Get Seat, Seatbelt and SRS Airbags -> Head Restraint Adjustment (Front Seats) Guide for Subaru Outback SUV Sixth Generation (2020-2025)

(39,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

driver’s door is opened, the registered

memory position can be retrieved even

if the ignition switch is in the “LOCK” or

“OFF” position.

. If buttons “1” and “2” are pressed at

the same time, execution of seat posi-

tion retrieval may not be possible.

. When the retrieved position is the

same as the current seat position, a

chirp will sound twice.

! Utilizing of the seat position

registered with access key fob

s01aa020704

1. Hold the registered access key fob.

2. Unlock the driver’s door by pressing

the “

” button or gripping the door handle.

3. Open the driver’s door.

A chirp sounds and the seat moves to the

registered position.

When the select lever is moved to the “R”

position, the outside mirror will move to the

registered reverse tilt-down position.

NOTE

. If the registered seat position cannot

be retrieved after performing the pre-

vious procedures, try the following

procedures.

(1) Press the “SET” button on the

driver’s door.

(2) Press the “

” button on the

access key fob or touch the door

lock sensor to lock the doors.

(3) Perform the prior procedures

again.

. If the keyless access function is

disabled, the seat position cannot be

retrieved by gripping the driver’s door

handle. However, the seat position can

still be retrieved by pressing the “

”

button on the access key fob. For

information about how to enable/dis-

able the keyless access function, refer

to “Disabling Keyless Access Func-

tion” �P129.

. If a new position is registered for the

same access key fob, the previously

registered seat position is deleted.

. If you are carrying 2 or more access

keys, seat position retrieval may not be

possible.

! Clearing the registered seat posi-

tion with access key fob

s01aa020705

1. Close the driver’s door.

2. While holding the access key fob and

pressing the “SET” button, press the “

”

button on the access key fob.

A chirp will sound, and the registered seat

position will be cleared.

NOTE

After deleting the seat position, wait for

a few moments before registering a

new seat position.

& Head Restraint Adjustment

s01aa04

WARNING

. Never drive the vehicle with the

head restraints removed because

they are designed to reduce the

risk of serious neck injury in the

event that the vehicle is struck

from the rear. Also, never install

the head restraints backwards.

Doing so will prevent the head

restraints from functioning as

intended. Therefore, when the

– CONTINUED –

Front Seats

Seat, Seatbelt and SRS Airbags

(40,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

head restraints are removed, all

head restraints must be rein-

stalled properly to protect vehicle

occupants.

. The vehicle should not be oper-

ated until the head restraints are

installed in their proper posi-

tions.

. The front seat head restraints are

designed to be installed into the

front seats only. The rear seat

head restraints are designed to

be installed into the rear seats

only. Do not attempt to install the

front seat head restraints into the

rear seats, or the rear seat head

restraints into the front seats.

Both the driver’s seat and front passen-

ger’s seat are equipped with head re-

straints. Both head restraints are adjusta-

ble in the following ways.

! Head restraint height adjustment

s01aa0401

1) Head restraint

2) Release button

To raise:

Pull the head restraint up.

To lower:

Push the head restraint down while press-

ing the release button on the top of the

seatback.

To remove:

While pressing the release button, pull out

the head restraint.

To install:

Install the head restraint into the holes that

are located on the top of the seatback until

the head restraint locks. Press and hold

the release button to lower the head

restraint.

Each head restraint should be adjusted so

that the center of the head restraint is

closest to the top of the occupant’s ears.

NOTE

It is not possible to remove or install the

head restraint without reclining the

front seatback. Reclining the front seat-

back and then remove or install the

head restraint.

Front Seats

(41,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

! Head restraint angle adjustment

s01aa0402

The angle of the head restraint can be

adjusted in several steps. While maintain-

ing a suitable driving posture, adjust the

head restraint to a position where the back

of your head is as close to the head

restraint as possible.

To tilt:

Tilt the head restraint by hand to the

preferred position. A click will be audible

when the head restraint is locked.

To return:

Tilt the head restraint once as far forward

as it can go. The head restraint will

automatically return to the fully upright

position. Then, adjust the head restraint

again to the preferred angle.

1-2. Seat Heater (If Equipped)

s01ab

The seat heater operates when the ignition

switch is in the “ON” position.

CAUTION

. Do not put hard or heavy objects

or ones with protrusions on the

seat, and do not stab the seat

with sharp objects, such as pins

or needles.

. People with delicate skin may

suffer slight burns even at low

temperatures if they use the seat

heater for a long period of time.

When using the heater, always be

sure to warn the persons con-

cerned.

. Do not put anything on the seat

which insulates against heat,

such as a blanket, cushion, or

Seat, Seatbelt and SRS Airbags -> Head Restraint Adjustment (Front Seats) for Your Subaru Outback SUV Sixth Generation (2020-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals