch the “

Bluetooth® Hands-Free Phone System set-

tings can be changed according to the us-

er’s preference. To access the “Phone” set-

MENU button

on the control panel. Touch the “Settings”

key then select the “Phone” key.

” key next to

the name to connect a device to the

Hands-Free Phone System. If the phone is

listed as a favorite, a star will appear on the

icon. Select the key again to disconnect the

device. The device will not be removed

from the list. For additional information on

tings menu press the

removing a device, refer to “

in this section.

(info) key”

4-68 Heater, air conditioner, audio and phone systems

The following options are available:

Menu Item

Result

Quick Dial

Edit

Delete All

Entries in the Quick Dial can be edited. For additional information, refer to “Quick dial” in this section.

Deletes all of the stored phone numbers in quick dial.

Phonebook

Download Entire Phone- All of the phone numbers that are stored in a phonebook of a cellular phone that is connected to the vehicle

book

are downloaded at once. For additional information, refer to the cellular phone’s owner’s manual.

Turns on/off automatic downloading of the phonebook from the connected cellular phone.

Turns the text messaging function on/off.

Turn the incoming message sound on/off.

Turns the signature setting for the outgoing text message on/off.

Turns on/off the automatic text message reply function.

Auto Downloaded

Text Message

Text Message Ringtone

Signature

Text Message

Auto Reply

Auto Reply Text Message Select the text message to be used for the automatic reply. Choose from a list of predefined messages.

Notifications

Driver Only

Vehicle Ringtone

When this item is turned on, incoming call notification is displayed only on the handset.

Turns the vehicle ringtone on/off.

Automatic Hold

When this item turns on, an incoming call will be put on hold automatically.

Heater, air conditioner, audio and phone systems 4-69

Volume Settings

Volume & beeps

There are several methods to customize

the volume settings.

The Volume settings screen can be found

by pressing the

button on the control

panel then touching the “Volume” key on

the screen. To adjust the volume of the

following options, touch the “–” and “+” keys

on the screen.

Volume & Beeps

The Volume & Beeps screen can be found

by pressing the

MENU button on the

The available settings are:

control panel, touching the “Settings” key

on the screen and selecting “Volume &

Beeps”. To adjust the volume of the follow-

ing options, touch the “–” and “+” keys on the

screen.

∙

Ringtone

Adjust the volume level of the ringtone

of incoming calls.

∙

Outgoing Call

Adjust the volume level of the outgoing

calls.

The available settings are:

∙

Ringtone

Adjust the volume level of the ringtone

of incoming calls.

Outgoing Call

Adjust the volume level of the outgoing

calls.

Voice Prompt Vol.

Adjust the volume level of the system

voice.

Text-to-speech Vol.

Adjust the volume of the replay voice for

text messaging.

Button Beeps

Turns on/off the button beep sounds

and alarm for prohibited operations.

4-70 Heater, air conditioner, audio and phone systems

Heater, air conditioner, audio and phone systems -> Bluetooth? Hands-Free Phone System for Your Nissan Micra 4 Door Fifth Generation (2017-2023)

Related Topics

Popular Owner Manuals

Latest Owner Manuals