2010-2020 Peugeot Ion 4 Door Instruments User Manual

MY CAR USER MANUAL

Instruments for Your Peugeot Ion 4 Door First Generation (2010-2020)

Instruments  
Instrument panel  
Panel bringing together the various gauges and indicators for the operation of the vehicle.  
Screen  
Gauges and indicators  
1. State of charge indicator for the main  
4. Screen.  
A. Total distance recorder.  
battery.  
5. Screen control button.  
Display the various functions in turn.  
Reset the function selected (trip recorder  
or service indicator).  
B. Trip distance recorder (Trip A or B).  
C. Instrument panel lighting dimmer.  
D. Distance remaining to the next service.  
E. Time remaining to the next service.  
F. Under-inflation detection.  
Drive selector position indicator.  
2. Energy consumption / generation  
indicator.  
3. Speedometer.  
Adjust the level of the lighting dimmer.  
Temporary engine brake reduction  
indicator.  
G. Remaining range.  
10  
Instruments  
Indicator and warning lamps  
1
Visual indicators informing the driver that  
a system is in operation, is deactivated or has  
a fault.  
Associated warnings  
The illumination of certain warning lamps may  
be accompanied by an audible signal.  
The warning lamps may come on continuously  
(fixed) or flash.  
When the ignition is switched on  
Certain warning lamps may come on in  
one of two modes. Only by relating the  
type of lighting to the operating status  
of the vehicle can it be ascertained  
whether the situation is normal or  
whether a fault has occurred.  
Certain warning lamps come on for a few  
seconds when the vehicle's ignition is  
switched on.  
These same warning lamps go off after a  
few seconds.  
If you notice one of these warning lamps  
remaining on, refer to the information on the  
warning lamp in question.  
11  
Instruments  
Operation indicator lamps  
If one of the following indicator lamps comes on in the instrument panel, this confirms that the corresponding system has come into operation.  
Warning / indicator lamp State  
Cause  
Action / Observations  
Left-hand  
Flashing with audible  
The lighting stalk is pushed down.  
direction indicator signal.  
Right-hand  
Flashing with audible  
The lighting stalk is pushed up.  
direction indicator signal.  
Hazard warning  
lamps  
Flashing with audible  
signal.  
The hazard warning lamps switch,  
located on the dashboard, has been  
operated.  
The left-hand and right-hand direction indicators and  
their associated indicator lamps flash simultaneously.  
Sidelamps and/  
or dipped beam  
headlamps  
On fixed.  
The sidelamps and/or dipped beam  
headlamps are on.  
Main beam  
headlamps  
On fixed.  
On fixed.  
The lighting stalk is pulled towards  
you.  
Pull the stalk to return to dipped beam headlamps.  
Front foglamps  
The front foglamps are switched on.  
Turn the ring on the stalk rearwards twice to switch off  
the front foglamps.  
Rear foglamp  
On fixed.  
The rear foglamp is switched on.  
Turn the ring on the stalk rearwards to switch off the  
rear foglamp.  
12  
Instruments  
Warning / indicator lamp State  
Cause  
Action / Observations  
1
Ready  
On fixed,  
The vehicle is ready to move off and  
you can press the accelerator.  
The illumination period corresponds to the powering-  
up of the vehicle.  
(ready to move  
off)  
accompanied by an  
audible signal when it  
comes on.  
Parking brake  
On fixed.  
The parking brake is applied or not  
properly released.  
Release the parking brake to switch off the warning  
lamp, keeping your foot on the brake pedal.  
Observe the safety recommendations.  
For more information on the Parking brake, refer to  
the corresponding section.  
Main battery  
charge (normal  
or fast)  
On fixed.  
Flashing.  
The main battery is on charge.  
On completion of the charge, the lamp goes off.  
Check the connection of the charging cable.  
The charging cable is connected to  
the vehicle but the main battery is not  
yet charging.  
13  
Instruments  
Deactivation indicator lamps  
If one of the following indicator lamps comes on, this confirms that the corresponding system has been switched off intentionally.  
This may be accompanied by an audible signal.  
Warning / indicator lamp State  
Cause  
Action / Observations  
Passenger's  
airbag system  
On fixed, on the  
centre console.  
The control switch, located in the  
glove box, is set to the OFF position.  
The passenger's front airbag is  
deactivated.  
Set the control switch to the ON position to activate  
the passenger's front airbag. In this case, do not fit a  
child seat in the rear-facing position.  
Remember to check the state of the control switch  
before starting your vehicle.  
ESP/ASR  
On fixed.  
The ESP/ASR off switch, located at  
Press the button to activate the ESP/ASR.  
the bottom of the dashboard (driver's The ESP/ASR system is automatically activated on  
side) is activated.  
starting the vehicle.  
The ESP/ASR is deactivated.  
ESP: electronic stability programme  
ASR: anti-slip regulation.  
14  
Instruments  
Warning lamps  
1
When the engine is running or the vehicle is being driven, illumination of one of the following warning lamps indicates a fault which requires action on  
the part of the driver.  
Any fault resulting in the illumination of a warning lamp must be investigated further.  
If you encounter any problems, do not hesitate to contact a PEUGEOT dealer or a qualified workshop.  
Warning / indicator lamp State  
Cause  
Action / Observations  
Braking  
On fixed.  
The braking system fluid level has  
dropped significantly.  
or  
You must stop as soon as it is safe to do so.  
Top up with brake fluid listed by PEUGEOT.  
If the problem persists, have the system checked by a  
PEUGEOT dealer or qualified workshop.  
Braking assistance system fault.  
+
On fixed, associated  
with the ABS warning  
lamp.  
The electronic brake force distribution You must stop as soon as it is safe to do so.  
(EBFD) system has a fault.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Anti-lock  
Braking System  
(ABS)  
On fixed.  
The anti-lock braking system has  
a fault.  
The vehicle retains conventional braking.  
Drive carefully at reduced speed and contact a  
PEUGEOT dealer or a qualified workshop without  
delay.  
15  
Instruments  
Warning / indicator lamp State  
Cause  
Action / Observations  
Electronic  
stability  
Flashing.  
Activation of the ESP/ASR systems.  
The systems optimise traction and improve the  
directional stability of the vehicle.  
programme  
and anti-slip  
regulation  
(ESP/ASR)  
Adapt your driving and moderate your speed.  
On fixed.  
Fault in the ESP/ASR systems.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
+
Electric power  
steering  
On fixed.  
On fixed.  
The electric power steering has a  
fault.  
Drive carefully at reduced speed.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
12 V battery  
charge  
The 12 V battery charging circuit has  
a fault (dirty or loose terminals, slack, started.  
The warning lamp should go off when the motor is  
transformer fault, etc.).  
If it does not go off, contact a PEUGEOT dealer or  
qualified workshop.  
Door(s) open  
On fixed,  
A door or the boot is still open.  
Close the door or boot.  
accompanied by an  
audible signal.  
16  
Instruments  
Warning / indicator lamp State  
Cause  
Action / Observations  
1
Under-inflation  
On fixed.  
The tyre pressure for one or more  
wheels is too low.  
Check the tyre pressures as soon as possible.  
This check should preferably be done with the tyres  
cold.  
You must reinitialise the system after every adjustment  
of one or more tyre pressures and after replacing one  
or more wheels.  
For more information on the Under-inflation  
detection, refer to the corresponding section.  
Flashing then fixed.  
The system has a fault and/or one  
or more wheels does not have a  
detected sensor.  
The tyre pressures are no longer monitored.  
Have the system checked by a PEUGEOT dealer or a  
qualified workshop.  
Front seat belt  
not fastened /  
unfastened  
On fixed, then  
The driver and/or the front passenger Pull the strap, then insert the tongue in the buckle.  
flashing, accompanied has not fastened or has unfastened  
by an audible signal.  
On fixed.  
their seat belt.  
Right-hand  
rear seat belt  
unfastened  
The right-hand rear passenger has  
unfastened their seat belt.  
Pull the strap then insert the tongue in the buckle.  
Left-hand  
rear seat belt  
unfastened  
On fixed.  
The left-hand rear passenger has  
unfastened their seat belt.  
17  
Instruments  
Warning / indicator lamp State  
Cause  
Action / Observations  
Airbags  
On temporarily.  
When you switch on the ignition, this  
warning lamp comes on for a few  
seconds, then goes off.  
If it does not go off, contact a PEUGEOT dealer or a  
qualified workshop.  
On fixed.  
On fixed.  
On fixed.  
Fault with one of the airbag or seat  
belt pretensioner systems.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Protection  
system for the  
main battery  
The state of charge of the main  
battery is too low or the temperature  
of the main battery is too low...  
The power from the motor is limited.  
Charge the main battery as soon as possible.  
If the warning lamp does not go off, contact a  
PEUGEOT dealer or qualified workshop.  
Self-diagnosis  
system of the  
main electrical  
circuit  
Fault in the main electrical circuit.  
You must stop as soon as it is safe to do so.  
Have it checked by a PEUGEOT dealer or a qualified  
workshop.  
Reduction of the Flashing.  
engine brake  
The main battery is fully charged, the Anticipate your braking as much as possible: use the  
engine brake is reduced temporarily. brake pedal to slow down or stop the vehicle.  
18  
Instruments  
Main battery state of charge indicator  
1
Display  
Low energy alerts  
Four successive alerts indicate that the energy  
available in the main battery is dropping to a  
low level:  
-
2 bars of the state of charge gauge in the  
instrument panel, on and flashing: starting  
to use the reserve.  
-
-
The last bar in the state of charge gauge  
flashing.  
The last bar disappears: display of the  
range disappears; the heating and air  
conditioning are switched off.  
-
Display of this warning lamp in  
the instrument panel: progressive  
reduction in the power available  
from the motor.  
The state of charge of the main battery is  
displayed continuously in the instrument panel.  
19  
Instruments  
Energy consumption / generation indicator  
A system that informs the driver of the level of energy consumption or generation of the main battery.  
"Neutral" position  
Energy consumption  
"Charge" zone  
The needle moves to the left in proportion to  
the level of charge sent to the main battery,  
during periods of deceleration and braking.  
On switching on the ignition, your vehicle  
neither consumes nor generates energy in its  
electric traction system: the needle is in the  
"neutral" position (provided that the heating and  
air conditioning are off).  
The needle moves to the right in proportion to  
the energy consumption by the vehicle.  
"Eco" zone  
In cold weather, the capacity for  
regeneration via braking is reduced.  
The needle is in this zone when the vehicle is  
used so as to moderate electric consumption  
and optimise its range.  
20  
Instruments  
Instrument panel screen  
1
When the ignition switch is in the "ON" position, press button A repeatedly to display the following information in turn.  
Distance recorder  
Trip distance recorder (Trip A or B)  
System for measuring the total distance  
travelled by the vehicle during its life.  
Press button A.  
Each of these trip recorders indicates the  
distance travelled since the last reset.  
Press button A to display the desired trip.  
Reset to zero  
With the ignition on and either trip A or B  
displayed, press the button for more than  
2 seconds.  
The total distance appears in the screen.  
21  
Instruments  
Lighting dimmer  
Service indicator  
System which informs the driver when the  
next service is due in accordance with the  
manufacturer's servicing schedule.  
The point at which the next service is due is  
calculated from the last service indicator zero  
reset.  
This point can be indicated in one of two ways:  
-
-
the miles (km) remaining,  
the time remaining to the next service.  
System for manual adjustment of the  
brightness of the instruments and controls in  
relation to the exterior brightness.  
With the lighting on or off, press button A to  
select the function, then hold down to change  
the intensity of the lighting of the instruments  
and controls in "day" or "night" mode.  
The intensity of the lighting increases each time  
button A is pressed.  
When the lighting reaches the maximum  
setting, press again to change to the minimum  
setting.  
When the lighting reaches the required  
intensity, release button A.  
Operation  
1. The screen indicates that 620 miles  
(1000 km) or 1 month remain before the  
next service.  
2. The screen indicates that the date for the  
service has been exceeded.  
Every time the ignition is switched on,  
the service spanner is displayed for a  
few seconds to remind you that a service  
should be carried out as soon as possible.  
3. Once the service has been carried out, the  
distance or the number of months to the  
next service is displayed again.  
When the ignition is switched on, press  
button A several times in succession until the  
service indicator is displayed in the desired  
units.  
The setting is saved when you release button A  
and retained when the ignition switch is turned  
to OFF.  
22  
Instruments  
1
Resetting the service indicator to zero  
After each service, the service indicator should  
be rest to zero.  
The procedures is as follows:  
The display of "---", indicating that the  
service date has arrived, comes on  
automatically after a certain time and  
distance travelled. The screen then  
indicates the time remaining before the  
next service is due.  
F
F
Switch off the ignition (switch in the LOCK  
or ACC position).  
Press the reset button A several times in  
succession until the service indicator is  
displayed.  
F
F
Press and hold the reset button for a few  
seconds until the spanner flashes.  
Press the reset button while the spanner is  
flashing to change the display from "---" to  
"CLEAR".  
The distance (or time) remaining before the  
next service is due is displayed.  
23  
Instruments  
Under-inflation detection  
Range indicator  
You have to reinitialise the under-inflation  
detection system after adjusting one or more  
tyre pressures or after changing one or more  
wheels.  
This function gives an estimate of the number  
of miles (km) that your vehicle can still cover,  
based on the recent conditions of use (driving  
style, use of heating, air conditioning...).  
Selecting the set of wheels and  
tyres fitted  
If you have previous registered a second set  
of wheels and tyres with sensor, you have to  
select the corresponding set in the instrument  
panel screen after fitting them.  
Carry out the following procedure to do this.  
F
F
Press button A to select the system.  
Press and hold button A for at least  
3 seconds.  
Carry out the following procedure to do this.  
F
F
Press button A to select the system.  
Press and hold button A for more than  
10 seconds, to change from set of tyres  
and wheels 1 to set 2 or the other way  
round.  
When the remaining range falls to a low level,  
"- - -" is displayed in the instrument panel.  
There is an audible signal and the under-  
inflation warning lamp flashes slowly until the  
initialisation is complete.  
24  

Related Topics

Instrument panel
Indicator and warning lamps
Operation indicator lamps
Main battery state of charge indicator
Energy consumption / generation indicator
Distance recorder
Trip distance recorder
Lighting dimmer
Service indicator
Range indicator