Get Practical Advice Guide for Renault Clio 4 Door Fifth Generation (2019-2025)

Section 5: Practical Advice

Puncture, emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wheel trim, wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2

5.4

5.7

5.8

5.9

Tyres (tyre and wheel safety, use in winter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11

Headlights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.14

Rear lights and side lights (replacing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.15

Indicator lights (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.17

Interior lighting (changing bulbs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.18

Remote control key: battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.20

Card: battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.22

Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.24

Fitting a radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.27

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.28

Fuses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.29

Wiper blades: replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.33

Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.35

Operating faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.37

5.1

PUNCTURE, EMERGENCY SPARE WHEEL (1/2)

In case of puncture

If the emergency spare wheel has been stored for several years, have it

checked by your Dealer to ensure that it is safe to use.

Depending on the vehicle, a tyre infla-

tion kit or emergency spare wheel is

provided (refer to the following pages).

Vehicle fitted with an emergency spare wheel that differs from the

other wheels:

Vehicle fitted with a tyre pressure

loss warning system

– Never fit more than one emergency spare wheel to the same vehicle.

– Replace the emergency spare wheel as soon as possible with a wheel identi-

cal to the original one.

In the event of under-inflation (punc-

tures, under-inflation etc.), the

warning light appears on the instrument

panel. ➥ 2.38.



– When this is fitted to the vehicle, which must only be a temporary measure, the

driving speed must not exceed the speed indicated on the label on the wheel.

– Fitting an emergency spare wheel may alter the way the vehicle usually runs.

Avoid sudden acceleration or deceleration and reduce your speed when cor-

nering.

– If you need to use snow chains, fit the emergency spare wheel to the rear axle

and check the tyre pressure.

If the vehicle is parked on the hard shoulder, you must warn other road

users of your vehicle’s presence with a warning triangle or with other de-

vices as per the legislation applying to the country you are in.

5.2

PUNCTURE, EMERGENCY SPARE WHEEL (2/2)

1

2

B

A

3

D

4

C

– remove the tool kit 4;

Emergency spare wheel

To get to it:

– remove the emergency spare wheel

(A or B, depending on the vehicle).

– open the boot;

– depending on the vehicle, lift up the

movable floor and the luggage com-

partment mat 1;

– depending on the vehicle, remove

the cover 2 from the tool kit 4 by slid-

ing it (movement C or D);

– unscrew the central mounting 3 (lo-

cated, depending on the vehicle,

under the jack) anti-clockwise;

On vehicles equipped with emer-

gency spare wheel B, the punctured

wheel may not be stored in place

of the emergency spare wheel B.

The 4 tool kit must be attached

using the central attachment 3 and

the punctured tyre must be placed

in the luggage compartment.

5.3

TYRE PRESSURE KIT (1/3)

Do not attempt to use the

inflation kit if the tyre has

been damaged as a result

of driving with a puncture.

The kit is only approved for

inflating the tyres of the ve-

hicle originally equipped

with the kit.

B

You should therefore carefully check

the condition of the tyre sidewalls

before any operation.

It must never be used to inflate

the tyres of another vehicle, or any

other inflatable object (rubber ring,

rubber boat, etc.).

A

Driving with underinflated, flat or

punctured tyres can be dangerous

and may make the tyre impossible

to repair.

Avoid spillage on skin when han-

dling the repair product bottle. If

droplets do leak out, rinse them off

with plenty of water.

This repair is temporary.

Keep the repair kit away from chil-

dren.

A tyre which has been punctured

should always be inspected (and re-

paired, where possible) as soon as

possible by a specialist.

Do not dispose of the empty bottle

in the countryside. Return it to your

approved dealer or to a recycling or-

ganisation.

The kit repairs tyres when

tread A has been dam-

aged by objects smaller

than 4 mm. It cannot repair

all types of puncture, such as cuts

larger than 4 mm, or cuts in tyre

sidewall B.

When taking a tyre which has been

repaired using this kit to be replaced,

you must inform the specialist.

The bottle has a limited service

life which is indicated on its label.

Check the expiry date.

When driving, vibration may be felt

due to the presence of the repair

product injected into the tyre.

Ensure also that the wheel rim is in

good condition.

Contact an approved dealer to re-

place the inflation tube and repair

product bottle.

Do not pull out the foreign body

causing the puncture if it is still in

the tyre.

5.4

TYRE PRESSURE KIT (2/3)

With the engine running and the

parking brake applied,

– Disconnect any accessories previ-

ously connected to the vehicle’s ac-

cessories sockets;

If a minimum pressure of 1.8 bar is

not reached after 15 minutes, repair

is not possible; do not drive the ve-

hicle but contact an approved dealer.

– refer to the information on the in-

flation kit compressor located in

the luggage compartment of the ve-

hicle and follow the instructions;

– inflate the tyre to the recommended

pressure ➥ 4.11 ;

– after a maximum of 15 minutes, stop

inflating and read the pressure (on

pressure gauge 2).

1

2

Before using this kit, park

the vehicle at a sufficient

distance from traffic, switch

on the hazard warning

lights, apply the handbrake, ask all

passengers to leave the vehicle and

keep them away from traffic.

Note: while the bottle is emptying

(approximately 30 seconds), the

pressure gauge 2 will briefly indicate

a pressure of 6 bar, then the pres-

sure drops;

Depending on the vehicle, in the event

of a puncture, use the kit located in the

boot or underneath the luggage com-

partment carpet.

– Adjust the pressure: to increase it,

continue inflation with the kit. To

reduce it, press the button 1.

Vehicle fitted with a tyre pressure

loss warning system

In the event of under-inflation (punc-

If the vehicle is parked on

the hard shoulder, you must

warn other road users of

tures, under-inflation etc.), the



warning light appears on the instrument

panel. ➥ 2.38.

your vehicle’s presence

with a warning triangle or with other

devices as per the legislation apply-

ing to the country you are in.

5.5

TYRE PRESSURE KIT (3/3)

– Start immediately and drive at a

speed between 12 to 37 mph (20 to

60 km/h) in order to distribute the

product evenly in the tyre; after driv-

ing a distance of 2 miles (3 km), stop

and check the pressure.

3

– If the pressure is higher than 1.3 bar

but lower than the recommended

pressure (refer to the label affixed to

the edge of the driver’s door), adjust

it. Otherwise, contact an approved

dealer: the tyre cannot be repaired.

Please be aware that a

poorly tightened or miss-

ing valve cap can make the

tyres less airtight and may

lead to pressure loss.

Always use valve caps identical to

those fitted originally and tighten

them fully.

Precautions when using the

kit

The kit should not be operated for more

than 15 consecutive minutes.

The container must be replaced after

the first use even if liquid remains

inside.

Once the tyre is correctly inflated,

remove the kit: unscrew the inflation

adapter slowly from the container 3 to

prevent any product spatter and store

the container in plastic packaging to

prevent product leaks.

Following repair with the kit,

do not travel further than

120 miles (200 km). In addi-

tion, reduce your speed and

under no circumstances exceed

48 mph (80 km/h). The sticker,

which you must affix in a prominent

position on the dashboard, reminds

you of this.

Depending on the country or local

legislation, a tyre repaired with the

inflation kit may need to be replaced.

– Affix the driving recommendation

label (located under the container) to

the dashboard where the driver can

see it.

– Put the kit away.

Nothing should be placed

around the driver’s feet

as such objects may slide

under the pedals during

sudden braking manoeuvres and

obstruct their use.

– At the end of this initial inflation op-

eration, air will still escape from the

tyre. You must drive a short distance

in order to seal the hole.

5.6

TOOLS

Jack 2

2

Fold it correctly before refitting it in its

housing (ensure that the wheelbrace is

correctly positioned).

A

B

Hubcap tool 3

This tool is used to remove the wheel

trims.

D

1

3

Wheel bolt guide 4

To finish loosening or starting to tighten

the wheel bolts.

C

4

5

Tow eye 5

➥ 5.35

The tools included in the tool kit depend

on the vehicle.

Tool kit A is located in the tray under

the luggage compartment carpet.

Wheelbrace 1

Locks or unlocks the wheel bolts and

tow eye 5.

Depending on the vehicle, remove the

cover B from the tool kit A by sliding it

(movement C or D). After use, ensure

the tools are correctly stored.

Ensure correct positioning and locking

(movement C or D) of cover B.

Do not leave the tools unsecured inside the vehicle as they may come

loose under braking. After use, check that all the tools are correctly

clipped into the tool kit, then position it correctly in its housing: risk of

injury.

If bolts are supplied with the emergency spare wheel, you must use these bolts

only for the emergency spare wheel.

The jack is designed for wheel changing purposes only. Under no circumstances

should it be used for carrying out repairs underneath the vehicle or to gain access

to the underside of the vehicle.

5.7

WHEEL TRIM, WHEEL

A

1

2

C

B

D

Remove the wheel trim using hubcap

tool 1 (located in the tool kit) by en-

gaging the hook in the opening near

valve 2.

To refit it, align it with valve 2. Push the

retaining hooks in fully, starting with

side A near the valve, followed by B

and C, finishing at D opposite the valve.

Do not leave the tools un-

secured inside the vehicle

as they may come loose

under braking. After use,

check that all the tools are correctly

clipped into the tool kit, then posi-

tion it correctly in its housing: risk of

injury.

5.8

CHANGING A WHEEL (1/2)

Start cranking the jack by hand, posi-

tioning the 4 jack support plate in the

slightly indented groove underneath

the vehicle, located between the two

notches 5 and in the direction of the

arrow 3.

Vehicles equipped with a jack

and wheelbrace

If necessary, remove the wheel trim.

Use the wheelbrace 1 to slacken off the

wheel bolts. Position it so as to be able

to push from above.

1

5

4

Continue to crank the jack so that the

baseplate is correctly positioned (it

should be underneath the vehicle and

aligned with the jack head).

Place the jack 2 horizontally. The jack

head must be lined up with the sill clos-

est to the wheel concerned and indi-

cated by the arrow 3.

3

Turn it a few times to lift the wheel off

the ground.

2

Switch on the hazard warn-

ing lights.

Keep the vehicle away from

traffic and on a level surface

where it will not slip.

Apply the parking brake and engage

a gear (first or reverse, or P for auto-

matic transmissions).

Ask all the passengers to leave the

vehicle and keep them away from

traffic.

If the vehicle is parked on

the hard shoulder, you must

warn other road users of

your vehicle’s presence

with a warning triangle or with other

devices as per the legislation apply-

ing to the country you are in.

5.9

CHANGING A WHEEL (2/2)

Undo the bolts and take off the wheel.

Vehicle fitted with a tyre pressure

loss warning system

Fit the emergency spare wheel on the

central hub and turn it to locate the

mounting holes in the wheel and the

hub.

In the event of under-inflation (punc-

tures, under-inflation etc.), the

warning light appears on the instrument

panel. ➥ 2.38.



Tighten the bolts, checking that the

wheel is correctly positioned on its hub.

Lower the jack.

With the wheel on the ground, tighten

the bolts fully and have the tightness of

the bolts checked and the emergency

spare wheel pressure checked as soon

as possible.

Do not leave the tools un-

secured inside the vehicle

as they may come loose

under braking. After use,

check that all the tools are correctly

clipped into the tool kit, then posi-

tion it correctly in its housing: risk of

injury.

If bolts are supplied with the emer-

gency spare wheel, you must use

these bolts only for the emergency

spare wheel.

The jack is designed for wheel

changing purposes only. Under no

circumstances should it be used for

carrying out repairs underneath the

vehicle or to gain access to the un-

derside of the vehicle.

If you have a puncture, re-

place the wheel as soon as

possible.

Atyre which has been punc-

tured should always be inspected

(and repaired, where possible) by a

specialist.

5.10

TYRES (1/3)

Tyre and wheel safety

When the tyre tread has been worn

to the level of the warning strips, they

become visible 2: it is then neces-

sary to replace your tyres because the

tread rubber is now only 1.6 mm deep

at most, resulting in poor road hold-

ing on wet roads.

The tyres are the only contact between

the vehicle and the road, so it is essen-

tial to keep them in good condition.

2

You must make sure that your tyres

con- form to local road traffic regula-

tions.

An overloaded vehicle, long journeys

by motorway, particularly in very hot

weather, or continual driving on poorly

surfaced minor roads will lead to more

rapid tyre wear and affect safety.

1

Maintaining the tyres

The tyres must be in good condition

and the tread form must have sufficient

depth; tyres approved by our Technical

Department have wear warning strips 1

which are indicators moulded into

the tread at several points.

Incidents which occur when

driving, such as striking the

kerb, may damage the tyres

and wheel rims, and could

also lead to misalignment of the

front or rear axle geometry. In this

case, have the condition of these

checked by an approved dealer.

5.11

TYRES (2/3)

Pressures should be checked when the

tyres are cold; ignore higher pressures

which may be reached in hot weather

or following a fast journey.

Vehicle fitted with a tyre pressure

loss warning system

Tyre pressures

Adhere to the tyre pressures (including

the emergency spare wheel). The tyre

pressures should be checked at least

once a month and additionally before

any long journey (refer to the label af-

fixed to the edge of the driver’s door).

In the event of under-inflation (punc-

tures, under-inflation etc.), the

warning light appears on the instrument

panel. ➥ 2.38.



If tyre pressures cannot be checked

when the tyres are cold, assume an in-

crease of 0.2 to 0.3 bar (or 3 PSI).

Never deflate a hot tyre.

Emergency spare wheel

➥ 5.2, ➥ 5.9.

Changing wheels around

This practice is not recommended.

Incorrect tyre pressures

lead to abnormal tyre wear

and unusually hot running.

These are factors which

may seriously affect safety and lead

to:

– poor road holding;

– risk of bursting or tread separa-

tion.

Please be aware that a

poorly tightened or miss-

ing valve cap can make the

tyres less airtight and lead

to pressure loss.

The pressure depends on the load

and the speed of use. Adjust the

pressure according to the condi-

tions of use (refer to the label affixed

to the edge of the driver’s door).

Always use valve caps identical to

those fitted originally and tighten

them fully.

5.12

TYRES (3/3)

Snow or Winter tyres

Fitting new tyres

Use in winter

We would recommend that these be

fitted to all four wheels to ensure that

your vehicle retains maximum adhe-

sion.

Chains

For safety reasons, fitting snow

chains to the rear axle is strictly for-

bidden.

Warning: These tyres sometimes have

a specific direction of rotation and a

maximum speed index which may be

lower than the maximum speed of your

vehicle.

Chains cannot be fitted to tyres which

are larger than those originally fitted to

the vehicle.

For your safety, please re-

spect the speed limit.

One-way tyres

Studded tyres

When they need to be re-

placed, only tyres of the

same make, size, type and profile

should be used on a single axle.

An one-way tyre must only be fitted in

one direction. You must observe this di-

rection.

This type of equipment may only be

used for a limited period and as laid

down by local legislation. It is neces-

sary to observe the speed specified by

current legislation.

If an one-way tyre must be fitted in the

opposite to its direction of rotation fol-

lowing a puncture, drive with caution,

particularly on a wet road, because the

tyre specifications will not be adapted.

They must either have a load ca-

pacity and speed rating at least

equal to those of the original

tyres, or be recommended by an

authorised dealer.

These tyres must, at a minimum, be

fitted to the two front wheels.

Failure to heed these instructions

could endanger your safety and

affect your vehicle’s roadworthi-

ness.

Risk of loss of control of the ve-

hicle.

In all cases, we would recommend

that you contact an approved Dealer

who will be able to advise you on

the choice of equipment which is

most suitable for your vehicle.

Chains may only be fitted

to tyres of the same size

as those originally fitted to

your vehicle.

5.13

FRONT HEADLIGHTS: replacing the bulbs

LED front fog lights/

cornering lights 3

(depending on the vehicle)

2

Consult an authorised dealer.

1

Additional lights

If you wish to fit fog lights to your ve-

hicle, please see an authorised dealer.

3

Direction indicators/dipped

beam headlights/LED main

beam headlights 1

Please see an authorised dealer.

Any operation on (or modi-

fication to) the electrical

system must be performed

LED daytime running lights/

side lights 2

(depending on the vehicle)

by an approved dealer

since an incorrect connection might

damage the electrical equipment

(harness, components and in par-

ticular the alternator). In addition,

your Dealer has all the parts re-

quired for fitting these units.

Please see an authorised dealer.

5.14

REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (1/3)

1

2

3

5

4

– release the light assembly from out-

side the vehicle by pulling towards

the rear;

Refitting

LED side light/brake light 1

Consult an approved dealer

To refit, proceed in the reverse order,

taking care not to damage the wiring.

– remove the 4 bulb holder by un-

screwing it a quarter of a turn, then

replace the bulb.

Direction indicators 5

– Open the boot;

Bulb type: WY16W.

– remove the trim 2;

– unscrew the nut 3;

The bulbs are under pres-

sure and can break when

replaced.

To comply with current legislation, or

as a precaution, you can obtain an

emergency kit from your approved

dealer containing a set of spare

bulbs and fuses.

Risk of injury.

5.15

REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (2/3)

7

9

6

8

9

Fog lights and reversing

High level brake light 7

Number plate lights 8

lights 6

Consult an approved dealer.

– Unclip the light by pressing tab 9;

Consult an approved dealer

– remove the light cover to gain access

to the bulb.

Bulb type: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.16

REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (3/3)

11

10

LED number plate lights 10

(depending on vehicle)

LED side repeaters11

(depending on vehicle)

Consult an approved Dealer.

Consult an approved dealer.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.17

INTERIOR LIGHTING: changing bulbs (1/2)

1

2

1

Courtesy light

Map reading lights 2

Consult an authorised dealer.

Courtesy light fitted with diffusers 1

Unclip the lens (using a flat-blade

screwdriver or similar).

Remove the bulb concerned.

Bulb type: W5W.

The bulbs are under pres-

sure and can break when

replaced.

Risk of injury.

5.18

INTERIOR LIGHTING: changing bulbs (2/2)

5

4

3

Luggage compartment light

Glovebox light

Courtesy mirror lights 5

Unclip the light 3 by pressing the tab on

its left side (using a flat-bladed screw-

driver or similar).

Unclip the light 4 by pressing the tab on

its left side (using a flat-bladed screw-

driver or similar).

Please consult an authorised dealer.

Ambient lighting

Please consult an authorised dealer.

Remove the bulb concerned.

Bulb type: W5W.

5.19

REMOTE CONTROL KEY: BATTERY: battery (1/2)

2

1

Note: It is not advisable to touch the

electronic circuit in the key cover when

replacing the battery.

Replacing the battery

Open the case at slot 1 using a flat-

blade screwdriver or similar, and re-

place the battery 2, observing the type

and polarity shown on the back of the

cover.

When refitting, ensure that the cover is

correctly clipped on and the screw tight-

ened.

When they need to be re-

placed, be sure to use

the same or equivalent

type of battery (consult an

Approved Dealer).

The batteries are available from ap-

proved Dealers, and their service

life approximately two years.

Check that there is no dye on the

battery: risk of an incorrect electri-

cal contact.

5.20

REMOTE CONTROL KEY: BATTERY: battery (2/2)

Operating faults

If the battery is too weak to ensure cor-

rect operation, you will still be able to

start and lock/unlock the vehicle

➥ 1.14.

Precautions relating to

batteries:

Do not throw away your used bat-

teries; give them to an organisation

responsible for collecting and recy-

cling batteries.

– keep (new or used) bat-

teries out of reach of chil-

dren;

– do not swallow batteries;

When replacing:

Risk of chemical burns which

may lead to death.

– make sure that the batter-

ies are correctly inserted.

– if ingested or inserted into any

part of the body, consult a doctor

as soon as possible.

Risk of explosion.

– if the flap does not close cor-

rectly, do not use and keep out of

reach of children.

5.21

CARD: battery (1/2)

1

A

The batteries are available from ap-

proved Dealers, and their service

life approximately two years. Check

that there is no dye on the battery:

risk of an incorrect electrical con-

tact.

2

When they need to be re-

placed, be sure to use

the same or equivalent

type of battery (consult an

Approved Dealer).

When refitting, proceed in the reverse

order, then press one of the buttons on

the card four times, close to the vehicle:

the next time the vehicle is started, the

message will disappear.

Replacing the battery

When the message “Keycard Battery

Low” appears on the instrument panel,

replace the battery in the card:

– slide the rear casing 1 downwards

while pressing on zone A;

Check that the cover is clipped shut.

– remove the battery cover 2;

– remove the battery by pressing on

one side and lifting the other;

– replace it according to the direc-

tion and template shown inside the

cover.

Note: Do not touch the electronic circuit

or contacts on the card when replacing

the battery.

When replacing:

– make sure that the batter-

ies are correctly inserted.

Risk of explosion.

– if the flap does not close cor-

rectly, do not use and keep out of

reach of children.

5.22

CARD: battery (2/2)

Operating faults

If the battery is too weak to ensure cor-

rect operation, you will still be able to

start and lock/unlock the vehicle

➥ 1.14.

Precautions relating to

batteries:

– keep (new or used) bat-

teries out of reach of chil-

dren;

– do not swallow batteries;

Risk of chemical burns which

may lead to death.

– if ingested or inserted into any

part of the body, consult a doctor

as soon as possible.

Do not throw away your used bat-

teries; give them to an organisation

responsible for collecting and recy-

cling batteries.

5.23

BATTERY: troubleshooting (1/3)

To avoid all risk of sparks:

Connecting a battery charger

– Ensure that any power consumers

(courtesy lights, etc.) are switched

off before disconnecting or recon-

necting a battery;

The battery charger must be com-

patible with a battery with nominal

voltage of 12 volts.

Do not disconnect the battery when the

engine is running. Follow the instruc-

tions given by the manufacturer of

the battery charger you are using.

– when charging, stop the charger

before connecting or disconnecting

the battery;

– do not place metal objects on the

battery as this could create a short

circuit between the terminals;

Handle the battery with care

as it contains sulphuric acid,

which must not come into

contact with eyes or skin. If

it does, wash the affected area with

plenty of cold water. If necessary,

consult a doctor.

– always wait at least five minutes

after the engine has been switched

off before disconnecting a battery;

– make sure that you reconnect the

battery terminals after refitting.

Keep naked flames, red hot objects

and sparks away from the battery

components as there is a risk of

explosion.

Special procedures may be

required to charge some

batteries. Contact your ap-

proved dealer.

Please note when working close to

the engine that it may be hot. In ad-

dition, the engine cooling fan may

start at any moment. The

warning light in the engine compart-

ment reminds you of this.



Avoid all risk of sparks which may

cause an immediate explosion, and

charge the battery in a well venti-

lated area.

Risk of injury.

Before carrying out any

action in the engine com-

partment, you must switch

off the ignition. ➥ 2.4

➥ 2.6.

Risk of serious injury.

5.24

BATTERY: troubleshooting (2/3)

Starting the vehicle using the

battery from another vehicle

If you have to use the battery from an-

other vehicle to start, obtain suitable

jump leads (with a large cross section)

from an approved dealer or, if you al-

ready have jump leads, ensure that

they are in perfect condition.

2

1

3

The two batteries must have an iden-

tical nominal voltage of 12 volts. The

battery supplying the current should

have a capacity (amp-hours, Ah) which

is at least the same as that of the dis-

charged battery.

Ensure that there is no risk of contact

between the two vehicles (risk of short

circuiting when the positive terminals

are connected) and that the discharged

battery is properly connected. Switch

off your vehicle ignition.

Battery in engine compartment

The battery is not directly accessible.

Use the terminal 1 (+) and the termi-

nal 2 (–) in the engine compartment.

Raise the cover 3 of the terminal 1 (+).

5.25

BATTERY: troubleshooting (3/3)

Start the engine of the vehicle supply-

ing the current and run it at an interme-

diate engine speed.

2

1

If your vehicle’s engine does not start

immediately, switch off the ignition and

wait a few seconds before repeating

the operation.

B

With the engine running, disconnect

the A and B cables in the reverse order

(2 - 4 - 5 - 1).

A

Reposition the cover 3 of the terminal 1

(+).

5

4

Attach the positive cable A to the ter-

minal 1 (+) then to the terminal 5 (+) of

the battery supplying the current.

Connect the negative cable B to the

terminal 4 (–) of the battery supplying

the current and then to the terminal 2

(–).

Check that there is no con-

tact between leads A and B

and that the positive lead A

is not touching any metal

parts on the vehicle supplying the

current.

Risk of injury and/or damage to

the vehicle.

5.26

FITTING A RADIO

1

– In all cases, it is very important to

follow the manufacturer’s instruc-

tions carefully.

2

– The specifications of the brack-

ets and wires (available from our

network) vary depending on the

equipment level of your vehicle

and the type of radio.

Radio location 1

Unclip the blanking cover. The aerial, +

and – supply and speaker wire connec-

tions are located behind it.

Front door speakers 2

To install any equipment, please con-

sult an authorised dealer.

Consult an approved Dealer to

find out the correct part number.

– No work may be carried out on

the vehicle’s electrical or radio

circuits, except by approved

dealers: an incorrectly connected

system may result in damage

being caused to the electrical

equipment and/or the compo-

nents connected to it.

5.27

ACCESSORIES

Electrical and electronic accessories

Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po-

sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer.

Before connecting an accessory to a socket, please ensure that you do not exceed the maximum power authorised for

the socket. ➥ 3.32, ➥ 3.18. Fire hazard.

No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected

system may result in damage being caused to the electrical equipment and/or the components connected to it.

If the vehicle is fitted with any aftermarket electrical equipment, make sure that the installation is correctly protected by a fuse.

Establish the rating and position of this fuse.

Using the diagnostic socket

The use of electronic accessories on the diagnostic socket may cause serious disturbance to the vehicle’s electronic systems.

For your safety we recommend that you use only electronic accessories approved by the manufacturer, consult an Approved

Dealer. Serious accident risk.

Use of transmitting/receiving devices (telephones, CB equipment etc.).

Telephones and CB equipment with integrated aerials may cause interference to the electronic systems originally fitted to the

vehicle: it is advisable only to use equipment with an external aerial. Furthermore, we remind you of the need to conform

to the legislation in force concerning the use of such equipment.

Fitting aftermarket accessories

If you wish to install accessories on the vehicle: please contact an authorised dealer. Also, to ensure the correct operation of

your vehicle, and to avoid any risk to your safety, we recommend that you use only accessories specifically designed for your

vehicle, which are the only accessories for which the manufacturer will provide a warranty.

If you are using an anti-theft device, only attach it to the brake pedal.

Obstructions to the driver

On the driver’s side, only use mats suitable for the vehicle, attached with the pre-fitted components, and check the fitting regu-

larly. Do not lay one mat on top of another. There is a risk of wedging the pedals.

5.28

FUSES (1/4)

1

2

A

B

3

C

Passenger compartment fuses B

Unclip the access flap 2.

Fuses located in the passenger

compartment behind a flap in the C

glovebox

Fuse boxes

If any electrical component does not

work, check the condition of the fuses.

Open and tilt the 2 flap completely then

pull it downwards to move it in order to

access the fuses.

Unclip the access flap 3.

Passenger compartment fuses A

Unclip the access flap 1.

Check the fuse in question and replace it, if necessary, by a fuse of the

same rating.

To comply with current legislation, or

as a precaution, you can obtain an

emergency kit from your approved

dealer containing a set of spare

bulbs and fuses.

If a fuse is fitted with too high a rating, it may cause the electrical circuit

to overheat (risk of fire) in the event of an item of equipment using an ex-

cessive amount of current.

5.29

FUSES (2/4)

4

To comply with current legislation, or

as a precaution, you can obtain an

emergency kit from your approved

dealer containing a set of spare

bulbs and fuses.

Tweezers 4

Remove the fuse using the tweezers 4

on the back of the flap.

To remove the fuse from the tweezers,

slide the fuse to the side.

It is not advisable to use the free fuse

locations.

Check the fuse in question

and replace it, if neces-

sary, by a fuse of the same

rating.

If a fuse is fitted with too high a

rating, it may cause the electrical

circuit to overheat (risk of fire) in the

event of an item of equipment using

an excessive amount of current.

5.30

FUSES (3/4)

Allocation of fuses

(the presence of certain fuse depends on the vehicle equipment level)

Symbol

Allocation

Windscreen washer

H

Multimedia accessories socket, multimedia

screen

î

Æ

Front and rear second row accessories socket

Horn

Ì

Towbar socket

Ý



Heated rear view mirrors

Use the fuse allocation label in the

storage compartment to identify the

fuses.

Brake lights, passenger compartment central unit

×

Passenger compartment centre unit, rear wiper,

rear fog light

Certain fuses should only be re-

placed by a qualified professional.

These fuses are not listed on the

label.



D

Direction indicator lights, hazard warning lights,

high level brake lights

Only change the fuses represented

on the label.

5.31

FUSES (4/4)

5

D

Fuses in engine compartment D

Please note when work-

ing close to the engine that

it may be hot. In addition,

LPG fuse in the front

compartment

5 fuse: LPG circuit shut-off.

Some functions are protected by fuses

located in the engine compartment

(unit D).

start at any moment. The

^{the engine cooling
fa}^{n may}

warning light in the engine compart-

ment reminds you of this.

However, because of their reduced

accessibility, we advise you to have

your fuses replaced by an approved

Dealer.

Risk of injury.

Before carrying out any

action in the engine com-

partment, you must switch

off the ignition. ➥ 2.4 or

➥ 2.6.

5.32

WIPER BLADES: replacement (1/2)

A

B

1

2

3

4

Replacing the windscreen

To refit

wiper blades 2

To refit the wiper blade 2, insert it in its

housing in the arm 3, then clip it until

you hear a click. Make sure that the

blade is correctly locked in position.

To replace the wipers, first put them in

the service positionB.

With the engine running or the igni-

tion on:

To return the blades to lowered posi-

tion, make sure that the blades are

folded down onto the windscreen then

set the 1 stalk to position A (single

sweep): the windscreen wiper blades

will fold into the bonnet when the igni-

tion is switched on.

Check the condition of the wiper

blades. You are responsible for their

service life:

– clean the blades, windscreen and

rear screen regularly with soapy

water;

– do not use them when the wind-

screen or rear screen are dry;

– free them from the windscreen or

rear screen when they have not

been used for a long time.

– set the stalk 1 to position A twice in

succession (single sweep): the wiper

blades will stop in position B away

from the bonnet;

– lift the wiper arm 3;

– lower the 4 tab then remove the

blade 2.

5.33

WIPER BLADES: replacement (2/2)

To refit

To refit the wiper blade, proceed in re-

verse order to removal. Make sure that

the blade is correctly locked in position.

5

B

– In frosty weather, make

sure that the wiper blades

are not stuck by ice (to

avoid the risk of the motor

6

overheating).

– Check the condition of the wiper

blades. Replace the wiper blades

as soon as they begin to lose ef-

ficiency (approximately once a

year).

Rear screen wiper blade 5

Stalk in stop position (deactivated):

– lift the wiper arm 6;

– turn the blade horizontally 5 (move-

ment B) until it unclips;

– remove the blade by pulling it.

When changing the blade, when it

has been removed, do not let the

wiper arm fall against the window:

risk of breaking the window.

Check the condition of the wiper

blades.

– clean the blades, windscreen and

rear screen regularly with soapy

water;

– do not use them when the wind-

screen or rear screen are dry;

Before changing the rear

wiper blade, make sure the

stalk is in the stop position

(deactivated).

– free them from the windscreen or

rear screen when they have not

been used for a long time.

Risk of injury.

5.34

TOWING: breakdown recovery (1/2)

Before carrying out any towing, posi-

tion the gearbox in neutral position (po-

sition N on vehicles equipped with an

automatic gearbox), unlock the steering

column then release the parking brake.

The speed specified by current legis-

lation for towing must always be ob-

served. If you are driving the towing

vehicle, do not exceed the permissible

towing weight for your vehicle. ➥ 6.9.

1

2

Steering column unlocking

Towing a vehicle with an

automatic gearbox

Transport the vehicle on a trailer or tow

it with the front wheels off the ground.

Insert the key into the ignition, set to ON

2 position or, depending on the vehicle,

with the card in the passenger compart-

ment, press the engine start button for

approximately two seconds.

In exceptional circumstances, you

may tow it with all four wheels on the

ground, only in a forward gear, with the

gear lever in neutral position N over a

maximum distance of 50 miles (80 km)

and at a maximum speed of 16 mph

(25 km/h).

Reposition the lever to neutral (position

N for vehicles fitted with an automatic

gearbox).

When setting off, if the lever is locked in

position P even though you are press-

ing the brake pedal, the lever can be re-

leased manually in order to unlock the

drive wheels.

The steering column unlocks and the

accessory functions are powered: you

can use the vehicle’s lights (direction

indicators, brake lights etc.). At night

the vehicle must have its lights on.

To do this, unclip the base of the gaiter

and press the 2 push button while si-

multaneously pressing the 1 button on

the lever to unlock the lever and shift to

position N.

Depending on the vehicle, once you

have finished towing, press the engine

start button twice (risk of running down

the battery).

Ensure that the towing eye

is bolted correctly.

Risk of losing the towed

object.

Contact an authorised dealer as soon

as possible.

Leave the card in the vehi-

cle during towing.

Risk of the steering

column locking.

5.35

TOWING: breakdown recovery (2/2)

Tighten the towing hitch 5 fully: first

by hand until it stops, then finish by

locking it with the wheel brace or, de-

pending on the vehicle, the lever.

6

A

Only use the towing hitch 5 and the

wheelbrace or lever provided with the

tools. ➥ 5.7.

4

C

B

D

7

3

– Use a rigid towing bar.

If a rope or cable is used

(where the law allows this),

the vehicle being towed

must be able to brake.

5

Only use the front 3 and rear 7 towing

points (never use the driveshafts or any

other part of the vehicle). These towing

points may only be used for pulling.

They must never be used for lifting the

vehicle directly or indirectly.

Access to towing points

– A vehicle must not be towed if it is

not fit to be driven.

– Avoid accelerating or braking

suddenly when towing, as this

may result in damage being

caused to the vehicle.

Front towing point

Press zone A and keep depressed

while pulling zone B to open flap 4.

Rear towing point

Press zone C and keep depressed

while pulling zone D to open flap 6.

– In all cases, it is advisable not to

exceed 15.5 mph (25 km/h).

When the engine is

stopped, steering and brak-

ing assistance are not oper-

ational.

Ensure that the towing eye

is bolted correctly.

Do not leave the tools unse-

cured inside the vehicle as

they may come loose under

braking.

Risk of losing the towed

object.

5.36

OPERATING FAULTS (1/7)

Using the card

POSSIBLE CAUSES

WHAT TO DO

The card does not lock or unlock the

doors.

Card battery is flat.

Replace the battery. You will still be able to

lock/unlock and start your vehicle. ➥ 1.14

and ➥ 2.3 or ➥ 2.6.

Use of appliances operating on the

same frequency as the card (mobile

phone, etc.).

Stop using the devices or use the key pro-

vided. ➥ 1.14.

Vehicle located in a high electromag-

netic radiation zone.

Use the key that is built into the card

➥ 1.14.

Vehicle battery flat.

The message “Place card on zone +

START” appears on the instrument

panel.

Place the card in the placement area

➥ 2.6 then press the START button.

The vehicle is started.

With the engine running, the card’s locking/

unlocking device is blocked. Turn off the ig-

nition.

Desynchronisation of the card

Unlock the driver’s door by inserting the

key integrated in the card into the door lock

➥ 1.14 then place the card in the placement

area ➥ 2.6 and press the START button to

synchronise the card.

5.37

OPERATING FAULTS (2/7)

The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact

an approved dealer as soon as possible.

Using the remote control

POSSIBLE CAUSES

ACTION REQUIRED

The remote control does not lock or The remote control battery is flat.

unlock the doors.

Use the emergency key.

Use of appliances operating on the same Stop using the devices or use the key.

frequency as the remote control (mobile

phone, etc.).

Vehicle located in a high electromagnetic Replace the battery. You will still be able to

radiation zone.

Discharged battery.

lock/unlock and start your vehicle. ➥ 1.14

and ➥ 2.3 or ➥ 2.6.

The vehicle is started.

With the engine running, the key’s locking/

unlocking device is blocked. Turn off the

ignition.

Desynchronisation of the remote control

Unlock the driver’s door by inserting the

key into the door lock ➥ 1.14, then start the

engine to synchronise the remote control

➥ 2.4 or ➥ 2.6.

5.38

OPERATING FAULTS (3/7)

The starter is activated

POSSIBLE CAUSES

ACTION REQUIRED

The instrument panel indicator lights are Battery terminals not tight, bat- Retighten or reconnect the terminals, or clean them if

weak or fail to light up and the starter tery terminals disconnected or they are oxidised.

does not turn.

oxidised.

Discharged battery or not op-

erational.

Connect another battery to the faulty battery. ➥ 5.24 or

replace the battery if necessary.

Do not push the vehicle if the steering column is

locked.

Faulty circuit.

Consult an approved dealer.

The engine will not start.

Starting conditions are not ful-

filled.

➥ 2.3 or ➥ 2.6.

The card does not work.

Place the card in the recess provided for this purpose

on the centre console.

➥ 2.3 or ➥ 2.6.

With the vehicle stationary, engine cold, Petrol version, this is not nec- The engine’s idle speed should decrease after about

the engine’s idle speed is high.

essarily a fault. This may be one minute. Otherwise, this may be caused by an-

caused by the increase in the other fault. Call an approved Dealer.

engine temperature.

The engine cannot be switched off.

Card not detected.

Place the card in the recess provided for this purpose

on the centre console.

Press and hold the start button.

Electronic fault.

Press the start button 3 times quickly or press and

hold.

The steering column remains locked.

Steering wheel locked.

Move the steering wheel while pressing the engine

start button (or, depending on the vehicle, operating

the ignition key) ➥ 2.3.

Faulty electrical circuit.

Consult an approved dealer.

5.39

OPERATING FAULTS (4/7)

On the road

POSSIBLE CAUSES

WHAT TO DO

Vibrations.

Tyres not inflated to correct pres-

sures, incorrectly balanced or dam-

aged.

Check the tyre pressures: if this is not the

problem, have them checked by an ap-

proved Dealer.

White smoke from the exhaust.

In the diesel version, this is not neces-

sarily a fault. Smoke may be caused

by particle filter regeneration.

➥ 2.16.

Petrol version, this is not necessarily

a fault. Depending on the climate con-

ditions (cold, humidity etc.), smoke

may be produced under hard vehicle

acceleration.

Reduce the engine speed and avoid

sudden acceleration to gradually make the

smoke disappear. Otherwise, this may be

caused by another fault. Consult an ap-

proved dealer.

Smoke under the bonnet.

Short-circuit or cooling system leak.

Stop, switch off the ignition, stand away

from the vehicle and contact an approved

dealer.

The oil pressure warning light comes

on:

while cornering or braking

The level is too low.

Loss of oil pressure.

Top up the engine oil ➥ 4.5.

is slow to go out or remains lit

under acceleration

Stop the vehicle and contact an approved

Dealer.

5.40

OPERATING FAULTS (5/7)

On the road

POSSIBLE CAUSES

WHAT TO DO

Steering becomes heavy.

Assistance overheating.

Drive carefully at reduced speed, be aware

of the level of force in the steering wheel

needed to turn the wheels.

Fault with the electric assistance

motor.

Consult an authorised dealer.

Fault in the assistance system

The engine is overheating. The

coolant temperature indicator is in

the warning zone and warning light

® comes on.

Engine cooling fan not working.

Stop the vehicle, switch off the engine and

contact an approved dealer.

Coolant leaks.

Check the coolant reservoir: it should con-

tain fluid. If there is no coolant, consult an

authorised dealer as soon as possible.

Coolant boiling in the coolant reser-

voir.

Mechanical fault: damaged cylinder

head gasket.

Stop the engine.

Contact an approved dealer.

Radiator: In the event of a significant lack of coolant, remember that you must never top up using cold coolant while

the engine is very hot. After any procedure on the vehicle which has involved even partial draining of the cooling

system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved

by our Technical Department may be used for this purpose.

5.41

OPERATING FAULTS (6/7)

Electrical equipment

POSSIBLE CAUSES

WHAT TO DO

The wipers do not work.

Wiper blades stuck.

Free the blades before using the wipers.

Faulty electrical circuit.

Fuse damaged.

Consult an approved dealer.

Replace the fuse or have it replaced

➥ 5.29.

The wiper does not stop.

Faulty electrical controls.

Blown rear bulb.

Consult an approved dealer.

Direction indicators flashing more

quickly.

➥ 5.15

The direction indicators do not work.

The lights do not come on or go off.

Faulty electrical circuit or control.

Fuse damaged.

Consult an approved dealer.

Replace the fuse or have it replaced

➥ 5.29.

Faulty electrical circuit or control.

Fuse damaged.

Consult an approved dealer.

Replace the fuse or have it replaced

➥ 5.29.

5.42

OPERATING FAULTS (7/7)

Electrical equipment

POSSIBLE CAUSES

WHAT TO DO

Traces of condensation in the head-

lights or rear lights.

Traces of condensation may be a nat-

ural phenomenon caused by varia-

tions in temperature and humidity.

In this case, the traces will disappear

slowly once the lights are switched

on.

The front seat belt reminder light

comes on when the seat belts are

fastened.

An object is stuck between the floor

and the seat and is disrupting the op-

eration of the sensor.

Remove all objects from underneath the

front seats.

5.43

5.44

Practical Advice for Your Renault Clio 4 Door Fifth Generation (2019-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals