132 Wheels › Tyre pressure
The purpose of the repair is to get you to the nearest
specialist garage.
There is damage to the tyre wall.
The expiry date stated on the tyre inflation bottle
▶
▶
has expired.
Change the tyre repaired by the breakdown kit as
soon as possible.
Before using the kit
Self-help
Park the vehicle safely and secure it against rolling
away.
›
Seal the tyres
Unscrew the valve cap from the damaged tyre.
Unscrew the valve core with the valve insert and
place it on a clean surface.
›
›
Turn off the engine.
Let all passengers get out. During the wheel repair
they should not stand on the road, e.g. behind the
crash barriers.
›
›
Shake the tyre inflation bottle back and forth with
sealant.
›
Close all doors as well as the luggage compartment
and engine compartment flaps.
›
Screw the inflation hose onto the tyre inflater bot-
tle. The film on the closure is pierced automatically.
›
If a trailer is coupled, uncouple it.
›
Remove the plug from the inflation hose and push
it fully onto the tyre valve.
›
After using the kit
If a tyre pressure of 2.0 bar cannot be achieved, the
tyre is too damaged and cannot be sealed with the
puncture set.
Hold the bottle with the bottom facing upwards
and fill all of the sealing agent into the tyre.
›
Remove the filler plug from the valve.
Screw in the valve insert.
›
›
Stop driving. Get the help of a specialist company.
›
Once a tyre pressure of 2.0–2.5 bar is achieved, con-
tinue the journey at a maximum speed of 80 km/h
(50 mph).
Inflate tyres
Fit the tyre inflation hose of the air compressor to
the tyre valve.
›
Avoid full throttle accelerations, hard braking and
fast cornering.
›
Secure the vehicle with the parking brake.
Start the engine.
Plug the connector into the 12 volt socket .
Turn on the air compressor.
Once a tyre pressure of 2.0-2.5 bar is reached, turn
off the air compressor.
›
›
Instructions for driving with repaired tires
›
The pressure of the repaired tyre must be checked
after driving for 10 minutes.
›
›
›
If the tyre pressure is 1.3 bar and less, do not con-
tinue! Get the help of a specialist company.
›
Observe the maximum running time of the air com-
pressor according to the directions of the repair kit
manufacturer.
If the tyre pressure is higher than 1.3 bar, correct
the pressure to the correct value of at least 2 bar
and continue driving.
›
If an air pressure of 2.0 - 2.5 bar has not been
reached, remove the tyre inflation hose from the
›
NOTICE
Danger of compressor damage!
valve.
After the maximum running time of the air com-
pressor has expired, let it cool down for a few mi-
nutes.
▶
Drive approx. 10 metres forwards or backwards to
allow the sealing agent to distribute in the tyre.
›
Replace the tire inflation hose on the valve and re-
peat the inflation procedure.
›
WARNING
Risk of burns!
Tyre pressure
What you should be mindful of
NOTICE
Always adjust the tyre pressure to the load.
Check the pressure in all tyres at least once a
month and before each longer ride.
▶
▶
Usage restrictions
Do not use the kit in the following cases.
Check the pressure when the tyres are cold. If nec-
essary, do not reduce the elevated pressure when
the tyres are warm.
After each change in tyre pressure, save the new
values in the tyre control display.
The rim is damaged.
▶
▶
▶
▶
The outdoor temperature is below the minimum
temperature indicated in the manual of the tyre fill-
ing bottle.
Tyre punctures are greater than 4 mm.
▶
English 
