2009-2017 Seat Ibiza SUV Emergencies -> Tyre repair User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Emergencies -> Tyre repair for Your Seat Ibiza SUV Fourth Generation (2009-2017)

Advice  
4 mm in diameter. Do not remove foreign ob-  
jects, e.g. screws or nails, from the tyre.  
Tyres with directional tread pattern  
●
Ensure the ground on which you park is flat  
and solid.  
A directional tread pattern can be identified  
by arrows on the sidewall that point in the di-  
rection of rotation. Always note the direction  
of rotation indicated when fitting the wheel.  
This is important so that these tyres can give  
maximum grip and avoid excessive noise,  
tread wear and aquaplaning.  
●
All passengers and particularly children  
must keep a safe distance from the work area.  
After inserting the sealant residue in the tyre,  
you must again check the tyre pressure about  
10 minutes after starting the engine.  
●
Turn on the hazard warning lights to warn  
other road users.  
You should only use the tire mobility set if  
the vehicle is parked in a safe place, you are  
familiar with the procedure and you have the  
necessary tire mobility set! Otherwise, you  
should seek professional assistance.  
●
Use the tyre mobility system only if you are  
familiar with the necessary procedures. Oth-  
erwise, you should seek professional assis-  
tance.  
If, in an emergency, you have to mount the  
spare wheel so it rotates in the wrong direc-  
tion, you must drive extremely carefully. The  
tyre will not give optimum performance. This  
is particularly important when driving on wet  
roads.  
●
The tyre mobility set is intended for tempo-  
rary emergency use only until you can reach  
the nearest specialised workshop.  
The tyre sealant must not be used in the  
following cases:  
●
Replace the repaired tyre with the tire mo-  
●
If the wheel rim has been damaged.  
In outside temperatures below -20 °C  
bility set as soon as possible.  
●
●
To benefit from the advantages of tyres with  
this type of tread pattern, the defective tyre  
should be replaced as soon as possible so  
that all tyres again rotate in the correct direc-  
tion.  
The sealant is a health hazard and must be  
(-4 °F).  
cleaned immediately if it comes into contact  
with the skin.  
●
In the event of cuts or perforations in the  
tyre greater than 4 mm.  
●
Always keep the tire mobility set out of the  
reach of small children.  
●
If you have been driving with very low pres-  
sure or a completely flat tyre.  
●
Never use an equivalent jack, even if it has  
been approved for your vehicle.  
●
If the sealant bottle has passed its use by  
date.  
●
Always stop the engine, apply the hand-  
Tyre repair  
brake lever firmly and engage gear if using a  
manual gearbox, in order to reduce the risk of  
vehicle involuntary movement.  
WARNING  
TMS (Tyre Mobility System)*  
Using the tyre mobility system can be dan-  
gerous, especially when filling the tyre at the  
roadside. Please observe the following rules  
to minimise the risk of injury:  
Read the additional information carefully  
WARNING  
›››  
page 26  
A tyre filled with sealant does not have the  
same performance properties as a conven-  
tional tyre.  
The Anti-puncture kit* (Tyre Mobility System)  
will reliably seal punctures caused by the  
penetration of a foreign body of up to about  
●
Stop the vehicle safely as soon as possible.  
Park it at a safe distance from surrounding  
traffic to fill the tyre.  
●
Never drive faster than 80 km/h (50 mph).  
186  
Emergencies  
7
Air bleed screw (in its place, the compres-  
sor may have a button).  
Contents of the tyre mobility system*  
●
Avoid heavy acceleration, hard braking and  
fast cornering.  
8
9
ON/OFF switch  
12 volt connector  
Bottle of sealant  
Spare tyre valve  
●
Drive for only 10 minutes at a maximum  
speed of 80 km/h (50 mph) and then check  
the tyre.  
10  
11  
For the sake of the environment  
1
The valve insert remover  
has a gap at the  
Dispose of used or expired sealant observing  
any legal requirements.  
lower end for a valve insert. The valve insert  
can only be screwed or unscrewed in this  
way. This also applies to its replacement part  
Note  
11  
.
●
A new bottle of sealant can be purchased at  
SEAT dealerships.  
WARNING  
●
Fig. 163 Standard representation: Contents  
of the tyre mobility system.  
Take into account the separate instruction  
When inflating the wheel, the air compressor  
and the inflator tube may become hot.  
manual of the tyre mobility set* manufactur-  
er.  
●
Protect hands and skin from hot parts.  
The tyre mobility set is located underneath  
the floor covering in the luggage compart-  
ment. It includes the following components  
››› Fig. 163:  
●
Do not place the hot flexible inflator tube or  
hot air compressor on flammable material.  
●
Allow them to cool before storing the de-  
vice.  
1
2
Tyre valve remover  
●
If it is not possible to inflate the tyre to at  
Sticker indicating maximum speed “max.  
80 km/h” or “max. 50 mph”  
least 2.0 bars (29 psi / 200 kPa), the tyre is  
too badly damaged. The sealant is not in a  
good condition to seal the tyre. Do not con-  
tinue driving. Seek specialist assistance.  
3
4
5
6
Filler tube with cap  
Air compressor  
Tube for inflating tyres  
CAUTION  
Warning provided by tyre pressure moni-  
toring system (it can also be integrated in  
the compressor).  
Switch off the air compressor after a maxi-  
mum of 8 operational minutes to avoid over-  
heating! Before switching on the air compres-  
sor again, let it cool for several minutes.  
187  
Advice  
Check after 10 minutes of driving  
How to jump start: description  
Jump-starting  
5
Screw in the inflator tube ››› Fig. 163  
Jump leads  
again and check the pressure on the gauge  
6
.
The jump lead must have a sufficient wire  
cross section.  
1.3 bar (19 psi / 130 kPa) and lower:  
If the engine fails to start because of a dis-  
charged battery, the battery can be connec-  
ted to the battery of another vehicle to start  
the engine.  
●
Stop the vehicle! The tyre cannot be sealed  
sufficiently with the tyre mobility set.  
●
You should obtain professional assistance  
.
›››  
Jump leads  
Fig. 164 Diagram of connections for vehicles  
without Start-Stop system.  
1.4 bar (20 psi / 140 kPa) and higher:  
Jump leads must comply with standard DIN  
72553 (see cable manufacturer's instruc-  
tions). The wire cross section must be at least  
25 mm2 for petrol engines and at least  
35 mm2 for diesel engines.  
●
Set the tyre pressure to the correct value  
again.  
●
Carefully resume your journey until you  
reach the nearest specialised workshop with-  
out exceeding 80 km/h (50 mph).  
Note  
●
Have the damaged tyre replaced.  
●
The vehicles must not touch each other,  
otherwise electricity could flow as soon as  
the positive terminals are connected.  
WARNING  
Driving with an unsealed tyre is dangerous  
and can cause accidents and serious injury.  
●
The discharged battery must be properly  
connected to the on-board network.  
●
Do not continue driving if the tyre pressure  
is 1.3 bar (19 psi / 130 kPa) and lower.  
Fig. 165 Diagram of connections for vehicles  
with Start-Stop system.  
●
Seek specialist assistance.  
Jump lead terminal connections  
1. Switch off the ignition of both vehicles  
›››  
.
188  

Related Topics

Popular Owner Manuals