Get Instruments and controls -> Mirrors Guide for Subaru Outback SUV Fourth Generation (2010-2014)

3-50 Instruments and controls

necessary.

. Do not use sharp instruments or

window cleaner containing abra-

sives to clean the inner surface

of the rear window. They may

damage the conductors printed

on the window.

NOTE

. Turn on the defogger and deicer

system if the wipers are frozen to the

windshield.

. If the windshield is covered with

snow, remove the snow so that the

windshield wiper deicer works effec-

tively.

. While the defogger and deicer sys-

tem is in the continuous operation

mode, if the vehicle speed remains at

9 mph (15 km/h) or lower for 15

minutes, the windshield wiper deicer

automatically stops operating, though

the rear window defogger and outside

mirror defogger maintain continuous

operation in this condition.

. While the defogger and deicer sys-

tem is in the continuous operation

mode, if the battery volta ge dro ps

below the permissible level, continu-

ous operation of t he defogger and

deicer system is canceled and the

system stops operating.

Mirrors

Always check that the inside and outside

mirrors are properly adjusted before you

start driving.

& Type A inside mirror (if

equipped)

The mirror has a day and night position.

Pull the tab at the bottom of the mirror

toward you for the night position. Push it

away for the day position. The night

position reduces glare from headlights.

& Type B inside mirror (if

equipped)

1) Rear view image display

2) HomeLink

button 1

3) HomeLink

button 2

4) Function indicator

5) HomeLink

button 3

6) Photosensor

7) Power on button

8) Power off button

The mirror has the following features.

. Auto-dimming fun ction for anti-glare

capability

. Rear view image display

. HomeLink

Wireless Control System

Using the powe r on butto n, you can

display the various functions of the rear

view image display based on how long

you press the buttons.

Gear

position

Period of

time button

is pressed

Function

displayed

Except

R (reverse)

Briefly

Auto-dimming

function ON/OFF*

R (reverse) Briefly

Rear view image

display: ON/OFF*

mode

6 to 12

seconds

Enter the lan-

guage selection

mode

12 to 15

seconds

Rear view image

display: opera-

tional/non-opera-

tional mode

*: The setting returns to “ON” as a default

setting every time the ignition switch is turned to

the “OFF” position.

! Auto-dimming function

The auto-dimming function is an anti-glare

capability which automatically reduces

glare coming from headlights of vehicles

behind you.

By pressing the power on button, the auto-

dimming function is turned on. By pressing

the power off button, the auto-dimming

function is turned off. When the auto-

dimming fun ction is on, the function

indicator will illuminate in green.

Even with the mirror in anti-glare mode,

the mirror surface turns bright if the shift

lever/select lever is shifted into the “R”

(reverse) position. This is to ensure good

rearward visibility during reversing.

The mirror has a photosensor attached on

both the front and back sides. During

nighttime driving, these sensors detect

distracting glare from vehicle headlights

behind you and automatically dim the

mirror to eliminate glare and preserve

your vision. For this reason, use care not

to cover the sensors with stickers, or other

similar items. Periodically wipe the sen-

sors clean using a piece of dry soft cotton

cloth or an applicator.

NOTE

When cleaning the mirror, use a paper

towel or similar item dampened with

Instruments and controls 3-51

– CONTINUED –

3-52 Instruments and controls

glass clea ner. Do not spray glass

cleaner directly on the mirror surface.

By doing so, the sprayed glass cleaner

could enter the inside of the mirror

housing. That may cause a malfunction

in the mirror.

! Rear view image display

When the ignition switch is in the “ON”

position and the shift lever/select lever is

in the “R” (reverse) position, the rear view

camera automatically displays the rear

view image behind the vehicle on the

inside mirror.

Also, the following help lines are indicated

as a guide to help you realize the actual

distance from the display.

1) Vehicle width line (oblique vertical line)

2) Approx. 10 feet (3 m) from the bumper

(green horizontal line)

3) Approx. 6.5 feet (2 m) from the bumper

(green horizontal line)

4) Approx. 3 feet (1 m) from the bumper

(yellow horizontal line)

5) Approx. 1.5 feet (0.5 m) from the bumper

(red horizontal line)

By pressing the power on button while the

shift lever/select lever is in the “R”

(reverse) position, the rear view image

display turns to the on mode. By pressing

the power off button while the shift lever/

select lever is in the “R” (reverse) position,

the rear view image display turns to the off

mode.

Once the rear view image display is set to

the off mode, the display stays in the off

mode, with the function indicator in or-

ange, every time the shift lever/select

lever is shifted into the “R” (reverse)

position.

If th e ignit ion switch is turned to the

”LOCK”/OFF” position, the display setting

returns to the on mode as a default setting

the next time the ignition switch is turned

to the “ON” position.

! Language mode change

The language mode of the captions on the

rear view image display is selectable in

English or French in the following ways.

1. Press and hold the power on button for

6 to 12 seconds while the shift lever/select

lever is in the “R” (reverse) position, and

then release it. The display will enter the

language selection mode.

2. Briefly press the power on button to

toggle the capti ons on the display in

English or French.

3. By releasing the power on button for 5

seconds, the display blinks one time to

show that the language mode is selected.

! Non-operational mode

The rear view image display can be set as

non-operational. After setting the display

to the non-operational mode, the display

does not show the rear view image even if

the ignition switch is reset (turning the

ignition switch to the “ON” position after

turning it to the “LOCK”/“ OFF ” position).

To set the display to the non-operational

mode, press and hold the power on button

for 12 to 15 seconds while the shift lever/

select lever is in the “R” (reverse) position,

and then release it. The display is now in

the non-operational mode. After the dis-

play has been set to the non-operational

mode, the function indicator will illuminate

in orange while the shift lever/select lever

is in the “R” (reverse) position.

To return the display to the operational

mode, press and hold the power on button

for 12 to 15 seconds again.

F or precautions about the rear view

camera and the rear view image, refer to

“Rear view camera” F6-18.

! HomeLink

Wireless Control Sys-

tem

The HomeLink

Wireless Control System

can be used to activate remote control

devices such as gate operators, garage

door openers, door locks, home lighting

and security systems.

There are three HomeLink

buttons on the

mirror, each of which can be programmed

for operation of one desired device. For

details on the device types which can be

operated by this system, consult the

HomeLink

website at:

www.homelink.com or call 1-800-355-

3515.

Note the following information about this

system.

If your vehicle is equipped with the

HomeLink

Wireless Control System, it

complies with Part 15 of the Federal

Communi cati ons Commissi on Rules in

the U.S. and the RSS-210 of Industry

Canada in Canada. Its operation is subject

to the following two conditions:

(1) this device may not cause harmful

interference, and (2) this device must

accept any interference received, includ-

ing interference that may cause undesired

operation.

Changes and modifications to this system

by anyone other than an authorized

service facility could void authorization to

use this equipment.

HomeLink

and the HomeLink

house are

registered trademarks of Johnson Con-

trols, Inc.

WARNING

. W h e n p r o g r a m m i n g t h e

HomeLink

Wireless Control Sys-

tem, you may be o perating a

garage door opener or other

device. Make sure that people

and objects are out of the way

of the garage door or other

device to prevent potential harm

or damage.

. Do not use the HomeLink

Wire-

less Control System with a gar-

age door opener that lacks the

safety stop and reverse feature

as required by applicable safety

standards. A garage door opener

which cannot detect an object,

signaling the door to stop and

revers e, does not meet these

safety standards. Using a garage

door opener without these fea-

tures increases risk of serious

injury or death. For more infor-

mation, consult the HomeLink

website at or

call 1-800-355-3515.

CAUTION

When programming the HomeLink

Wireless Control System to operate

a garage door opener or an entrance

gate, unplug the device’s motor

from the outlet during programming

to prevent motor burnout.

Instruments and controls 3-53

– CONTINUED –

3-54 Instruments and controls

NOTE

. After programming your HomeLink

Wireless Control System for the de-

sired devices, retain the h and-held

transmitters for further programming

or device testing in the event of a

problem.

. It is recommended that you insert a

new battery in the hand-held transmit-

ter of a device to ensure correct

programming.

! Garage door opener programming in

the U.S.A.

NOTE

When pro gram ming the HomeLink

Wireless Control System for a garage

door opener, it is suggested that you

park the vehicle outside the garage.

1. Unplug the motor of the garage door

opener from the outlet.

NOTE

If any of the HomeLink

buttons are

already programmed for other devices,

skip step 2 because it clears the

memory of all three buttons.

1) HomeLink

button 1

2) HomeLink

button 2

3) HomeLink

button 3

2. Press and hold the two outer

HomeLink

buttons (button 1 and button

3) until the indicator light begins to flash

(after approximately 20 seconds). Then

release both buttons.

3. Hold the en d of the ga rage door

opener’s hand-held transmitter between

1 and 3 inches (25 and 76 mm) away from

the HomeLink

button you wish to pro-

gram.

4. Simultaneously press and hold both

the hand-held transmitter button and the

desired HomeLink

button. DO NOT re-

lease the buttons until step 5 has been

completed.

NOTE

Some gate operators and garage door

openers may require you to replace

this programming step 4 with proce-

dures in “Programming for entrance

gates and gar age door openers in

Canada” F3-55.

5. Hold down both buttons until the

Hom eLink

indicator light f lashes, first

slowly then rapidly. When the indicator

light flashes rapidly, both buttons may be

released. (The rapidly flashing light indi-

cates successful programming of the new

frequency signal.)

6. Press and hold the programmed but-

ton and check the HomeLink

indicator

light. If the indicator light stays on con-

tinuously, your garage door should acti-

vate and the programming is completed.

If the indicator light flashes rapidly for 2

seconds and then stays on continuously,

your garage door opener may be pro-

tected by a rolling code feature. In this

case you need to perform the additional

steps that are described in “Programming

rolling-code-protected garage door open-

ers in the U.S.A.” F3-55.

! Programming rolling-code-protected

garage door openers in the U.S.A.

If your garage door opener has a rolling

code feature, program the HomeLink

Wireless Control System for it by following

steps 1 through 5 in “Garage door opener

programming in the U.S.A.” F3-54. Then

continue with the following steps.

NOTE

The assistance of a second person

may make the programming quicker

and easier.

1. Locate the tr aining b utt on on the

garage door opener moto r head u nit .

The exact location and color of the button

may vary by brand of garage door opener.

If it is difficult to locate the training button,

refer to your garage door opener’s instruc-

tion manual.

1) Training button

2. Press the training button on the

garage door opener motor head uni t

(which activates the “training light” on the

unit). Proceed to step 3 within 30 seconds.

3. Inside the vehicle, firmly press, hold for

2 seconds and release the HomeLink

button that was programmed in the pre-

vious section. Press and release the

button a second time to complete the

programming procedure.

NOTE

Some garage door openers may re-

quire you to do the above press-hold-

release sequence a third time to com-

plete the programming.

4. The garage door opener should now

recognize the HomeLink

Wireless Control

System and your garage door opener

should activate when the HomeLink

button is pressed.

! Programming for entrance gates and

garage door openers in Canada

1. Unplug the motor of the entrance gate

or garage door opener from the outlet.

NOTE

If any of the HomeLink

buttons are

already programmed for other devices,

skip step 2 because it clea rs the

memory of all three buttons.

Instruments and controls 3-55

– CONTINUED –

3-56 Instruments and controls

1) HomeLink

button 1

2) HomeLink

button 2

3) HomeLink

button 3

2. Press and hold the two outer

HomeLink

buttons (button 1 and button

3) until the HomeLink

indicator light

begins to flash (after approximately 20

seconds). Then release both buttons.

3. Hold the end of the entrance gate’s/

garage door opener’s hand-held transmit-

ter between 1 and 3 inches (25 and 76

mm) away from the HomeLink

button you

wish to program.

4. Press and hold the desired HomeLink

button.

5. Press and release (“cycle”) the hand-

held transmitter button every 2 seconds

until step 6 is complete.

6. When the indicator light flashes slowly

and then rapidly after several seconds,

release both buttons.

7. Plug the motor of the entrance gate/

garage door opener to the outlet.

8. Test your entrance gate/garage door

opener by pressing the programm ed

HomeLink

button.

! Operating the HomeLink

Wireless

Control System

Once programmed, the HomeLink

Wire-

le ss Control System can be used to

remote-control the devices to which its

buttons are programmed. To activate a

device, simply press the appropriate but-

ton. The indicator light illuminates, indicat-

ing that the signal is being transmitted.

! Programming other devices

To program other devices such as door

locks, home lighting and security systems,

contact HomeLink

at www.

or call 1-800-355-3515.

! Reprogramming a single HomeLink

button

1. Press and hold the HomeLink

button

you wish to reprogram. DO NOT release

the button until step 4 has been com-

pleted.

2. When the HomeLink

indicator light

begins to flash slowly (after approximately

20 seconds), position the hand-held trans-

mitter of the device between 1 to 3 inches

(25 to 76 mm) away from the HomeLink

button you wish to program.

3. Press and hold the hand-held trans-

mitter button. The HomeLink

indicator

light will flash, first slowly and then rapidly.

4. When the indicator light begins to flash

rapidly, release both buttons.

The programming for the previous device

is now erased and the new device can be

operated by pressing t he HomeLink

button.

! Erasing HomeLink

button memory

NOTE

. Performing this procedure erases

the memory of all the preprogrammed

buttons simultaneously. The memory

of individual buttons cannot be erased.

. It is recommended that upon the

sale of the vehicle, the memory of all

programmed HomeLink

buttons b e

erased for security purposes.

1) HomeLink

button 1

2) HomeLink

button 2

3) HomeLink

button 3

1. Press and hold the two outer buttons

(button 1 and button 3) until the indicator

light begins to flash (after approximately

20 seconds).

2. Release both buttons.

! In case a problem occurs

If you cannot activate a device using the

corresponding HomeLink

button af ter

programming, contact HomeLink

ink.co m or call 1-800-355-

3515 for assistance.

& Auto-dimming mirror (if

equipped)

1) LED

2) Switch

3) Sensor

The auto-dimming mirror has an anti-glare

feature which automatically reduces glare

coming from headlights of vehicles behind

you.

By pressing and holding the switch for

less than 3 seconds, the automatic dim-

ming function is toggled on or off. When

the automatic dimming function is on, the

LED indicator will illuminate.

Even with the mirror in anti-glare mode,

the mirror surface turns bright if the shift

lever/select lever is shifted into the “R”

(reverse) position. This is to ensure good

reward visibility during reversing.

When cleaning the mirror, use a paper

towel or similar material dampened with

glass cleaner. Do not spray glass cleaner

directly on the mirror as that may cause

the liquid cleaner to enter the mirror

housing and damage the mirror.

! Photosensors

The mirror has a photosensor attached on

the front and back sides. During nighttime

driving, these sensors detect distracting

glare from vehicle headlights behind you

and automatically dim the mirror to elim-

inate glare and preserve your vision. For

this reason, use care not to cover the

sensors with stickers, or other similar

items. Periodically wipe the sensors clean

using a piece of dry soft cotton cloth or an

Instruments and controls 3-57

– CONTINUED –

3-58 Instruments and controls

applicator.

& Auto-dimming mirror with

HomeLink

(if equipped)

1) HomeLink

button 1

2) HomeLink

button 2

3) LED

4) HomeLink

button 3

5) Sensor

6) Automatic dimming on button

7) Automatic dimming off button

The auto-dimming mirror has an anti-glare

feature which automatically reduces glare

coming from headlights of vehicles behind

you. It also contains a HomeLink

wireless

control system.

By pressing the automatic dimming on/off

button, the automatic dimming function is

turned on or off. When the automatic

dimming function is on, the LED indicator

will illuminate.

Even with the mirror in the automatic

dimming mode, the mirror surface turns

bright if the shift lever/select lever is

shifted into the “R” (reverse) position. This

is to ensure good rearward visibility during

reversing.

When cleaning the mirror, use a paper

towel or similar material dampened with

glass cleaner. Do not spray glass cleaner

directly on the mirror as that may cause

the liquid cleaner to enter the mirror

housing and damage the mirror.

! Photosensors

The mirror has a photosensor attached on

both the front and back sides. During

nighttime driving, these sensors detect

distracting glare from vehicle headlights

behind you and automatically dim the

mirror to eliminate glare and preserve

your vision. For this reason, use care not

to cover the sensors with stickers, or other

similar items. Periodically wipe the sen-

sors clean using a piece of dry soft cotton

cloth or an applicator.

! HomeLink

Wireless Control Sys-

tem

The HomeLink

Wireless Control System

can be used to activate remote control

devices such as gate operators, garage

door openers, door locks, home lighting

and security systems.

There are three HomeLink

buttons on the

mirror, each of which can be programmed

for operation of one desired device. For

details on the device types which can be

operated by this sys tem, consult the

HomeLink

website at:

wwmelink.com or call 1-800-355-

3515.

Note the following information about this

system.

If you r vehicle is equipped w ith the

HomeLink

Wireless Control System, it

complies with Part 15 of the Federal

Communications Commission Rules in

the U.S. and the RSS-210 of Industry

Canada in Canada. Its operation is subject

to the following two conditions:

(1) this device may not cause harmful

interferen ce, and (2) this device must

accept any interference received, includ-

ing interference that may cause undesired

operation.

Changes and modifications to this system

by an yone other than an authorized

service facility could void authorization to

use this equipment.

HomeLink

and the HomeLink

house are

registered trademarks of Johnson Con-

trols, Inc.

WARNING

. W h e n p r o g r a m m i n g t h e

HomeLink

Wireless Control Sys-

tem, you may be oper ating a

garage do or opener or other

device. Make sure that people

and objects are out of the way

of the garage door or other

device to prevent potential harm

or damage.

. Do not use the HomeLink

Wire-

less Control System with a gar-

age door opener that lacks the

safety stop and reverse feature

as required by applicable safety

standards. A garage door opener

which cannot detect an object,

signaling the door to stop and

reverse, do es not meet these

safety standards. Using a garage

door opener without these fea-

tures increases risk of serious

injury or death. For more infor-

mation, consult the HomeLink

website at or

call 1-800-355-3515.

CAUTION

When programming the HomeLink

Wireless Control System to operate

a garage door opener or an entrance

gate, unplug the dev ice’s motor

from the outlet during programming

to prevent motor burnout.

NOTE

. After programming your HomeLink

Wireless Control System for the de-

sired devices, retain the hand-held

transmitters for further programming

or device testing in the event of a

problem.

. It is recommended that you insert a

new battery in the hand-held transmit-

ter of a device to ensure correct

programming.

! Garage door opener programming in

the U.S.A.

NOTE

When programming th e HomeLink

Wireless Control System for a garage

door opener, it is suggested that you

park the vehicle outside the garage.

1. Unplug the motor of the garage door

opener from the outlet.

NOTE

If any of the HomeLink

buttons are

already programmed for other devices,

skip step 2 because it clea rs the

memory of all three buttons.

Instruments and controls 3-59

– CONTINUED –

3-60 Instruments and controls

1) HomeLink

button 1

2) HomeLink

button 2

3) HomeLink

button 3

2. Press and hold the two outer

HomeLink

buttons (button 1 and button

3) until the indicator light begins to flash

(after approximately 20 seconds). Then

release both buttons.

3. Hold the end of the garage door

opener’s hand-held transmitter between

1 and 3 inches (25 and 76 mm) away from

the HomeLink

button you wish to pro-

gram.

4. Simultaneously press and hold both

the hand-held transmitter button and the

desired HomeLink

button. DO NOT re-

lease the buttons until step 5 has been

completed.

NOTE

Some gate operators and garage door

openers may require you to replace

this programming step 4 with proce-

dures in “Programming for entrance

gates and garage door openers in

Canada” F3-61.

5. Hold down both but tons until the

HomeLink

indicator light flashes, first

slowly then rapidly. When the indicator

light flashes rapidly, both buttons may be

released. (The rapidly flashing light indi-

cates successful programming of the new

frequency signal.)

6. Press and hold the programmed but-

ton and check the HomeLink

indicator

light. If the indicator light stays on con-

tinuously, your garage door should acti-

vate and the programming is completed.

If the indicator light flashes rapidly for 2

seconds and then stays on continuously,

your garage door opener may be pro-

tected by a rolling code feature. In this

case you need to perform the additional

steps that are described in “Programming

rolling-code-protected garage door open-

ers in the U.S.A.” F3-60.

! Programming rolling-code-protected

garage door openers in the U.S.A.

If your garage door opener has a rolling

code feature, program the HomeLink

Wireless Control System for it by following

steps 1 through 5 in “Garage door opener

programming in the U.S.A.” F3-59. Then

continue with the following steps.

NOTE

The assistance of a second person

may make the programming quicker

and easier.

1. Locate t he tr aining button on the

garage door opener motor head unit.

The exact location and color of the button

may vary by brand of garage door opener.

If it is difficult to locate the training button,

refer to your garage door opener’s instruc-

tion manual.

1) Training button

2. Press the training button on the

garage door opener motor head unit

(which activates the “training light” on the

unit). Proceed to step 3 within 30 seconds.

3. Inside the vehicle, firmly press, hold for

2 seconds and release the HomeLink

button that was programmed in the pre-

vious section. Press and release the

button a second time to complete the

programming procedure.

NOTE

Some garage door openers may re-

quire you to do the above press-hold-

release sequence a third time to com-

plete the programming.

4. The garage door opener should now

recognize the HomeLink

Wireless Control

System and your garage door opener

should activate when the HomeLin k

button is pressed.

! Programming for entrance gates and

garage door openers in Canada

1. Unplug the motor of the entrance gate

or garage door opener from the outlet.

NOTE

If any of the HomeLink

buttons are

already programmed for other devices,

skip step 2 because it clears the

memory of all three buttons.

1) HomeLink

button 1

2) HomeLink

button 2

3) HomeLink

button 3

2. Press and hold the two outer

HomeLink

buttons (button 1 and button

3) until the HomeLink

indicator light

begins to flash (after approximately 20

seconds). Then release both buttons.

3. Hold the end of the entrance gate’s/

garage door opener’s hand-held transmit-

ter between 1 and 3 inches (25 and 76

mm) away from the HomeLink

button you

wish to program.

4. Press and hold the desired HomeLink

button.

5. Press and release (“cycle”) the hand-

held transmitter button every 2 seconds

until step 6 is complete.

Instruments and controls 3-61

– CONTINUED –

3-62 Instruments and controls

6. When the indicator light flashes slowly

and then rapidly after several seconds,

release both buttons.

7. Plug the motor of the entrance gate/

garage door opener to the outlet.

8. Test your entrance gate/garage door

opener by pr essing the pr ogrammed

HomeLink

button.

! Operating the HomeLink

Wireless

Control System

Once programmed, the HomeLink

Wire-

less Control System can be used to

remote-control the devices to which its

buttons are programmed. To activate a

device, simply press the appropriate but-

ton. The indicator light illuminates, indicat-

ing that the signal is being transmitted.

! Programming other devices

To program other devices such as door

locks, home lighting and security systems,

contact HomeLink

at www.

or call 1-800-355-3515.

! Reprogramming a single HomeLink

button

1. Press and hold the HomeLink

button

you wish to reprogram. DO NOT release

the button until step 4 has been com-

pleted.

2. When the HomeLink

indicator light

begins to flash slowly (after approximately

20 seconds), position the hand-held trans-

mitter of the device between 1 to 3 inches

(25 to 76 mm) away from the HomeLink

button you wish to program.

3. Press and hold the hand-held trans-

mitter button. The HomeLink

indicator

light will flash, first slowly and then rapidly.

4. When the indicator light begins to flash

rapidly, release both buttons.

The programming for the previous device

is now erased and the new device can be

operated by press ing the HomeLink

button.

! Erasing HomeLink

button memory

NOTE

. Performi ng this procedure erases

the memory of all the preprogrammed

buttons simultaneously. The memory

of individual buttons cannot be erased.

. It is recommended that upon the

sale of the vehicle, the memory of all

programmed HomeLink

button s be

erased for security purposes.

1) HomeLink

button 1

2) HomeLink

button 2

3) HomeLink

button 3

1. Press and hold the two outer buttons

(button 1 and button 3) until the indicator

light begins to flash (after approximately

20 seconds).

2. Release both buttons.

! In case a problem occurs

If you cannot activate a device using the

correspondi ng HomeLink

button after

programming, contact HomeLink

ink.com or call 1-800-355-

3515 for assistance.

& Outside mirrors

! Convex mirror (passenger side)

WARNING

Objects look smaller in a convex

mirror and farther away than when

viewed in a flat mirror. Do not use

the convex mirror to judge the

distance of vehicles behind you

when changing lanes. Use the inside

mirror (o r glance backwa rds) to

determine the actual size and dis-

tance of objects that you view in

convex mirror.

! Remote control mirror switch

The remote control mirrors operate only

when the ignition switch is in the “ON” or

“Acc” position.

1. Turn the knob to the “L” side to adjust

the left-hand mirror or to the “R” side to

adjust the right-hand mirror.

2. Move the knob in the direction you

want to move the mirror.

3. Return the knob to the neutral position

to prevent unintentional operation.

The mirrors can also be adjusted manu-

ally.

! Power folding mirror switch (if

equipped)

The power folding mirror switch operates

only when the ignition switch is in the “ON”

or “Acc” position.

To fold the outside mirrors, push the power

folding mirror switch. To unfold the mirrors,

push the switch again.

NOTE

. When the temperature is low, the

outside mirrors may stop during opera-

tion. Push the switch again. When the

outside mirrors do not work by operat-

ing the switch, move the outside mir-

rors several times manually. This

makes it possible to operate them by

switch operation.

. When you operate the power folding

Instruments and controls 3-63

– CONTINUED –

Instruments and controls -> Mirrors for Your Subaru Outback SUV Fourth Generation (2010-2014)

Related Topics

Popular Owner Manuals

Latest Owner Manuals