Get Seat, Seatbelt and SRS Airbags -> Power Seat (If Equipped) Guide for Subaru Outback SUV Sixth Generation (2020-2025)

(34,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

& Power Seat (If Equipped)

s01aa02

! Driver’s seat (2-way lumbar support

models)

s01aa0208

1) Seat position forward/backward con-

trol switch

To adjust the seat forward or backward,

move the control switch forward or

backward. During forward/backward ad-

justment of the seat, you cannot adjust

the seat cushion angle or seat cushion

height.

2) Seat cushion angle control switch

To adjust the seat cushion angle, pull up

or push down the front end of the control

switch.

3) Seat height control switch

To adjust the seat height, pull up or push

down the rear end of the control switch.

4) Seatback angle (reclining) control

switch

To adjust the angle of the seatback, move

the control switch.

5) Lumbar support control switch

To increase lower back support, push the

front side of the switch. To decrease

lower back support, push the rear side of

the switch.

! Driver’s seat (4-way lumbar support

models)

s01aa0211

1) Seat position forward/backward con-

trol switch

To adjust the seat forward or backward,

move the control switch forward or

backward. During forward/backward ad-

Front Seats

(35,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

justment of the seat, you cannot adjust

the seat cushion angle or seat cushion

height.

2) Seat cushion angle control switch

To adjust the seat cushion angle, pull up

or push down the front end of the control

switch.

3) Seat height control switch

To adjust the seat height, pull up or push

down the rear end of the control switch.

4) Seatback angle (reclining) control

switch

To adjust the angle of the seatback, move

the control switch.

5) Lumbar support control switch

To increase lower back support, push the

front side of the switch. To decrease

lower back support, push the rear side of

the switch.

To adjust the lumbar support height, push

the upper or lower side of the switch.

! Front passenger’s seat (if equipped)

s01aa0209

1) Seat position forward/backward con-

trol switch

To adjust the seat forward or backward,

move the control switch forward or

backward.

2) Seat cushion angle control switch

To adjust the seat cushion angle, pull up

or push down the front end of the control

switch.

3) Seat height control switch

To adjust the seat height, pull up or push

down the rear end of the control switch.

4) Seatback angle (reclining) control

switch

To adjust the angle of the seatback, move

the control switch.

! Thigh extension (driver’s seat – if

equipped)

s01aa0210

CAUTION

When the thigh extension is pulled

out to its fullest, do not put weight on

the top of it. Doing so could break

the part.

The seat front length can be adjusted.

Pull up the lever “1” to adjust the length

and release the lever to lock it.

– CONTINUED –

Front Seats

Seat, Seatbelt and SRS Airbags

(36,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

! Power driver’s seat with synchro-

nized outside mirrors memory

function (if equipped)

s01aa0207

WARNING

. To avoid loss of vehicle control or

personal injury, never perform

the following operations while

driving.

– Adjusting the seat

– Selecting a registered seat

position

. Before adjusting the seat or se-

lecting a registered seat position,

make sure that cargo or the

hands and feet of rear seat pas-

sengers are clear of the adjusting

mechanism.

. The memory adjustment of the

seat position is finished. Be sure

to confirm that the select lever is

in the “P” position, and the park-

ing brake is applied, when adjust-

ing the seat position. Do not drive

until the utilizing of the seat

position is complete.

. When any unusual conditions or

malfunctions occur during the

memory adjustment of the seat

position, stop the memory ad-

justment of the seat position by

performing any of the following

procedures.

– Operate any of the power seat

switches.

– Press the “SET” button.

– Press button “1” or “2”.

– Operate the outside mirror

control switch.

“2” or each of the key fobs.

The following memory positions can be

registered.

. Forward/backward position of the seat

. Angle of the seatback

. Angle of the seat cushion

. Height of the seat

. Angle of the outside mirrors

. Angle of the outside mirror angle on the

passenger’s side when the reverse tilt-

down operates.

NOTE

The seat position can also be retrieved

with the Driver Monitoring System user

information. To do so, perform user

registration in the Driver Monitoring

System settings. Refer to “Driver Mon-

itoring System” �P233.

! Registration of memory position

with button “1” or “2”

s01aa020701

1. Adjust the seat and outside mirror

positions under the following conditions.

. The parking brake is applied.

. The ignition switch is in the “ON”

position.

. The select lever is in the “P” position.

2. Register the adjusted positions by

either of the following procedures.

. Press the “SET” button, then press

either “1” or “2” until a chirp sounds

within 5 seconds.

. While pressing and holding the

“SET” button, press either “1” or “2”

until a chirp sounds within 5 seconds.

Front Seats

(37,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

A chirp will sound once, and the seat

position and outside mirror angle on the

passenger’s side will be registered.

NOTE

If a new position is registered for the

same button, the previously registered

memory position is deleted.

! Registration of the reverse tilt-

down mirror angle with button

“1” or “2”

s01aa020706

CAUTION

Depress the brake pedal when re-

gistering the reverse tilt-down mir-

ror angle.

1. Move the select lever to the “R”

position, then the outside mirror angle on

the passenger’s side will move to the

reverse tilt-down position.

2. Adjust the outside mirror angle on the

passenger’s side. For details about the

settings, refer to “Remote control mirror

switch” �P295.

3. Move the select lever to the “P”

position, then the outside mirror angle will

return to its original position.

4. Register the adjusted positions by

either of the following procedures.

. Press the “SET” button, then press

either “1” or “2” until a chirp sounds

within 5 seconds.

. While pressing and holding the

“SET” button, press either “1” or “2”

until a chirp sounds within 5 seconds.

A chirp will sound once, and the seat

position and outside mirror angle on the

passenger’s side will be registered.

NOTE

. The outside mirror angle will return

to its original position approximately 9

seconds after the select lever is moved

to any position other than “R” position.

. The factory setting (default setting)

for this function is set as the front

passenger’s side mirror. The setting of

the driver’s side mirror operation can

be changed by a SUBARU dealer.

Contact your SUBARU dealer for de-

tails.

! Registration of memory position

with an access key fob (if

equipped)

s01aa020703

1. Adjust the memory position under the

following conditions.

. The parking brake is applied.

. The ignition switch is in the “LOCK”/

“OFF” position.

. The select lever is in the “P” position.

2. Hold the access key fob and press and

hold the “SET” button. Then press the “

”

button of the access key fob.

A chirp will sound once, and the memory

position is registered.

NOTE

When registering the seat position,

carry the access key that you want to

or more access keys, registration may

not be possible.

– CONTINUED –

Front Seats

Seat, Seatbelt and SRS Airbags

(38,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

! Registration of the reverse tilt-

down mirror angle with the key

fob

s01aa020707

CAUTION

Depress the brake pedal when re-

gistering the reverse tilt-down mir-

ror angle.

1. Move the select lever to the “R”

position, then the outside mirror angle will

move to the reverse tilt-down position.

2. Adjust the outside mirror angle. For

details about the settings, refer to “Remote

control mirror switch” �P295.

3. Move the select lever to the “P”

position, then the outside mirror angle will

return to its original position.

4. Turn the ignition switch to the “OFF”/

“LOCK” position.

5. Hold the access key fob and press and

hold the “SET” button, then press the “

”

button of the access key fob.

A chirp will sound once, and the reverse

tilt-down mirror angle will be registered.

NOTE

. The outside mirror angle will return

to its original position approximately 9

seconds after the select lever is moved

to any position other than “R” position.

. The factory setting (default setting)

for this function is set as the front

passenger’s side mirror. The setting of

the driver’s side mirror operation can

be changed by a SUBARU dealer.

Contact your SUBARU dealer for de-

tails.

. The system stores the adjusted

mirror angle for approximately 45 sec-

onds after the ignition switch is turned

to the “OFF” position. Register the

mirror angle while the memory function

is available.

! Utilizing of memory position

registered with button “1” or “2”

s01aa020702

WARNING

Be sure to press the correct button

to retrieve your registered memory

position. If the seat position is not

optimum for you, it may adversely

affect your driving and may reduce

the effectiveness of the seatbelt.

That could result in an accident

involving serious injury or death.

1. Turn the ignition switch to the “ON”

position.

2. Put the select lever is in the “P” position

and apply the parking brake. Then press

button “1” or “2”.

A chirp will sound and the seat and angle

of the outside mirrors moves to the

registered position.

When the select lever is moved to the “R”

position, the outside mirror will move to the

registered reverse tilt-down position.

NOTE

. If the vehicle battery is removed, the

registered memory position data will

not be deleted.

. When the button “1” or “2” is

pressed within 45 seconds after the

Front Seats

(39,1)

北米Model "A2620BE-A" EDITED: 2022/ 4/ 25

driver’s door is opened, the registered

memory position can be retrieved even

if the ignition switch is in the “LOCK” or

“OFF” position.

. If buttons “1” and “2” are pressed at

the same time, execution of seat posi-

tion retrieval may not be possible.

. When the retrieved position is the

same as the current seat position, a

chirp will sound twice.

! Utilizing of the seat position

registered with access key fob

s01aa020704

1. Hold the registered access key fob.

2. Unlock the driver’s door by pressing

the “

” button or gripping the door handle.

3. Open the driver’s door.

A chirp sounds and the seat moves to the

registered position.

When the select lever is moved to the “R”

position, the outside mirror will move to the

registered reverse tilt-down position.

NOTE

. If the registered seat position cannot

be retrieved after performing the pre-

vious procedures, try the following

procedures.

(1) Press the “SET” button on the

driver’s door.

(2) Press the “

” button on the

access key fob or touch the door

lock sensor to lock the doors.

(3) Perform the prior procedures

again.

. If the keyless access function is

disabled, the seat position cannot be

retrieved by gripping the driver’s door

handle. However, the seat position can

still be retrieved by pressing the “

”

button on the access key fob. For

information about how to enable/dis-

able the keyless access function, refer

to “Disabling Keyless Access Func-

tion” �P129.

. If a new position is registered for the

same access key fob, the previously

registered seat position is deleted.

. If you are carrying 2 or more access

keys, seat position retrieval may not be

possible.

! Clearing the registered seat posi-

tion with access key fob

s01aa020705

1. Close the driver’s door.

2. While holding the access key fob and

pressing the “SET” button, press the “

”

button on the access key fob.

A chirp will sound, and the registered seat

position will be cleared.

NOTE

After deleting the seat position, wait for

a few moments before registering a

new seat position.

& Head Restraint Adjustment

s01aa04

WARNING

. Never drive the vehicle with the

head restraints removed because

they are designed to reduce the

risk of serious neck injury in the

event that the vehicle is struck

from the rear. Also, never install

the head restraints backwards.

Doing so will prevent the head

restraints from functioning as

intended. Therefore, when the

– CONTINUED –

Front Seats

Seat, Seatbelt and SRS Airbags

Seat, Seatbelt and SRS Airbags -> Power Seat (If Equipped) for Your Subaru Outback SUV Sixth Generation (2020-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals