2001-2014 Peugeot 307 4 Door Warning Lights and Indicators User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Warning Lights and Indicators for Your Peugeot 307 4 Door 2001-2014

Service warning light  
In order to regenerate the filter, you  
are advised to drive at a speed of  
40 mph (60 km/h) or above for at  
least five minutes (until the warn-  
ing light is switched off) as soon  
as possible, when traffic conditions  
permit. If the warning light remains  
on, contact a PEUGEOT dealer.  
During regeneration of the particle  
emission filter, relay noise may be  
heard from underneath the fascia.  
- the presence of water in the diesel  
filter (Diesel)*.  
OPERATION WARNING  
LIGHTS  
This light comes on for a  
few seconds each time  
the ignition is switched on.  
A permanently lit warning light or  
one that flashes with the engine  
running, indicates an operating  
fault in the relevant unit. Some  
warning lights may be linked to  
buzzers and a message on the  
multi-function display. Do not  
ignore this warning: contact a  
PEUGEOT dealer as soon as pos-  
sible.  
If the Central STOP warning light  
comes on when you are driving,  
stop immediately where it is safe  
to do so.  
If it remains on or comes  
on when the engine is running, ac-  
companied by an audible signal and  
a message on the multifunction dis-  
play, it indicates one of the following:  
- a battery charge fault*,  
- an automatic gearbox operation fault,  
- an engine immobiliser system fault,  
- an engine management system fault,  
- a speed control system fault (cruise  
control/speed limiter),  
Risk of damage to the injection  
system.  
Contact a PEUGEOT dealer as  
soon as possible.  
- a low coolant level**.  
- a rear parking assistance system  
fault,  
Central STOP  
warning light  
This light comes on  
for a few seconds  
each time the igni-  
tion is switched on.  
- an automatic switching on of the  
lights system fault,  
- an automatic headlamp height ad-  
justment system fault,  
- a tyre under-inflation detection sys-  
tem fault,  
Stop immediately.  
Warning: wait for the engine to  
cool before topping up the level.  
The cooling system is pressurised.  
In order to avoid any risk of scald-  
ing, unscrew the cap by two turns  
to allow the pressure to drop. When  
the pressure has dropped, remove  
the cap and top up the level.  
Contact a PEUGEOT dealer.  
It is linked to the "engine oil pres-  
sure"*, "low brake fluid level" and  
"electronic brake force distribution  
fault" warning lights and the coolant  
temperature gauge.  
Stop immediately if it flashes with  
the engine running.  
Contact a PEUGEOT dealer.  
It also comes on in the event of a  
puncture, accompanied by an audi-  
ble signal and a message on the mul-  
tifunction display locating the wheel  
concerned.  
- a deflated wheel,  
- a flat remote control battery,  
- one or more door(s) open at a vehi-  
cle speed above 6 mph (10 km/h),  
- a low diesel additive reservoir level  
(Diesel),  
- a lack of engine oil,  
- the start of saturation of the particle  
emission filter (Diesel) due to ex-  
ceptionally prolonged urban driving  
conditions: low speed, long traffic  
jams, ...  
* According to country.  
** According to engine.  
18  
Handbrake, low brake  
fluid level and electronic  
brake force distribution  
fault warning light  
Seat belt unfastened/  
not fastened warning light  
Whentheignitionisswitched  
on, the light comes on if the  
driver has not fastened his  
seat belt.  
Electronic stability  
programme (ESP/ASR)  
warning light  
This comes on for a few  
seconds each time the igni-  
tion is switched on.  
Linked to the central STOP warning  
light.  
This comes on for a few seconds  
each time the ignition is switched  
With the engine running and the  
doors closed, the light switches off  
automatically after 30 seconds.  
If the seat belt is unfastened:  
- below 12 mph (20 km/h), the light  
comes on continuously,  
- above 12 mph (20 km/h) and for  
two minutes, the light flashes ac-  
companied by an audible signal of  
increasing volume. Once these two  
minutes have elapsed, the light re-  
mains on until the driver fastens his  
seat belt.  
If the light remains on or comes on  
when the engine is running and the  
vehicle is moving, it is accompanied  
by an audible signal and a message  
on the multifunction display; contact  
a PEUGEOT dealer.  
When the engine is running and the  
vehicle is moving, it flashes if the  
system is activated.  
Illumination of this light is accompa-  
nied by an audible signal and a mes-  
sage on the multifunction display  
indicating:  
that the handbrake is applied or  
has not been released correctly,  
an excessive drop in the brake fluid  
level (if the light remains on even  
with the handbrake released),  
It is lit continuously when the system  
is disarmed.  
- a malfunction of the electronic  
brake force distribution, if linked to  
the ABS warning light.  
Anti-lock braking system  
(ABS) warning light  
Emission control system  
warning light  
Stop immediately in the last two  
This light comes on for a  
few seconds each time the  
ignition is switched on.  
This comes on each time  
the ignition is switched on.  
It should switch off a few seconds  
after the engine is started.  
If the light comes on when the en-  
gine is running, accompanied by an  
audible signal and a message on the  
multifunction display, this indicates a  
malfunction of the emission control  
system.  
Contact a PEUGEOT dealer.  
If it remains on or comes on above  
8 mph (12 km/h), this indicates a  
malfunction of the ABS.  
However, the vehicle retains conven-  
tional servo-assisted braking.  
Illumination of this light is accompa-  
nied by an audible signal and a mes-  
sage on the multifunction display.  
Contact a PEUGEOT dealer as soon  
as possible.  
Contact a PEUGEOT dealer.  
19  
Air bag warning light  
Engine oil pressure  
warning light*  
Linked to the central STOP  
Low fuel level  
warning light  
This comes on for a  
few seconds each  
time the ignition is  
switched on.  
This comes on for a few  
seconds each time the igni-  
tion is switched on.  
warning light.  
Illumination of this warning light, with  
the engine running, is accompanied  
by an audible signal and a message  
on the multifunction display indicat-  
ing:  
If it comes on with the engine run-  
ning, it is accompanied by an audible  
signal and a message on the multi-  
function display.  
Stop immediately.  
If there is a lack of oil in the lubrica-  
tion circuit, top up the level.  
When this light comes on with the en-  
gine running, it is accompanied by an  
audible signal and a message on the  
multifunction display.  
When the warning light comes on, you  
have enough fuel left to drive approxi-  
mately 30 miles (50 km). The tank  
capacity is approximately 60 litres.  
- a fault in the front air bags,  
- a fault in the side air bags or curtain  
air bags.  
Contact a PEUGEOT dealer.  
Contact a PEUGEOT dealer without  
delay.  
Battery charge warning  
light*  
This comes on for a few  
seconds each time the igni-  
tion is switched on.  
Engine oil pressure warning*  
Linked to the central STOP warning  
light.  
When the engine is running, the en-  
gine oil pressure warning message is  
accompanied by an audible signal.  
Stop immediately.  
If there is a lack of oil in the lubrica-  
tion circuit, top up the level.  
Contact a PEUGEOT dealer as soon  
as possible.  
Passenger air bag  
disarmed indicator light*  
This comes on for a few  
seconds each time the igni-  
tion is switched on.  
If it comes on with the engine run-  
ning, it is accompanied by an audible  
signal and a message on the multi-  
function display.  
According to country, this warning  
light may be replaced by the service  
warning light.  
If the passager air bag is disarmed,  
the indicator light remains on.  
In all cases, if the indicator light flash-  
es, contact a PEUGEOT dealer.  
It can indicate:  
- faulty operation of the charging cir-  
cuit,  
- loose battery or starter terminals,  
- a cut or slack alternator belt,  
- an alternator fault.  
Diesel pre-heat light  
This comes on for a few  
seconds each time the igni-  
tion is switched on.  
Wait until it goes out before trying the  
starter.  
Contact a PEUGEOT dealer.  
* According to country.  
20  
Coolant temperature indicator  
Engine oil temperature gauge  
Automatic gearbox lever  
positions indicator  
Park  
Reverse  
Neutral  
Drive  
When the engine is running, this indi-  
cates the oil temperature.  
When the needle is in zone A, the  
temperature is correct.  
Manual mode:  
The temperature is too high if the  
maximum graduation is reached.  
You must stop immediately.  
When the needle is in zone B the  
temperature is too high. The central  
STOP warning light flashes,  
panied by an audible signal and a  
message on the multifunction dis-  
play.  
You must stop immediately.  
Warning: wait for the engine to cool  
before topping up the level.  
The cooling system is pressurised.  
In order to avoid any risk of scalding,  
unscrew the cap two turns to allow  
the pressure to drop.  
When the pressure has dropped, re-  
move the cap and top up the level.  
Contact a PEUGEOT dealer.  
1st gear engaged  
Contact a PEUGEOT dealer.  
2nd gear engaged  
3rd gear engaged  
4th gear engaged  
5th gear** engaged  
6th gear** engaged  
** According to model.  
21  
In the event of under-revving or over-  
revving, the gear selected flashes for  
a few seconds, then the actual gear  
engaged is displayed.  
INSTRUMENT PANEL DISPLAY  
Service indicator  
This indicates when the next service  
is due in accordance with the manu-  
facturer’s servicing schedule.  
The point at which the next service  
is due is calculated from the last indi-  
cator zero reset (see corresponding  
section). It is determined by two pa-  
rameters:  
Invalid value during manual  
operation  
- the distance travelled,  
- the time which has elapsed since  
the last service.  
This is displayed if a gear is  
not engaged correctly (selec-  
tor between two positions).  
Note: the distance remaining before  
the next service may be weighted  
by the time factor, depending on the  
user’s driving habits.  
After switching on the ignition, three  
functions are shown in succession:  
- service indicator,  
- engine oil level indicator,  
- total distance recorder (total and  
trip distances).  
Note: the total and trip distances are  
displayed for 30 seconds when the  
ignition is switched off, on opening  
the driver’s door, as well as on lock-  
ing and unlocking the vehicle.  
Automatic gearbox indicator  
lights  
"SPORT" indicator light  
This comes on when the  
"SPORT" programme on  
the automatic gearbox is se-  
lected.  
It also displays the information re-  
lating to the cruise control or speed  
limiter, when either of these is acti-  
vated (see corresponding section).  
"SNOW" indicator light  
This comes on when the  
"SNOW" programme on the  
automatic gearbox is selected.  
22  
Operation  
The distance remaining to  
the next service is less than  
500 miles (1,000 km).  
Example: 400 miles (900 km) remain  
before the next service.  
The service is overdue.  
The spanner flashes for 5 seconds  
after the ignition is switched on.  
For 5 seconds after the ignition is  
switched on, the spanner symbolis-  
ing the servicing operations comes  
on; the distance recorder display indi-  
cates the number of miles [kilometres]  
(rounded off) remaining until the next  
service.  
Example: the service is overdue by  
300 miles/km, your vehicle must be  
serviced as soon as possible.  
For 5 seconds after the ignition is  
switched on, the display indicates:  
For 5 seconds after the ignition is  
switched on, the display indicates:  
Example: 4,800 miles/km remain  
before the next service. For five sec-  
onds after the ignition is switched on,  
the display indicates:  
5 seconds after the ignition was  
switched on, the distance recorder  
resumes its normal operation and  
the spanner remains lit  
It indicates that a service must be  
carried out soon. The display indi-  
cates the total and trip distance.  
5 seconds after the ignition was  
switched on, the distance recorder  
resumes its normal operation and the  
spanner remains lit. The display indi-  
cates the total and trip distance.  
Note: the spanner may also come on  
if more than two years have elapsed  
since the last service.  
5 seconds after the ignition was  
switched on, the distance recorder  
resumes its normal operation and  
the display indicates the total and trip  
distance.  
23  
Service indicator zero re-set  
Dipstick  
Engine oil level indicator  
When the ignition is switched on,  
the engine oil level is indicated for  
a few seconds, after the service  
information.  
There are 2 marks on the  
dipstick:  
- never exceed level A,  
- in position B, top up the  
level via the oil filler cap,  
using the type of oil suit-  
ed to your engine.  
Oil level correct  
A
B = min.  
Lack of oil  
Flashing of "OIL"  
linked with the serv-  
Your PEUGEOT dealer carries out  
this operation after each service.  
However, if you carry out the service  
yourself, the re-set procedure is as  
follows:  
ice warning light,  
accompanied by an  
audible signal and  
a message on the  
multifunction display, indicates a lack of  
oil which could damage the engine.  
Switch off the ignition,  
If the lack of oil is confirmed by a  
check using the dipstick, it is essen-  
tial that the level is topped up.  
Press and hold the trip recorder  
re-set button,  
Switch on the ignition.  
The display begins a countdown.  
Oil level gauge fault  
When the display shows "=0", re-  
lease the button; the spanner disap-  
pears.  
Important: after this operation, if you  
wish to disconnect the battery, lock  
the vehicle and wait for at least five  
minutes, otherwise the zero re-set  
will not be registered.  
Flashing of "OIL "  
indicates a malfunc-  
tion of the engine oil  
level gauge.  
Contact a PEUGEOT dealer.  
The level read will only be correct if  
the vehicle is on level ground and  
the engine has been off for more  
than 15 minutes.  
24  
In the event of under-revving or over-  
revving, the gear selected flashes for  
a few seconds, then the actual gear  
engaged is displayed.  
INSTRUMENT PANEL DISPLAY  
Service indicator  
This indicates when the next service  
is due in accordance with the manu-  
facturer’s servicing schedule.  
The point at which the next service  
is due is calculated from the last indi-  
cator zero reset (see corresponding  
section). It is determined by two pa-  
rameters:  
Invalid value during manual  
operation  
- the distance travelled,  
- the time which has elapsed since  
the last service.  
This is displayed if a gear is  
not engaged correctly (selec-  
tor between two positions).  
Note: the distance remaining before  
the next service may be weighted  
by the time factor, depending on the  
user’s driving habits.  
After switching on the ignition, three  
functions are shown in succession:  
- service indicator,  
- engine oil level indicator,  
- total distance recorder (total and  
trip distances).  
Note: the total and trip distances are  
displayed for 30 seconds when the  
ignition is switched off, on opening  
the driver’s door, as well as on lock-  
ing and unlocking the vehicle.  
Automatic gearbox indicator  
lights  
"SPORT" indicator light  
This comes on when the  
"SPORT" programme on  
the automatic gearbox is se-  
lected.  
It also displays the information re-  
lating to the cruise control or speed  
limiter, when either of these is acti-  
vated (see corresponding section).  
"SNOW" indicator light  
This comes on when the  
"SNOW" programme on the  
automatic gearbox is selected.  
22  
In the event of under-revving or over-  
revving, the gear selected flashes for  
a few seconds, then the actual gear  
engaged is displayed.  
INSTRUMENT PANEL DISPLAY  
Service indicator  
This indicates when the next service  
is due in accordance with the manu-  
facturer’s servicing schedule.  
The point at which the next service  
is due is calculated from the last indi-  
cator zero reset (see corresponding  
section). It is determined by two pa-  
rameters:  
Invalid value during manual  
operation  
- the distance travelled,  
- the time which has elapsed since  
the last service.  
This is displayed if a gear is  
not engaged correctly (selec-  
tor between two positions).  
Note: the distance remaining before  
the next service may be weighted  
by the time factor, depending on the  
user’s driving habits.  
After switching on the ignition, three  
functions are shown in succession:  
- service indicator,  
- engine oil level indicator,  
- total distance recorder (total and  
trip distances).  
Note: the total and trip distances are  
displayed for 30 seconds when the  
ignition is switched off, on opening  
the driver’s door, as well as on lock-  
ing and unlocking the vehicle.  
Automatic gearbox indicator  
lights  
"SPORT" indicator light  
This comes on when the  
"SPORT" programme on  
the automatic gearbox is se-  
lected.  
It also displays the information re-  
lating to the cruise control or speed  
limiter, when either of these is acti-  
vated (see corresponding section).  
"SNOW" indicator light  
This comes on when the  
"SNOW" programme on the  
automatic gearbox is selected.  
22  
Operation  
The distance remaining to  
the next service is less than  
500 miles (1,000 km).  
Example: 400 miles (900 km) remain  
before the next service.  
The service is overdue.  
The spanner flashes for 5 seconds  
after the ignition is switched on.  
For 5 seconds after the ignition is  
switched on, the spanner symbolis-  
ing the servicing operations comes  
on; the distance recorder display indi-  
cates the number of miles [kilometres]  
(rounded off) remaining until the next  
service.  
Example: the service is overdue by  
300 miles/km, your vehicle must be  
serviced as soon as possible.  
For 5 seconds after the ignition is  
switched on, the display indicates:  
For 5 seconds after the ignition is  
switched on, the display indicates:  
Example: 4,800 miles/km remain  
before the next service. For five sec-  
onds after the ignition is switched on,  
the display indicates:  
5 seconds after the ignition was  
switched on, the distance recorder  
resumes its normal operation and  
the spanner remains lit  
It indicates that a service must be  
carried out soon. The display indi-  
cates the total and trip distance.  
5 seconds after the ignition was  
switched on, the distance recorder  
resumes its normal operation and the  
spanner remains lit. The display indi-  
cates the total and trip distance.  
Note: the spanner may also come on  
if more than two years have elapsed  
since the last service.  
5 seconds after the ignition was  
switched on, the distance recorder  
resumes its normal operation and  
the display indicates the total and trip  
distance.  
23  
Service indicator zero re-set  
Dipstick  
Engine oil level indicator  
When the ignition is switched on,  
the engine oil level is indicated for  
a few seconds, after the service  
information.  
There are 2 marks on the  
dipstick:  
- never exceed level A,  
- in position B, top up the  
level via the oil filler cap,  
using the type of oil suit-  
ed to your engine.  
Oil level correct  
A
B = min.  
Lack of oil  
Flashing of "OIL"  
linked with the serv-  
Your PEUGEOT dealer carries out  
this operation after each service.  
However, if you carry out the service  
yourself, the re-set procedure is as  
follows:  
ice warning light,  
accompanied by an  
audible signal and  
a message on the  
multifunction display, indicates a lack of  
oil which could damage the engine.  
Switch off the ignition,  
If the lack of oil is confirmed by a  
check using the dipstick, it is essen-  
tial that the level is topped up.  
Press and hold the trip recorder  
re-set button,  
Switch on the ignition.  
The display begins a countdown.  
Oil level gauge fault  
When the display shows "=0", re-  
lease the button; the spanner disap-  
pears.  
Important: after this operation, if you  
wish to disconnect the battery, lock  
the vehicle and wait for at least five  
minutes, otherwise the zero re-set  
will not be registered.  
Flashing of "OIL "  
indicates a malfunc-  
tion of the engine oil  
level gauge.  
Contact a PEUGEOT dealer.  
The level read will only be correct if  
the vehicle is on level ground and  
the engine has been off for more  
than 15 minutes.  
24  
Trip recorder zero reset  
button  
Lighting rheostat  
With the ignition on, press the button  
until the zeros appear.  
Pressing the button enables you to  
alternate between the distance re-  
corder and cruise control or speed  
limiter displays, when either of these  
is activated.  
With the lights on, press the button to  
vary the intensity of the lighting of the  
instruments and controls. When the  
lighting reaches the minimum (or maxi-  
mum) setting, release the button then  
press it again to increase (or reduce)  
the brightness.  
As soon as the lighting is of the re-  
quired brightness, release the button.  
25  
TRIP COMPUTER  
System which provides current infor-  
mation concerning the route travelled  
(range, consumption, ...).  
The trip computer data is the follow-  
ing:  
Zero reset  
Monochrome screen A  
- the range,  
- the current consumption,  
- the distance travelled,  
- the average consumption,  
- the average speed.  
Data displays  
Press the control for more than  
two seconds to reset the distance  
travelled, the average consump-  
tion and the average speed to  
Press the button, located at the  
end of the wipers stalk, to display  
the various items of trip computer  
data in succession.  
26  
Data displays  
- the route "2" tab with:  
- the distance  
travelled,  
- the average  
consumption,  
- the average speed,  
TRIP COMPUTER  
System which provides current infor-  
mation concerning the route travelled  
(range, consumption, …).  
for the second route.  
Monochrome screen C  
Route zero reset  
Press the button, located at the  
end of the wipers stalk, to display  
the various trip computer tabs in  
succession:  
Colour screen  
- the current information  
tab with:  
- the range,  
- the current  
consumption,  
- the distance  
remaining to be  
travelled,  
When the route required is dis-  
played, press the control for more  
than two seconds.  
- the route "1" tab with:  
- the distance  
travelled,  
- the average  
consumption,  
- the average speed,  
Routes "1" and "2" are independent  
but their use is identical.  
Route "1" permits, for example, daily  
calculations, and route "2" monthly  
calculations.  
for the first route.  
27  
A few definitions…  
Range  
(km or miles)  
This indicates the number  
Current consumption  
(l/100 km or km/l or mpg)  
Distance remaining to be  
travelled  
(km or miles)  
This is the average quantity  
of fuel consumed over the  
of miles (or kilometres)  
which can still be travelled with the  
fuel remaining in the tank in relation  
to the average consumption over the  
last few miles (kilometres) travelled.  
This is the distance remain-  
ing to be travelled to the final destina-  
tion. It is either calculated instantly by  
the navigation system if guidance is  
activated, or entered by the user.  
If the distance is not entered, dashes  
are displayed in place of the digits.  
last few seconds.  
This function is only displayed  
from 20 mph (30 km/h).  
This figure may increase fol-  
lowing a change of driving  
style or relief, resulting in a  
significant change in the cur-  
rent consumption.  
Average speed  
(km/h or mph)  
This is the average speed  
calculated since the last trip  
computer zero reset (ignition  
on).  
Average consumption  
(l/100 km or km/l or mpg)  
This is the average quan-  
tity of fuel consumed since  
the last trip computer zero reset.  
When the range falls below 20 miles  
(30 km), dashes are displayed. After  
filling with at least 5 litres of fuel, the  
range is recalculated and is displayed  
when it exceeds 60 miles (100 km).  
Distance travelled  
(km or miles)  
This indicates the dis-  
tance travelled since the  
last trip computer zero  
reset.  
If dashes are displayed con-  
tinuously while driving in  
place of the digits, contact a  
PEUGEOT dealer.  
28  

Related Topics

Instrument Panel Dials Operation Warning Lights Temperature and Gauge Indicators Instrument Panel Display Service indicator Service indicator zero re-set Engine oil level indicator Trip recorder zero reset button Lighting rheostat Trip Computer Trip Computer Menu Diagnostics Menu

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot