Get Heater, air conditioner and audio systems -> FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC (CD) CHANGER Guide for Nissan X Trail SUV First Generation (2000-2006)

FM-AM RADIO WITH CASSETTE

PLAYER AND COMPACT DISC (CD)

CHANGER

1. CD LOAD button

2. SEEK/APS REW, APS FF/TRACK

ADJUSTING button

3. AUTOP (Automatic preset) button

4. SCAN tuning button

5. CD PLAY button

6. TAPE PLAY button

7. Radio band select button

8. DOLBY button

9. RPT (Repeat) play button

10. RADIO TUNE/FF⋅REW/AUDIO (Bass,

treble, fader, balance) ADJUSTING button

11. CD EJECT button

12. ON⋅OFF/VOL (Volume) control knob

13. Audio/Clock display

14. Station and preset (radio)/CD insert or CD

play select button

15. TAPE EJECT button

16. MENU (Bass, treble, fader, balance, clock)

button

SAA0830

4-14 Heater, air conditioner and audio systems

墌 04.6.10/T30-J/V5.0 墍

Audio main operation

Head unit :

The tape deck employs a permalloy head which

allows for improved reproduction of high fre-

quency ranges. Noise is also greatly reduced by

the combined use of the Dolby NR (Noise

Reduction) system. The auto loudness circuit

enhances the low frequency range automatically

in both radio reception and tape and CD play-

back.

ON⋅OFF/Volume control :

Turn the ignition key to ACC or ON, and then

push the ON⋅OFF/VOL (Volume) control knob

while the system is off to call up the mode (radio,

tape or CD) which was playing immediately

before the system was turned off. When no CD

or tape is loaded, the radio will come on. While

the system is on, pushing the ON⋅OFF/VOL

control knob turns the system off.

To turn the radio off, press the ON⋅OFF/VOL

control knob.

Turn the ON⋅OFF/VOL control knob to adjust

the volume.

MENU button :

Press the MENU button to change the selecting

mode as follows.

BASS → TREBLE → FADER → BALANCE →

CLOCK ON/OFF → (clock adjustment) →

RADIO → BASS

See “CLOCK” in the “2. Instruments and con-

trols” section for the clock adjustment.

To adjust Bass, Treble, Fader and Balance,

press the MENU button until the desired mode

(BASS, TREBLE, FADER or BALANCE) ap-

pears in the display. Press the TUNE (

) or SEEK ( , ) button to adjust

Bass and Treble to the desired level. Use the

TUNE or SEEK button also to adjust Fader or

Balance modes. Fader adjusts the sound level

between the front and rear speakers and Bal-

ance adjusts the sound between the right and

left speakers.

AUDIO

MODE

AUDIO CONTROL

ADJUSTING BUTTON

Center

position

BASS

(bass ad-

justment)

BAS −5 BAS 0 BAS +5

TREBLE

(treble

adjust-

ment)

TRE −5 TRE 0 TRE +5

FADER

(front/rear

balance

adjust-

ment)

FADR5

(FADER

Rear)

FAD 0

FADF5

(FADER

Front)

BALANCE

(left/right

balance

adjust-

ment)

BALL5

(BALANCE

Left)

BAL 0

BALR5

(BALANCE

Right)

Once you have adjusted the sound quality to the

desired level, press the MENU button repeatedly

until the radio, cassette tape or CD display

reappears. Otherwise, the radio, cassette tape

or CD display will automatically reappear after

about 10 seconds.

Radio operation

Radio band select :

Pushing the FM/AM button will change the band

as follows:

AM → FM1 → FM2 → AM

Heater, air conditioner and audio systems 4-15

墌 04.6.10/T30-J/V5.0 墍

When FM/AM button is pushed while the igni-

tion switch is in the ACC or ON position, the

radio will come on at the station last played.

The last station played will also come on when

the ON⋅OFF/VOL control knob is pushed to ON.

If a compact disc or tape is playing when the

FM/AM button is turned to ON, the compact

disc or tape will automatically be turned off and

the last radio station played will come on.

The FM stereo indicator ST will glow during FM

stereo reception. When the stereo broadcast

signal is weak, the radio will automatically

change from stereo to monaural reception.

TUNE (Tuning) :

WARNING

The radio should not be tuned while

driving so full attention may be given to

vehicle operation.

Use the TUNE button

or for manual

tuning. To move quickly through the channels,

hold either side of the TUNE button down for

more than 0.5 seconds.

SEEK tuning :

Pushing the SEEK button

or tunes

from high to low or low to high frequencies and

stops at the next broadcasting station.

SCAN tuning :

Pushing the SCAN tuning button tunes from low

to high frequencies and stops at each broad-

casting station for 5 seconds. Pushing the but-

ton again during this 5 second period will stop

SCAN tuning and the radio will remain tuned to

that station.

If the SCAN tuning button is not pushed within 5

seconds, SCAN tuning moves to the next sta-

tion.

Station memory operations :

Twelve stations can be set for the FM band (six

for FM1, six for FM2) and six stations can be set

for both the AM bands.

1. Tune to the desired station using the SEEK,

SCAN or TUNE button.

2. Select the desired station and keep pushing

any of the desired station/preset buttons (1

to 6) until a beep sound is heard. (The radio

mutes when the station/preset button is

pushed.)

3. The channel indicator will then come on and

the sound will resume. Memorizing is now

complete.

4. Other buttons can be set in the same manner.

If the battery cable is disconnected, or if

the fuse blows, the radio memory will be

erased. In that case, reset the desired sta-

tions.

AUTOP (Automatic preset) button :

To select the preset FM or AM, push the AUTOP

button for less than 1.5 seconds.

To preset the FM or AM, push the AUTOP

button for more than 1.5 seconds.

Cassette tape player operation

Turn the ignition key to the ACC or ON position,

and then lightly insert the cassette tape into the

tape door. The cassette tape will be automati-

cally pulled into the player.

The radio or CD will turn off (if it is on) and the

cassette tape will begin to play.

CAUTION

Do not force the cassette tape into the

tape door. This could cause player

damage.

4-16 Heater, air conditioner and audio systems

墌 04.6.10/T30-J/V5.0 墍

If the system is turned off by pushing the

ON⋅OFF/VOL control knob with the cassette

tape still in the player, the tape will resume

playing when the system is turned back on.

PLAY :

쐌 When the TAPE button is pushed with the

system turned off and a tape loaded, the

system will come on and the tape will play.

쐌 When the TAPE button is pushed with either

the radio or compact disc turned on and the

tape loaded, the compact disc or the radio

will automatically be turned off and the tape

will play.

쐌 When the TAPE button is pushed with the

TAPE playing, the tape will play the program

recorded on the reverse side.

FF (Fast Forward), REW

(Rewind) :

Push the

(fast forward) button to fast

forward the tape. To rewind the tape, push the

(rewind) button. Either the FF or REW

symbol illuminates on the right side of the display

window. To stop the FF or REW function, press

the

(fast forward) or (rewind) again,

or the TAPE button.

APS (Automatic

Program Search) FF,

APS REW :

When the

(APS FF) button is pushed

while the tape is being played, the next program

will start to play from the beginning. Push the

(APS FF) button several times to skip

through programs. The tape will advance the

number of times the button is pushed (up to nine

programs).

When the

(APS REW) button is pushed

once, the program being played starts over from

the beginning. Push the

(APS REW) but-

ton several times to skip back several selections.

The tape will go back the number of times the

button is pushed. Either the FF or REW symbol

flashes on the display window while searching

for the selection.

This system searches for the blank intervals

between selections. If there is a blank interval

within one program or there is no interval be-

tween programs, the system may not stop in the

desired or expected location.

SCAN tuning :

Push the SCAN tuning button while playing a

tape, and it stops at the next tape program for 5

seconds. Pushing the button again during this 5

second period will stop SCAN tuning and the

tape program is continued. If the SCAN tuning

button is not pushed within 5 seconds, SCAN

tuning moves to the next tape program.

Dolby NR (Noise Reduction) :

Push the Dolby NR

button for Dolby NR

encoded tapes to reduce high frequency tape

noise. The indicator will come on.

Dolby noise reduction is manufactured under

license from Dolby Laboratories Licensing Cor-

poration. Dolby NR and the double-D symbol

are trademarks of Dolby Laboratories Li-

censing Corporation.

Metal or chrome tape usage :

The cassette player will be automatically set to

high performance play when playing a metal or

chrome cassette tape.

TAPE EJECT :

When this button is pushed with the tape

loaded, the tape will be ejected.

When the tape is ejected while it is being played,

the system will be turned off.

Compact disc (CD) changer

operation

Turn the ignition key to the ACC or ON position,

push the LOAD button and insert the compact

disc into the slot with the label side facing up.

Heater, air conditioner and audio systems 4-17

墌 04.6.10/T30-J/V5.0 墍

The compact disc will be guided automatically

into the slot and will start playing.

After loading the disc, the number of tracks on

the disc will appear on the display.

If the radio or tape is already operating, it will

automatically turn off and the compact disc will

play.

CAUTION

쐌 Do not force the compact disc into

the slot. This could damage the

player.

쐌 Do not use 8 cm (3.1 in) discs.

If the system has been turned off while the

compact disc was playing, pushing the

ON⋅OFF/VOL control knob will start the com-

pact disc.

CD LOAD :

To insert a CD in the CD changer, push the

LOAD button for less than 1.5 seconds. Select

the loading slot by pushing the CD insert select

button (1 to 6), then insert the CD.

To insert 6 CDs to the CD changer in succes-

sion, push the LOAD button for more than 1.5

seconds.

The inserted slot numbers will illuminate on the

display.

CD PLAY :

When the CD6 (CD play) button is pushed with

the system off and the compact disc loaded, the

system will turn on and the compact disc will

start to play.

When the CD6 button is pushed with the com-

pact disc loaded with the tape or the radio

playing, the tape or radio will automatically be

turned off and the compact disc will start to play.

FF (Fast Forward), REW

(Rewind) :

When the

(fast forward) or (rewind)

button is pushed while the compact disc is

being played, the compact disc will play while

fast forwarding or rewinding. When the button is

released, the compact disc will return to normal

play speed.

APS (Automatic Program

Search) FF, APS REW :

When the

(APS FF) button is pushed

while the compact disc is being played, the next

program from the present one will start to play

from its beginning. Push several times to skip

through programs. The compact disc will ad-

vance the number of times the button is pushed.

(When the last program on the compact disc is

skipped through, the first program will be

played.) When the

(APS REW) button is

pushed, the program being played returns to its

beginning. Push several times to skip back

through programs. The compact disc will go

back the number of times the button is pushed.

CD PLAY select button :

To change CD, push the CD play select button

(1 to 6).

SCAN tuning :

When the SCAN tuning button is pushed for

less than 1.5 seconds while the CD is being

played, the beginning of all the CD programs in

each track will be played for 10 seconds in

sequence.

When the SCAN tuning button is pushed for

more than 1.5 seconds while the CD is being

played, the first program in all the CDs will be

played for 10 seconds.

Pushing the button again during this 10 second

period will stop SCAN tuning.

If the SCAN tuning button is not pushed within

10 seconds, SCAN tuning moves to the next

disc program.

REPEAT (RPT) :

When the RPT play button is pushed while the

4-18 Heater, air conditioner and audio systems

墌 04.6.10/T30-J/V5.0 墍

compact disc is being played, the play pattern

can be changed as follows:

The display shows the following symbols.

(no mark): ALL RPT (Repeat)

1DISC: 1 CD RPT

1: 1 TR (Track) RPT

MIX: ALL MIX

1DISC MIX: 1 CD MIX

CD EJECT :

When the CD EJECT button is pushed with the

compact disc loaded, the compact disc will be

ejected.

To eject the disc selected by the CD select

button, push the EJECT button for less than 1.5

seconds.

To eject all the discs in succession, push the

EJECT button for more than 1.5 seconds.

When this button is pushed while the compact

disc is being played, the compact disc will come

out and the system will turn off.

If the compact disc comes out and is not

removed, it will be pulled back into the slot

to protect it.

CD IN indicator :

CD IN indicator (inserted slot number) appears

on the display when the CD is loaded with the

system on.

Heater, air conditioner and audio systems 4-19

墌 04.6.10/T30-J/V5.0 墍

Heater, air conditioner and audio systems -> FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC (CD) CHANGER for Your Nissan X Trail SUV First Generation (2000-2006)

Related Topics

Popular Owner Manuals

Latest Owner Manuals