Get Operating Your Vehicle -> Keyless Push Start System (if equipped) Guide for Suzuki Baleno 4 Door Second Generation (2015-2021)

3-6

OPERATING YOUR VEHICLE

Keyless Push Start System

(if equipped)

Provided the keyless push start system

remote controller is within the “interior

workable area” (refer to the related expla-

nation in this section), you can use the

engine switch for starting the engine and

selecting an ignition mode (“ACC” or

“ON”). In addition, the following functions

can be used:

• Keyless entry function. Refer to “Keyless

Push Start System Remote Controller” in

the “BEFORE DRIVING” section for

details.

• Locking and unlocking doors (including

the tailgate) using a request switch.

Refer to “Keyless Push Start System

Remote Controller” in the “BEFORE

DRIVING” section for details.

• Immobilizer (anti-theft) function. Refer to

“Immobilizer System” in the “BEFORE

DRIVING” section for details.

Engine Switch Illumination

The engine switch is illuminated (lit) in the

following situations:

• When the engine is off and the driver’s

door is open, or for 15 seconds after the

driver’s door is closed. The illumination

will fade out after 15 seconds pass.

• When the engine is off and the position

lights are on. The illumination will go out

when the position lights are turned off.

• When the engine is on and the position

lights and/or the headlights are on. The

illumination will go out when the position

lights and/or the headlights are turned

off.

82K253

NOTE:

To save the battery, the illumination will be

automatically turned off when both of the

following conditions are simultaneously

met:

• The headlights and position lights are

turned off.

• A period of 15 minutes has elapsed after

opening the driver’s door.

Selection of Ignition Modes

Press the engine switch to select the

“ACC” or “ON” mode as follows when you

use an electric accessory or check the

operation of instruments without running

the engine.

1) Bring the keyless push start system

remote controller with you and sit in the

driver’s seat.

2) Without depressing the clutch pedal,

press the engine switch (1).

68PH00303

Every time you press the engine switch,

the ignition mode changes as follows.

68PH00322

EXAMPLE

(1)

(

)

EXAMPLE

(OFF)

(Audio equipment)

)

(

Audio e

ment

)

EXAMPLE

3-7

OPERATING YOUR VEHICLE

NOTE:

When selecting the ignition modes, the

information display in the instrument clus-

tershows certain messages. Refer to

“Information Display” in the “BEFORE

DRIVING” section for details.

If the master warning indicator light

blinks and the ignition modes cannot

be selected

Your keyless push start system remote con-

troller may not be sensed as being within the

“interior workable area” (refer to the related

explanation in this section). Try again after

making sure you have the remote controller

with you. If the ignition modes still cannot be

selected, the battery of the remote controller

may be discharged. To be able to select an

ignition mode, you must then use the follow-

ing method:

68PH00304

1) Without depressing the brake pedal

and the clutch pedal, push the engine

switch (1).

2) Within about 10 seconds during which

the master warning indicator light in the

instrument cluster is blinking and the

“PLACE KEY FOB ON START

SWITCH” message appears on the

information display, touch the engine

switch with the “LOCK” button end of

the remote controller (2) for about 2

seconds. Then you should be able to

select ignition modes.

NOTE:

• If you still cannot select the ignition

modes, there may be some problem with

the keyless push start system. Contact

an authorised Maruti Suzuki workshop

for an inspection of the system.

• The immobilizer/keyless push start sys-

tem warning light will come on for about

5 seconds while the master warning indi-

cator light is blinking in addition, the

information display in the instrument

cluster will show a message during this

time. Refer to “Information Display” in

the “BEFORE DRIVING” section for

details.

• You may customize the system to cause

the interior buzzer to sound once for the

“remote controller out of sensing range”

warning. To incorporate this customiza-

tion, please contact an authorised Maruti

Suzuki workshop.

• If the battery of the remote controller is

about to become completely discharged,

the corresponding message will appear on

the information display when you press

the engine switch to change the ignition

mode to “ON”. Refer to “Information Dis-

play” in the “BEFORE DRIVING” section

for details. For details on replacing the bat-

tery, refer to the “Keyless Push Start Sys-

tem Remote Controller” in the “BEFORE

DRIVING” section.

