2025-2026 Porsche Taycan 2 Door 12-volt battery -> Supplying external power from another vehicle User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

12-volt battery -> Supplying external power from another vehicle for Your Porsche Taycan 2 Door Second Generation (2025-2026)

A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
12-volt battery
284
– Max. charging voltage: 14.8 V (even in the
event of a fault with the 12 V lithium battery
disconnected; no voltage peaks permitted)
– Max. charging current: 90 A
e If in doubt, contact your Porsche partner.
e Observe the instructions of the charger
manufacturer.
e Ensure adequate ventilation when charging the
12 V lithium battery.
1. Open the bonnet.
> Please refer to chapter "Opening and closing
the bonnet and tailgate" on page 153.
2. Remove the plastic refer to
chapter "Installing and removing the plastic cov-
er in the front luggage compartment" on
page 155.
3. Fold open the cap on the positive terminal for
jump-lead starting +.
4. Connect the red positive cable of the charger to
the positive terminal for jump-lead starting +.
5. Connect the black negative cable of the charger
to the ground point –.
6. Switch on the charger.
7. After charging the battery, first switch off the
charger and then disconnect it.
8. Close the cap on the positive terminal for jump-
lead starting +.
9. Install the plastic cover. Please refer to
chapter "Installing and removing the plastic cov-
er in the front luggage compartment" on
page 155.
For recommendations on a suitable charger:
e Contact your Porsche partner.
Supplying external power from another
vehicle
WARNING
Unsuitable jump leads
and incorrect procedures
Supplying external power using unsuitable jump
leads or following incorrect procedures can cause
short circuits. Short circuits can cause fires.
e Use only standard jump leads with sufficient
cross section and completely insulated terminal
clamps. Follow the instructions provided by the
jump lead manufacturer.
e The vehicles must not touch, otherwise current
may flow as soon as the positive terminals are
connected.
e Ensure that conductive jewellery (e.g. rings,
chains, watch straps) does not come into contact
with live parts of the vehicle.
e Never connect jump leads directly to the 12 V
lithium battery or other electrical components.
Only connect jump leads to the jump-lead start-
ing terminals.
NOTICE
Exhaustively discharged
12 V lithium battery
Risk of damage when supplying external power to an
exhaustively discharged 12 V lithium battery.
e If you suspect that the 12 V lithium battery is
exhaustively discharged, do not supply power
from an external source.
NOTICE
External power supply or
emergency starting
Emergency starting and supplying external power
can severely damage the vehicle electronics.
e Do not supply external power or initiate emer-
gency starting.
e Contact a qualified specialist workshop. Porsche
recommends a Porsche partner as they have
trained workshop personnel and the necessary
parts and tools.
1. Open the bonnet. Please refer to
chapter "Perform emergency unlocking of the
bonnet" on page 58.
2. Remove the plastic cover. Please refer to
chapter "Installing and removing the plastic cov-
er in the front luggage compartment" on
page 155.
Fig. 226: 12 V lithium battery terminals
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
12-volt battery
285
3. Fold open the cap on the positive terminal for
jump-lead starting +.
4. Connect the red positive cable to the positive
terminal for jump-lead starting +.
5. Connect the red positive cable to the positive
terminal of the donor battery.
6. Connect the black negative cable to the negative
terminal of the donor battery.
7. Connect the black negative cable to the ground
point–.
8. Allow the engine of the donor vehicle to run at a
higher engine speed.
9. Charge the 12 V lithium battery from the exter-
nal power supply (min. 5 minutes).
The electrical system is reactivated
automatically.
10.Ready for operation:
First, disconnect the black negative cable from
the ground point – then from the negative ter-
minal of the donor battery.
11.Ready for operation:
Disconnect the red positive cable from the pos-
itive terminal of the donor battery first, then from
the positive terminal for jump-lead starting +.
12.Close the cap on the positive terminal for jump-
lead starting +.
13.Install the plastic cover. Please refer to
chapter "Installing and removing the plastic cov-
er in the front luggage compartment" on
page 155.
14.To continue charging the 12 V lithium battery:
Charge the 12 V lithium battery using the
charger. Please refer to chapter "Charging the 12
V battery using the charger" on page 283.
– or –
Establish operational readiness. Please refer to
chapter "Starting, driving and stopping the ve-
hicle" on page 236.
Replacing the 12 V lithium battery
WARNING
Danger of fire due to un-
suitable 12 V lithium
battery
In addition to significant malfunctions of the vehicle
electrical system, use of an unsuitable 12 V lithium
battery or its incorrect installation may in excep-
tional cases cause a fire (e.g. during charging).
e Never attempt to replace the 12 V lithium bat-
tery yourself. Only have the 12 V lithium battery
of this vehicle replaced with a 12 V lithium bat-
tery explicitly specified by Porsche for this ve-
hicle. The use of other lithium or lead-acid
batteries results in significant malfunctions in-
cluding total failure of the electrical system.
e Always have the 12 V lithium battery replaced by
a qualified specialist workshop. Porsche recom-
mends a Porsche partner as they have trained
workshop personnel and the necessary parts and
tools.
e Observe the disposal instructions for lithium
batteries.
Power interruption
Following a temporary power interruption, some
equipment has to be reinitialised.
1. Store the end position for the power windows.
> Please refer to chapter "Windows" on
page 277.
2. Registering wheels and tyres in Tyre Pressure
Monitoring (TPM).
> Please refer to chapter "Tyres and Wheels"
on page 249.

Related Topics

Popular Owner Manuals