2000-2004 Subaru Outback SUV Instruments and controls User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls for Your Subaru Outback SUV Second Generation (2000-2004)

3
Instruments and controls
Ignition switch 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key reminder chime 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition switch light 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key interlock release (AT vehicles only) 3-5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hazard warning flasher 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Meters and gauges 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Odometer/Trip meter 3-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tachometer 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outside temperature indicator (if equipped) 3-9. . . . . . . . . . . . . . . . . . . . . . .
Fuel gauge 3-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature gauge 3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning and indicator lights 3-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seatbelt warning light and chime 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SRS airbag system warning light 3-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECK ENGINE warning light/Malfunction
indicator lamp 3-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charge warning light 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oil pressure warning light 3-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AT OIL TEMPerature warning light (for AT vehicles) 3-14. . . . . . . . . . . . . .
ABS warning light 3-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VDC (Vehicle Dynamics Control) warning light
(if equipped) 3-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake system warning light 3-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Door open warning lights 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low fuel warning light 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front-wheel drive warning light (for AT vehicles
except GT and vehicle with VDC) 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VDC (Vehicle Dynamics Control) operation indicator
light (if equipped) 3-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VDC (Vehicle Dynamics Control) OFF indicator light
(if equipped) 3-18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security system status indicator light (if equipped) 3-18. . . . . . . . . . . . . .
Shift position indicator (for AT vehicles) 3-18. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn signal indicator lights 3-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High beam indicator light 3-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock 3-19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light control switch 3-20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Daytime running light system 3-21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turn signal lever 3-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Illumination brightness control 3-22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
Parking light switch 3-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fog light switch (if equipped) 3-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiper and washer 3-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield wiper and washer switches 3-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear window wiper and washer switch (if equipped) 3-28. . . . . . . . . . . . .
Rear window defogger switch 3-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield wiper deicer (if equipped) 3-30. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mirrors 3-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside mirror 3-31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outside mirrors 3-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tilt steering wheel 3-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Horn 3-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Instruments and controls
3-3
– CONTINUED –
Ignition switch
WARNING
Never turn the ignition switch to “LOCK” while the vehicle is be-
ing driven or towed because that will lock the steering wheel, pre-
venting steering control. And when the engine is turned off, it
takes a much greater effort than usual to steer.
The ignition switch has four positions: LOCK, ACC, ON and START.
HB4000CA
B LOCK
The key can only be inserted or removed in this position. The ignition
switch will lock the steering wheel when you remove the key.
If turning the key is difficult, turn the steering wheel slightly to the right
and left as you turn the key.
3-4
n Automatic transmission vehicles
HB2032CAHB4016BA
The key can be turned from “ACC” to “LOCK” only when the selector
lever is in the “P” position.
n Manual transmission vehicles
OM-H0144
The key can be turned from “ACC” to “LOCK” only when the key is
pushed in while turning it.
B ACC
In this position the electrical accessories (radio, accessory power
socket, etc.) can be used.
B ON
This is the normal operating position after the engine is started.
3
Instruments and controls
3-5
– CONTINUED –
B START
CAUTION
Do not turn the ignition switch to the “START” position while the
engine is running.
The engine is started in this position. The starter cranks the engine to
start it. When the key is released (after the engine has started), the
key automatically returns to the “ON” position.
J Key reminder chime
The reminder chime sounds when the driver’s door opens and the key is
in the “LOCK” or “ACC” positions. The chime stops when the key is re-
moved from the ignition switch.
J Ignition switch light
For easy access to the ignition switch in the dark, the ignition switch light
comes on when driver’s door is opened. The light remains on for 10 se-
conds and goes out after driver’s door is closed or if the key is turned to
the “ON” position.
J Key interlock release (AT vehicles only)
If the key can not be turned to the “LOCK” position even when the selec-
tor lever is in the “P” position:
HB3011BA
3-6
OM-H0146HB3012BA
1. Take out the screwdriver from the tool bag.
2. Remove the cover under the steering column using a phillips
screwdriver.
3. Turn the ignition key while pressing the key interlock release lever.
Take your vehicle to the nearest SUBARU dealer immediately to have
the key interlock system repaired.
3
Instruments and controls
3-7
– CONTINUED –
Hazard warning flasher
HB8002BA
The hazard warning flasher is used to warn other drivers when you have
to park your vehicle under emergency conditions. The hazard warning
flasher works with the ignition switch in any position.
To turn on the hazard warning flasher, push the hazard warning button
on the instrument panel. To turn off the flasher, push the button again.
NOTE
When the hazard warning flasher is on, the turn signals do not work.
Meters and gauges
J Speedometer
The speedometer shows the vehicle speed.
J Odometer/Trip meter
CAUTION
To ensure safety, do not attempt to change the function of the in-
dicator during driving, as an accident could result.
3-8
HB3015BB
B Odometer
The odometer shows the total distance that the vehicle has been driv-
en.
B Double trip meter
The trip meter shows the distance that the vehicle has been driven
since you last set it to zero.
To change the mode indication, briefly push the knob.
Each press of the knob changes the function alternately.
A trip meter B trip meter
To set the trip meter to zero, select either the A trip or B trip meter and
push the knob and keep it pushed for more than 1 second.
NOTE
If the connection between the combination meter and battery is bro-
ken for any reason such as vehicle maintenance or fuse replace-
ment, the data recorded on the trip meter will be lost.
3
Instruments and controls
3-9
– CONTINUED –
J Tachometer
CAUTION
Do not operate the engine with the pointer of the tachometer in
the red zone. In this range, fuel injection will be cut by the engine
control module to protect the engine from overrevving. The
engine will resume running normally after the engine speed is
reduced below the red zone.
The tachometer shows the engine speed in thousands of revolutions per
minute.
J Outside temperature indicator (if equipped)
The outside temperature indicator shows the outside temperature in a
range from –22°F to 122°F (–30°C to 50°C).
The indicator can give a false reading under any of the following condi-
tions:
D When there is too much sun.
D During idling; while running at low speeds in a traffic jam; when the
engine is restarted immediately following a shutdown.
D When the actual outside temperature falls outside the specified indi-
cator range.
For vehicles with an automatic climate control, outside temperature
can be displayed on the climate control display panel. Refer to the
“Automatic climate control system” in chapter 4.
J Fuel gauge
The fuel gauge shows the approximate amount of fuel remaining in the
tank.
The gauge does not return to “E” even though the ignition switch is in the
“ACC” or “LOCK” position.
The gauge may move slightly during braking, turning or acceleration due
to fuel level movement in the tank.
3-10
J Temperature gauge
CAUTION
If the pointer exceeds the normal operating range, safely stop the
vehicle as soon as possible.
See “In case of emergency” in chapter 9.
HB2012BB
The temperature gauge shows engine coolant temperature when the
ignition switch is in the “ON” position.
The coolant temperature will vary in accordance with the outside temper-
ature and driving conditions.
We recommend that you drive moderately until the pointer of the temper-
ature gauge reaches near the middle of the range. Engine operation is
optimum with the engine coolant at this temperature range and high rev-
ving operation when the engine is not warmed up enough should be
avoided.
Warning and indicator lights
Several of the warning and indicator lights come on momentarily and
then go out when the ignition switch is initially turned to the “ON” posi-
tion. This permits checking the operation of the bulbs.
Apply the parking brake and turn the ignition switch to the “ON” position.
The following lights come on:
3
Instruments and controls
3-11
– CONTINUED –
Seatbelt warning light
SRS airbag system warning light
CHECK ENGINE warning light / Malfunction indicator lamp
Charge warning light
Oil pressure warning light
AT OIL temperature warning light (AT vehicles)
ABS warning light
VDC warning light (if equipped)
VDC operation indicator light (if equipped)
VDC OFF indicator light (if equipped)
Brake system warning light
If any lights fail to come on, it indicates a burned-out bulb or a malfunc-
tion of the corresponding system.
Consult your authorized SUBARU dealer for repair.
J Seatbelt warning light and chime
When the ignition switch is turned to the “ON” position, the seatbelt
warning light will come on and the reminder chime will sound for about
six seconds to remind the driver to fasten the seatbelt.
The seatbelt warning light remains on for about six seconds and turns off
automatically after six seconds.
The seatbelt reminder chime will turn off when the driver’s side seatbelt is
buckled or it will turn off automatically after six seconds.
J SRS airbag system warning light
AIRBAG
When the ignition switch is turned to the “ON” position, the SRS airbag
system warning light will come on for about six seconds and go out. This
shows the SRS frontal airbag and SRS side airbag (if equipped) and
seatbelt pretensioners are in normal operation.
If this light comes on while driving or remains illuminated even after a
period of about 6 seconds from when the ignition has been turned on, it
may indicate that the SRS frontal airbag system or SRS side airbag sys-
tem (if equipped) or seatbelt pretensioner system is not working proper-
ly. Contact your nearest SUBARU dealer immediately.
3-12
J CHECK ENGINE warning light/Malfunction
indicator lamp
CAUTION
If the CHECK ENGINE light comes on while you are driving, have
your vehicle checked/repaired by your SUBARU dealer as soon
as possible. Continued vehicle operation without having the
emission control system checked and repaired as necessary
could cause serious damage, which may not be covered by your
vehicle’s warranty.
If this light comes on steadily or blinks while the engine is running, it may
indicate that there is a problem or potential problem somewhere in the
emission control system.
B If the light comes on steadily:
If the light comes on steadily while driving or does not go out after the
engine starts, an emission control system malfunction has been de-
tected.
You should have your vehicle checked by an authorized SUBARU
dealer immediately.
NOTE
This light also comes on when the fuel filler cap is not tightened
until it clicks.
If you have recently refueled your vehicle, the cause of the CHECK
ENGINE warning light/malfunction indicator lamp coming on could be a
loose or missing fuel filler cap. Remove the cap and retighten it until it
clicks. Make sure nothing is interfering with the sealing of the cap.
Tightening the cap will not make the CHECK ENGINE warning light
turn off immediately. It may take several driving trips. If the light does
not go out, take your vehicle to your authorized SUBARU dealer
immediately.
B If the light is blinking:
If the light is blinking while driving, an engine misfire condition has
been detected which may damage the emission control system.
3
Instruments and controls
3-13
– CONTINUED –
To prevent serious damage to the emission control system, you
should do the following:
D Reduce vehicle speed.
D Avoid hard acceleration.
D Avoid steep uphill grades.
D Reduce the amount of cargo, if possible.
D Stop towing a trailer as soon as possible.
The CHECK ENGINE warning light may stop blinking and come on
steadily after several driving trips. You should have your vehicle
checked by an authorized SUBARU dealer immediately.
J Charge warning light
If this light comes on when the engine is running, it may indicate that the
charging system is not working properly.
If the light comes on while driving or does not go out after the engine
starts, stop the engine at the first safe opportunity and check the alterna-
tor belt. If the belt is loose, broken or if the belt is in good condition but
the light remains on, contact your nearest SUBARU dealer immediately.
J Oil pressure warning light
CAUTION
Do not operate the engine with the oil pressure warning light on.
This may cause serious engine damage.
If this light comes on when the engine is running, it may indicate that the
engine oil pressure is low and the lubricating system is not working prop-
erly.
If the light comes on while driving or does not go out after the engine
starts, stop the engine at the first safe opportunity and check the engine
oil level. If the oil level is low, add oil immediately. If the engine oil is at
the proper level but the light remains on, contact your nearest SUBARU
dealer immediately.
3-14
J AT OIL TEMPerature warning light
(for AT vehicles)
If this light comes on when the engine is running, it may indicate that the
automatic transmission fluid temperature is too hot.
If the light comes on while driving, it is unnecessary to stop the vehicle,
but avoid driving up steep grades or in stop and go traffic.
B Automatic transmission control system warning
If the light flashes after the engine starts, it may indicate that the auto-
matic transmission control system is not working properly. Contact
your nearest SUBARU dealer for service immediately.
J ABS warning light
The ABS warning light comes on when the ignition switch is turned to the
“ON” position and goes out after about two seconds.
This is an indication that the ABS system is working properly.
CAUTION
If the warning light behaves as follows, the ABS system may not
work properly.
When the warning light is on, the ABS function shuts down; how-
ever, the conventional brake system continues to operate normal-
ly.
D The warning light does not come on when the ignition switch
is turned to the “ON” position.
D The warning light comes on when the ignition switch is turned
to the “ON” position, but it does not go out even when the vehicle
speed exceeds approximately 8 mph (12 km/h).
D The warning light comes on during driving.
If these occur, have the ABS system repaired at the first available
opportunity by your SUBARU dealer.
NOTE
If the warning light behavior is as shown below, the ABS system
may be considered normal.
(U.S.)
(Canada)
3
Instruments and controls
3-15
– CONTINUED –
D The warning light comes on right after the engine is started but
goes out immediately, remaining off.
D The warning light remains on after the engine has been started,
but it goes out when the vehicle speed reaches about 8 mph (12
km/h).
D The warning light comes on during driving, but it goes out
immediately and remains off.
When driving with an insufficient battery voltage such as when the en-
gine is jump started, the ABS warning light may come on. This is due to
the low battery voltage and does not indicate a malfunction. When the
battery becomes fully charged, the light will go out.
J VDC (Vehicle Dynamics Control) warning light
(if equipped)
This warning light comes on when the ignition switch is turned to the
“ON” position and goes out after the engine has started. It indicates that
the VDC system is operational.
The VDC system is probably inoperative under any of the following
conditions. Immediately have your vehicle checked at a SUBARU dealer.
D The VDC warning light does not come on when the ignition switch is
turned to the “ON” position.
D The VDC warning light remains on after the engine has started and
stays lit even when the vehicle speed reaches about 8 mph (12 km/h).
D The VDC warning light comes on while the vehicle is running.
D If the electrical circuit of the VDC system itself becomes faulty, the
VDC warning light only comes on. At this time, the ABS (Anti-lock Brake
System) remains fully operational.
D The warning light comes on when the electronic control system of the
ABS/VDC system becomes faulty.
The VDC system provides its ABS control through the electrical circuit of
the ABS system. Accordingly, if the ABS is inoperative, the VDC system
also becomes unable to provide ABS control. As a result, the VDC sys-
tem becomes inoperative, causing the VDC warning light to come on.
Though both the VDC and ABS systems are inoperative in this case, the
ordinary functions of the brake system are still available. You will be safe
3-16
while driving with this condition, but you should have your vehicle
checked at a SUBARU dealer as soon as possible.
NOTE
If the warning light behavior is as shown below, the VDC system
may be considered normal.
D The warning light comes on right after the engine is started but
goes out immediately, remaining off.
D The warning light remains on after the engine has been started,
but it goes out when the vehicle speed reaches 8 mph about (12
km/h).
D The warning light comes on during driving, but it goes out im-
mediately and remains off.
J Brake system warning light
WARNING
D Driving with the brake system warning light on is dangerous.
This indicates your brake system may not be working properly. If
the light remains on, have the brakes inspected by a SUBARU
dealer immediately.
D If at all in doubt about whether the brakes are operating prop-
erly, do not drive the vehicle. Have your vehicle towed to the
nearest SUBARU dealer for repair.
This light has the following two functions:
B Parking brake warning
The light comes on with the parking brake applied while the ignition
switch is in the “ON” position. It goes out when the parking brake is
fully released.
B Brake fluid level warning
This light comes on when the brake fluid level has dropped to near
the “MIN” level of the brake fluid reservoir with the ignition switch in
the “ON” position and with the parking brake fully released.
If the brake system warning light should come on while driving (with
the parking brake fully released and with the ignition switch posi-
(U.S.)
(Canada)
3
Instruments and controls
3-17
– CONTINUED –
tioned in “ON”), it could be an indication of leaking of brake fluid or
worn brake pads. Have your vehicle checked by a SUBARU dealer
immediately.
J Door open warning lights
The specific door open warning light comes on if any door or the rear
gate is not fully closed.
Always make sure this light is out before you start to drive.
J Low fuel warning light
The low fuel warning light comes on when the tank is nearly empty about
2.6 U.S. gal. (10.0 liters, or 2.2 Imp. gal.). It only operates when the igni-
tion switch is in the “ON” position.
NOTE
This light does not go out unless the tank is replenished up to an
internal fuel quantity of about 3.7 U.S. gal. (14 liters, 3.1 Imp. gal.).
J Front-wheel drive warning light (for AT vehicles
except GT and vehicle with VDC)
This light comes on when All Wheel Drive is disengaged and the drive
mechanism is switched to Front Wheel Drive for maintenance or similar
purposes.
J VDC (Vehicle Dynamics Control) operation
indicator light (if equipped)
This light comes on when the ignition switch is ON and goes out about 2
seconds later.
It blinks when the skid suppression function is activated. It illuminates
when only the traction control function is operating.
The VDC system is probably faulty under any of the following conditions.
Have your vehicle checked at a SUBARU dealer immediately.
D The light does not come on when the ignition switch is turned to the
“ON” position.
D The light does not go out even after a period of about 2 seconds after
3-18
the ignition switch has been turned to the “ON” position.
J VDC (Vehicle Dynamics Control) OFF indicator
light (if equipped)
D This indicator light comes on when the ignition switch is turned ON
and goes out about 6 seconds after the engine has started.
D It comes on when the VDC system is deactivated (by operating “VDC
OFF” switch or in the standby state).
NOTE
D The light may stay on for a while after the engine has been
started, especially in cold weather. This does not indicate the exis-
tence of a problem. The light should go out as soon as the engine
has warmed up.
D The “VDC OFF” indicator light comes on when the engine has de-
veloped a problem and the CHECK ENGINE warning light is on.
The VDC system is probably faulty under any of the following conditions.
Have your vehicle checked at a SUBARU dealer as soon as possible.
D The VDC OFF indicator light does not come on when the ignition
switch is turned to the “ON” position.
D The light does not go out even after several minutes have passed (the
engine has warmed up) after the engine has been started.
J Security system status indicator light
(if equipped)
This light is found at the bottom center of the combination meter panel.
On vehicles equipped with a security system, it blinks to show the driver
the operational status of the security system. For detailed information, re-
fer to the “Security system” in Chapter 2.
J Shift position indicator (for AT vehicles)
This indicator shows the position of the shift lever.
If the transmission has a Sport Shift mode, the position of the shift lever is
shown by another indicator during Sport Shift mode operation. For de-
tails, refer to Chapter 7, “Automatic transmission”.
3
Instruments and controls
3-19
– CONTINUED –
J Turn signal indicator lights
These lights show the operation of the turn signal or lane change signal.
If the indicator lights do not blink or blink rapidly, the turn signal bulb
may be burned out. Replace the bulb as soon as possible. Refer to the
“Replacing bulbs” section in chapter 11.
J High beam indicator light
This light shows that the headlights are in the high beam mode.
This indicator light also comes on when the headlight flasher is operated.
Clock
HB2013BA
To set the time, turn the setting knob clockwise to advance and counter-
clockwise to retard the time.
3-20
Light control switch
WARNING
To prevent battery discharge resulting from accidentally leaving
your lights on when your vehicle is parked, the light switch oper-
ates only when the ignition switch is in the “ON” position. In any
other position, the vehicle’s lights will be out.
If you park your vehicle on a roadside at night, use the hazard
warning flasher to alert the other drivers.
HB2014BBHB2007BA
The light switch operates only when the ignition switch is in the “ON”
position.
B Headlights
To turn on the headlights, turn the knob on the end of the turn signal
lever.
first position
Parking lights, instrument panel illumination, tail lights and license
plate light are on.
second position
Headlights, parking lights, instrument panel illumination, tail lights,
and license plate light are on.
3
Instruments and controls
3-21
– CONTINUED –
B High/low beam change (dimmer)
To change from low beam to high beam, push the turn signal lever
forward. When the headlights are on high beam, the high beam indi-
cator light “a” on the instrument panel is also on.
To switch back to low beam, pull the lever back to the detent position.
B Headlight flasher
CAUTION
Do not hold the lever in the flashing position for more than just a
few seconds.
To flash the headlights, pull the lever toward you and then release it.
The high beam will stay on for as long as you hold the lever. The
headlight flasher works even though the lighting switch is in the “OFF”
position.
When the headlights are on high beam, the high beam indicator light
“a” on the instrument panel also comes on.
J Daytime running light system
WARNING
The tail lights, parking lights, and side marker lights are not
turned on by the daytime running light system. The light switch
must always be turned to the “a” position when it is dark out-
side.
The low beam headlights will automatically come on at reduced bright-
ness when the engine has started, under the following conditions:
D The parking brake is fully released.
D The light switch is in the “OFF” or “p” position.
3-22
Turn signal lever
HB2015BB
Right turn
Left turn
To activate the right turn signal, push the turn signal lever up. To activate
the left turn signal, push the turn signal lever down. When the turn is fin-
ished, the lever will return automatically. If the lever does not return after
cornering, return the lever to the neutral position by hand.
To signal a lane change, push the turn signal lever up or down slightly
and hold it during the lane change. The turn signal indicator lights will
flash in the direction of the turn or lane change. The lever will return auto-
matically to the neutral position when you release it.
Illumination brightness control
HB2017BB
3
Instruments and controls
3-23
– CONTINUED –
When the lighting switch is in the “p” or “a” position, you can adjust
brightness of the instrument panel illumination for better visibility.
To brighten, turn the control dial counterclockwise.
To darken, turn the control dial clockwise.
Parking light switch
HB2018BA
The parking light switch operates regardless of the ignition switch posi-
tion.
By pushing the front end of this switch, following lights will come on.
– Parking lights
– Front and rear side marker lights
– Tail lights
– License plate lights
To turn off, push the rear end of the parking light switch.
Avoid leaving these lights on for a long time because that will run down
the battery.
3-24
Fog light switch (if equipped)
The fog lights operate only when the headlights are on low beam. Push
the fog light switch to turn the fog lights on.
Press the switch again to turn them off.
HB2025BB
The indicator light located on the switch will illuminate when the fog
lights are on.
Wiper and washer
WARNING
In freezing weather, do not use the windshield washer until the
windshield is sufficiently warmed by the defroster.
Otherwise the washer fluid can freeze on the windshield, blocking
your view.
CAUTION
D Do not operate the washer continuously for more than ten se-
conds, or when the washer fluid tank is empty. This may cause
overheating of the washer motor. Check the washer fluid level fre-
quently, such as at fuel stops.
3
Instruments and controls
3-25
– CONTINUED –
D Do not operate the wipers when the windshield or rear window
is dry. This may scratch the glass, damage the wiper blades and
cause the wiper motor to burn out. Before operating the wiper on
a dry windshield or rear window, always use the windshield
washer.
D In freezing weather, be sure that the wiper blades are not fro-
zen to the windshield or rear window before switching on the
wipers. Attempting to operate the wiper with the blades frozen to
the window glass could cause not only the wiper blades to be
damaged but also the wiper motor to burn out. If the wiper blade
is frozen to the window glass, be sure to operate the defroster,
wiper deicer (if equipped) or rear window defogger before turning
on the wiper.
D If the wipers stop during operation because of ice or some oth-
er obstruction on the window, the wiper motor could burn out
even if the wiper switch is turned off. If this occurs, promptly stop
the vehicle in a safe place, turn the ignition switch to the “LOCK”
position and clean the window glass to allow proper wiper opera-
tion.
D Use clean water if windshield washer fluid is unavailable. In
areas where water freezes in winter, use SUBARU Windshield
Washer Fluid or the equivalent. (See “Windshield washer fluid”
section in chapter 11.)
Also, when driving the vehicle when there are freezing tempera-
tures, use non-freezing type wiper blades.
D Do not clean the wiper blades with gasoline or a solvent, such
as paint thinner or benzene. This will cause deterioration of the
wiper blades.
NOTE
D The wiper operates only when the ignition switch is in the “ON”
or “ACC” position.
D Clean your wiper blades and window glass periodically with a
washer solution to prevent streaking, and to remove accumulations
of road salt or road film. Keep the washer button depressed at least
for 1 second so that washer solution will be sprinkled all over the
3-26
windshield or rear window.
D Grease, wax, insects or other material on the windshield or the
wiper blades results in jerky wiper operation and streaking on the
glass. If you cannot remove those streaks after operating the
washer or if the wiper operation is jerky, clean the outer surface of
the windshield or rear window and the wiper blades using a sponge
or soft cloth with a neutral detergent or mild-abrasive cleaner. After
cleaning, rinse the window glass and wiper blades with clean water.
The glass is clean if no beads form on the glass when you rinse with
water.
D If you cannot eliminate the streaking even after following this pro-
cedure, replace the wiper blades with new ones. Refer to the “Wiper
blade replacement” section (chapter 11) for replacement instruc-
tions.
J Windshield wiper and washer switches
B Windshield wipers
HB2019BB
To turn the wipers on, push the wiper control lever down.
: Intermittent
LO : Low speed
HI : High speed
To turn the wipers off, return the lever to the “OFF” position.
3
Instruments and controls
3-27
– CONTINUED –
B Wiper intermittent time control (if equipped)
HB2023BA
When the wiper switch is in the “ ” position, turn the dial to adjust
the operating interval of the wiper.
The operating interval can be adjusted continuously from the shortest
interval to the longest.
Two click stop positions of the dial may help you to aim at your de-
sired interval.
B Mist (for a single wipe)
For a single wipe of the wipers, pull the lever toward you. The wipers
operate until you release the lever.
B Washer
HB2020BA
To wash the windshield, push the washer button at the end of the wip-
3-28
er control lever. The washer fluid sprays until you release the washer
button. The wipers operate while you push the button.
J Rear window wiper and washer switch (if equipped)
HB2021BC
B Rear wiper
The rear wiper offers intermittent operation only.
To turn the rear wiper on, turn the knob on the end of the wiper control
lever upward.
To turn the wiper off, return the knob on the end of the lever to the
“OFF” position.
B Washer
To wash the rear window while the rear wiper is operating, turn the
knob on the end of the wiper control lever upward to the “
” posi-
tion. The washer fluid sprays until you release the knob.
To wash the rear window when the rear wiper is not in use, turn the
knob on the end of the wiper control lever downward to the “
”
position. The washer fluid sprays and the wiper operates until you re-
lease the knob.
3
Instruments and controls
3-29
– CONTINUED –
Rear window defogger switch
CAUTION
D Do not use sharp instruments or window cleaner containing
abrasives to clean the inner surface of the rear window. They may
damage the conductors printed on the window.
D To prevent the battery from being discharged, do not operate
the defogger continuously for any longer than necessary.
The rear window defogger operates only when the ignition switch is in
the “ON” position.
The rear window defogger switch is located on the climate control panel.
The defogger will automatically shut off after about 15 minutes. If the win-
dow clears before that time, push the switch to turn it off. It also turns off
when the ignition switch is turned to the “ACC” or “LOCK” position. If
defrosting or defogging is desired when you restart your vehicle, you
have to push the switch to turn it on again.
B For vehicles with manual heating and air conditioning systems
HB5009BB
To turn on the defogger, push the switch. To turn it off, push the switch
again.
The indicator light located on the switch lights up while the rear win-
dow defogger is operating.
3-30
B For vehicles with automatic climate control
HB3016BB
To turn on the defogger, push the switch. To turn it off, push the switch
again.
The indicator light “u” lights up on the climate control display panel
while the rear window defogger is operating.
Windshield wiper deicer (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate the
windshield wiper deicer continuously for any longer than neces-
sary.
HB2027BB
3
Instruments and controls
3-31
– CONTINUED –
The windshield wiper deicer operates only when the ignition switch is in
the “ON” position.
Before turning on the windshield wiper deicer, remove any snow from the
windshield. To turn on the windshield wiper deicer, push the switch. The
indicator light located on the switch lights up while the windshield wiper
deicer is operating.
The windshield wiper deicer will automatically shut off after about 15 min-
utes. If the wiper blades have been deiced completely before that time,
push the switch to turn it off. It also turns off when the ignition switch is
turned to the “ACC” or “LOCK” position. If deicing is not complete when
you restart your vehicle, you have to push the switch to turn the deicer
on again.
Mirrors
Always check that the inside and outside mirrors are properly adjusted
before you start driving.
J Inside mirror
HB4003BB
The inside mirror has a day and night position. Pull the tab at the bottom
of the mirror toward you for the night position. Push it away for the day
position. The night position reduces glare from headlights.
3-32
B Auto-dimming mirror/compass (if equipped)
HB6019BB
The auto-dimming mirror/compass has an anti-glare feature which au-
tomatically reduces glare coming from headlights of vehicles behind
you. It also contains a built-in compass.
D By pressing and releasing the left button, the automatic dimming
function is toggled on or off. When the automatic dimming function is
on, the auto dimming indicator light (green) located to the right of the
button will illuminate.
D By pressing and releasing the right button, the compass display is
toggled on or off. When the compass is on, an illuminated compass
reading will appear in the lower part of the mirror.
Even with the mirror in anti-glare mode, the mirror surface turns bright
if the transmission is shifted into reverse. This is to ensure good rear-
ward visibility during reversing.
3
Instruments and controls
3-33
– CONTINUED –
n Photosensors
HB6020BA
The mirror has a photosensor attached on both the front and back
sides. If the glare from the headlights of vehicles behind you strikes
the mirror, these sensors detect it and make the reflection surface of
the mirror dimmer to help prevent you from being blinded. For this
reason, use care not to cover the sensors with stickers, or other simi-
lar items. Periodically wipe the sensors clean using a piece of dry soft
cotton cloth or an applicator.
n Compass calibration
1. For optimum calibration, switch off all nonessential electrical ac-
cessories (rear window defogger, heater/air conditioning system,
spotlight, etc.) and ensure all doors are shut.
2. Drive to an open, level area away from large metallic objects or
structures and make certain the ignition switch is in the “ON” position.
3. Press and hold the left button for 3 seconds then release, and the
compass will enter the calibration mode. “CAL” and direction will be
displayed.
4. Drive slowly in a circle until “CAL” disappears from the display
(about two or three circles).
5. The compass is now calibrated. Further calibration is not required.
The compass will automatically calibrate from this point forward.
3-34
n Compass zone adjustment
HB6021AB
1. The zone setting is factory preset to Zone 8. Refer to the “Com-
pass calibration zone” map shown above or one attached to the end
of this manual to verify that the compass zone setting is correct for
your geographical location.
2. Press and hold the right button for 3 seconds then release, and the
word “ZONE” will briefly appear and then the zone number will be dis-
played.
3. Press the right hand button repeatedly to cycle the display through
all possible zone settings. Stop cycling when the correct zone setting
for your location is displayed.
4. Releasing the button for 3 seconds will exit the zone setting mode.
J Outside mirrors
B Convex mirror (Passenger side)
WARNING
Objects look smaller in a convex mirror and farther away than
when viewed in a flat mirror. Do not use the convex mirror to
judge the distance of vehicles behind you when changing lanes.
Use the inside mirror (or glance backwards) to determine the
actual size and distance of objects that you view in convex mir-
ror.
3
Instruments and controls
3-35
– CONTINUED –
B Adjusting mirrors
To adjust the mirrors by hand, push where indicated by the arrows.
OM-H2737
B Remote control mirror switch (if equipped)
The remote control mirrors operate only when the ignition switch is in
the “ON” or “ACC” position.
HB4004BB
1. Press either end of the selection switch, “L” for the left, “R” for the
right.
2. Move the direction control switch in the direction you want to move
the mirror.
3. Return the selection switch to the neutral position to prevent
unintentional operation.
The mirrors can also be adjusted manually.
3-36
B Outside mirror defogger (if equipped)
CAUTION
To prevent the battery from being discharged, do not operate the
defogger continuously for any longer than necessary.
The outside mirror defogger operates only when the ignition switch is
in the “ON” or “ACC” position.
HB4004CB
To turn on the outside mirror defogger, push the switch while the en-
gine is running.
The indicator light located on the switch will come on when the out-
side mirror defogger heater in operation.
To turn it off, push the switch again.
Tilt steering wheel
WARNING
Do not adjust the steering wheel tilt position while driving. This
may cause loss of vehicle control and result in personal injury.
3
Instruments and controls
3-37
– CONTINUED –
HB4002BA
1. Adjust the seat position. Refer to the “Front seat” section (chapter 1).
2. Pull the tilt lock lever down.
3. Move the steering wheel to the desired level.
4. Push the lever up to lock the steering wheel in place.
5. Make sure that the steering wheel is securely locked by moving it up
and down.
Horn
OM-H0440
To sound the horn, push the horn pad.

Related Topics

Ignition switch Key reminder chime Ignition switch light Key interlock release (AT vehicles only) Hazard warning flasher Meters and gauges Speedometer Odometer/Trip meter Tachometer Outside temperature indicator Fuel gauge Temperature gauge Warning and indicator lights Clock Light control switch Daytime running light system Turn signal lever Illumination brightness control Parking light switch Fog light switch Wiper and washer Windshield wiper and washer switches Rear window wiper and washer switch Rear window defogger switch Windshield wiper deicer Mirrors Inside mirror Outside mirrors Tilt steering wheel Horn

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot