Get Instruments and controls -> Warning lights Guide for Nissan Patrol SUV Sixth Generation (2010-2023)

WARNING LIGHTS, INDICATOR

LIGHTS AND AUDIBLE REMINDERS

Anti-lock Braking System (ABS) warn-

ing light

Engine start operation indicator light*

Front fog light indicator light*

Lane departure warning light (orange)*

Low fuel warning light*

Automatic Transmission (AT) check

warning light

Automatic Transmission (AT) oil tem-

perature warning light*

Front passenger air bag status light*

High beam assist indicator light*

Low tire pressure warning light*

Low washer fluid warning light*

Automatic Transmission (AT) park

warning light

Blind Spot Warning (BSW)/Intelligent

Blind Spot Intervention system warn-

ing light (orange)*

High beam indicator light

Master warning light*

Hill descent control system ON indi-

cator light*

Brake warning light

Charge warning light

P position selecting warning light*

Seat belt warning light

Intelligent Lane Intervention ON indi-

cator light (green)*

Intelligent Distance Control system

warning light (orange)*

Speed [120 km/h (75 MPH)] warning

light*

Malfunction Indicator Light (MIL)

Rear fog light indicator light*

Security indicator light

Supplemental Restraint System (SRS)

Door open warning light*

air bag warning light

Vehicle Dynamic Control (VDC) warn-

ing light

Engine oil pressure warning light

Four-Wheel Drive (4WD) warning light

(4WD models)

Automatic Transmission (AT) position

Small light indicator light

indicator light*

Intelligent Blind Spot Intervention ON

indicator light (green)*

SNOW mode indicator light*

TOW mode indicator light*

Headlight warning light*

Intelligent Cruise Control (ICC) system

warning light (orange)*

Check suspension indicator light*

Intelligent Emergency Braking system

warning light*

Turn signal/hazard indicator lights

Cruise indicator light*

Vehicle Dynamic Control (VDC) off

indicator light

Intelligent Key system warning light*

Differential lock indicator light*

ECO mode system indicator light*

*: if equipped

2-16 Instruments and controls

CHECKING LIGHTS

(P.5-104).)

Automatic Transmission (AT) park

warning light

This light indicates that the Automatic Trans-

mission (AT) parking function is not engaged. If

the transfer control is not secured in any

driving position while the AT shift lever is in

the “P” (Park) position, the transmission will

disengage and the wheels will not lock.

For 4WD models: If the AT park warning light

illuminates with the shift lever in the “P”

(Park) position, shift the Four-Wheel Drive

(4WD) shift switch to the AUTO, 4H or 4L

position again with the shift lever in the N

(Neutral) position. (See “Four-Wheel Drive

(4WD) (4WD models)” (P.5-16).)

With all doors closed, apply the parking brake,

fasten the seat belts and place the ignition

switch in the “ON” position without starting the

engine. The following lights (if equipped) will

Except for Mexico: While the differential lock

is engaged, the ABS warning light illumi-

nates. This indicates that the anti-lock func-

tion is not fully operating. (See “Differential

lock mode switch (except for Mexico)” (P.5-22)

for the rear differential lock function.)

come on:

,

The following lights (if equipped) will come on

briefly and then go off : ,

,

Automatic Transmission (AT)

check warning light

When the ignition switch is in the “ON” position,

the Automatic Transmission (AT) check warn-

ing light illuminates and then turns off. This

indicates that the AT is operational.

If the AT check warning light illuminates while

the engine is running, or while driving, it may

indicate that the AT is not functioning properly

and may need servicing. Have the system

checked, and if necessary repaired, by a NISSAN

dealer promptly.

,

If any light does not come on or operates in a

way other than described, it may indicate a

burned-out bulb and/or a system malfunction.

Have the system checked, and if necessary

repaired, by a NISSAN dealer promptly.

Some indicators and warnings are also dis-

played on the vehicle information display

(model with color display or dot matrix display).

(See “Vehicle information display (Type A (mod-

el with color display))” (P.2-26) or “Vehicle

information display (Type B (model with dot

matrix display))” (P.2-35).)

Blind Spot Warning (BSW)/Intelli-

gent Blind Spot Intervention system

warning light (orange; if equipped)

When the ignition switch is pushed to the “ON”

position, the indicator light will first illuminate in

orange and turn green before turning off. This

indicates that the Blind Spot Warning (BSW) and

Intelligent Blind Spot Intervention systems are

operational.

If the light comes on in orange and remains on,

it may indicate that the BSW, Intelligent Blind

Spot Intervention and RCTA (if equipped) sys-

tems are not functioning properly. Although

the vehicle is still driveable, have the systems

checked by a NISSAN dealer. See “Blind Spot

Warning/Intelligent Blind Spot Intervention/In-

telligent Back-up Intervention” (P.5-32) or “Rear

Cross Traffic Alert (RCTA)” (P.5-45).

Automatic Transmission (AT) oil

WARNING LIGHTS

temperature warning light (if equipped)

Anti-lock Braking System (ABS)

warning light

When the ignition switch is in the “ON” position,

the Anti-lock Braking System (ABS) warning

light illuminates and then turns off. This in-

dicates the ABS is operational.

If the ABS warning light illuminates while the

engine is running, or while driving, it may

indicate the ABS is not functioning properly.

Have the system checked by a NISSAN dealer.

If an ABS malfunction occurs, the anti-lock

function is turned off. The brake system then

operates normally, but without anti-lock assis-

tance. (See “Anti-lock Braking System (ABS)”

This light illuminates when the Automatic

Transmission (AT) oil temperature is too high.

If the light illuminates while driving, reduce the

vehicle speed as soon as safely possible until

the light turns off.

CAUTION:

Continued vehicle operation when the AT oil

temperature warning light is on may damage

the AT.

Instruments and controls 2-17

driving, stop the vehicle safely as soon as

possible. Stop the engine and check the brake

fluid level. If the brake fluid level is at the

minimum mark, add brake fluid as necessary.

(See “Brake fluid” (P.8-13).)

When the charge warning light illuminates

while driving, stop the vehicle safely as soon

as possible. Stop the engine and check the

alternator belt. If the alternator belt is loose,

broken or missing, the charging system needs

repair. (See “Drive belt” (P.8-11).)

If the alternator belt appears to be functioning

correctly but the charge warning light remains

illuminated, have the charging system checked

by a NISSAN dealer promptly.

Brake warning light

WARNING:

.

If the brake fluid level is below the

minimum mark on the brake fluid reser-

voir, do not drive the vehicle until the

If the brake fluid level is sufficient, have the

brake system checked by

promptly.

a

NISSAN dealer

brake system has been checked by

NISSAN dealer.

a

Low hydraulic pressure warning indicator:

If the brake warning light illuminates when the

engine is running, or while driving with the

parking brake is released, check the brake fluid

level. If the brake fluid level is sufficient, it may

indicate low hydraulic pressure in the brake

booster. Have the brake system checked by a

NISSAN dealer promptly.

.

Even if you judge it to be safe, have your

vehicle towed because driving it could be

dangerous.

Depressing the brake pedal without the

engine running and/or with a low brake

fluid level could increase the stopping

distance and require greater pedal travel

distance and effort.

CAUTION:

Do not continue driving if the alternator belt

is loose, broken or missing.

Intelligent Distance Control sys-

Anti-lock Braking System (ABS) warning in-

dicator:

tem warning light (orange; if equipped)

The brake warning light indicates the parking

brake system operation, low brake fluid level/

low hydraulic pressure of the brake system and

Anti-lock Braking System (ABS) malfunction.

This light comes on if there is a malfunction in

When the parking brake is released and the

brake fluid level is sufficient, if both the brake

warning light and the Anti-lock Braking System

(ABS) warning light illuminate, it may indicate

that the ABS is not functioning properly. Have

the brake system checked, and if necessary

repaired, by a NISSAN dealer promptly. (See

“Anti-lock Braking System (ABS) warning light”

(P.2-17).)

the Intelligent Distance Control system.

If the warning light illuminates, park the vehicle

in a safe place. Turn the engine off, restart the

engine, resume driving and turn on the Intelli-

gent Distance Control system again.

If it is not possible to turn on the system or

the warning light stays on, it may indicate

that the system is malfunctioning. Although

the vehicle is still driveable under normal

conditions, have the vehicle checked at a

NISSAN dealer. See “Intelligent Distance Con-

trol system (for Mexico)” (P.5-70).

Parking brake warning indicator:

When the ignition switch is pushed to the “ON”

position with the parking brake applied, the

brake warning light illuminates. When the

parking brake is released, the brake warning

light turns off.

If the parking brake is not fully released, the

brake warning light remains on. Be sure that

the brake warning light has turned off before

driving. (See “Parking brake” (P.3-33).)

Charge warning light

When the ignition switch is in the “ON” position,

the charge warning light illuminates. After

starting the engine, the charge warning light

turns off. This indicates that the charging

system is operational.

If the charge warning light illuminates while the

engine is running, or while driving, it may

indicate that the charging system is not

functioning properly and may need servicing.

Low brake fluid warning indicator:

If the brake warning light illuminates while the

engine is running, or while driving, and the

parking brake is released, it may indicate that

the brake fluid level is low.

When the brake warning light illuminates while

2-18 Instruments and controls

Door open warning light (if equipped)

Four-Wheel Drive (4WD) warning

light (4WD models)

When the ignition switch is in the “ON” position,

the Four-Wheel Drive (4WD) warning light

illuminates. After starting the engine, the 4WD

warning light turns off.

If the 4WD system malfunctions or the revolu-

tion or radius of the front and the rear wheel

differs, the warning light will either remain

illuminated or blink. (See “Four-Wheel Drive

(4WD) (4WD models)” (P.5-16).)

Headlight warning light (if equipped)

This light illuminates if the LED headlights are

malfunctioning. Contact a NISSAN dealer.

When the ignition switch is in the “ON” position,

the door open warning light illuminates if any

of the doors and/or back door are open or not

closed securely.

Intelligent Cruise Control (ICC) sys-

tem warning light (orange; if equipped)

Engine oil pressure warning light

When the ignition switch is in the “ON” position,

the Intelligent Cruise Control (ICC) system

warning light illuminates. After starting the

engine, the ICC system warning light turns off.

This indicates that the ICC system is opera-

tional.

When the ignition switch is in the “ON” position,

the engine oil pressure warning light illumi-

nates. After starting the engine, the engine oil

pressure warning light turns off. This indicates

that the oil pressure sensors in the engine are

operational.

If the engine oil pressure warning light illumi-

nates or blinks while the engine is running, it

may indicate that the engine oil pressure is low.

CAUTION:

This light illuminates if there is a malfunction in

.

If the 4WD warning light illuminates or

blinks while driving, reduce the vehicle

speed and have your vehicle checked by

a NISSAN dealer as soon as possible.

the ICC system.

If the ICC system warning light illuminates, park

the vehicle in a safe location. Turn the engine

off, restart the engine, resume driving and set

the ICC system again.

If it is not possible to set the system or the ICC

system warning light remains on, it may

indicate that the system is malfunctioning.

Although the vehicle is still driveable under

normal conditions, have the system checked by

a NISSAN dealer.

Stop the vehicle safely as soon as possible.

Stop the engine immediately and call a NISSAN

dealer.

If the 4WD warning light turns on when

driving on dry or hard surfaced roads:

— in the 4H position, shift the 4WD shift

switch to AUTO

— in the 4L position, stop the vehicle and

shift the transmission shift lever to

the “N” (Neutral) position and shift the

4WD shift switch to AUTO

CAUTION:

.

Running the engine with the engine oil

pressure warning light illuminated could

cause serious damage to the engine.

The engine oil pressure warning light is

not designed to indicate a low oil level.

The oil level should be checked using the

dipstick. (See “Engine oil” (P.8-9).)

See “Intelligent Cruise Control (ICC) system”

(P.5-52).

If the warning light is still on after the above

operations, have your vehicle checked by a

NISSAN dealer as soon as possible.

/

Intelligent Emergency Brak-

ing system warning light (if equipped)

When the ignition switch is in the “ON” position,

the Intelligent Emergency Braking system

warning light illuminates. After starting the

engine, the Intelligent Emergency Braking sys-

tem warning light turns off.

This light illuminates when the Intelligent

Emergency Braking system is set to “OFF” on

Instruments and controls 2-19

the lower display (model with dual display) or

the center display (model with single display).

Lane departure warning light

(orange; if equipped)

When the ignition switch is pushed to the ON

position, the light will come on in orange, turn

green, and then turn off. This indicates that the

Lane Departure Warning (LDW) and Intelligent

Lane Intervention systems are operational.

While the LDW and/or Intelligent Lane Inter-

vention system is on, the light will blink in

orange and a warning chime will sound if the

vehicle is traveling close to either the left or the

right of a traveling lane with detectable lane

markers.

Low tire pressure warning light (if

equipped)

When the ignition switch is in the “ON” position,

the low tire pressure warning light illuminates

and then turns off. This indicates that the low

tire pressure warning system is operational.

If the light illuminates when the Intelligent

Emergency Braking system is “ON”, it may

indicate that the system is unavailable. See

“Intelligent Emergency Braking with pedestrian

detection system” (P.5-77) or “Intelligent Emer-

gency Braking system” (P.5-85) for more details.

This light illuminates if there is low tire pressure

or a tire pressure warning system malfunction.

Intelligent Key system warning

light (if equipped)

The Tire Pressure Monitoring System (TPMS)

monitors the tire pressure of all tires except the

spare.

After the ignition switch is placed in the “ON”

position, this light comes on for about

2

Low tire pressure warning:

seconds and then turns off.

If the vehicle is being driven with low tire

pressure, the warning light will illuminate. A

check tire pressure warning (if equipped) also

appears on the vehicle information display.

When the low tire pressure warning light

illuminates, you should stop and adjust the tire

pressure to the recommended COLD tire pres-

sure shown on the tire placard. Use a tire

pressure gauge to check the tire pressure.

The low tire pressure warning light may not

automatically turn off when the tire pressure is

adjusted. After the tire is inflated to the

recommended pressure, drive the vehicle at

speeds above 25 km/h (16 MPH) to activate the

TPMS and turn off the low tire pressure

warning light.

If the light comes on in orange and remains on,

it may indicate that the LDW and Intelligent

Lane Intervention systems are not functioning

This light illuminates or blinks as follows:

.

The light blinks in yellow when the door is

closed with the Intelligent Key left outside

the vehicle and the ignition switch in the

“ACC” or “ON” position. Make sure that the

Intelligent Key is inside the vehicle (model

with segment display).

properly. Have the systems checked by

NISSAN dealer.

a

See “Lane Departure Warning (LDW) system/

Intelligent Lane Intervention system” (P.5-25).

.

The light blinks in green when the Intelli-

gent Key battery is running out of power.

Replace the battery with a new one (model

with segment display). (See “Battery” (P.8-

18).)

The light illuminates in yellow when it

warns of a malfunction with the electrical

steering lock system or the Intelligent Key

system.

Low fuel warning light (if equipped)

The low fuel warning light illuminates when the

fuel level in the tank is getting low. Refuel as

soon as it is convenient, preferably before the

fuel gauge reaches the empty (0) position.

There will be a small reserve of fuel remain-

ing in the tank when the fuel gauge reaches

the empty (0) position.

For additional information, see “Tire Pressure

If the warning light illuminates in yellow while

the engine is stopped, it may be impossible to

free the steering lock or to start the engine. If

the light comes on while the engine is running,

you can drive the vehicle. However in these

cases, contact a NISSAN dealer for repair as

soon as possible.

Monitoring System (TPMS)” (P.5-6).

2-20 Instruments and controls

flat and all tires are properly inflated,

have the vehicle checked by a NISSAN

dealer.

TPMS malfunction:

Master warning light (if equipped)

The master warning light illuminates when a

warning message appears in the vehicle in-

formation display.

(See “Vehicle information display (Type A (mod-

el with color display))” (P.2-26) or “Vehicle

information display (Type B (model with dot

matrix display))” (P.2-35).)

If the TPMS is not functioning properly, the low

tire pressure warning light will flash for ap-

proximately 1 minute when the ignition switch

is pushed ON. The light will remain on after 1

minute. Have the system checked by a NISSAN

dealer.

The check tire pressure warning (if equipped)

does not appear if the low tire pressure

warning light illuminates to indicate a TPMS

malfunction.

.

Since the spare tire is not equipped with

the TPMS, when a spare tire is mounted

or a wheel is replaced, the TPMS will not

function and the low tire pressure warn-

ing light will flash for approximately 1

minute. The light will remain on after 1

minute. Contact your NISSAN dealer as

soon as possible for tire replacement

and/or system resetting.

P position selecting warning light

(if equipped)

The warning light blinks in red when the

ignition switch is pushed to stop the engine

with the shift lever in any position except the “P”

(Park) position.

If this warning appears, move the shift lever to

the “P” (Park) position or push the ignition

switch to the “ON” position.

An inside warning chime will also sound.

See “Intelligent Key system” (P.3-5).

For additional information, see “Tire Pressure

Replacing tires with those not originally

specified by NISSAN could affect the

proper operation of the TPMS.

Monitoring System (TPMS)” (P.5-6).

WARNING:

.

If the light does not illuminate with the

ignition switch pushed ON, have the

vehicle checked by a NISSAN dealer as

soon as possible.

CAUTION:

.

The TPMS is not a substitute for the

regular tire pressure check. Be sure to

check the tire pressure regularly.

If the light illuminates while driving, avoid

sudden steering maneuvers or abrupt

braking, reduce vehicle speed, pull off

the road to a safe location and stop the

vehicle as soon as possible. Driving with

under-inflated tires may permanently

damage the tires and increase the like-

lihood of tire failure. Serious vehicle

damage could occur and may lead to an

accident and could result in serious

personal injury. Check the tire pressure

for all four tires. Adjust the tire pressure

to the recommended COLD tire pressure

shown on the tire placard to turn the low

tire pressure warning light OFF. If the

light still illuminates while driving after

adjusting the tire pressure, a tire may be

flat or the TPMS may be malfunctioning.

If you have a flat tire, replace it with a

spare tire as soon as possible. If no tire is

If the vehicle is being driven at speeds of

less than 25 km/h (16 MPH), the TPMS

may not operate correctly.

Be sure to correctly install the specified

Seat belt warning light

size of tires to all four wheels.

Type A:

The light illuminates whenever the ignition

switch is placed in the “ON” position, and will

remain illuminated until the driver’s seat belt is

fastened.

Low washer fluid warning light (if

equipped)

The low washer fluid warning light illuminates

when the washer fluid in the reservoir is at a

low level. Add washer fluid as necessary. (See

“Window washer fluid” (P.8-17).)

For precautions on seat belt usage, see “Seat

belts” (P.1-13).

Instruments and controls 2-21

system or hill descent control system (if

equipped) is not functioning properly and may

need servicing. Have the system checked, and if

Type B:

Supplemental Restraint System

(SRS) air bag warning light

When the ignition switch is in the “ON” position,

the seat belt warning light illuminates. The light

will continue to illuminate until the driver’s and/

or the front passenger (if equipped) seat belts

are fastened.

When the vehicle speed exceeds 15 km/h (10

MPH), the light will blink and the chime will

sound unless the driver’s and/or the front

passenger (if equipped) seat belts are securely

fastened. The chime will continue to sound for

about 90 seconds until the seat belts are

fastened.

necessary repaired, by

promptly.

a NISSAN dealer

When the ignition switch is in the “ON” position,

the Supplemental Restraint System (SRS) air

If a malfunction occurs the VDC, hill start assist

function or hill descent control system (if

equipped) is turned off, but the vehicle is still

driveable.

bag warning light illuminates for about

7

seconds and then turns off. This indicates that

the SRS air bag system is operational.

If any of the following conditions occur, the SRS

air bag system and pre-tensioner seat belt

need servicing. Have the system checked, and if

See “Vehicle Dynamic Control (VDC) system”

(P.5-22) and “Hill start assist system” (P.5-25).

necessary repaired, by

a NISSAN dealer

INDICATOR LIGHTS

promptly.

For precautions on seat belt usage, see “Seat

.

The SRS air bag warning light remains

Automatic Transmission (AT) po-

sition indicator light (if equipped)

When the ignition switch is pushed to the “ON”

position, the indicator in the vehicle informa-

tion display shows the automatic shift position.

belts” (P.1-13).

illuminated after about 7 seconds.

The SRS air bag warning light flashes

Type C:

intermittently.

The light illuminates whenever the ignition

switch is placed in the “ON” position, and will

remain illuminated until the driver’s seat belt is

fastened.

The seat belt warning light for the front

passenger will illuminate if the seat belt is not

fastened when the front passenger’s seat is

occupied. For approximately 5 seconds after

the ignition switch is placed in the “ON” posi-

tion, the system does not activate the warning

light for the front passenger.

The SRS air bag warning light does not

come on at all.

Unless checked and repaired, the SRS air bag

system and pre-tensioner seat belt may not

function properly. (See “Supplemental Restraint

System (SRS)” (P.1-35).)

7-speed AT models:

In the manual shift mode, when the transmis-

sion does not shift to the selected gear due to a

transmission protection mode, the AT position

indicator light will blink and a buzzer will sound.

Vehicle Dynamic Control (VDC)

warning light

When the ignition switch is in the “ON” position,

the Vehicle Dynamic Control (VDC) warning

light illuminates and then turns off.

See “Driving with Automatic Transmission (AT)”

(P.5-12) for further details.

For precautions on seat belt usage, see “Seat

belts” (P.1-13).

Intelligent Blind Spot Intervention

ON indicator light (green; if equipped)

The warning light blinks when the VDC system

Speed [120 km/h (75 MPH)] warn-

ing light (if equipped)

This light blinks when the vehicle speed goes

over approximately 120 km/h (75 MPH). Be sure

to observe the speed limit in the area where

you are driving.

The light comes on in green when the Intelli-

gent Blind Spot Intervention system is turned

on. The light turns off when the system is

turned off.

is operating.

When the warning light blinks while driving, the

driving condition is slippery and the vehicle’s

traction limit is about to be exceeded.

If the warning light illuminates when the

ignition switch is placed in the “ON” position, it

may indicate that the VDC, hill start assist

2-22 Instruments and controls

NOTE:

Differential lock indicator light (if equipped)

When the ignition switch is in the “ON” position,

the differential lock indicator light illuminates

and then turns off.

When the differential lock mode switch is in the

“ON” position, the differential lock indicator light

will blink and then stay on after the differential

gear is completely locked.

Front passenger air bag status

light (if equipped)

This light is common with the Blind Spot

Warning (BSW) system warning light (or-

ange). (See “Blind Spot Warning (BSW)/Intel-

ligent Blind Spot Intervention system

warning light (orange; if equipped)” (P.2-17).)

For more details, see “Blind Spot Warning/

Intelligent Blind Spot Intervention/Intelligent

Back-up Intervention” (P.5-32).

The front passenger air bag status light (

)

located on the instrument panel will illuminate

and the front passenger air bag will be OFF

depending on how the front passenger seat is

being used.

For front passenger air bag status light opera-

tion, see “Supplemental front-impact air bag

system (with Advanced Air Bag System)” (P.1-42)

of this manual.

See “Differential lock mode switch (except for

Check suspension indicator light

(if equipped)

When the ignition switch is placed in the “ON”

position, the light comes on for 2 seconds.

Mexico)” (P.5-22).

ECO mode system indicator light

(if equipped)

High beam assist indicator light (if

equipped)

The high beam assist indicator light illuminates

when the headlights come on while the head-

light switch is in the “AUTO” position with the

high beam selected. This indicates that the

high beam assist system is operational. (See

“High beam assist” (P.2-44).)

The ECO mode system indicator light illumi-

Cruise indicator light (if equipped)

nates when the ECO mode system is turned on.

(See “ECO mode system” (P.5-99).)

The cruise indicator light indicates the activa-

tion of the cruise control system.

Engine start operation indicator

light (if equipped)

This light appears when the shift lever is in the

“P” (Park) position. This light means that the

engine will start by pushing the ignition switch

with the brake pedal depressed. You can start

the engine directly in any position.

Cruise main switch indicator:

When the cruise control main switch is turned

on, the indicator light will illuminate, indicating

the cruise control system is in the standby

mode. (See “Cruise control” (P.5-50).)

High beam indicator light

The high beam indicator light illuminates when

the headlight high beam is on. The indicator

turns off when the low beam is selected. (See

“Headlight and turn signal switch” (P.2-43).)

Cruise malfunction:

If the cruise indicator light blinks while the

engine is running, it may indicate the cruise

control system is not functioning properly.

Have the system checked by a NISSAN dealer.

(See “Cruise control” (P.5-50).)

Front fog light indicator light (if equipped)

The front fog light indicator light illuminates

when the front fog lights are on. (See “Fog light

switch” (P.2-47).)

Hill descent control system ON

indicator light (if equipped)

When the ignition switch is in the “ON” position

the hill descent control system on indicator

light illuminates briefly and then turns off. This

indicates that the hill descent control system is

operational.

The light illuminates when the hill descent

Instruments and controls 2-23

control system is activated.

.

Incorrect setting of the engine control

system may lead to non-compliance of

local and national emission laws and

regulations.

If the MIL blinks while the engine is running, it

may indicate a potential malfunction in the

emission control system. In this case, the

emission control system may not function

properly and may need servicing. Have the

system checked, and if necessary repaired, by a

NISSAN dealer promptly.

If the hill descent control switch is on and the

indicator light blinks, the system is not en-

gaged.

If the indicator light does not illuminate or blink

when the hill descent control switch is on, the

system may not be functioning properly. Have

the system checked by a NISSAN dealer.

When the ignition switch is in the “ON” position,

the Malfunction Indicator Light (MIL) illumi-

nates. After starting the engine, the MIL turns

off. This indicates that the engine control

system is operational.

Precautions:

To reduce or avoid possible damage to the

For additional information, see “Hill descent

engine control system when the MIL blinks:

control system (except for Mexico)” (P.5-24).

Except for Mexico:

.

Avoid driving at speeds above 70 km/h (43

MPH).

If the MIL illuminates while the engine is

running, it may indicate that the engine control

system is not functioning properly and may

need servicing. Have the vehicle checked, and if

Intelligent Lane Intervention ON

indicator light (green; if equipped)

The light comes on in green when the Intelli-

gent Lane Intervention system is turned on.

The light turns off when the system is turned

off.

.

Avoid sudden acceleration or deceleration.

Avoid going up steep uphill grades.

necessary repaired, by

a NISSAN dealer

Avoid carrying or towing unnecessary

promptly.

loads.

If the MIL blinks while the engine is running, it

may indicate a potential malfunction in the

emission control system. In this case, the

emission control system may not function

properly and may need servicing. Have the

system checked, and if necessary repaired, by a

NISSAN dealer promptly.

Rear fog light indicator light (if equipped)

The rear fog light indicator light illuminates

when the rear fog light turns on. (See “Fog light

switch” (P.2-47).)

NOTE:

This light is common with the lane departure

warning light (orange). (See “Lane departure

warning light (orange; if equipped)” (P.2-20).)

For more details, see “Lane Departure Warning

(LDW) system/Intelligent Lane Intervention sys-

tem” (P.5-25).

For Mexico:

Security indicator light

When the ignition switch is in the “ON” position,

sometimes the MIL may illuminate for 20

seconds and then blink for 10 seconds, without

the engine running. This is due to a function of

checking the engine control system, and it is

not a malfunction. After a few normal drives,

this function will not occur and the MIL stays

illuminated with the ignition switch in the “ON”

position.

The security indicator light blinks when the

ignition switch is in the “ACC”, “OFF” or “LOCK”

position. This function indicates that the secur-

ity system equipped on the vehicle is opera-

tional.

If the security system is malfunctioning, this

light will remain on while the ignition switch is

in the “ON” position. (See “Security system” (P.3-

15) for additional information.)

Malfunction Indicator Light (MIL)

CAUTION:

.

Continuing vehicle operation without

proper servicing of the engine control

system could lead to poor driveability,

reduced fuel economy, and damage to

the engine control system, which may

affect the vehicle’s warranty coverage.

If the MIL illuminates while the engine is

running, it may indicate that the engine control

system is not functioning properly and may

need servicing. Have the vehicle checked, and if

necessary repaired, by

promptly.

a NISSAN dealer

2-24 Instruments and controls

with the Four-Wheel Drive (4WD) shift switch,

the VDC system is disabled and the VDC off

indicator light illuminates. (4WD models) (See

“Vehicle Dynamic Control (VDC) system” (P.5-

22).)

Except for Mexico: When the rear differential

lock is engaged with the differential lock mode

switch or the 4L position is selected with the

Four-Wheel Drive (4WD) shift switch, the VDC

system is disabled and the VDC off indicator

light illuminates. (See “Vehicle Dynamic Control

(VDC) system” (P.5-22) and “Differential lock

mode switch (except for Mexico)” (P.5-22).)

Light reminder chime

Small light indicator light

The light reminder chime will sound if the

driver’s side door is opened headlight switch

The small light indicator light illuminates when

the front clearance lights, instrument panel

lights (if equipped), rear combination lights and

license plate lights are on. The indicator light

turns off when the small light is turned off.

is in either the

or

position, and the

ignition switch is in the “ACC”, “OFF” or “LOCK”

position.

Be sure to turn the headlight switch to the

“OFF” or “AUTO” position (with the fog light

switch in the “OFF” position) when you leave the

vehicle.

Except for Mexico: The chime will also sound for

2 seconds when the ignition switch is placed in

the “OFF” position with the fog lights on while

the headlight switch is in the “AUTO” position.

SNOW mode indicator light (if equipped)

When selecting SNOW mode while the engine is

running, this light will illuminate. (See “SNOW

mode (for Mexico)” (P.5-21).)

AUDIBLE REMINDERS

TOW mode indicator light (if equipped)

This light will illuminate when the TOW mode is

selected while the engine is running. (See “TOW

mode (for Mexico)” (P.5-103).)

Brake pad wear warning

Parking brake reminder chime

The disc brake pads have audible wear warn-

ings. When a brake pad requires replacement, it

will make a high pitched scraping sound when

the vehicle is in motion. This scraping sound

will first occur only when the brake pedal is

depressed. After more wear of the brake pad,

the sound will always be heard even if the

brake pedal is not depressed. Have the brakes

checked as soon as possible if the wear

warning sound is heard.

The parking brake reminder chime will sound if

the vehicle is driven at more than 7 km/h (4

MPH) with the parking brake applied. Stop the

vehicle and release the parking brake.

Turn signal/hazard indicator lights

Seat belt warning chime (if equipped)

Type A:

The turn signal/hazard indicator lights blink

when the turn signal switch lever or hazard

indicator flasher switch is on. (See “Headlight

and turn signal switch” (P.2-43) or “Hazard

indicator flasher switch” (P.6-2).)

The chime will sound for about

6 seconds

unless the driver’s seat belt is securely fas-

tened.

Have the system checked, and if necessary

repaired, by a NISSAN dealer promptly. (See

“Brakes” (P.8-12).)

Type B:

Vehicle Dynamic Control (VDC) off

indicator light

When the ignition switch is in the “ON” position,

the Vehicle Dynamic Control (VDC) off indicator

light illuminates and then turns off.

When the vehicle speed exceeds 15 km/h (10

MPH), the chime will sound unless the front seat

belts are securely fastened. The chime will

continue to sound for about 90 seconds until

the front seat belts are fastened.

Door lock warning chime

When the chime sounds, be sure to check both

the vehicle and the Intelligent Key. (See “Trou-

bleshooting guide” (P.3-10).)

The VDC off indicator light illuminates when the

VDC OFF switch is pushed to the “OFF” position.

When the VDC OFF switch is pushed to the

“OFF” position, the VDC system is turned off.

For Mexico: When the 4L position is selected

Instruments and controls 2-25

VEHICLE INFORMATION DISPLAY

(Type A (model with color display))

.

Intelligent Emergency Braking system

— “Intelligent Emergency Braking system”

(P.5-85) .

Intelligent Forward Collision Warning sys-

tem

— “Intelligent Forward Collision Warning

system” (P.5-89).

.

Other information

Note that the information used in this section is

written in UK English. There are a few differ-

ences in the information for the UK and U.S.

English versions of the system.

JVI1272X

The vehicle information display

is located

For language settings, see the NissanConnect

between the tachometer and the speedometer,

and it displays the warnings and information.

The following items are also displayed if the

vehicle is equipped with them:

Owner’s Manual.

.

Cruise control

— “Cruise control” (P.5-50)

Intelligent Cruise Control (ICC)

.

— “Intelligent Cruise Control (ICC) system”

(P.5-52)

.

Lane Departure Warning (LDW) system/

Intelligent Lane Intervention system

— “Lane Departure Warning (LDW) system/

Intelligent Lane Intervention system”

(P.5-25).

Blind Spot Warning/Intelligent Blind Spot

Intervention/Intelligent Back-up Interven-

tion

— “Blind Spot Warning/Intelligent Blind

Spot Intervention/Intelligent Back-up

Intervention” (P.5-32).

.

Intelligent Emergency Braking with pedes-

trian detection system

— “Intelligent Emergency Braking with pe-

destrian detection system” (P.5-77).

2-26 Instruments and controls

INDICATORS FOR OPERATION

WAC0140X

Instruments and controls 2-27

1. No Key Detected

This warning appears when the Intelligent Key

is left outside the vehicle with the ignition

switch in the “ON” position. Make sure the

Intelligent Key is inside the vehicle.

See “Intelligent Key system” (P.3-5) for more

details.

2. Key ID Incorrect

This warning appears when the ignition switch

is pushed from the “OFF” position and the

Intelligent Key is not recognized by the system.

You cannot start the engine with an unregis-

tered key.

See “Intelligent Key system” (P.3-5).

3. Key Battery Low

This indicator appears when the Intelligent Key

battery is running out of power.

If this indicator illuminates, replace the battery

with a new one. (See “Intelligent Key battery”

(P.8-19).)

4. Key System Error: See Owner’s Manual

This warning appears if there is a malfunction

in the Intelligent Key system. If this warning

appears while the engine is stopped, it may be

impossible to start the engine.

If this warning appears while the engine is

running, you can drive the vehicle. However in

these cases, have the system checked by a

NISSAN dealer.

WAC0183X

The displayed images may differ depending on

the model.

2-28 Instruments and controls

5. Key Registration Complete

9. Engine start operation for Intelligent Key

system indicator (if I-Key battery level is low)

This indicator appears when the battery of the

Intelligent Key is low and when the Intelligent

Key system and the vehicle are not commu-

nicating normally.

If this indicator appears, touch the ignition

switch with the Intelligent Key while depressing

the brake pedal. For additional information,

refer to “Intelligent Key battery discharge” (P.5-

11).

13. Tyre Pressure Low Add Air (if equipped)

This indicator appears when a new Intelligent

Key is registered to the vehicle.

This warning (“Tire Pressure Low Add Air” and a

vehicle icon - if equipped) appears when the

low tire pressure warning light in the meter

illuminates and low tire pressure is detected.

The warning appears each time the ignition

switch is placed in the “ON” position as long as

the low tire pressure warning light remains

illuminated. If this warning appears, stop the

vehicle and adjust the pressure to the recom-

mended COLD tire pressure shown on the tire

placard. (See “Low tire pressure warning light”

(P.2-20) and “Tire Pressure Monitoring System

(TPMS)” (P.5-6).)

6. Push brake and start switch to drive

This indicator appears when the vehicle is in

the “P” (Park) position.

This indicator also appears when the vehicle

has been started using the Remote Engine

Start function (if equipped).

This indicator means that the engine will start

by pushing the ignition switch with the brake

pedal depressed. You can start the engine from

any position of the ignition switch.

10. Release Parking Brake

This warning appears when the vehicle speed

is above 7 km/h (4 MPH) and the parking brake

is applied. Stop the vehicle and release the

parking brake.

14. Variable 4 × 4 mode indicator

7. Push Ignition to OFF

This indicator shows the driving mode (ON

ROAD, ROCK, SNOW or SAND) that is selected by

the variable 4 x 4 mode select switch. (See

“Variable 4 × 4 mode select switch (except for

Mexico)” (P.5-20).)

After the Push Ignition to OFF warning illumi-

nates, the warning will illuminate if the ignition

switch is placed in the “ACC” position when the

shift lever moves into the “P” position.

11. Low Fuel

This warning appears when the fuel level in the

tank is getting low. Refuel as soon as it is

convenient, preferably before the fuel gauge

reaches the empty (0) position.

To turn off the warning, place the ignition

switch in the “ON” position and then in the

“LOCK” position.

15. Four-Wheel Drive (4WD) shift indica-

tor (4WD models)

This indicator shows the Four-Wheel Drive

(4WD) driving mode (AUTO, 4HI or 4LO) that is

selected by the 4WD shift switch. (See “Four-

Wheel Drive (4WD) (4WD models)” (P.5-16).)

There is a small reserve of fuel remaining in

the tank when the fuel gauge reaches the

empty (0) position.

8. Shift to Park

This warning appears when the ignition switch

is pushed to stop the engine with the shift lever

in any position except the “P” (Park) position.

If this warning appears, move the shift lever to

the “P” (Park) position or push the ignition

switch to the “ON” position.

12. Low Washer Fluid

This warning appears when the washer tank

fluid is at a low level. Add washer fluid as

necessary. (See “Window washer fluid” (P.8-17).)

16. Door open warning

This warning appears if any of the doors are

open or not closed securely. The vehicle icon

indicates which door is open on the display.

An inside warning chime will also sound. (See

“Intelligent Key system” (P.3-5).)

Instruments and controls 2-29

above systems.

17. Power will turn off to save the battery

27. Stop vehicle and Apply parking

brake (if equipped)

This warning appears after a period of time if

the ignition switch is in “ACC” or “ON” position.

23. Malfunction (if equipped)

This warning appears when one or more of the

following systems (if equipped) is not function-

ing properly:

This warning may appear when the battery

charge is low.

Park the vehicle as soon as possible. It is

recommended that you visit a NISSAN dealer.

18. Power turned off to save the battery

This warning appears after the ignition switch

is automatically turned OFF to save the battery.

.

Intelligent Emergency Braking

Intelligent Emergency Braking with pedes-

28. Cruise indicator

Models without Intelligent Cruise Control

(ICC) system:

This indicator shows the cruise control system

status. The status is shown by the color.

See “Cruise control” (P.5-50) for details.

19. Light reminder warning

trian detection

This warning appears when the driver side

door is opened with the headlight switch is left

ON and the ignition switch is placed in the “OFF”

or “LOCK” position. Place the headlight switch in

“OFF” or “AUTO” position. For additional infor-

mation, see “Headlight and turn signal switch”

(P.2-43).

.

Intelligent Forward Collision Warning

Lane Departure Warning (LDW)

Intelligent Lane Intervention system

Blind Spot Warning (BSW)

Intelligent Blind Spot Intervention

Rear Cross Traffic Alert (RCTA) system

Models with Intelligent Cruise Control (ICC)

system:

This indicator shows the conventional (fixed

speed) cruise control mode status. The status is

shown by the color.

If one or more of these warning appears, have

20-22. Driver assist system indicator (if equipped)

the system checked by a NISSAN dealer.

This indicator shows the status of the following

24. Wiper Mode Guidance

systems, if the vehicle is equipped with them.

This indicator shows the wiper and washer

.

Intelligent Emergency Braking

See “Conventional (fixed speed) cruise control

switch position.

Intelligent Emergency Braking with pedes-

mode” (P.5-66) for details.

The selected position is illuminated as orange

when the wiper switch position is changed.

trian detection

29. Not Available: High Camera Temp (if equipped)

.

Intelligent Forward Collision Warning

Lane Departure Warning (LDW)

Intelligent Lane Intervention system

Blind Spot Warning (BSW)

This message appears when the camera de-

tects an interior temperature of more than

40°C (104°F). For additional information, refer to

“Lane Departure Warning (LDW) system/Intelli-

gent Lane Intervention system” (P.5-25), “Blind

Spot Warning/Intelligent Blind Spot Interven-

tion/Intelligent Back-up Intervention” (P.5-32),

or “Intelligent Emergency Braking with pedes-

trian detection system” (P.5-77).

25. Lights Mode Guidance

This indicator shows the headlight switch

position.

Intelligent Blind Spot Intervention

The selected position is illuminated as orange

when the headlight switch position is changed.

For more details, see “Intelligent Emergency

Braking system” (P.5-85), “Intelligent Emergency

Braking with pedestrian detection system” (P.5-

77), “Intelligent Forward Collision Warning sys-

tem” (P.5-89), “Lane Departure Warning (LDW)

system/Intelligent Lane Intervention system”

(P.5-25), “Blind Spot Warning/Intelligent Blind

Spot Intervention/Intelligent Back-up Interven-

tion” (P.5-32).

26. Intelligent Cruise Control (ICC) in-

dicators (if equipped)

These indicators show the Intelligent Cruise

Control (ICC) system status. For additional

information, refer to “Intelligent Cruise Control

(ICC) system” (P.5-52).

The figure and color of these indicators will

change depending on the conditions of the

2-30 Instruments and controls

.

When a wheel slips

30. Not Available: Side Radar Obstruc-

tion (if equipped)

33. Extended storage fuse warning (if equipped)

The above system cannot be used in some

This warning may appear if the extended

storage fuse switch is not pushed in (switched

on). When this warning appears, push in (switch

on) the extended storage fuse switch to turn

off the warning. For more information, see

“Extended storage fuse switch” (P.8-22).

situations. (VDC operates and a wheel slips.)

This message appears when the Blind Spot

Warning (BSW)/Intelligent Blind Spot Interven-

tion/Intelligent Back-up Intervention (if

equipped)/Rear Cross Traffic Alert (RCTA) (if

equipped) systems become unavailable be-

cause a radar blockage is detected. For addi-

tional information, refer to “Blind Spot Warning/

Intelligent Blind Spot Intervention/Intelligent

Back-up Intervention” (P.5-32) or “Rear Cross

Traffic Alert (RCTA)” (P.5-45).

37. Currently not available (if equipped)

This message appears and the Intelligent Blind

Spot Intervention system and the Intelligent

Lane Intervention system will be turned off

automatically under the following conditions:

34. Headlight warning (if equipped)

This warning appears if the LED headlights are

malfunctioning. Have the system checked by a

NISSAN dealer.

.

When the VDC system is turned off.

When the ROCK, SNOW or SAND mode is

selected (variable 4 × 4 mode select switch).

.

When the 4WD shift switch is in the 4H or 4L

35. Intelligent Blind Spot Intervention/Intelligent

Lane Intervention ON indicator (if equipped)

31. Not Available: High Accelerator

Temperature (if equipped)

position. (4WD models).

“Vehicle Dynamic Control (VDC) system” (P.5-

22), “Blind Spot Warning/Intelligent Blind Spot

Intervention/Intelligent Back-up Intervention”

(P.5-32) and “Lane Departure Warning (LDW)

system/Intelligent Lane Intervention system”

(P.5-25).

This indicator appears when one or more of the

This message appears when the Intelligent

Back-up Intervention system becomes unavail-

able because of an interior temperature great-

er than approximately 40°C (104°F). For

additional information, refer to “Blind Spot

Warning/Intelligent Blind Spot Intervention/In-

telligent Back-up Intervention” (P.5-32).

following systems (if equipped) is activated.

.

Intelligent Blind Spot Intervention system

Intelligent Lane Intervention system

For more details, see “Lane Departure Warning

(LDW) system/Intelligent Lane Intervention sys-

tem” (P.5-25) or “Blind Spot Warning/Intelligent

Blind Spot Intervention/Intelligent Back-up In-

tervention” (P.5-32).

38. ECO mode system indicator (if equipped)

The ECO mode system indicator appears when

32. Not Available: Front Radar Blocked

(if equipped)

the ECO mode system is turned on.

See “ECO mode system” (P.5-99).

This message appears when the Intelligent

Cruise Control (ICC), Intelligent Emergency

Braking, Intelligent Emergency Braking with

pedestrian detection, Intelligent Emergency

Braking or Intelligent Forward Collision Warning

systems become unavailable because the front

radar is obstructed. For additional information,

refer to “Intelligent Cruise Control (ICC) system”

(P.5-52), “Intelligent Emergency Braking with

pedestrian detection system” (P.5-77), “Intelli-

gent Emergency Braking system” (P.5-85) or

“Intelligent Forward Collision Warning system”

(P.5-89).

36. Not Available: Poor Road Conditions

(if equipped)

This warning may appear when the Intelligent

Blind Spot Intervention system, the Intelligent

Lane Intervention system, or the Intelligent

Cruise Control (ICC) system is engaged.

Under the following conditions, the Intelligent

Blind Spot Intervention, the Intelligent Lane

Intervention system or the ICC system is

automatically canceled:

39. Automatic Transmission (AT) posi-

tion indicator

This indicator shows the transmission shift

position.

See “Driving with Automatic Transmission (AT)”

(P.5-12) for further details.

.

When the Vehicle Dynamic Control (VDC)

operates

Instruments and controls 2-31

TRIP COMPUTER

WAC0141X

2-32 Instruments and controls

3. Compass (if equipped)

This display indicates the heading direction of

the vehicle.

7. Current fuel consumption and average

fuel consumption (l (liter)/100 km, km/l(liter))

Current fuel consumption:

The current fuel consumption mode shows the

4. Navigation (if equipped)

current fuel consumption.

When the route guidance is set in the naviga-

tion system, this item shows the navigation

route information.

Average fuel consumption:

The average fuel consumption mode shows

the average fuel consumption since the last

reset. Resetting is done by pushing the left or

For more details, see the NissanConnect Own-

er’s Manual.

right side of the

second.

switch for longer than 1

WAC0142X

5. Vehicle speed (km/h)

The vehicle speed mode shows the current

vehicle speed and the average vehicle speed

since the last reset.

The trip computer switch is located on the left

side of the steering wheel. To operate the trip

computer, push the switch.

The average fuel consumption is also reset on

the lower display. See the NissanConnect Own-

er’s Manual.

The display is updated every 30 seconds. At

about the first 500 m (1/3 mile) after a reset, the

display shows “——”.

Each time the left or right side of the

Resetting is done by pushing the left or right

switch is pushed, the display will change.

side of the

switch for longer than 1 second.

The display item for trip computer is changed

on the lower display. For details, see the

NissanConnect Owner’s Manual.

Average vehicle speed:

The average vehicle speed display is updated

every 30 seconds. The first 30 seconds after a

reset, the display shows “——”.

8. Intelligent Cruise Control (ICC) sys-

tem (if equipped)

This mode shows the operating condition for

the Intelligent Cruise Control (ICC) system. (See

“Intelligent Cruise Control (ICC) system” (P.5-

52).)

The displayed images may differ depending on

the model.

6. Elapsed time and trip odometer (km)

Elapsed time:

1. Home

The Home mode shows the following informa-

The elapsed time mode shows the time since

the last reset. The displayed time can be reset

by pushing the left or right side of the

tion.

9. Driving aids (if equipped)

The driving aids mode shows the operating

condition for the following systems, if the

vehicle is equipped with them.

.

Vehicle speed

Navigation (if equipped)

Audio

switch for longer than

1 second. (The trip

odometer is also reset at the same time.)

Trip odometer:

.

Intelligent Emergency Braking

2. Audio

Intelligent Emergency Braking with pedes-

The trip odometer mode shows the total

distance the vehicle has been driven since the

last reset. Resetting is done by pushing the left

The audio mode shows the status of audio

trian detection

information.

For more details, see the NissanConnect Own-

er’s Manual.

.

Intelligent Forward Collision Warning

Lane Departure Warning (LDW)

or right side of the

switch for longer than 1

second. (The elapsed time is also reset at the

same time.)

Intelligent Lane Intervention system

Instruments and controls 2-33

.

Blind Spot Warning (BSW)

11. Auxiliary gauges

CLOCK AND OUTSIDE AIR TEMPERA-

TURE

Intelligent Blind Spot Intervention

For more details, see “Intelligent Emergency

Braking system” (P.5-85), “Intelligent Emergency

Braking with pedestrian detection system” (P.5-

77), “Intelligent Forward Collision Warning sys-

tem” (P.5-89), “Lane Departure Warning (LDW)

system/Intelligent Lane Intervention system”

(P.5-25) or “Blind Spot Warning (BSW) and

Intelligent Blind Spot Intervention systems”

(P.5-32).

10. Tire pressures (if equipped)

WAC0184X

The tire pressure mode shows the pressure of

WAC0190X

all four tires while the vehicle is driven.

The auxiliary gauges consist of the battery

voltage gauge, the off-road monitor and the

engine oil pressure gauge.

When the “Tire Pressure Low Add Air” warning

appears, the display can be switched to the tire

pressure mode by pushing the left or right side

The clock

and outside air temperature

are

displayed on the upper side of the vehicle

information display.

The battery voltage gauge indicates current

of the

switch.

battery voltage. (See “Voltmeter” (P.2-11).)

Clock

The tire pressure unit can be changed in the

[TPMS setting] under the [Settings] menu on

the lower display. (See the NissanConnect

Owner’s Manual.)

The off-road monitor indicates the angle of

the vehicle position up or down and left or

right. The value will be displayed on the right

side and below the gauge while the vehicle

graphic will rotate to indicate the condition

pointed up or down and left or right.

The engine oil pressure gauge indicates

current engine oil pressure. (See “Engine oil

pressure gauge” (P.2-11).)

The clock can be adjusted on the lower display.

See the NissanConnect Owner’s Manual.

Outside air temperature (°C or °F )

NOTE:

The outside air temperature is displayed in °C

After the ignition switch is placed in the “ON”

position, it may take a period of time for the

tire pressure to be displayed while the

vehicle is driven. Depending on the radio

wave circumstance, tire pressure may not

correctly be displayed.

or °F in the range of −40 to 60°C (−40 to 140°F ).

The outside temperature sensor is located in

front of the radiator. The sensor may be

affected by road or engine heat, wind direc-

tions and other driving conditions. The display

may differ from the actual outside temperature

or the temperature displayed on various signs

or billboards.

2-34 Instruments and controls

Download User Manual App

Instruments and controls -> Warning lights for Your Nissan Patrol SUV Sixth Generation (2010-2023)

Related Topics

Instruments and controls

Popular Owner Manuals

Latest Owner Manuals