Get Breakdown assistance Guide for Skoda Octavia 4 Door Second Generation (2004-2012)

Breakdown assistance 245

Breakdown assistance

First-aid box* and Warning triangle* (Octavia)

First-aid box* and warning triangle* (Estate car)

Fig. 221 Placing of the

warning triangle (Octavia)

Fig. 222 Placing of the

warning triangle (Estate car)

The first-aid box* is attached by a strap to the right-hand side of the luggage

compartment

For vehicles of the type estate car the first-aid box and the warning triangle are

housed in a compartment on the right side in the luggage compartment. You can

open the compartment by turning the locks in the direction of arrow ⇒ fig. 222.

The warning triangle can be attached to the trim panel of the rear wall with rubber

straps ⇒ fig. 221.

If you wish to equip your vehicle additionally with a warning triangle, please contact

a specialist garage.

If you wish to equip your vehicle additionally with a warning triangle, please contact

a specialist garage.

Note

Pay attention to the use-by-date of the contents of the first-aid box.

Note

Pay attention to the use-by-date of the contents of the first-aid box.

Fire extinguisher*

The fire extinguisher is attached with straps in a holder under the driver seat.

Please read carefully the instructions which are attached to the fire extin-

guisher.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

246 Breakdown assistance

The fire extinguisher must be checked by an authorised person or company annu-

ally (please observe the differing legal requirements).

ball for the trailer towing device*. The box is attached with a strap on the spare

wheel.

The vehicle tool kit contains the following parts (depending on equipment fitted):

WARNING

•

Wire clamps for removing the full wheel trims,

Plastic clip for a wheel bolt cover,

Wheel wrench*,

If the fire extinguisher is not correctly attached, in case of sudden manoeu-

vres or an accident it can be “thrown” through the interior compartment and

cause injuries.

Towing eye,

Adapter for the wheel bolts lock.*

20)

Note

Screwdriver* for removing the front fog lights

.

•

The fire extinguisher must comply with the relevant and valid legal require-

After using the lifting jack*, screw in the arm of the lifting jack fully before placing it

back in its storage area.

ments.

•

Pay attention to the expiration date of the fire extinguisher. If the fire extin-

guisher is used after the expiration date, its proper function is no longer assured.

WARNING

•

The fire extinguisher is only supplied in certain countries within the scope of

delivery.

•

The factory-supplied lifting jack* is only intended for your model of

vehicle. On no account attempt to lift a heavier vehicle or other loads - risk

of injury!

Vehicle tool kit

•

Ensure that the vehicle tool kit is safely attached in the luggage compart-

ment.

Note

Ensure that the box is always secured with the strap.

Tyre repair kit*

Fig. 223 Luggage compart-

ment: storage compartment

for vehicle tool kit

The tyre repair kit is intended for the repair of minor tyre defects. The tyre repair kit

contains a compressor, inflation bottle, operating instructions and accessories.

The repair with the tyre repair kit is not at all intended to replace a permanent

repair on the tyre, this repair only serves to reach the next specialist garage. The

The vehicle tool kit and the lifting jack*, on which a note sticker is affixed, are stored

in a box in the spare wheel* ⇒ fig. 223. There is also space here for the removable

20)

Valid for Octavia RS and Octavia Scout.

Breakdown assistance 247

repair can be undertaken on the vehicle immediately. Please read the attached

instructions carefully before the repair.

•

After fitting on the wheel, the warning sticker must not be concealed (e.g. by the

wheel trim).

•

Do not drive with this spare wheel at more than 80 km/h - risk of accident. Avoid

accelerating at full throttle, sharp braking and fast cornering.

The tyre repair kit is located in a textile bag. There is a velcro fastener on the under-

side of the bag, with which the bag is attached to the floor covering of the luggage

compartment in such a way that the side of the bag rests on the right side of the

luggage compartment and on the seat backrest.

•

The inflation pressure for this spare wheel is identical to the inflation pressure

of the standard tyres. The temporary spare wheel R 18 must have an inflation pres-

sure of 420 kPa (4.2 bar)!

•

Use this spare wheel only to reach the nearest specialist garage as it is not

intended for continuous use.

No other summer or winter tyres must be mounted on the rim of the spare

Spare wheel*

•

wheel R 18.

Changing a wheel

Preliminary work

The following steps should be carried out before actually changing the

wheel.

Fig. 224 Luggage compart-

ment: Spare wheel

–

If it is necessary to change a wheel, park the vehicle as far away as

possible from the traffic flow. The place you choose should be level.

The spare wheel lies in a well under the floor covering of the luggage compartment

and is fixed in place using special screws ⇒ fig. 224.

–

Have all the occupants get out. While changing a wheel, the occu-

pants of the vehicle should not stand on the road (e.g. behind a crash

barrier).

Before removing the spare wheel, you must take out the box with the vehicle tool

kit box ⇒ page 246, fig. 223.

One should check the inflation pressure in the spare wheel (at best when generally

checking the tyre air pressures - see sign on the fuel filler flap ⇒ page 238) to

ensure that the spare wheel is always ready to use.

