Get Instruments and controls -> Multi information display (type A combination meter) Guide for Subaru Outback SUV Fourth Generation (2010-2014)

3-36 Instruments and controls

1) U.S. spec. models

2) Except U.S. spec. models

If the driving range is shown as “

”,

there is only a tiny amount of fuel left in the

tank. You must refuel the vehicle immedi-

ately.

NOTE

The driving range on remaining fuel is

only a guide. The indicated value may

differ from the actual driving range on

remaining fuel, so you must immedi-

ately fill the tank when the low fuel

warning light illuminates.

Multi information display

(models with type A combi-

nation meter)

WARNING

Always pay adequate attention to

safe driving when operating the

multi information display while the

vehicle is in motion. When operation

of the multi information display

interferes with your ability to con-

centrate on driving, stop the vehicle

before performing operations on the

screen. Also, do not concentrate on

the display while driving. Doing so

may cause you to look away from

the road and could resul t in an

accident.

Various information will be shown on the

multi information display. Also, a warning

message will appear on the display if a

malfunction, etc. is detected. In addition,

several settings for the displayed content

can be performed.

Multi information display

1) ECO gauge (refer to “ECO gauge” F3-

11.)

2) Warning screen (refer to “Warning

screen” F3-38.)/Basic screen (refer to

“Basic screens” F3-38.)

3) Select lever/gear position indicator (refer

to “Select lever/gear position indicator”

F3-30.)

4) Cruise control information display

5) Odometer (refer to “Odometer” F3-8.)/

double trip meter (refer to “Double trip

meter” F3-9.)

Control switch

1) Up (select)

2) Set (enter)

3) Down (select)

& Basic operation

By operating “

” or “ ” of the control

switch, the screens and selection items

can be switched. When the “

/SET”

switch is pulled toward you, the item can

be selected and set.

If there are some useful messages, such

as vehicle information, warning informa-

tion, etc., they will interrupt the current

screen, and appear on the display accom-

panied by a beep. If such a screen is

displayed, take proper action according to

the message shown on the screen.

The warning screen will return to the

original screen after a few seconds. While

the “

” information reminder is shown on

the display, it may be possible to display

the warning screen again. To recall the

message marked with “

” on the display,

pull the “

/SET” switch on the steering

wheel toward you.

& Welcome screen

When the door is unlocked and the

driver’s door is opened, the welcome

screen will appear for approximately 20

seconds.

NOTE

. The welcome screen will disappear

when the ignition switch is turned to

the “ON” position while the welcome

screen is displayed.

. If any of the doors (including the

rear gate) is opened while the welcome

screen is displayed, the door ajar

warning will appear.

. The welcome screen can be set to

on or off. For details, refer to “Welcome

Good-bye Screen” F3-40.

& Starting screen

When the ignition switch is turned to the

“ON” posit ion, the starting screen will

appear for approximately 2 seconds.

Instruments and controls 3-37

– CONTINUED –

3-38 Instruments and controls

& Good-bye screen

When the ignition switch is turned to the

“LOCK”/ “OFF” position, the “Good-bye”

screen will appear for approximately 3

seconds.

& Warning screen

Example of warning

If there is a w arning message or a

maintenance notification, it will appear for

approximately 3 seconds. Take the appro-

priate actions based on the messages

indicated.

& Basic screens

By operating the “

” or “ ” switch on the

s teering wheel, you can c hange the

screen that is always displayed.

Default screen:

Journey time screen:

This screen displays the journey time (the

time that has elapsed since the ignition switch

was turned to the “ON” position).

Menu screen entering screen:

While this screen is selected, pull the “ /

SET” switch to enter the menu screen.

& Menu screens

Pull the “

/SET” switch to enter the menu

screens when all of the following condi-

tions are satisfied.

. The vehicle has been completely

stopped.

. The select lever is in the “P” position.

. The menu screen entering screen is

selected.

. The “

” information reminder is off.

The menu list is as follows.

First menu

Second menu

Screen Settings Welcome Good-bye Screen

Gauge Initial Movement

Languages

Return

EyeSight (models with EyeSight system) Warning Volume

Lead Vehicle Acquisition Sound

Lead Vehicle Moving Monitor Function

Return

Auto Light Sensor

―

Default Settings

―

Instruments and controls

3-39

– CONTINUED –

3-40 Instruments and controls

By operating the “

” or “ ” switch on the

steering wheel, you can select the menu.

Pull the “

/SET” switch to enter the

selected menu.

NOTE

If you enter the “Return” menu, the

system will return to the previous

screen.

! Screen Settings

After entering the “Screen Settings” menu,

select one of the following menus.

! Welcome Good-bye Screen

The welcome screen/good-bye screens

can be activated or deactivated. Select

“On” to activate the screens. Select “Off”

to deactivate the screens.

! Gauge Initial Movement

The movement of the meter needles and

gauge needles that occurs when the

ignition switch is turned to t he “ON”

position can be activated or deactivated.

Select “On” to activate. Select “Off” to

deactivate.

! Languages

Operate the “

” or “ ” switch on the

steering wheel to display the preferred

language. Then pull the “

/SET” switch to

select the displayed language.

! EyeSight (models with EyeSight

system)

NOTE

For models with the EyeSight system,

refer to the Owner’s Manual supple-

ment for the EyeSight system.

After entering the “EyeSight” menu, select

one of the following menus.

! Warning Volume

The volume of the warning buzzer that

sounds when the EyeSight system is in

use can be set in 3 stages (“Max”, “Mid”

and “Min”).

! Lead Vehicle Acquisition Sound

When adaptive cruise control is used, the

buzzer that sounds if a vehicle is detected

in front or if detection is not possible can

be activated or deactivated. Select “On” to

activate the buzzer. Select “Off” to deac-

tivate the buzzer.

! Lead Vehicle Moving Monitor Func-

tion

When adaptive cruise control is used, the

buzzer that sounds if a vehicle in front has

started can be activated or deactivated.

Select “On” to activate the buzzer. Select

“Off” to deactivate the buzzer.

! Auto Light Sensor

The operational sensitivity of the auto on/

off headlights can be set. You can select

“Min”, “Low”, “Mid” or “Max”.

! Default Settings

Select “Yes” to use the menu screen to

restore customized settings to the factory

default settings. Select “No” to return to

the previous screen without restoring to

the factory default settings.

Instruments and controls -> Multi information display (type A combination meter) for Your Subaru Outback SUV Fourth Generation (2010-2014)

Related Topics

Popular Owner Manuals

Latest Owner Manuals