“Remote Controller Outside” Warn-

ing

When either of the conditions described

below is met, the system issues a “remote

controller outside” warning by sounding the

interior and exterior buzzers.At the same

time the immobilizer/keyless push start

system warning light comes on and the

master warning indicator light blinks.

• Any door is opened and then closed

while the remote controller is not inside

the vehicle and the engine is running or

the ignition mode has been changed to

“ACC” or “ON” by pressing the engine

switch.

• The remote controller is not inside the

vehicle when you attempt to start the

engine after changing the ignition mode

to “ACC” or “ON” by pressing the engine

switch.

(1)

(2)

EXAMPLE

3-8

OPERATING YOUR VEHICLE

68PH02305

(1) Immobilizer/keyless push start sys-

tem warning light (blinks)

(2) Master warning indicator light (blinks)

NOTE:

• If the warning is given, locate the remote

controller as soon as possible.

• Any attempt to start the engine will fail

while the warning is active. The mes-

sage appearing on the information dis-

play in the instrument cluster will also

indicate this condition. Refer to “Informa-

tion Display” in the “BEFORE DRIVING”

section for details.

• Normally the immobilizer/keyless push

start system warning light should go out

and the master warning indicator light

should stop blinking shortly after the

remote controller is brought back inside

the vehicle. If they remain lit and blink-

ing, change the ignition mode to “LOCK”

(OFF) by pressing the engine switch and

then perform the engine starting opera-

tion Refer to “Starting the Engine” in this

section.

• Always keep the remote controller with

you as the driver.

Interior Workable Area for Engine

Starting, Ignition Mode Selection

and “Remote Controller Outside”

Warning

68PH00306

(1) Interior workable area

The “interior workable area” for these func-

tions is defined as all the interior spaces

except for the space above the instrument

panel.

NOTE:

• Even when the remote controller is in the

“interior workable area”, if it is in any of

the following conditions, you may not be

able to start the engine or select the igni-

tion modes, and the “remote controller

outside” warning may be given.

–The remote controller’s battery is low.

–The remote controller is affected by

strong radio signals or noise.

–The remote controller is in contact with

or covered by a metallic object.

(1)

(2)

(

)

(

)

EXAMPLE

(1)

EXAMPLE

3-9

OPERATING YOUR VEHICLE

–The remote controller is in stowage like

the glove box or a door pocket.

–The remote controller is in the sun visor

pocket or on the floor.

• Even when the remote controller is out-

side the “interior workable area”, if it is in

any of the following conditions, you may

be able to start the engine or select the

ignition mode. The “remote controller

outside” warning may not be given at

that time.

–The remote controller is outside the

vehicle but very close to a door.

–The remote controller is on the instru-

ment panel.

Parking Brake Lever

68PHM3001

(1) To set

(2) To release

(3) To release

The parking brake lever is located between

the seats. To set the parking brake, hold

the brake pedal down and pull the parking

brake lever all the way up. To release the

parking brake, hold the brake pedal down,

pull up slightly on the parking brake lever,

push the button on the end of the lever

with your thumb, and lower the lever to its

original position.

For CVT vehicles, always set the parking

brake before moving the gearshift lever to

the “P” (Park) position. If you park on an

incline and shift into “P” before setting the

parking brake, the weight of the vehicle

may make it difficult to shift out of “P” when

you are ready to drive the vehicle.

When preparing to drive the vehicle, move

the gearshift lever out of the “P” position

before releasing the parking brake.

(1)

(2)

(3)

EXAMPLE

WARNING

• Never drive your vehicle with the

parking brake on: rear brake effec-

tiveness can be reduced from over-

heating, brake life may be

shortened, or permanent brake

damage may result.

• If the parking brake does not hold

the vehicle securely or does not

fully release, have your vehicle

inspected immediately by autho-

rised Maruti Suzuki workshop.

WARNING

Always set the parking brake fully

before leaving your vehicle or it may

move, causing injury or damage.

When parking, make sure the gear-

shift lever for manual transaxle vehi-

cles is in reverse or first gear and the

gearshift lever for CVT vehicles is in

“P” (Park). Remember, even though

the transaxle is in gear or in Park,

you must set the parking brake fully.

Operating Your Vehicle -> Keyless Push Start System (if equipped) for Your Suzuki Baleno 4 Door Second Generation (2015-2021)

Related Topics

Popular Owner Manuals

Latest Owner Manuals