–

Apply the handbrake firmly.

Engage 1st gear or if your vehicle is fitted with an automatic gearbox,

position the selector lever into position P.

Temporary spare wheel

–

If a trailer is coupled, uncouple it.

A warning label displayed on the rim of the temporary spare wheel indicates that

your vehicle is equipped with a temporary spare wheel.

Take the vehicle tool kit ⇒ page 246 and the spare wheel*

⇒ page 247 out of the luggage compartment.

Please observe the following notes when driving with a temporary spare wheel:

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

248 Breakdown assistance

WARNING

–

Fit on the spare wheel and tighten the wheel bolts slightly.

Lower the car.

•

If you find yourself in flowing traffic switch on the hazard warning lights

Tighten the wheel bolts firmly, alternately and diagonally using the

wheel wrench* (crosswise) and last the safety wheel bolt*

⇒ page 250.

system and place the warning triangle on the side of the road at the

prescribed distance from your vehicle while observing all national legal

provisions. In this way you are protecting not only yourself but also other

road users.

–

Mount the full wheel trim/wheel trim cap or the caps.

•

Never start the engine with the vehicle sitting on the raised jack - danger

of suffering injury.

Note

•

All bolts must be clean and must turn easily.

You must never grease or oil the wheel bolts!

When fitting on unidirectional tyres, ensure that the tyres rotate in the correct

Caution

If you have to change a wheel on a slope first block the opposite wheel with a stone

or similar object in order to secure the vehicle from unexpectedly rolling away.

direction ⇒ page 238.

Note

Subsequent steps

Comply with the national legal regulations.

After changing the wheel, you must perform the following steps.

Changing a wheel

–

Stow and attach the replaced wheel in the spare wheel well.

Stow the vehicle tool kit in the space provided.

Always change a wheel on a level surface as far as possible.

–

Take off the full wheel trim* ⇒ page 249 or the caps ⇒ page 249.

Check the tyre pressure on the spare wheel just mounted as soon as

possible.

In the case of light alloy wheels remove the wheel trim cap

⇒ page 250.

–

Have the tightening torque of the wheel bolts checked with a torque

wrench as soon as possible. Steel and light alloy wheels must be tight-

ened to a tightening torque of 120 Nm.

–

First of all slacken the safety wheel bolt * and afterwards the other

wheel bolts ⇒ page 250.

Have the defective tyre repaired as soon as possible.

Jack up the vehicle until the wheel to be changed is clear of the ground

⇒ page 251.

Unscrew the wheel bolts and place them on a clean surface (cloth,

paper etc.).

Take off the wheel.

Breakdown assistance 249

First check for yourself that the theft-deterrent wheel bolt is located

•

WARNING

⇒ page 251 in the hole in the area of the valve before fitting the full wheel trim onto

a steel wheel which is attached with a theft-deterrent wheel bolt.

It is necessary to observe the guidelines given on ⇒ page 240 if the vehicle is

subsequently fitted with tyres which are different to those it was fitted with

at the works.

Wheel bolts with caps*

Note

•

If you find, when changing the wheel, that the wheel bolts are corroded and

difficult to turn, the bolts must be replaced before checking the tightening torque.

•

Drive cautiously and only at a moderate speed to a workshop where the tight-

ening torque can be checked.

Full wheel trim*

Pulling off

Fig. 225 Removing the cap.

–

Hook the clamp found in the vehicle tool kit into the reinforced edge

of the full wheel trim.

Pulling off

–

Push the wheel wrench* through the clamp, support the wheel

wrench* at the tyre and pull off the wheel trim.

–

Push the plastic clip sufficiently far onto the cap until the inner catches

of the clip are positioned at the collar of the cap and detach the cap.

Installing

–

First press the full wheel trim onto the wheel at the valve opening

–

Push the caps fully onto the wheel bolts.

provided. Then press the full wheel trim into the wheel in such a way

that its entire circumference locks correctly in place.

The caps are located in the well of the luggage compartment.

Caution

•

Use the pressure of your hand, do not knock on the full wheel trim! Heavy

knocks mainly on the points where the full wheel trim has not been inserted into

the wheel, can result in damage to the guide and centering elements of the full

wheel trim.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

250 Breakdown assistance

Wheel trim caps*

Slackening wheel bolts

21)

–

Push the wheel wrench* fully onto the wheel bolt

.

Grasp the end of the wrench and turn the bolt about one turn to the

left ⇒ fig. 227.

Tightening wheel bolts

21)

–

Push the wheel wrench* fully onto the wheel bolt

.

Grasp the end of the wrench and turn the bolt to the right until it is

tight.

Fig. 226 Pulling off wheel

trim cap on light alloy wheels

WARNING

Pulling off

Slacken the wheel bolts only a little (about one turn) as long as the vehicle

has not yet been lifted with the lifting jack* - risk of accident!

–

Carefully remove the wheel trim cap using the wire clamp

⇒ fig. 226.

Note

Apply pressure carefully with your foot to the end of the wheel wrench* if it proves

difficult to slacken the bolts. Hold tight on the vehicle when doing this and ensure

that you have a steady position.

Slackening and tightening wheel bolts

Slacken the wheel bolts before jacking up the vehicle.

Fig. 227 Changing a wheel:

Slackening wheel bolts

21)

Use the appropriate adapter for slackening and tightening the safety wheel bolts

⇒ page 251.

Breakdown assistance 251

Raise vehicle

WARNING

You have to raise the vehicle with the lifting jack* in order to be able

to take off the wheel.

•

Always raise the vehicle with the doors closed - risk of injury!

Take suitable measures to prevent the base of the lifting jack from slip-

ping off - risk of injury!

•

Not positioning the lifting jack* at the specified points can result in

damage to the vehicle. The lifting jack* can also slip off if it does not have

sufficient grip - risk of injury!

•

It is important to support the vehicle with suitable supporting blocks if

you wish to work under the lifted vehicle - risk of injury!

Securing wheels against being stolen*

Fig. 228 Changing a wheel:

Points for positioning car jack

You need a special adapter for slackening the safety wheel bolts.

Position the lifting jack* by selecting the jacking point which is closest to

the wheel to be removed ⇒ fig. 228. The jacking point is located directly

below the engraving in the lower sill. The engraving is only visible after

opening the door.

–

Position the lifting jack* below the jacking point and move it up until

its claw is positioned directly below the vertical web of the lower sill.

A

Align the lifting jack* so that its claw grasps the web of the lower sill A

Fig. 229 Safety wheel bolt

with adapter

B

and the base plate A is resting flat on the floor.

Turn the lifting jack* up further until the wheel is just clear of the

ground.

–

Pull off the full wheel trim/cap from the wheel hub or cap from the

safety wheel bolt.

Ground which is soft and slippery below the lifting jack* can cause the vehicle to

slip off the lifting jack*. It is therefore always necessary to place the lifting jack* on

a solid surface or use a wide and stable base. Use a non-slip base (e.g. a rubber foot

mat) if the surface is smooth, such as cobbled stones, a tiled floor, etc.

B

Insert the adapter Awith its toothed side fully into the inner toothing

of the safety wheel bolt A right down in such a way that only the

A

outer hexagon is jutting out ⇒ fig. 229.

B

–

Insert the wheel wrench* fully onto the adapter A.

Slacken the wheel bolt, or tighten it firmly ⇒ page 250.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

252 Breakdown assistance

Both batteries must have a rated voltage of 12 V. The capacity (Ah) of the battery

supplying the power must not be significantly less than the capacity of the

discharged battery in your vehicle.

–

Reinstall the full wheel trim/wheel cap after removing the adapter or

place the cap onto the safety wheel bolt.

Have the tightening torque checked with a torque wrench as soon as

possible. Steel and light alloy wheels must be tightened to a tightening

torque of 120 Nm.

Jump-start cables

Only use jump-start cables which have an adequately large cross-section and insu-

lated terminal clamps. Please pay attention to the manufacturer's instructions.

The safety wheel bolts on vehicles fitted with them (one safety wheel bolt per

wheel) can only be loosened or tighten up by using the adapter provided.

Positive cable - colour coding in the majority of cases red.

Negative cable - colour coding in the majority of cases black.

It is meaningful to note the code number hammered into the rear side of the

adapter or the rear side of the safety wheel bolts. You can obtain a replacement

adapter from an authorised Škoda Service Partner, if necessary, by quoting this

number.

WARNING

•

A discharged battery may already freeze at temperatures just below 0°C.

In case of frozen battery carry out no jump-starting - risk of explosion!

Please pay attention to the warning instructions relating to working in

We recommend that you always carry the adapter for the wheel bolts with you in

the vehicle. It should be stowed in the vehicle tool kit.

•

the engine compartment ⇒ page 225, “Working in the engine compart-

ment”.

Caution

Damage can occur to the adapter and safety wheel bolt if the safety wheel bolt is

tightened up too much.

Note

•

There must not be any contact between the two vehicles otherwise current may

flow as soon as the negative terminals are connected.

Note

•

The discharged battery must be properly connected to the system of the

vehicle.

The set of safety wheel bolts can be obtained from an authorised Škoda Service

Partner.

•

Switch off any mobile phone, pay attention to the instructions for use of the

mobile phone in such a situation.

Jump-starting

•

We recommend purchasing jump-start cables from Škoda Service Partners as a

Škoda original accessory or from retailers who sell branded batteries.

Initial steps

You can use the battery of another vehicle for jump-starting yours if the engine

does not start because the battery on your vehicle is flat. You will require jump-start

cables for this purpose.

Breakdown assistance 253

–

Interrupt the attempt at starting an engine after 10 seconds if it does

not start right away and wait for about 30 seconds before repeating

the attempt.

Start engine

Disconnect the cables on the engine in exactly the reverse order they

were connected up.

WARNING

Fig. 230 Jump-startingusing

the battery from another

vehicle: A - flat vehicle

battery, B - battery providing

current

•

The non-insulated parts of the terminal clamps must never make contact

with each other. Furthermore, the cable connected to the positive terminal

of the battery must not come into contact with electrically conducting parts

of the vehicle - risk of a short circuit!

•

Do not affix the jump starting cables to the negative terminal of the

discharged battery. There is the risk of detonating gas seeping out the

battery being ignited by the strong spark which results from the engine

being started.

It is important to connect the jump-start cables in the correct order.

Connecting positive terminals

•

Run the jump-start cables so that they cannot be caught by any rotating

parts in the engine compartment.

1

–

Attach one end A to the positive terminal ⇒ fig. 230 of the

A

discharged battery A.

•

Do not bend over the batteries - risk of caustic burns!

2

–

Attach the other end A to the positive terminal of the battery

supplying the power A.

The vent screws of the battery cells must be tightened firmly.

Keep any sources of ignition (naked flame, smouldering cigarettes etc.)

B

away from the battery - risk of an explosion!

Connecting negative terminal and engine block

•

Never jump-start the batteries which have a too low electrolyte level -

3

–

Attach one end A to the negative terminal of the battery supplying

risk of explosion and caustic burns!

B

the power A.

4

–

Attach the other end A to a solid metal part which is connected

Tow-starting and towing vehicle

firmly to the engine block, or to the engine block itself.

General

Starting engine

–

Start the engine of the vehicle providing current and run the engine at

idling speed.

Please pay attention to the following instructions if you are going to use a

tow rope:

–

Now start the engine of the vehicle with the discharged battery.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

254 Breakdown assistance

Driver of the towing vehicle

the points to which you attach the tow rope or tow bar when you attempt to tow a

vehicle which is not standing on a paved road.

–

Do not drive off until the tow rope is taught.

Release the clutch particularly gently when starting off or depress the

accelerator particularly gently if your vehicle is fitted with an auto-

matic gearbox.

Caution

If the gearbox of your vehicle no longer contains any oil because of a defect, your

vehicle must only be towed in with the driven wheels raised clear of the ground, or

on a special vehicle transporter or trailer.

Driver of the towed vehicle

–

Switch the ignition on so that the steering wheel is not blocked and

you can also operate the turn signal lights, the headlight flasher, the

windscreen wipers and windscreen washer system.

Note

•

Please comply with any legal requirements particularly regarding the switched

on signal systems, when towing in or tow-starting another vehicle.

The tow rope must not be twisted as it may in certain circumstances result in the

–

Take the vehicle out of gear or move the selector lever into position N

if your vehicle is fitted with an automatic gearbox.

•

front towing eye being unscrewed out of your vehicle.

Note that the brake servo unit and power steering only operate if the

engine is running. You will require significantly greater physical force

to depress the brake pedal and to steer the vehicle if the engine is not

running.

Front towing eye

The towing eye is stored in the box for the vehicle tool kit.

–

Ensure that the tow rope is always kept taught.

Tow rope or tow bar

A tow bar is safest way of towing a vehicle and also minimizes any shocks. You can

use a tow rope only if a suitable tow bar is not available.

The tow rope must be elastic to protect the vehicle. Thus one should only use

plastic fibre rope or a rope made out of a similarly elastic material.

Only attach the tow rope to the towing eyes provided for this purpose ⇒ page 254

and ⇒ page 256.

Fig. 231 Front bumper:

Protective grille

Driving style

Towing another vehicle requires a certain amount of practice. Both drivers should

be familiar with the particular points about towing a vehicle. Unskilled drivers

should not attempt to tow in another vehicle or to be towed in.

One should be constantly vigilant not to allow impermissibly high towing forces or

jerky loadings. There is always a risk of excessive stresses and damage resulting at

Breakdown assistance 255

Front towing eye for Octavia RS and Octavia Scout

The towing eye is stored in the box for the vehicle tool kit.

Fig. 232 Front bumper:

Installing the towing eye

Carefully remove the cover as follows.

Fig. 233 Front bumper

Octavia RS: Protective grille

A

–

Guide the fingers into the opening A ⇒ page 254, fig. 231.

1

By pulling in the direction of arrow A, first of all slacken the cover in

the upper area on the side to the fog lights.

–

Afterwards, also slacken the cover on the other side in the direction of

2

arrow A and remove it.

Screw in the towing eye by hand anticlockwise down to the stop

⇒ fig. 232 and tighten up using the wheel wrench* (push the wheel

wrench* through the eye).

Fig. 234 Front bumper

Octavia Scout: Cover

–

In order to reinstall the cover after screwing out the towing eye, first of

all insert it starting on the side facing the marking. Then press the

cover closed on the side facing the fog light. The cover must engage

firmly.

Octavia RS

A

–

Guide one finger into the opening A of the grille ⇒ fig. 233.

1

Unlock the cover by pulling it in direction A and remove it.

Screw in the towing eye by hand anticlockwise down to the stop

⇒ fig. 232 and tighten up using the wheel wrench* (push the wheel

wrench* through the eye).

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

256 Breakdown assistance

–

After screwing out the towing eye, reinsert the cover and lock it in

place. The cover must engage firmly.

Octavia Scout

–

Press on the upper part of the cover ⇒ page 255, fig. 234 and remove

it.

–

Screw in the towing eye by hand anticlockwise down to the stop

⇒ page 255, fig. 232 and tighten up using the wheel wrench* (push

the wheel wrench* through the eye).

Fig. 236 Rear bumper:

Installing the towing eye

–

After screwing out the towing eye, reinsert the cover and lock it in

place. The cover must engage firmly.

–

Unlock the bottom part of the cover by pulling it downwards in direc-

1

tion of arrow A ⇒ fig. 235.

Unlock the upper part of the cover by pulling it in direction of arrow

Rear towing eye

2

A and remove it.

Screw in the towing eye by hand anticlockwise down to the stop

⇒ fig. 236 and tighten up using the wheel wrench* (push the wheel

wrench* through the eye).

–

In order to reinstall the cover after screwing out the towing eye, first of

all insert the upper part of the cover and then press in the lower part.

The cover must engage firmly.

Fig. 235 Rear bumper:

Removing cover

Towing in a vehicle fitted with a manual gearbox

Please refer to the notes ⇒ page 253.

The vehicle can be towed in with a tow bar or a tow rope or with the front or rear

wheels raised. The maximum towing speed is 50 km/h.

Towing of a vehicle with an automatic gearbox

Please refer to the notes ⇒ page 253.

Breakdown assistance 257

The car can be towed in with a tow bar or a tow rope. Refer at the same time to the

following guidelines:

•

Move selector lever into N.

The maximum towing speed is 50 km/h.

The maximum permissible towing distance is 50 km. The gear oil pump does

not operate when the engine is not running; the gearbox would not be adequately

lubricated at higher speeds and over longer towing distance.

Caution

If the vehicle is towed in by a recovery vehicle, it should only be towed in with the

front wheels raised. If the vehicle is raised at rear, the automatic gearbox is

damaged! (Does not apply to the automatic gearbox DSG).

Note

The vehicle must be transported on a special vehicle or trailer if it is not possible to

tow in the vehicle in the way described or if the towing distance is greater than

50 km.

Towing a vehicle with four-wheel drive

Please refer to the notes ⇒ page 253.

The vehicle can be towed in using a tow bar or a tow rope or with the front axle

raised.

The maximum towing speed is 50 km/h, the maximum permissible towing

distance is 50 km.

Note

The vehicle must be transported on a special vehicle or trailer if it is not possible to

tow in the vehicle in the way described or if the towing distance is greater than

50 km.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

258 Fuses and light bulbs

Fuses and light bulbs

Electric fuses

–

Defect fuses can be detected by their melted metal strips. Replace the

defect fuse by a new fuse of the same ampere number.

Replacing fuses

Fit on the fuse cover again.

Defect fuses must be replaced.

We recommend that you always have the small box of replacement fuses in your

vehicle. You can obtain replacement fuses from Škoda original accessories or from

22)

a specialist garage

.

Colour coding of fuses

Colour

light brown

brown

red

Maximum amperage

5

7,5

10

15

20

25

30

40

50

Fig. 237 Fuse cover: left side

of the dash panel

blue

yellow

white

Individual electrical circuits are protected by fuses. The fuses are located

on the left side of the dash panel behind the safety cover and under the

cover in the engine compartment on the left.

green

orange

red

–

Switch the ignition off and also the electrical component affected.

Use a screwdriver to take off the fuse cover on the side of the dash

panel ⇒ fig. 237 or the fuse cover in the engine compartment

⇒ page 259.

Caution

•

Never attempt to “repair” fuses and also do not replace them with a fuse of a

higher amperage - risk of fire! This may also cause damage at another part of the

electrical system.

–

Find out which fuse belongs to the relevant component ⇒ page 260,

“Fuse assignment in the dash panel” or ⇒ page 259, “Fuse assignment

in engine compartment”.

•

Have the electrical system checked as quickly as possible by a specialist garage

if a newly inserted fuse blows again after a short time.

Take the plastic clip out of its fixture in the fuse cover, insert it onto the

respective fuse and pull out this fuse.

22)

The small box with replacement fuses is part of the basic equipping of the vehicle in some

countries.

Fuses and light bulbs 259

Fuse cover in engine compartment

Fuse assignment in engine compartment

The fuse box in the engine compartment exists in two different

versions. You can determine which version your vehicle is fitted with

after removing the fuse cover at the location of the fuses.

Fig. 239 Schematic repre-

sentation of fuse carrier in

engine compartment

Certain electrical components are only standard on certain vehicle model versions

or only suppliable as optional equipment for certain models.

Fig. 238 Fuse cover in engine

compartment

No. Power consumer

Amperes

On some vehicles, the battery cover must be removed before removing

the fuse cover ⇒ page 232.

F1 Not assigned

F2 Control unit for automatic gearbox DQ 200

F3 Measuring circuit

30

5

Removing fuse cover

A

–

Move the circlips A ⇒ fig. 238 as far as the stop, the symbol 

F4 Valves for ABS

30/20

15

appears behind the circlip and remove the cover.

F5 Control unit for automatic gearbox

Installing fuse cover

Instrument cluster, windshield wiper lever and turn sig-

nal light lever

5

F6

A

–

Position the fuse cover on the fuse box and push the circlips Aas far

as the stop - the symbol  is visible behind the circlip.

F7 Power suppy terminal 15, Starter

F8 Radio

40

15

5

Caution

F9 Phone

•

When unlocking and locking the fuse cover, it must be pressed on the sides to

the box, otherwise damage can occur to the locking mechanism.

F10 Engine control unit, Main relay

F11 Control unit for auxiliary heating

F12 Control unit for CAN databus

5/10

20

5

•

Carefully position the fuse cover in the engine compartment. If the cover was

not correctly positioned, water can get into the fuses and this results in a damage

to the vehicle!

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

260 Fuses and light bulbs

Fuse assignment in the dash panel

No. Power consumer

F13 Engine control unit

F14 Ignition

Amperes

15/30

20

Lambda probe

10

15

5

NO sensor, fuel pump relay

F15

x

Glow plug system relay

Central control unit, right main headlight, right rear light

unit

30

F16

Fig. 240 Schematic repre-

sentation of the fuse carrier

in the dash panel

F17 Horn

15

30

F18 Amplifier for digital sound processor

F19 Front window wiper

Certain electrical components are only standard on certain vehicle model versions

or only suppliable as optional equipment for certain models.

Water pump

F20

10

20

valve for fuel dosing

F21 Lambda probe

10/15

5

No. Power consumer

Amperes

F22 Clutch pedal switch, brake pedal switch

Diagnostic socket, Engine control unit, Electrical fuel

pump

1

10

Secondary air pump

F23 Air mass meter

5

10

15

2

3

4

5

Control unit for ABS, ESP

5

Fuel high pressure pump

Airbag

F24 Activated charcoal filter, exhaust gas recirculation valve

F25 Pump for ABS

10

30/40

30

Heating, Air conditioning system, Reversing lights

Control unit for headlamp beam adjustment

Central control unit, left main headlight, left rear light

F26

unit

Instrument cluster, Control unit for automatic gearbox,

Control unit for electromechanical power steering,

Parking aid; Haldex clutch

6

5

Secondary air pump

F27

40

50

Glow plug system

7

8

9

Not assigned

F28 Not assigned

F29 Power supply terminal 30

50

a)

F30

Terminal X

10 Not assigned

11 Not assigned

a)

In order not to drain the battery unnecessarily when starting the engine, the electrical com-

ponents of this terminal are automatically switched off.

Fuses and light bulbs 261

No. Power consumer

Amperes

No. Power consumer

36 Headlight cleaning system

37 Front seat heating

38 Heated rear seats

Amperes

12 Central locking control unit

13 Diagnostic socket, Light switch

14 Control unit for automatic gearbox, Selector lever lock

15 Central control unit - interior lights

16 Climatronic

10

5

20

30

5

39 Not assigned

10

40 Air blower for heating and air conditioning

41 Rear window wiper

42 Not assigned

40

15

17 Not assigned

18 Not assigned

19 Control unit for trailer detection

20 Not assigned

5

43 Towing device

15

20

15

5

44 Towing device

21 Cornering lights for the left and right side

22 Air blower for Climatronic

23 Front power window

10

40

30

25

45 Towing device

46 Heated windscreen washer nozzles

47 Relay for auxiliary heating

48 Not assigned

5

24 Cigarette lighter

Rear window heater

25 Rear window heater, Auxiliary heating (auxiliary heating

and ventilation)

49 Light switch

5

25

30

Electrically adjustable seats are protected by automatic circuit breakers, which

switch on again automatically after a few seconds after the overload has been

eliminated.

26 Power socket in the luggage compartment

27 Fuel pump relay, Injection valves (diesel engine)

28 Not assigned

20

15

Bulbs

29 Engine control unit, Crankcase ventilation heater

30 Control unit for automatic gearbox

31 Vacuum pump

10

20

30

25

20

5

Changing bulbs

The relevant lamp must always be switched off before a light bulb is replaced.

32 Rear power window

Defect light bulbs should only be replaced with light bulbs of the same type. The

designation is located on the light socket or the glass bulb.

33 Electric sliding/tilting roof

34 Control unit for convenience functions

35 Anti-theft alarm system

Changing certain bulbs is not something which you can do yourself, but requires to

be done by a specialist. Other parts of the vehicle must be removed in order to

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

262 Fuses and light bulbs

change the light bulbs. This applies, in particular, to bulbs which can only be

reached from the engine compartment.

Light unit (Octavia)

Reversing light

Turn signals

Bulb

P21W

PY21W

We therefore recommend that you have any bulbs changed by an authorised Škoda

Service Partner or, in exceptional cases, by calling on other professional assistance.

Please note that the engine compartment is a hazardous area ⇒ page 225,

“Working in the engine compartment”.

Twin filament light bulb for the brake lights and tail

lights

P21/4W

We recommend that you always have a small box of replacement bulbs in your

Twin filament light bulb for the rear fog lights and tail

lights

P21/4W

W3W

vehicle. You can obtain replacement bulbs from Škoda original accessories or from

23)

a specialist garage

.

Parking lights

The set of light bulbs can be stowed in the locable box in the spare wheel.

Fitted with a xenon headlight

Rear light unit (Combi)

Bulb

Change of light bulbs on Xenon lights (low beam lights, parking lights and main

beam lights) should be undertaken by a specialist garage.

Reversing lights, brake lights, tail lights and rear fog

light

P21W

Overview of bulbs

Turn signals

PY21W

W3W

Parking lights

Front headlight

Low beam light

Main beam light

Parking lights

Halogen headlight

Xenon headlight

H7

D1S

Others

Bulb

LED

H1

W5W/W5W BL

Side turn signal lights

Licence plate light

3. Brake light

C5W

LED

a)

Daylight driving lights*

PY21W SLL/LED

PY21W

Turn signals

Fog lights

Entry lighting

W5W

C10W

W5W

C10W

W5W

C5W

C3W

a)

H8/HB4

front interior lighting

Reading lights

a)

Octavia RS, Octavia Scout

Rear interior lighting

Luggage compartment light

Door warning light

Lighting in storage compartment

23)

The small box with replacement bulbs is part of the basic equipping of the vehicle in some

countries.

Fuses and light bulbs 263

Positions of the light bulbs in the front headlight ⇒ fig. 241.

WARNING

A

A - Front turn signal light

•

Bulbs H7 and H1 are pressurised and may burst when changing the bulb

B

A - parking lights and low beam

- risk of injury!

It is recommended to wear gloves and eye protection when changing a

light bulb.

C

A - main beam light

•

Gas discharge bulbs* (xenon bulbs) operate with a high voltage, profes-

sional knowledge is required - danger to life!

Removing the headlight

Caution

Do not take hold of the glass bulb with naked fingers (even the smallest amount of

dirt reduces the working life of the light bulb). Use a clean cloth, serviette or some-

thing similar.

Note

This Owner's Manual only describes the replacement of bulbs where it is assumed

that no major complications will arise. Other light bulbs should be replaced by your

specialist garage.

Fig. 242 Front headlight:

Installing the light bulbs

The headlight must be removed in order to change the light bulb of the

parking lights, low beam lights and main beam lights as well as the turn

signal lights.

Front headlight

Removing the headlight

–

Switch the ignition and all lights off.

Open the bonnet ⇒ page 224.

A

Unscrew the plastic nut A ⇒ fig. 242.

B

Pull the fuse A in upward direction.

Fig. 241 Front headlight:

Installing the light bulbs

Pull the locking lever of the headlight as far as the stop in the direction

1

of arrow A.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

264 Fuses and light bulbs

Unplug the plug connector and carefully take out the headlight in the

–

Insert the socket with the changed light bulb into the headlight and

secure it by turning in the direction of arrow CLOSE (close) to the

right.

2

direction of arrow A.

Installation takes place in the reverse order.

Note

We recommend that you have the headlight setting checked by a specialist garage

after installing the headlight.

We recommend that you have the headlight setting checked by a specialist garage

after installing the headlight.

Front parking lights and low beam

Turn signal light at the front

Fig. 244 Removing the bulbs

for the parking and low beam

light

Fig. 243 Removing the light

bulb for the turn signal light

Removing the light bulb for the parking light

Changing light bulb for turn signal light (at the front)

–

Switch the ignition and all lights off.

–

Switch the ignition and all lights off.

Remove the headlight ⇒ page 263.

B

Remove the protective cap A ⇒ page 263, fig. 241.

Turn the socket in the direction of arrow OPEN (open) and take it out

together with the light bulb for the turn signal light ⇒ fig. 243.

A

Remove the socket A ⇒ fig. 244.

Take the faulty bulb out of the socket and insert a new one.

Insert the protective cap.

–

Press the defective light bulb into the socket, turn to the left and

remove.

Press a new light bulb into the socket and turn the light bulb to the

right as far as the stop.

Fuses and light bulbs 265

Removing the light bulb for the low beam light

–

Remove the headlight ⇒ page 263.

–

Switch the ignition and all lights off.

C

Remove the protective cap A ⇒ page 263, fig. 241.

Remove the headlight ⇒ page 263.

A

Unplug plug A ⇒ fig. 245.

B

Remove the protective cap A ⇒ page 263, fig. 241.

B

Press the wire clamps A in the direction of the headlight and then

unhook them to the side.

B

Turn the connector with the light bulb A up to the stop towards the

left and remove ⇒ page 264, fig. 244.

C

–

Remove the light bulb A and insert the new light bulb in such a way

that the fixing lugs of the light bulb socket fit into the recesses at the

reflector.

–

Replace the lamp, insert the connector with the new lamp and turn to

the right up to the stop.

Installation takes place in the reverse order.

Insert the protective cap.

Note

We recommend that you have the headlight setting checked by a specialist garage

after installing the headlight.

•

In order to facilitate the removal of the socket with the bulb for the parking light,

we recommend to remove first of all the bulb for the low beam light.

•

We recommend that you have the headlight setting checked by a specialist

garage after installing the headlight.

Fog lights and daylight driving lights*

Main beam light

Fig. 246 Front bumper:

Protective grille

Fig. 245 Removing the light

bulb for the main beam light

–

Switch the ignition and all lights off.

Using the system Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

266 Fuses and light bulbs

–

For the installation, first of all insert the fog light with the interlock to

the side far away from the marking of the vehicle.

–

Press into place the headlight onto the side facing the marking.

In order to reinstall the cover, first of all insert one part of the cover

starting on the side facing the marking. Then press the cover closed on

the side facing the fog light. The cover must engage firmly.

Fig. 247 Removing the front

fog light

Cover of fog lights Octavia RS, Octavia Scout

A

B

Connector A- bulb for daylight driving lights* ⇒ fig. 247. Connector A

- bulb for fog lights.

Removing the cover

–

Switch the ignition and all lights off.

A

Guide the fingers into the opening A ⇒ page 265, fig. 246.

1

By pulling in the direction of arrow A, first of all slacken the cover in

the upper area on the side to the fog lights.

Fig. 248 Front bumper:

Octavia RS

–

Afterwards, also slacken the cover on the other side in the direction of

2

arrow A and remove it.

Removing the fog light

–

Guide your hand into the opening, in which the cover was located,

and press the spring bolt ⇒ fig. 247.

–

Take out the fog light.

Turn the connector with the light bulb up to the stop towards the left

and remove.

Fig. 249 Front bumper:

Octavia Scout

–

Replace the lamp, insert the connector with the new lamp and turn to

the right up to the stop.

Fuses and light bulbs 267

Removing the cover - Octavia RS

–

Switch the ignition and all lights off.

Guide one finger into the opening ⇒ page 266, fig. 248 and remove

the cover.

Removing the cover - Octavia Scout

–

Switch the ignition and all lights off.

Fig. 251 Fog lights: Changing

the bulb

Guide the wire clamp from the vehicle tool kit into the opening above

the fog light ⇒ page 266, fig. 249 and remove the cover.

Removing the fog light

Fog lights Octavia RS, Octavia Scout

–

Screw out the screws with the aid of the screwdriver*, which is part of

24)

the vehicle tool kit ⇒ fig. 250.

–

Take out the fog light.

Changing the bulb and installing the fog light

1

A

–

Press the locking button A⇒ fig. 251 of the plug Aand remove the

B

plug from the socket A.

B

Turn the socket A with the bulb to the left up to the stop and take it

out.

Fig. 250 Front bumper: Fog

lights

Change the bulb, insert again the socket with the new bulb and turn it

to the right up to the stop.

A

B

–

Connect the plug A to the socket A.

Screw in the screws again and insert the cover. The cover must engage

firmly.

24)

Valid for Octavia RS and Octavia Scout.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

268 Fuses and light bulbs

Light unit (Octavia)

–

Press a new light bulb into the socket and turn the light bulb to the

right as far as the stop.

Insert the lamp holder in such a way that the catches lock in place in

the housing.

Close and lock the cover of the lamp holder.

Change the light bulb for the parking light

–

Switch the ignition and all lights off.

Fig. 252 Luggage compart-

ment: Cover for the lamp

holder

Unlock the locking button and open the cover of the lamp holder

⇒ fig. 252.

1

2

–

Take the defective light bulb (arrow A or A ⇒ fig. 253) out of the

housing and replace it with a new one.

Close and lock the cover of the lamp holder.

Rear light unit (Combi)

Fig. 253 Removing the lamp

holder

Changing light bulbs in the lamp holder

–

Switch the ignition and all lights off.

Unlock the locking button and open the cover of the lamp holder

⇒ fig. 252.

Fig. 254 Luggage compart-

ment: Side compartment

–

Press the catches in the direction of arrow and take out the lamp

holder ⇒ fig. 253.

Press the defective light bulb into the socket, turn to the left and

remove.

Fuses and light bulbs 269

–

Take out the cover of the lamp holder on the luggage compartment

side.

1

2

Take the defective light bulb (arrow Aor A⇒ page 268, fig. 253) out

of the housing and replace it with a new one.

Remove the lamp holder cover on the luggage compartment side and

close the side compartment.

Fig. 255 Removing the lamp

holder

Changing light bulbs in the lamp holder

–

Switch the ignition and all lights off.

Remove the side compartment cover by turning the locks in the direc-

tion of arrow ⇒ page 268, fig. 254.

–

Take out the cover of the lamp holder on the luggage compartment

side.

1

2

–

Take out the light bulbs of the tail light (arrow A and A) ⇒ fig. 255.

Press the catches in the direction of arrow and take out the lamp

holder.

–

Press the defective light bulb into the socket, turn to the left and

remove.

Press a new light bulb into the socket and turn the light bulb to the

right as far as the stop.

Change the light bulb for the parking light

–

Switch the ignition and all lights off.

Remove the side compartment cover by turning the locks in the direc-

tion of arrow ⇒ page 268, fig. 254.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

270 Fuses and light bulbs

Breakdown assistance for Your Skoda Octavia 4 Door Second Generation (2004-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals