Get Your comfort Guide for Renault Zoe 4 Door Third Generation (2019-2024)

Section 3: your comfort

Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manual air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2

3.4

3.7

Air conditioning: programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11

Air conditioning: information and advice on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13

Multimedia equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.15

Electric windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16

Interior lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.18

Sun visor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.18

Passenger compartment storage, fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.19

Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.22

Accessories socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.22

Rear bench seat: functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.24

Rear parcel shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.25

Luggage cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.26

Luggage compartment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.27

Spoiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.27

Transporting objects in the luggage compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.28

3.1

AIR VENTS: air outlets (1/2)

3

4

2

1

2

1

5

6

5

1 side air vent.

4 centre air vents.

2 side demister outlet.

3 windscreen demisting vents.

5 passenger footwell heater outlets.

6 control panel.

3.2

AIR VENTS: air outlets (2/2)

To remove bad odours from your ve-

hicles, only use the systems designed

for this purpose. Consult an approved

Dealer.

7

1

4

Centre air vents.

Side air vents

Direction

Air flow

Move cursors 4 to the required position.

To open air vent 1, press on the air vent

(point 7) until it is open as far as re-

quired.

Direction

To direct the air flow, swivel side air

vent 1.

Do not add anything to the

vehicle’s ventilation circuit

(for example, to remove

bad odours).

There is a risk of damage or of

fire.

3.3

MANUAL AIR CONDITIONING (1/3)

The air conditioning system is used

for:

4

5

1

2

3

– lowering the temperature inside the

passenger compartment;

– eliminating condensation more

quickly.

Advice: to optimize vehicle range, de-

activate the air conditioning when the

outside temperature is comfortable.

Adjusting the ventilation

speed

Turn the control 3 to one of the eight

positions to start the ventilation system

and adjust the power.

6

7

The controls

Switching air conditioning on

or off

1 Adjusting the air temperature.

Position OFF

In this position:

– the air conditioning switches off au-

tomatically;

– the ventilation speed of air in the

passenger compartment is zero;

– there is, however, a slight flow of air

when the vehicle is moving.

This position should not normally be

used.

(depending on vehicle)

2 “Clear View” function.

The air conditioning is switched on (in-

dicator light on) or off (indicator light off)

using button 4.

3 Push button to adjust fan speed and

stop the system.

4 Air-conditioning activation control.

5 Passenger compartment air distribu-

tion adjustment.

The system cannot be switched on if

the control 3 is set to OFF.

6 Air recirculation.

7 De-icing/demisting of the rear screen

and, depending on the vehicle, the

door mirrors.

Heating or air-conditioning can only be

used while the engine is running.

Some buttons have an operating

tell-tale which indicates the operat-

ing status.

3.4

MANUAL AIR CONDITIONING (2/3)

The air flow is directed towards

the dashboard vents and to-

wards the footwells.

5

ö

1

3

The air flow is mainly directed

to the dashboard air vents.

ô

ó

The air flow is directed mainly

towards the footwells.

Rear screen de-icing/

demisting

Press the 7 button: the integrated indi-

cator light comes on. This function ena-

bles rapid demisting/de-icing of the rear

screen and the rear view mirrors (on

equipped vehicles).

7

Adjusting the air temperature

Adjusting the distribution

of air in the passenger

compartment

Turn control 5 to choose the distribution

option.

To exit this function, press button 7

again. Demisting automatically stops.

Turn the control 1 to one of the eight

positions to set the temperature. The

further towards the red the slide is, the

higher the temperature will be.

When the air conditioning system is

used for long periods, it may begin to

feel cold. To increase the temperature,

turn control 1 to the right.

All the air is then directed to

the windscreen and front side

window demisting vents.

W

The air flow is distributed be-

tween front side window de-

misting vents, the windscreen demist-

ing vents and the footwells.



Recommendations

In the event of freezing, manu-

ally de-ice the windscreen using a

scraper rather than the de-icing/de-

misting function in order to reduce

your energy consumption.

3.5

MANUAL AIR CONDITIONING (3/3)

Air recirculation is for:

2

3

– isolating the vehicle from the exter-

nal atmosphere (driving in polluted

areas, etc.);

– lowering the passenger compart-

ment temperature as quickly as pos-

sible.

Stopping the system

Press button 3.

6

Clear View function

Press the 2 button: the integrated indi-

Switching the air

recirculation on

cator light comes on.

Press button 6: the integrated indicator

light comes on. In these conditions, air

is taken from the passenger compart-

ment and is recycled, with no air being

taken from outside the vehicle.

This system quickly demists and de-

ices the windscreen and the front side

windows. It requires the automatic

usage of the air-conditioning or the

heating.

Prolonged use of air recirculation

can lead to condensation forming on

the side windows and windscreen,

and discomfort due to the use of

non-renewed air in the passenger

compartment. We therefore advise

you to return to normal mode (exter-

nal air) as soon as the air recircula-

tion function is no longer required,

by pressing the button 6 again.

To exit this function, select the adjust-

ment required (distribution, ventilation

speed, temperature, air recirculation).

The demisting/de-icing will still take

priority over the air recirculation.

3.6

AUTOMATIC CLIMATE CONTROL (1/4)

Adjusting the ventilation

speed.

2

3

1

4

5

6

In automatic mode, the system uses

the most suitable amount of air to reach

and maintain the desired comfort level.

You can still adjust the ventilation

speed by turning control 1 to increase

or reduce the ventilation speed.

Adjusting the air temperature

Turn control 3 to obtain the desired

temperature.

7

Automatic mode

8

Turning the control to the right in-

creases the temperature.

The controls

(depending on the vehicle)

Note: to increase the vehicle range,

reduce the comfort level by turning

the 3 control

The automatic climate control system

guarantees comfort in the passen-

ger compartment and good visibility

(except in the event of extreme condi-

tions), while optimising fuel consump-

tion. The system controls the ventilation

speed, air distribution, air recirculation,

and starting and stopping the air condi-

tioning and air temperature.

1 Adjusting the ventilation speed and

OFF position.

2 “Clear View” function.

3 Adjusting the air temperature.

4 Automatic mode.

5 Air conditioning control.

AUTO: allows the selected comfort

level to be best attained, depending on

the exterior conditions. Press button 4.

6 Distribution of air in the passenger

compartment.

7 Air recirculation.

8 De-icing/demisting of the rear screen

and, depending on the vehicle, the

rear view mirrors.

Any action on a button other than

the AUTO button triggers deactiva-

tion of automatic mode.

3.7

AUTOMATIC CLIMATE CONTROL (2/4)

Clear View function

4

6

2

Press the 2 button: the integrated indi-

cator light comes on.

This function quickly de-mists the wind-

screen, rear screen, front side windows

and door mirrors (depending on the

vehicle). The air conditioning and rear

screen de-icing functions must be ac-

tivated.

Press button 8 to stop the heated rear

screen operating, and the integrated in-

dicator goes out.

To exit this function, press button 2

or 4.

8

The air flow is directed towards

the dashboard vents and to-

wards the footwells.

Adjusting the distribution

of air in the passenger

compartment

Turn control 6. The integrated warning

light in the button comes on.

ö

The air flow is mainly directed

to the dashboard air vents.

ô

ó

The air flow is directed mainly

towards the footwells.

All the air is then directed to

the windscreen and front side

window demisting vents.

W

The air flow is distributed be-

tween front side window de-

misting vents, the windscreen demist-

ing vents and the footwells.



Some buttons have an operating

tell-tale which indicates the operat-

ing status.

3.8

AUTOMATIC CLIMATE CONTROL (3/4)

5

8

Rear screen de-icing/

demisting

Switching air conditioning on

or off

Press the 8 button: the integrated in-

dicator light comes on. This function

enables rapid demisting or de-icing of

the rear screen and de-icing of the rear

view mirrors (on equipped vehicles).

In automatic mode, the system switches

the air conditioning system on or off,

depending on the climate conditions.

Press the button 5 to force the air con-

ditioning to stop. The integrated warn-

ing light will go out.

To exit this function, press button 8

again. Demisting automatically stops.

3.9

AUTOMATIC CLIMATE CONTROL (4/4)

Stopping the system

1

4

Turn the control 1 to “OFF” to stop the

system. To start it, turn the control 1

again, then adjust the fan speed or

press the button 4.

7

Manual use

Air recirculation (isolation of

the passenger compartment)

This function is managed automatically

(operation is confirmed by a warning

light on button 7), but you can also acti-

vate it manually.

Press the 7 button: the integrated indi-

cator light comes on.

Prolonged use of this position may lead

to odours, caused by non-renewal of

air, and the formation of condensation

on the windows.

We therefore advise you to return to au-

tomatic mode as soon as air recircula-

tion is no longer needed, by pressing

button 7.

The demisting/de-icing will still take

priority over the air recirculation.

3.10

AIR CONDITIONING: programming (1/2)

1

2

5

EV programming

Comfort programs

OFF

Temperature

Program

Edit

Comfort programme 1

06:00 AM

3

L M M J V S D

Ready to

L M M J V S D

Comfort programme 2

Ready to 09:00 AM

A

6

Charge

Climate

Calendar

4

With the engine running and the ve-

hicle stationary, use the multimedia

screen 1 to select the “Settings” menu

and the “Vehicle” tab, then select the

“EV programming” menu 2 and the

“Climate” tab 4.

On vehicles fitted with an automatic air

conditioning system, you can adjust the

temperature 5 from this menu and acti-

vate/deactivate saved programmes.

Select the time and date 6 for the

schedule that you wish to change to

access the settings.

Driver’s responsibility

when parking or stopping

the vehicle

Never leave an animal,

child or adult who is not self-suffi-

cient alone on your vehicle, even for

a short time.

Programmed times are displayed in

area A.

Programming the departure

time

Press “Edit” 3 to access the comfort

In hot and/or sunny weather, please

remember that the temperature

inside the passenger compartment

increases very quickly.

Note: you can program the air condi-

tioning using a smartphone application.

Please refer to the multimedia instruc-

tions for further information.

settings.

You may store multiple comfort pro-

grams.

RISK OF DEATH OR SERIOUS

INJURY.

3.11

AIR CONDITIONING: programming (2/2)

Note:

However, the function can be deacti-

vated if:

– the engine is running;

– the charging socket is disconnected;

– the traction battery charging level is

lower than 20%;

Immediate activation of the

air-conditioning

It is possible to carry out immediate

starting of the air conditioning, if:

– the bonnet is closed;

– the traction battery charge level is

over 20%;

– You can deactivate the comfort pro-

grams by pressing “OFF”;

– the minimum time period between

each programme is two hours;

– depending on the vehicle, the se-

lected temperature is displayed on

the 2 menu.

– the bonnet is open.

Note: any modification carried out

within 2 hours before a programmed

start must be cancelled and re-pro-

grammed in order to be registered.

– the doors are closed and locked;

– the engine is stopped.

“Programme” activation

The function launches before the time

scheduled by the customer, so that the

vehicle reaches a comfortable temper-

ature by the time they arrive, if:

– the vehicle is connected to the elec-

trical supply;

With the engine running and the ve-

hicle stationary, use the multimedia

screen 1 to select the “Settings” menu,

“Vehicle” tab, then the “EV program-

ming” menu and the “Climate” tab 4.

Please refer to the multimedia instruc-

tions for further information.

– the bonnet is closed;

– the traction battery charge level is

over 20%;

– the doors are closed and locked;

Driver’s responsibility

when parking or stopping

the vehicle

Stopping the programmed air

conditioning

The air conditioning stops automati-

cally around ten minutes after the set

end time.

^{– the engine i}^{s stopped.}

comes on the in-

Never leave an animal,

child or adult who is not self-suffi-

cient alone on your vehicle, even for

a short time.

Warning light

strument panel.

Note: if your vehicle is not connected,

your programme is reduced to 10 min-

utes in order to maintain vehicle range.

In hot and/or sunny weather, please

remember that the temperature

inside the passenger compartment

increases very quickly.

RISK OF DEATH OR SERIOUS

INJURY.

3.12

AIR CONDITIONING: information and operating instructions (1/2)

Recommendations to limit energy

consumption and maintain the

vehicle range

Advice on use

Operating faults

As a general rule, contact your ap-

proved dealer in the event of an oper-

ating fault.

In some situations, (air conditioning

off, air recirculation activated, ventila-

tion speed at zero or low, etc.) you may

notice that condensation starts to form

on the windows and windscreen.

Drive with the air vents open and the

windows closed. If the vehicle has been

parked in the sun, open the doors for a

few moments to let the hot air escape

before starting the engine.

– Reduction in de-icing, demisting

or air conditioning performance.

This may be caused by the passen-

ger compartment filter cartridge be-

coming clogged.

If there is condensation, use the “Clear

View” function to remove it, then use

the air conditioning in automatic mode

to stop it forming again.

It is preferable, before setting off, to

use of the programmed air conditioning

➥ 3.11.

– No hot or cold air is being pro-

duced. Check that the controls are

set correctly and that the fuses are

sound. Otherwise, switch off the

system.

Maintenance

Refer to the Maintenance Document

for your vehicle for the inspection fre-

quency.

Presence of water under the

vehicle

After prolonged use of the air condi-

tioning system, it is normal for water

to be present under the vehicle. This is

caused by condensation.

Range

It is normal to notice an increase in

energy usage when the air conditioning

is operating.

Do not open the refriger-

ant fluid circuit. The fluid

may damage eyes or skin.

Use the air conditioning system reg-

ularly, even in cold weather, running

it at least once a month for approxi-

mately 5 minutes.

3.13

AIR CONDITIONING: information and operating instructions (2/2)

Type of refrigerant fluid

Ñ









A

Type of oil in the air condi-

tioning circuit

Inflammable product

Consult the driver’s hand-

book

Maintenance

Quantity of refrigerant

fluid present in the ve-

hicle.

x.xxx kg

The refrigerant fluid circuit (of which

some components are hermetically

sealed) may contain fluorinated green-

house gases.

Global

Potential (CO2 equiv-

alent).

Warming

GWP xxxxx

Do not open the refrigerant

fluid circuit. The fluid may

damage eyes or skin.

Depending on the vehicle, you will find

the following information on label A af-

fixed inside the engine compartment.

CO2 eq Quantity in weight and

x.xx t in CO2 equivalent.

The presence and location of the infor-

mation on label A depends on the ve-

hicle.

Before carrying out any

action in the engine com-

partment, you must switch

off the ignition. ➥ 2.2.

3.14

MULTIMEDIA EQUIPMENT

1

2

3

4

6

2

3

5

The presence and location of this equip-

ment depends on the vehicle version.

Induction charging area 5

➥ 3.19

1 Multimedia touchscreen display;

2 Multimedia sockets;

3 Steering column control;

4 Voice commands;

5 Induction charging area;

6 Microphone.

Using the telephone

We remind you of the need

to conform to the legislation

in force concerning the use

of such equipment.

Refer to the equipment instructions

for information on how to operate

this equipment.

3.15

ELECTRIC WINDOWS (1/2)

Electric windows

Press or pull the switch to raise or lower

a window to the desired height (the rear

windows do not open fully);

These systems operate with the igni-

tion on or off, until one of the front doors

is opened (limited to about 3 minutes).

1

3

5

2

4

6

From the driver’s seat, use switch:

1 for the driver’s side;

2 for the front passenger side;

3 and 5 for the rear passenger win-

dows.

From the passenger seats, use

switch 6.

Note: if the window detects resistance

when closing (e.g.: branch of a tree,

etc.) it stops and then lowers again by a

few centimetres.

Safety of rear occupants

The driver can prevent operation of the rear electric windows by pressing

switch 4. A confirmation message is displayed on the instrument panel.

Driver’s responsibility

Never leave your vehicle with the card inside, when there is a child, dependent

adult or a pet on-board, even for a short while. They may pose a risk to them-

selves or to others by starting the engine or activating equipment (such as the

gear lever or electric windows). If any part of the body becomes trapped, reverse

the direction of the window immediately by pressing the relevant switch.

Risk of serious injury.

Avoid resting any objects against

a half-open window: there is a risk

that the electric window could be

damaged.

3.16

ELECTRIC WINDOWS (2/2)

One-touch mode

(depending on vehicle)

Operating faults

If a fault occurs when closing a window,

the system switches to normal mode:

lift the switch concerned as many times

as necessary until the window is fully

closed, release it. Press the switch

again (still on the closing side) for ap-

proximately one second to reset the

system.

This mode works in addition to the

operation of the electric windows de-

scribed previously. It can be fitted to the

driver’s window.

Briefly press or pull the window switch

fully: the window is fully lowered or

raised. Pressing the switch again stops

the window moving.

8

If necessary, contact an approved

Dealer.

Impossible to operate the one-touch

electric window

The one-touch electric window is

equipped with heat protection: if you

press the switch for the window more

than sixteen consecutive times it goes

into protection mode (locking the

window).

Manual window winder

controls

Turn handle 8.

You can:

– use the electric window switch briefly

and with intervals of approximately

30 seconds;

– with the engine running, the window

will be unlocked after approximately

20 minutes of inaction on the electric

window switch.

When closing the windows,

ensure that no part of the

body (arm, hand, etc.) is

protruding from the vehicle.

Note: if the window detects resistance

when closing (e.g.: branch of a tree,

etc.) it stops and then lowers again by a

few centimetres.

Risk of serious injury.

3.17

INTERIOR LIGHTING, SUN VISOR

1

2

6

3

4

5

Map reading light

Luggage compartment light

Light 3 comes on when the luggage

compartment is opened.

Sun visor

Lower the sun visor 4 over the wind-

screen or unclip it and turn it over the

side window.

(depending on the vehicle)

Press switch 1 of 2 for:

– permanent lighting;

– lighting switches off immediately.

Courtesy mirrors

Slide cover 5.

Note: on vehicles fitted with a multime-

dia screen, you can use the multime-

dia screen to deactivate/activate the

reading lights which switch on when

the doors or luggage compartment are

opened. ➥ 1.92.

The light 6 switches on automatically.

Unlocking and opening the doors or

tailgate switches on the timed cour-

tesy lights and lights.

3.18

PASSENGER COMPARTMENT STORAGE, FITTINGS (1/3)

3

2

1

4

Front door storage

compartments 1

Induction charging area 2

Central storage

compartment 3

This is used to charge your phone with-

out the need for a cable. Please refer

to the multimedia instructions for further

information.

Cup holder 4

When turning corners,

accelerating or braking,

ensure that the recepta-

cle being held by the cup

No object should be placed

on the floor (in front of the

driver). Such objects may

slide under the pedals

during sudden braking manoeuvres

and obstruct their use.

holder is not dislodged.

There is a risk of burning if hot

liquid escapes.

3.19

PASSENGER COMPARTMENT STORAGE, FITTINGS (2/3)

6

7

5

8

Sun blind storage

compartment 5

Can be used to hold motorway toll tick-

ets, maps, etc.

Central storage

compartment 6

(depending on the vehicle)

Dashboard storage 7

Glove box

Pull handle 8 to open it.

Can be used to hold motorway toll tick-

ets, maps, etc.

It can hold A4 size documents, a large

bottle of water, etc.

Ensure that no hard, heavy

or pointed objects are

placed in the “open” storage

compartments in such a

way that they may fall onto passen-

gers during sudden turning, braking

or in the event of an accident.

3.20

PASSENGER COMPARTMENT STORAGE, FITTINGS (3/3)

11

9

10

Grab handle 9

This offers support and can be held

when the vehicle is being driven.

Rear door storage

compartment 10

Storage pocket 11 with side

opening

Do not use it for getting into or out of

the vehicle.

Ensure that no hard, heavy

or pointed objects are

placed in the “open” storage

compartments in such a

way that they may fall onto passen-

gers during sudden turning, braking

or in the event of an accident.

3.21

ACCESSORIES SOCKET

1

Accessories sockets 1

They are provided for connecting ac-

cessories approved by our Technical

Department.

Connect accessories with

a

maximum power of

120 watts (12 V) only.

When several accessory

sockets are used at the same time,

the total power of the connected

accessories must not exceed

180 watts.

Fire hazard.

3.22

REAR HEADRESTS

A

B

1

Position for use

To refit the headrest

Raise or lower the headrest while pull-

ing it towards the front of the vehi-

cle. Check that the bonnet is correctly

locked.

Insert the headrest rods into the holes,

and lower the headrest to the first

notch. Check that it is correctly locked.

Storage position

Press the button A and lower the head-

To remove the headrest

Press the button A on the switch 1 and

rest completely.

remove the headrest.

When the headrest is set at the

lowest position (position B), this is

for storage only: it should not be in

this position when a seat is occupied.

The headrest is a safety

component; check that it is

fitted and in the correct po-

sition.

3.23

REAR BENCH SEAT: functions

To replace the seatback, proceed in

the reverse order to removal.

Before moving the seatback, put

the seat belt in belt guide A to avoid

damaging it.

Refit the seatback and click it back into

place.

B

1

A

When moving the rear

seats, ensure that nothing

obstructs the anchorage

points (passenger’s arm or

leg, a pet, gravel, cloth, toys, etc.).

The seatback may be folded down to

allow bulky objects to be transported.

To fold down the seatback

Ensure that the front seats are far

enough forward.

For safety reasons, carry

out any adjustments when

the vehicle is not being

driven.

When refitting the seat-

back, make sure it is cor-

rectly locked in place.

Lower the headrests fully.

Place the seat belts in their guides A.

The configuration of the two-seat

bench with the small seatback B

pulled down, does not allow the

central seat to be used as it would

be impossible to buckle the seat belt

(belt buckles inaccessible).

If seat covers are fitted,

make sure these do not prevent the

seatback latch from locking in.

Make sure that the seat belts are

positioned correctly.

Press button 1 and lower the seat-

back B.

Reposition the headrests.

3.24

REAR PARCEL SHELF

1

2

– push the shelf 2 inwards and turn it;

Rear parcel shelf

To remove:

– pull the shelf towards you.

To refit, proceed in the reverse order to

removal.

– lower the rear headrests;

– unhook both straps 1;

– lift the shelf 2 upwards to unclip;

Do not place any objects,

especially heavy or hard

objects, on the parcel shelf.

These may pose a risk to

the vehicle occupants if the driver

has to brake suddenly or if the vehi-

cle is involved in an accident.

Maximum weight on rear parcel

shelf: 2 kg, evenly distributed.

3.25

LUGGAGE COMPARTMENT COVER: utility versions

B

A

The luggage compartment cover con-

sists of a rigid section A and a folding

section B.

The luggage compartment cover is

in the folded position.

The luggage compartment cover is

removed.

To fold it:

To remove it: with the cover in the folded

The luggage cover is in the unfolded

position.

position and holding it horizontally:

– lift shelf A slightly and pull it towards

you to remove it;

– pull one side of the luggage com-

partment cover towards you, tilting it

slightly;

– then fold section B back on itself.

– then pull the other side of the lug-

gage compartment cover to com-

pletely detach it from its housing.

Do not place any objects,

especially heavy or solid

objects on the luggage

compartment cover. These

may pose a risk to the vehicle occu-

pants if the driver has to brake sud-

denly or if the vehicle is involved in

an accident.

3.26

LUGGAGE COMPARTMENT, SPOILER

A

1

Opening

Spoiler

Press button 1 and lift the tailgate.

It is forbidden to attach objects and/

or accessories (bike rack, etc.) to

spoiler A.

Closing

Lower the luggage compartment lid,

depending on the vehicle, initially using

the inside handle to assist you.

3.27

TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT

Always position the objects transported

so that the largest surface is against:

– The rear bench seatback for normal

A

B

loads (example A).

1

– The front seatbacks with the rear

seatbacks folded down, as is the case

for maximum loads (example B).

Always position the heavi-

est items directly on the

floor. Use the lashing

Ensure that the objects being trans-

ported are evenly distributed throughout

the loading area.

points 1 on the boot floor, if

these are fitted to the vehicle. The

luggage should be loaded in such a

way that no items will be thrown for-

ward and strike the occupants if the

driver has to brake suddenly. Fasten

the rear seat belts, even if the seats

are not occupied.

If you have to place objects on the folded

seatback, it is necessary that you lower

the headrests before folding the seat-

back so that it can be folded as flat as

possible against the seat.

3.28

Your comfort for Your Renault Zoe 4 Door Third Generation (2019-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals