2010-2020 Peugeot Ion 4 Door In the event of a breakdown -> Changing a bulb User Manual

MY CAR USER MANUAL

In the event of a breakdown -> Changing a bulb for Your Peugeot Ion 4 Door First Generation (2010-2020)

In the event of a breakdown  
Changing a bulb  
Front lamps  
The headlamps have polycarbonate  
lenses with a protective coating:  
F
do not clean them using a dry  
or abrasive cloth, nor with a  
detergent or solvent product,  
use a sponge and soapy water or a  
pH neutral product,  
when using a high pressure washer  
on persistent marks, do not keep  
the lance directed towards the  
lamps or their edges for too long,  
so as not to damage their protective  
coating and seals.  
F
F
1. Direction indicators (W21W - 21 W).  
2. Sidelamps (W5W - 5 W).  
3. Main beam headlamps (HB3 - 60 W).  
4. Dipped beam headlamps (H11 - 55 W).  
5. Front foglamps (H8 - 35 W).  
6. Daytime running lamps  
(P13W - 13 W).  
Changing a bulb should only be done  
after the headlamp has been switched  
off for several minutes (risk of serious  
burns).  
F
Do not touch the bulb directly with  
your fingers, use a lint-free cloth.  
It is imperative to use only anti-  
ultraviolet (UV) type bulbs to avoid  
damaging the headlamp.  
Always replace a failed bulb with a  
new bulb with the same type and  
specification.  
126  
In the event of a breakdown  
Access to bulbs  
To replace a failed bulb, you must first remove  
the lamp.  
To remove the lamp:  
F
F
Lift the cover B, using a screwdriver  
protected by a cloth.  
Slacken fixing screw C until the head of the  
screw touches the trim.  
F
F
Remove the bumper retaining clips, using a  
screwdriver.  
Carefully lift the bumper.  
F
F
Open the bonnet.  
Press tab A to release the connector.  
8
127  
In the event of a breakdown  
F
F
Slacken fixing screw D, while holding the  
bumper away.  
Slacken fixing screw E.  
F
Pull the lamp towards you, and disengage  
the tab F to remove it completely.  
128  
In the event of a breakdown  
Changing sidelamp bulbs  
Changing main beam headlamp  
bulbs  
Changing direction indicator  
bulbs  
F
Turn the bulb holder to the left and pull  
it out.  
F
F
Turn the bulb holder to the left and pull it out.  
Remove the bulb by pressing on the  
tongue.  
F
Turn the bulb holder to the left and pull  
it out.  
F
Pull the bulb out and and change it.  
To reassemble, carry out these operations in  
reverse order.  
F
Pull the bulb out and change it.  
F
Change the bulb.  
To refit, carry out these operations in reverse  
order.  
For reassembly, carry out these operations in  
reverse order.  
Amber coloured bulbs must be replaced  
with bulbs of identical specifications  
and colour.  
8
129  
In the event of a breakdown  
Changing dipped beam headlamp Changing front foglamp bulbs /  
bulbs  
daytime running lamp bulbs  
F
F
Turn the bulb holder to the left and pull it out.  
Remove the bulb by pressing on the  
tongue.  
F
F
F
Put the front wheels onto full lock, to  
facilitate access.  
Remove the clips securing the protective  
covers on the bulb holders.  
Move the cover aside.  
F
F
Turn the bulb holder (A for the front fog  
lamp, B for the daytime running lamp) to  
the left and pull it out.  
F
Change the bulb.  
Pull the bulb out and change it.  
To refit, carry out these operations in reverse  
order.  
To reassemble, carry out these operations in  
reverse order.  
130  
In the event of a breakdown  
Rear lamps  
1. Brake lamps / Sidelamps  
Changing integrated direction  
indicator side repeater bulbs  
(WY5W - 5 W)  
Access to bulbs  
(21 W / 15 W or LEDs).  
2. Direction indicators (WY21W - 21 W).  
3. Reversing lamps (W21W - 21 W).  
F
F
Remove the two screws.  
Disengage the lamp unit by pulling it  
towards you.  
F
F
F
Push the repeater towards the rear and  
disengage it.  
Turn the bulb holder to the left and pull  
it out.  
Pull the bulb out and change it.  
To reassemble, carry out these operations in  
reverse order.  
In some weather conditions (e.g. low  
temperature or humidity), the presence  
of misting on the internal surface of the  
glass of the headlamps and rear lamps  
is normal; it disappears after the lamps  
have been on for a few minutes.  
8
Amber coloured bulbs, such as the  
direction indicators, must be replaced  
with bulbs of identical specification and  
colour.  
131  
In the event of a breakdown  
Changing a direction indicator  
bulb  
Changing a reversing lamp bulb  
Changing brake lamp / sidelamp  
bulbs (21 W / 15 W)  
F
F
Turn the bulb holder to the left and pull it out.  
Pull out the bulb and change it.  
F
F
Turn the bulb holder to the left and pull it out.  
Pull the bulb out and replace it.  
F
F
Turn the bulb holder to the left and pull it out.  
Pull the bulb out and replace it.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
Changing brake lamp / sidelamp  
LEDs  
All work on the LED lamps must be carried out  
by a PEUGEOT dealer or qualified workshop.  
132  
In the event of a breakdown  
Changing a foglamp bulb  
(W21W - 21W)  
Third brake lamp (W5W - 5W)  
Changing number plate lamp  
bulbs (W5W - 5W)  
F
F
F
Remove the two screws.  
Pull out the bulb-holder.  
Pull out the bulb and change it.  
F
F
F
Push the cover inwards.  
Turn the bulb holder and pull it out.  
Remove the bulb and change it.  
F
F
Remove the cover.  
Turn the bulb holder to the left and pull it  
out.  
To refit, carry out these operations in reverse  
order.  
To refit, carry out these operations in reverse  
order.  
F
Pull the bulb out and change it.  
To refit, carry out these operations in reverse  
order.  
8
133  

Related Topics

In the event of a breakdown

Ancillaries battery
Temporary puncture repair kit
Spare wheel
Snow chains
Changing a fuse
Towing the vehicle