2019-2024 Porsche Taycan 2 Door Porsche InnoDrive (PID) -> Operating principle User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Porsche InnoDrive (PID) -> Operating principle for Your Porsche Taycan 2 Door First Generation (2019-2024)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Porsche InnoDrive (PID)
201
Cornering and stationary vehicles
Fig. 148: Cornering (C) and stationary vehicles (D)
When driving into and out of bends, vehicles will not
be detected or will be detected too late, or the sys-
tem will react to vehicles in adjacent lanes.
A stationary vehicle or obstacle that appears sud-
denly in the detection range of the radar sensor,
such as after a vehicle in front changes lanes or at
the end of a traffic jam, can only be detected by
Adaptive Cruise Control (ACC) to a limited extent.
Vehicles with large overhangs
Fig. 149: Vehicles with large overhangs
If there is a vehicle in front with a long overhang
(such as a timber lorry), the radar sensor may possi-
bly not detect the end of the vehicle or detect it
incorrectly.
Responding to warning messages
Always heed any warning and information messages
displayed in the vehicle.
> Please refer to chapter "Warning and information
messages" on page 271.
Operating principle
Porsche InnoDrive (PID) is a driver assistance sys-
tem that assists the driver when driving on well-
surfaced country roads and motorways.
Using navigation data as well as data from radars
and cameras, PID detects both the area directly
around the vehicle and the route ahead, determines
the best possible driving strategy in advance and
adapts the speed accordingly.
PID can assist the driver in the following situations:
Vehicle driving ahead
If a vehicle was detected ahead, PID brakes if the
vehicle is driving slower than the set desired speed
and keeps the distance from the vehicle ahead con-
stant in the preselected range. PID can continue
braking until your vehicle is stationary and starts
driving again automatically as soon as the vehicle in
front drives off again. A detected vehicle and the fact
that the vehicle has started driving again will be in-
dicated on the instrument cluster.
In bends
Navigation data and vehicle information is used to
adapt the speed to the road ahead.
Tight bends detected in advance are displayed on
the instrument cluster and the speed of the vehicle
is reduced in good time. The speed calculated for the
bend is also indicated through the speed prediction
system. If no bend ahead warning is displayed, the
speed will only be reduced slightly or will not be re-
duced at all. Vehicle handling in bends is also influ-
enced by the driving mode selected.
At roundabouts, junctions and on uphill and
downhill slopes
When navigation is active or when the driver indi-
cates in good time, PID reduces the speed before the
vehicle starts to change direction. A corresponding
display appears on the instrument cluster.
Information
When route guidance is active in the navigation
system, PID always orients itself according to the
proposed route. If route guidance is not active, it
adapts to the most plausible route.
On roads with speed limits
PID uses navigation data and data from cameras
(traffic sign recognition) to automatically detect the
speed limit within the system limits and changes the
desired speed accordingly.
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
Porsche InnoDrive (PID)
202
Speed limits detected in advance are displayed on
the instrument cluster and the speed of the vehicle
is reduced in good time. If a speed limit is not de-
tected in advance, the speed will not be reduced
until the vehicle is driving past the detected traffic
sign.
Consideration of speed limits is active automatically
when PID is activated.
At Stop and Yield signs
When approaching Stop and Yield signs, a message
appears in the instrument cluster and the speed is
reduced if the traffic signs are stored in the naviga-
tion data. It is up to the driver, however, to brake the
vehicle to a standstill.
If the driver accidentally continues driving at a Stop
sign, PID switches to passive mode and can be acti-
vated again afterwards by the driver.
If the driver continues driving at a Yield sign, PID re-
mains active, passes the Yield sign at a reduced
speed and accelerates again to the previously set
speed as soon as the traffic situation allows it. The
previously set speed can be resumed again immedi-
ately by pressing RESUME.
Controls
Fig. 150: Control stalk for driver assistance systems
R Switch systems on/off and open the options menu
S Open the options menu (when the system is switched
on)
1 Set/increase the desired speed
2 Reduce the desired speed
3 RESUME: Resume control, adopt speed/confirm speed
limit
4 CANCEL: Interrupt control
Display elements
Fig. 151: PID display
A Own speed
B Event up ahead: Display on speedometer and via sym-
bols (or one of the symbols)
C Set speed
D Status display
Status display symbols
Symbol Meaning
PID is passive.
PID is passive at set desired speed.

Related Topics

Popular Owner Manuals