Get Access -> Electronic Engine Immobiliser Guide for Peugeot 1007 4 Door First Generation (2005-2009)

4

Programming the remote

control

ELECTRONIC ENGINE

IMMOBILISER

Following changing of the remote

control battery or disconnection of

the vehicle battery, the remote control

must be reprogrammed.

This locks the engine control system

a few moments after the ignition has

been switched off and therefore pre-

vents starting of the vehicle by any-

one who does not have the key.

The ignition key has an electronic

chip which has a special code. When

the ignition is switched on, the code is

recognised and starting is possible.

If the system does not function

correctly, the service warning light

comes on, accompanied by an

audible signal and a message on the

multifunction display.

In this case, your vehicle will not

start. Contact a PEUGEOT dealer as

soon as possible.



Wait at least one minute before

using the remote control.

Switch on the ignition.

Press button B or C for at least

ﬁve seconds within the next ten

seconds.



Switch off the ignition.

Wait at least one minute before

using the remote control.

Changing the remote control

battery

Battery ref.: CR1620/3 volts.

The remote control is now working

again.

The information "battery ﬂat" is given

by displaying of the service warning

light, accompanied by an audible

signal and a message on the multi-

function display.

To replace the battery, unclip the

casing using a coin at the notch.

Lost keys

Visit a PEUGEOT dealer with the

vehicle’s V5 registration certiﬁcate

and your personal identiﬁcation docu-

ments.

A PEUGEOT dealer will be able to

retrieve the key code and the trans-

ponder code required to order a

replacement key.

If the remote control does not work

after the battery has been changed,

re-programme the remote control.

74

4

Make a careful note of the

number on each key. The

key number is coded on the

label attached to the key.

When purchasing a secondꢀhand

vehicle, have the key codes memoꢀ

rised by a PEUGEOT dealer to enꢀ

sure that the keys in your possesꢀ

sion are the only ones which can

start the vehicle.

If the keys are lost, a PEUGEOT

dealer can rapidly supply you with

new keys.

The high frequency remote conꢀ

trol is a sensitive system; do not

operate it while it is in your pocket

as there is a possibility that it may

unlock your vehicle, without you

being aware of it.

Do not make any modiﬁcations to

the electronic engine immobiliser

system.

The remote control does not opeꢀ

rate when the key is in the ignition,

even when the ignition is switched

off, except for reprogramming.

Do not operate the deadlocking

function if there is anyone inside

the vehicle.

Driving with the doors locked may

make access to the passenger

compartment by the emergency

services more difﬁcult in an emer-

gency.

As a safety precaution (with chilꢀ

dren on board), remove the ignition

key when you leave the vehicle,

even for a short time.

Do not repeatedly press the button

of your remote control out of range

and out of sight of your vehicle.

You run the risk of stopping it from

working and the remote control

would have to be reprogrammed.

Do not throw the remote

control batteries away, they

contain metals which are

harmful to the environment.

Take them to an approved collection

point.

75

4

Programming the remote

control

ELECTRONIC ENGINE

IMMOBILISER

Following changing of the remote

control battery or disconnection of

the vehicle battery, the remote control

must be reprogrammed.

This locks the engine control system

a few moments after the ignition has

been switched off and therefore pre-

vents starting of the vehicle by any-

one who does not have the key.

The ignition key has an electronic

chip which has a special code. When

the ignition is switched on, the code is

recognised and starting is possible.

If the system does not function

correctly, the service warning light

comes on, accompanied by an

audible signal and a message on the

multifunction display.

In this case, your vehicle will not

start. Contact a PEUGEOT dealer as

soon as possible.



Wait at least one minute before

using the remote control.

Switch on the ignition.

Press button B or C for at least

ﬁve seconds within the next ten

seconds.



Switch off the ignition.

Wait at least one minute before

using the remote control.

Changing the remote control

battery

Battery ref.: CR1620/3 volts.

The remote control is now working

again.

The information "battery ﬂat" is given

by displaying of the service warning

light, accompanied by an audible

signal and a message on the multi-

function display.

To replace the battery, unclip the

casing using a coin at the notch.

Lost keys

Visit a PEUGEOT dealer with the

vehicle’s V5 registration certiﬁcate

and your personal identiﬁcation docu-

ments.

A PEUGEOT dealer will be able to

retrieve the key code and the trans-

ponder code required to order a

replacement key.

If the remote control does not work

after the battery has been changed,

re-programme the remote control.

74

4

Make a careful note of the

number on each key. The

key number is coded on the

label attached to the key.

When purchasing a secondꢀhand

vehicle, have the key codes memoꢀ

rised by a PEUGEOT dealer to enꢀ

sure that the keys in your possesꢀ

sion are the only ones which can

start the vehicle.

If the keys are lost, a PEUGEOT

dealer can rapidly supply you with

new keys.

The high frequency remote conꢀ

trol is a sensitive system; do not

operate it while it is in your pocket

as there is a possibility that it may

unlock your vehicle, without you

being aware of it.

Do not make any modiﬁcations to

the electronic engine immobiliser

system.

The remote control does not opeꢀ

rate when the key is in the ignition,

even when the ignition is switched

off, except for reprogramming.

Do not operate the deadlocking

function if there is anyone inside

the vehicle.

Driving with the doors locked may

make access to the passenger

compartment by the emergency

services more difﬁcult in an emer-

gency.

As a safety precaution (with chilꢀ

dren on board), remove the ignition

key when you leave the vehicle,

even for a short time.

Do not repeatedly press the button

of your remote control out of range

and out of sight of your vehicle.

You run the risk of stopping it from

working and the remote control

would have to be reprogrammed.

Do not throw the remote

control batteries away, they

contain metals which are

harmful to the environment.

Take them to an approved collection

point.

75

4

Complete disarming of the alarm

Complete setting and

disarming of the alarm

Press the unlocking button on the

remote control.

The direction indicators ﬂash for

two seconds.

The red indicator light on the switch

1 goes out.

Complete setting of the alarm

Switch off the ignition and get out

of the vehicle.

Lock or deadlock the vehicle.

Note: if the indicator light continues to

ﬂash after de-activation of the alarm,

it is a sign that the alarm has been

triggered during your absence. The

ﬂashing will stop when the ignition is

switched on.

The direction indicators light for

two seconds.

The red indicator light on the switch 1

ﬂashes once a second.

5 seconds later, external protection

is set.

45 seconds later, internal protection

is set.

ALARM

The alarm offers two types of

protection.

Automatic setting

The alarm is set automatically

2 minutes after the last door or the

boot is closed.

To prevent the alarm being triggered

when a door or the boot is opened,

the remote control unlocking button

must be pressed again.

-

external; the alarm sounds if

one of the doors, the bonnet

or the tailgate is opened,

internal; the alarm sounds

if there is air movement in

the passenger compartment

(a broken window or movement

within the car).

Note: when the alarm is triggered,

the siren sounds for thirty seconds.

However, after the siren stops, the

alarm remains set.

-

The alarm also has an anti-tamper

function.

If there is an attempt to tamper with

the following equipment:

When the alarm is set,

if a door, the tailgate or

the bonnet is not closed

Locking the vehicle without

alarm

To lock the vehicle without activating

the alarm (for example when washing),

insert the key in the lock, then lock it.

correctly, the siren sounds

-

the wires to the siren or the

control unit, the siren sounds

accompanied by ﬂashing of the

direction indicators.

for a moment. If the vehicle is closed

correctly in the following 45 seconds,

the alarm is set. In all cases, the

alarm is set after 45 seconds.

-

the battery, the siren sounds.

76

4

Selection of the type of

protection

Remote control failure

Unlock the doors using the key.

Open the door.

The alarm is triggered.

Switch on the ignition.

The electronic engine immobiliser

system recognises the key.

The siren stops and the alarm is

disarmed.

To set the alarm to external

protection only

If you want to leave a window partially

open, or a pet inside the vehicle, you

need to select external protection

only:

-

switch off the ignition,

within the next ten seconds,

press the control button 1 until

the warning light comes on

continuously,

Work on the battery

The alarm must not be set when the

battery is disconnected. Otherwise,

the siren will sound.

-

get out of the vehicle,

lock or deadlock the vehicle,

the direction indicators light for

two seconds,

After reconnecting the battery:

-

lock or deadlock, then unlock

the vehicle using the remote

control,

-

the red indicator light on the

switch 1 ﬂashes once a second.

-

the alarm will be operational

again the next time the vehicle

is locked or deadlocked.

To deꢀactivate external protection

only

Press the unlocking button on the

remote control.

The direction indicators ﬂash for two

seconds.

The red indicator light on the switch

1 goes out.

Do not make any modi-

ﬁcations to the alarm

system, this could result in

malfunctions.

77

4

Note: the electrical functions of

the one-touch electric windows are

deactivated approximately one minute

after the ignition is switched off.

Always remove the key from

the ignition when leaving

the vehicle, even for a short

time.

In the event of contact when opera-

ting the windows, you must reverse

the movement of the window. To do

this, press the switch concerned.

When the driver operates the

passenger window switches, he must

ensure that no one is preventing

correct closing of the window.

Safety autoꢀreverse

In automatic mode, when the window

rises and meets an obstacle, it stops

and partially lowers again.

The driver must ensure that

passengers use the electric windows

correctly.

Be aware of children when operating

the windows.

In the case of unwanted

opening of the window on

closing or if the window will

ELECTRIC WINDOWS

not rise, lower it completely

1. Driver’s electric window

switch.

2. Passenger electric window

switch.

and raise it again immediately, by

pulling the switch until the win-

dow closes completely. Continue to

press the switch for approximately

one second after closing.

Oneꢀtouch electric window

with safety autoꢀreverse

You have two options:

The safety autoꢀreverse function is not

operational during these operations.

You can close all of the

windows using the remote

-

Manual mode:

Press or pull switch 1 gently.

The window stops as soon

as the switch is released.

control

when

locking

(refer to the section "Access -

§ Remote control key").

-

Automatic mode:

The electric window switches are not

active when the door concerned is

open.

The movement of a window stops if

the door is opened. A second action

on the electric window switch will

only be taken into account when the

door is closed.

Press or pull switch 1 fully. The win-

dow opens or closes completely

when the switch is released.

Pressing the switch again stops the

movement of the window.

78

Access -> Electronic Engine Immobiliser for Your Peugeot 1007 4 Door First Generation (2005-2009)

Related Topics

Access