Get QUICK HELP -> Changing a bulb Guide for Peugeot Partner Van 2008-2014

Changing a bulb

The bulbs must be changed with

the ignition off or with the battery

disconnected. Wait approximately

3 minutes after changing the bulb

before reconnecting the battery.

Check that the lamps operate correctly

after each operation.

High pressure washing

When using this type of washing

on stubborn dirt, do not persist on

the headlamps, the lamps and their

edges to avoid damaging their coating

and seals.

Types of bulb

Various types of bulb are ﬁtted to your

vehicle. To remove them:

Type A

All glass bulb: pull gently

as it is ﬁtted by pressure.

Type B

Bayonet bulb: press

on the bulb then turn it

anticlockwise.

CHANGING A BULB

Open the bonnet. To access the bulbs,

reach behind the headlamp unit.

Carry out the operations in reverse

order to reﬁt each bulb and check that

the bonnet is closed securely.

Halogen bulbs must be changed

with the headlamp off. Wait a few

minutes (risk of serious burns).

Do not touch the bulb directly with your

ﬁngers, use lint-free cloths.

It is normal for condensation to form

inside the headlamps. Regular use of

the vehicle eliminates this misting.

Type C

Halogen bulb: release the

retaining spring from its

housing.

Type D

Light emitting diode (LED):

for replacement of the

daytime running lamps,

contact a PEUGEOT dealer

or a qualiﬁed workshop.

Changing a bulb

FRONT LAMPS

1. Dipped / Main beam headlamps

Type C, H4 - 55W

2. Sidelamps

Type A, W5W - 5W

3. Direction indicators

Type B, PY21W - 21W (amber)

- Remove the centre cover by

pulling the ﬂexible rubber tab.

- Remove the cover by pulling the

ﬂexible rubber tab.

- Remove the cover by pulling the

ﬂexible rubber tab.

- Disconnect the electrical

connector.

- Release the retaining tab.

- Change the bulb taking care

to align the metal part with the

grooves on the lamp.

- Remove the bulb holder ﬁtted by

pressure by pulling the connector.

- Change the bulb.

- Ensure that the cover is reﬁtted

correctly all round to assure

correct sealing.

- Turn the bulb holder a quarter

turn anticlockwise.

- Remove the bulb by pressing

it lightly while turning it

anticlockwise.

- Change the bulb.

- Reposition the retaining tab.

- Ensure that the cover is reﬁtted

correctly all round to assure

correct sealing.

- Ensure that the cover is reﬁtted

correctly all round to assure

correct sealing.

7

Changing a bulb

4. Foglamps

Type C, H1 - 55W

Front / Rear

SIDE REPEATER

COURTESY LAMPS

-

Remove the three clips and the screw

securing the wheelarch liner, located

below the bumper.

Type A, WY5W - 5W (amber)

Type A, 12V5W - 5W

-

Move the wheelarch liner upwards.

-

Push the repeater towards the rear

and disengage it by pulling the

front.

Contact a PEUGEOT dealer to

obtain a new repeater which is

a sealed component.

To reﬁt, engage the repeater

towards the rear and bring it

towards the front.

-

Unclip the lens by sliding a

screwdriver in the slots on each

side of the courtesy lamp.

Pull the bulb out and change it.

Clip the lens in its housing and

ensure that it is secured correctly.

Remove the foglamp by removing the

screw, which can be accessed via the

hole provided for this purpose in the

bumper, using a Torx^©30 screwdriver.

Unclip the foglamp by squeezing the clip

to release it.

Remove the foglamp from the outside.

Turn the yellow cover a 1/4 turn to open.

Separate the clips which secure the base

of bulb on each side to release the bulb.

-

Remove the bulb by pulling, keeping it

straight.

Insert the new bulb, reposition the clips

around the base of the bulb and carry

out the operations in reverse order to put

the lamp unit and the bumper back in

position.

Changing a bulb

REAR LAMPS

For more information concerning the

bulbs, refer to the "Types of bulb".

-

Identify the faulty bulb then open

the rear doors to 180°.

Refer to the "Access" section of

chapter 2.

Remove the two ﬁxing bolts using

the screwdriver stored in the tool kit

under the right-hand seat.

Pull the lamp unit from the outside.

Holding the lamp, disconnect

the electrical connector.

-

Move aside the 4 tabs then extract

the bulb holder.

Remove the faulty bulb by

pressing it lightly while turning it

anticlockwise.

1. Brake lamps/sidelamps

Type B, P21/5W - 21/5W

2. Direction indicators

Type B, PY21W - 21W (amber)

3. Reversing lamps

Type B, P21W - 21W

-

When removing the lamp unit:

-

Change the bulb.

-

with tailgate, pull the lamp unit

towards the centre of the vehicle,

with hinged doors, pull the lamp

unit towards you.

4. Foglamps

Type B, P21W - 21W

-

High pressure washing

When reﬁtting, take care to

reposition the tabs and the supply

wire correctly to avoid trapping the

wire.

When using this type of washing

on stubborn dirt, do not persist on

the headlamps, the other lamps

and their edges to avoid damaging

their coating and seals.

After changing the rear direction

indicator bulb, the reinitialisation time is

above 2 minutes.

7

Changing a bulb

NUMBER PLATE LAMPS

THIRD BRAKE LAMP

Type A, W5W - 5W

Type A, W 16 W - 16 W

With tailgate

-

With hinged doors

-

Unscrew the two nuts.

Push the pins.

If necessary, disconnect the

connector to remove the lamp.

Change the bulb.

Disengage the plastic lens using a

screwdriver.

Change the bulb.

-

Unclip the interior trim.

Disconnect the connector by

moving aside its tab.

-

Replace the plastic lens and press

on it.

-

Turn the bulb holder a quarter turn

anticlockwise.

Change the bulb.

Put the bulb holder back in place

and reconnect the connector.

Put the trim back in place.

-

Download User Manual App

QUICK HELP -> Changing a bulb for Your Peugeot Partner Van 2008-2014

Related Topics

QUICK HELP

Popular Owner Manuals

Latest Owner Manuals