2004-2008 Suzuki Alto 4 Door Inspection and Maintenance -> Bulb Replacement User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Inspection and Maintenance -> Bulb Replacement for Your Suzuki Alto 4 Door Sixth Generation (2004-2008)

115
76G-74E
INSPECTION AND MAINTENANCE
9-32
Always be sure to replace a blown
fuse with a fuse of the correct
amperage. Never use a substitute
such as aluminium foil or wire to
replace a blown fuse. If you replace
a fuse and the new one blows in a
short period of time, you may have a
major electrical problem. Have your
vehicle inspected immediately by your
MARUTI SUZUKI dealer.
NOTE:
Make sure that the fuse box always carries
spare fuses.
ww
ww
w WARNING
76G-09-043
BULB REPLACEMENT
• Light bulbs can be hot enough to
burn your finger right after being
turned off. This is true especially for
halogen headlight bulbs. Replace the
bulbs after they become cool
enough.
• The headlight bulbs are filled with
pressurized halogen gas. They can
burst and injure you if they are hit
or dropped. Handle them carefully.
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
Frequent replacement of a bulb
indicates the need for an inspection of
the electrical system. This should be
carried out by your MARUTI SUZUKI
dealer.
CAUTION
CAUTION
ww
ww
w WARNING
76G-09-044
76G-09-045
116
76G-74E
INSPECTION AND MAINTENANCE
9-33
Front Interior Light
Press the front part of the lens toward you
and pull down the lens. To install it, simply
push it back in.
The bulb can be removed by simply pulling
it out. When replacing the bulb, make sure
that the contact springs are holding the bulb
securely.
76G-09-046
Front Clearance/Turn Signal Light, Side
Turn Signal Light, rear Combination
Light, Registration Plate Light.
To remove a bulb holder from a light
housing, turn the holder counterclockwise
and pull it out. To install the holder, push
the holder in and turn it clockwise.
Two types (small oval and round) of bulb
are used for these lights. To remove and
install a small oval bulb, simply pull out or
push in the bulb.
76G-09-048
Headlights
Open the bonnet. Disconnect the coupler.
Remove the sealing rubber.
Push the retaining spring forward and
unhook it. Then remove the bulb. Install a
new bulb in the reverse order of removal.
Note:
Your vehicle is provided with two spare
he ad li gh t bu lb s fo r re pl ac em en t in
emegency.
76G-09-047
117
76G-74E
INSPECTION AND MAINTENANCE
9-34
To remove a round bulb from a bulb holder,
push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise. You can
access the individual bulb holders as
described below:
76G-09-049
Side turn signal light
Remove the lens by using a plain screw
driver covered with a soft cloth.
76G-09-051
Front clearance light / Turn Light
Trust this replacement job to your MARUTI
SUZUKI authorised workshop.
76G-09-050
118
76G-74E
INSPECTION AND MAINTENANCE
9-35
Rear combination light (tail, stop, turn
signal, etc.)
Undo the screws that secure the housing
and remove the housing by sliding in the
direction of the white arrow in the
illustration.
76G-09-052
WIPER BLADES
If the wiper blades become brittle or
damaged, or make streaks when wiping,
replace the wiper blades.
To install new wiper blades, follow the
procedure below.
To avoid scratching or breaking the
window, do not let the wiper arm
strike the windshield while replacing
the wiper blade.
CAUTION
76G-09-054
Registration plate light
Turn the lens counterclockwise and pull it
off
76G-09-053

Related Topics

Inspection and Maintenance
Periodic Maintenance Schedule Periodic Maintenance Schedule - Alto Periodic Maintenance Schedule - Alto K-10 Drive Belt Engine Oil and Filter Gear Oil Engine Coolant Windscreen Washer Fluid Air Cleaner Spark Plugs Fuel Filter Replacement Brakes Parking Brake Steering Clutch Pedal Tyres Tubeless Tyre (if equipped) Battery Fuses Wiper Blades

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot