Get Other Controls and Equipment Guide for Suzuki Ignis SUV First Generation (2000-2008)

OTHER CONTROLS AND EQUIPMENT

60G407

OTHER CONTROLS AND EQUIPMENT

Fuel filler cap ....................................................................... 5-1

Engine hood ........................................................................ 5-2

Sun visor .............................................................................. 5-4

Interior light ......................................................................... 5-5

Accessory socket ................................................................ 5-6

AUX/USB socket (if equipped) ........................................... 5-7

Assist grips .......................................................................... 5-7

Glove box ............................................................................. 5-7

Cup holder and storage area ............................................. 5-8

Footrest ................................................................................ 5-10

Floor mats (if equipped) ..................................................... 5-10

Luggage compartment cover (if equipped) ...................... 5-11

Luggage compartment board ............................................. 5-11

Frame hooks ........................................................................ 5-12

Heating and air conditioning system ................................ 5-14

Manual heating and air conditioning system ................... 5-15

Automatic heating and air conditioning system

(climate control) (if equipped) ............................................ 5-19

Radio antenna ..................................................................... 5-24

Installation of radio frequency transmitters ..................... 5-25

Audio system (if equipped) ................................................ 5-25

5-1

OTHER CONTROLS AND EQUIPMENT

Fuel filler cap

66RH147

66RH050

A fuel filler cap is located on the left rear

side of the vehicle. The fuel filler door can

be unlocked by pulling up the opener lever

located on the outboard side of the driver’s

seat and locked by simply closing the door.

57L51093

To remove the fuel filler cap:

1) Open the fuel filler door.

2) Remove the cap by turning it counter-

clockwise.

75RM057

75RM058

NOTE:

The cap holder (1) holds the fuel filler cap

(2) by hooking the groove (3), or the hook

(4) also holds the fuel filler cap when refu-

eling.

EXAMPLE

CAUTION

Remove the fuel filler cap slowly. The

fuel may be under pressure and may

spray out, causing injury.

Open

EXAMPLE

(1)

(2)

(3)

(1)

EXAMPLE

(4)

(1)

EXAMPLE

5-2

OTHER CONTROLS AND EQUIPMENT

To reinstall the fuel filler cap:

1) Turn the cap clockwise until you hear

several clicks.

2) Close the fuel filler door.

Engine hood

66RH051

To open the engine hood:

1) Pull the hood release handle located on

the outboard side of the driver’s side.

This will disengage the engine hood

lock halfway.

66RH148

2) Push the under-hood release lever

sideways with your finger, as shown in

the illustration. While pushing the lever,

lift up the engine hood.

WARNING

Fuel is extremely flammable. Do not

smoke when refueling, and check

that there are no open flames or

sparks in the area.

WARNING

If you need to replace the fuel cap,

use a genuine MARUTI SUZUKI cap.

Use of an improper cap can result in

a malfunction of the fuel system or

emission control system. It may also

result in fuel leakage in the event of

an accident.

EXAMPLE

CAUTION

The release lever can be hot enough

to burn your finger right after driving.

Touch the lever after it becomes cool

enough.

NOTICE

Check that the wiper arms are not

raised before you lift up the engine

hood to avoid damaging the wiper

arms and the engine hood.

EXAMPLE

5-3

OTHER CONTROLS AND EQUIPMENT

66RH149

3) While holding the hood, pull the prop

rod out from the holding clip, and then

insert the end of the rod into the desig-

nated hole in the hood.

To close the engine hood:

1) Lift the hood up slightly and remove the

prop rod from the hole. Put the prop rod

back into the holding clip.

66RH150

2) Lower the hood to about 20 cm above

the hood latch, and then let it drop

down. Check that the hood is securely

latched after closing.

CAUTION

• The prop rod can be hot enough to

burn your finger right after driving.

Touch the rod after it becomes cool

enough.

• Insert the end of the rod into the

hole securely. If the rod slips out,

you may get caught in the closing

hood.

• The rod may slip out when the

hood is blown by wind. Be careful

on windy days.

EXAMPLE

WARNING

Check that the hood is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.

EXAMPLE

CAUTION

To avoid injury, check that no part of

the occupant’s body such as hands

or head is in the path of the hood

when closing it.

NOTICE

Pressing the hood from above may

damage the hood.

5-4

OTHER CONTROLS AND EQUIPMENT

Sun visor

79J161

The sun visors can be pulled down to block

glare coming through the windshield, or

they can be unhooked and turned to the

side to block glare coming through the side

window.

Card holder (if equipped)

74LHT0516

(1) Card holder

You can put a card in the card holder (1) on

the back of the sun visor.

Vanity mirror (if equipped)

74LHT0532

(2) Vanity mirror

NOTICE

When unhooking and hooking a sun

visor, be sure to handle it by the hard

plastic parts or the sun visor can be

damaged.

EXAMPLE

NOTICE

When you park your vehicle outdoors

in direct sunlight or in hot weather,

do not leave plastic cards in the

holder. The heat may distort them.

(1)

EXAMPLE

WARNING

When using the vanity mirror, do not

move too close to a front air bag

location or lean against it. If the front

air bag is accidentally inflated, it

could hit you hard.

(2)

EXAMPLE

5-5

OTHER CONTROLS AND EQUIPMENT

Interior light

Front

62R0294

These light switches have three or four

positions which function as described

below:

ON (1)

• The light comes on and stays on regard-

less of whether the door is open or

closed.

• To prevent battery from discharging, the

light will be automatically turned off

when a period of 15 minutes has

elapsed after the light comes on and

other operations are not done.

DOOR (2)

• The light comes on when any of the

doors (including the tailgate) is opened.

After closing all doors, the light will

remain on for about 15 seconds and

then fade out.

• If all doors are closed, the light comes on

for about 15 seconds when the ignition

key is pulled out from the ignition switch

or the engine switch is pressed to

change the ignition mode from ON to

LOCK (OFF). After 15 seconds, the light

will fade out.

• To prevent battery from discharging, the

light will be automatically turned off

when a period of 15 minutes has

elapsed after any of the doors (including

the tailgate) is opened and other opera-

tions are not done.

If you perform any of the following proce-

dures before the light fading out, the light

will start to fade out immediately.

• Inserting the ignition key into the ignition

switch or pressing the engine switch to

change the ignition mode to ACC or ON.

• Locking all doors by operating the key,

keyless entry transmitter, keyless push

start system remote controller, power

door locking switch or request switch.

OFF (3)

The light remains off even when the door is

opened.

Courtesy light (if equipped)

66RH128

Each front door has a courtesy light on its

inside bottom. It lights automatically when

the door is opened.

NOTE:

If you leave any door open, the light will

automatically be turned off after about 15

minutes to prevent the battery from dis-

charging.

(1)(2)(3)

EXAMPLE

5-6

OTHER CONTROLS AND EQUIPMENT

Luggage compartment (if equipped)

75RM009

When you open the tailgate with the lug-

gage compartment light switch in ON posi-

tion (1), the light comes on and remains on

as long as you keep the tailgate open.

• To save the battery, the light will be auto-

matically turned off when a period of 15

minutes has elapsed after the tailgate is

opened and other operations are not

done.

When the luggage compartment light

switch is in OFF position (2), the light

remains off regardless of whether the tail-

gate is open or close.

75RM193

NOTE:

The number of doors involved in the light-

ing operation of the interior light depends

on the vehicle specification. If there is a

switch (rubber protrusion) at the door

opening as shown, the door is involved in

the lighting operation. The tailgate is also

involved in this operation even without the

rubber protrusion.

Accessory socket

66RH129

The accessory socket will work when the

ignition switch is in “ACC” or “ON” position,

or the ignition mode is ACC or ON.

This can be used to provide 12 volt/120

watt/10 ampere power for electrical acces-

sories. Check that the cap is closed when

socket is not in use.

(2)(1)

EXAMPLE

NOTICE

Do not leave the tailgate open with

the luggage compartment light

switch in ON position for a long time,

or the battery will discharge.

EXAMPLE

NOTICE

Use of inappropriate electrical acces-

sories can cause damage to your

vehicle’s electrical system. Make

sure that any electrical accessories

you use are designed to plug into this

type of socket.

EXAMPLE

5-7

OTHER CONTROLS AND EQUIPMENT

AUX/USB socket (if equipped)

66RH130

Connect your portable digital music player,

etc. to this socket to enjoy music through

the vehicle’s audio system. Refer to “Audio

system” in this section.

Assist grips

54G249

Assist grips are provided for convenience.

Glove box

66RH055

To open the glove box, pull the latch lever.

To close it, push the lid until it latches

securely.

EXAMPLE

NOTICE

To avoid damaging the assist grip

and the molded headlining, do not

hang down the assist grip.

EXAMPLE

5-8

OTHER CONTROLS AND EQUIPMENT

66RH056

There is a recess in the glove box.

WARNING

Never drive with the glove box lid

open. It could cause injury if an acci-

dent occurs.

EXAMPLE

Cup holder and storage area

66RH057

(1) Center console tray (2) Front cup holders

(3) Front bottle holder (4) Rear cup holder

(5) Front seat back pocket (if equipped) (6) Rear bottle holder

(1)

(2)

(3) (6)(4)

(6)(5)(3)

(4)

EXAMPLE

5-9

OTHER CONTROLS AND EQUIPMENT

Center console tray (1) Front cup holders (2) /

Rear cup holder (4)

Use the rear cup holder to put a cup with a

lid or a bottle with a cap. Also, you can put

small articles in the rear cup holder.

Front bottle holder (3) /

Rear bottle holder (6)

You should only place a bottle with a cap in

the holder.

Front seat back pocket (5)

(if equipped)

66RH058

This pocket is provided for holding light

and soft things such as gloves, newspa-

pers or magazines.

WARNING

Do not place any objects which may

fall out from the pocket when the

vehicle is moving. Failure to take the

precaution may result in an object

interfering with the pedals and caus-

ing a loss of vehicle control or an

accident.

WARNING

Failure to take the precautions listed

below could cause personal injury or

vehicle damage.

• Be careful when you are using the

cup holders to hold a cup contain-

ing hot liquid. Spilling out hot liq-

uid can cause burn injury.

• Do not use the cup holders to hold

sharp-edged, hard or breakable

objects. Objects in the cup holders

may be thrown about during a sud-

den stop or impact, and could

cause personal injury.

• Be careful not to spill liquid or

insert any foreign materials into the

moving part of the gearshift lever,

or any electrical components. Liq-

uid or foreign materials may dam-

age these parts.

CAUTION

Do not put hard or breakable objects

in the pocket. If an accident occurs,

objects such as bottles, cans, etc.

can injure the occupants in the rear

seat.

EXAMPLE

5-10

OTHER CONTROLS AND EQUIPMENT

Footrest

66RH059

Use the footrest (1) as a support for your

left foot.

Floor mats (if equipped)

72M10201

To prevent the driver’s side floor mat from

sliding forward and possibly interfering with

the operation of the pedals, MARUTI genu-

ine floor mats are recommended.

Whenever you put the driver’s side floor

mat back in the vehicle after it has been

removed, hook the floor mat grommets to

the fasteners and position the floor mat

properly in the footwell.

When you replace the floor mats in your

vehicle with a different type such as all

weather floor mats, we highly recommend

to use MARUTI genuine floor mats for

proper fitting.

(1)

EXAMPLE

WARNING

Failure to take the following precau-

tions may result in the driver’s side

floor mat interfering with the pedals

and causing a loss of vehicle control

or an accident.

• Check that the floor mat grommets

are hooked to the fasteners.

• Never place additional floor mats

on top of the existing floor mat.

5-11

OTHER CONTROLS AND EQUIPMENT

Luggage compartment cover

(if equipped)

66RH060

Luggage or other cargo placed in the lug-

gage compartment is hidden from view by

a luggage compartment cover.

Luggage compartment board

66RM05001

Your vehicle is equipped with the luggage

compartment board in the luggage com-

partment.

WARNING

Do not carry items on top of the lug-

gage compartment cover, even if they

are small and light. Objects on top of

the cover could be thrown about in

an accident, causing injury, or could

obstruct the driver’s rear view.

EXAMPLE

WARNING

Objects that extend higher than the

luggage compartment cover (if

equipped) can obstruct the driver’s

rear view, which can cause an acci-

dent. These objects can also become

damaged or can damage the tailgate.

Do not carry items that extend higher

than the luggage compartment cover.

EXAMPLE

CAUTION

If you are not careful when handling

the luggage board, you could be

injured.

Handle the luggage board carefully

when removing or installing it.

NOTICE

Do not apply undue force to the

board which is held open, and do not

hold open the board while driving.

Doing so could break the board or

the interior.

5-12

OTHER CONTROLS AND EQUIPMENT

Frame hooks

Your MARUTI SUZUKI does not recom-

mend you use the frame hooks for towing

another vehicle. MARUTI SUZUKI was

originally designed to tow your vehicle on

the road for emergency towing.

If your vehicle needs to be towed in an

emergency, refer to “Towing” in the

“EMERGENCY SERVICE” section.

Front

75RM012

The towing hook (1) is provided on the

front of the vehicle for use in emergency

situations only.

To install the hook (1), follow the procedure

below.

75RM014

1) Pick up the towing hook (1), jack handle

(A) and wheel brace (B) in the luggage

compartment.

75RM015

2) Remove the cover (C) by using a jack

handle (A) covered with a soft cloth as

shown in the illustration.

NOTE:

Do not use excessive force as it may dam-

age the cover strap.

WARNING

Observe the following instructions

when using frame hooks. The towing

hook or vehicle body may break and

cause serious injury or damage:

• Do not use the frame hooks for

towing another vehicle.

• Avoid pulling the vehicle to get out

of severe snowy, muddy or sandy

conditions, sudden starts or erratic

driving maneuvers which could

cause excessive stress on the tow-

ing hook.

In such case, we recommend that

you contact a professional service.

(1)

EXAMPLE

(1)

(A)

(B)

EXAMPLE

(A)

(C)

EXAMPLE

5-13

OTHER CONTROLS AND EQUIPMENT

75RM016

3) Install the towing hook (1) by hand.

NOTE:

We recommend that fasten the cover with

tape to prevent damage during towing.

75RM017

4) To tighten the towing hook (1), turn it

clockwise by using a wheel brace (B)

until the hook (1) is securely installed.

To remove the towing hook (1), reverse the

installation procedure.

Rear

75RM018

The frame hook (2) is provided on the rear

of the vehicle for use in emergency situa-

tions and sea shipping purposes only.

Other holes

66RM05002

The frame holes (3) are provided only for

transporting by a car carrier trailer.

(1)

EXAMPLE

(B)

(1)

EXAMPLE

NOTICE

When you use the frame hook (2),

avoid the driving that gives signifi-

cant physical shock on hook. Such

operation can damage the hook, the

vehicle body or the drive system.

• Do not accelerate suddenly.

• Do not tow the vehicle heavier than

your vehicle.

(2)

EXAMPLE

WARNING

Do not use the frame holes (3) for

towing purpose. These holes may

break and cause serious injury or

damage.

(3) (3)

EXAMPLE

5-14

OTHER CONTROLS AND EQUIPMENT

Heating and air conditioning system

There are two types of air conditioning systems as follows:

• Manual heating and air conditioning system (if equipped)

• Automatic heating and air conditioning system (climate control) (if equipped)

Air outlet

66RH131

1. Windshield defroster outlet

2. Side defroster outlet

3. Side outlet

4. Center outlet

5. Floor outlet

EXAMPLE

Side outlet

75RM019

When open, air comes out regardless of

the air flow selector position.

EXAMPLE

5-15

OTHER CONTROLS AND EQUIPMENT

Center outlet

66RH123

Move the knob (1) horizontally or the case

(2) vertically to adjust the direction of air-

flow as desired.

CAUTION

Prolonged exposure to hot air from

the heater or air conditioner could

result in low temperature burns. All

vehicle occupants, particularly chil-

dren, the elderly, those with special

needs, individuals with delicate skin,

and sleeping individuals, should

maintain sufficient distance from the

air outlets to prevent prolonged

exposure to hot airflow.

(1) (2)

EXAMPLE

Manual heating and air conditioning system

Description of controls

75RM060

Temperature selector (1)

This is used to select the temperature by turning the selector.

Blower speed selector (2)

This is used to turn on the blower and to select blower speed by turning the selector.

(3) (1)(4)

(2) (5)

EXAMPLE

5-16

OTHER CONTROLS AND EQUIPMENT

Air flow selector (3)

75RM022

This is used to select one of the following

functions.

VENTILATION (a)

66RH132

Temperature-controlled air comes out of

the center and side air outlets.

BI-LEVEL (b)

66RH133

Temperature-controlled air comes out of

the floor outlets and cooler air comes out

of the center and side outlets. When the

temperature selector (1) is in the fully cold

position or fully hot position, however, the

air from the floor outlets and the air from

the center and side outlets will be the

same temperature.

HEAT (c)

66RH134

Temperature-controlled air comes out of

the floor outlets and the side outlets, also

comes out of the windshield defroster out-

lets and also comes slightly out of the side

defroster outlets.

HEAT & DEFROST (d)

66RH135

Temperature-controlled air comes out of

the floor outlets, the windshield defroster

outlets, the side defroster outlets and the

side outlets.

DEFROST (e)

66RH136

Temperature-controlled air comes out of

the windshield defroster outlets, the side

defroster outlets and the side outlets.

(a)

(b)

(e)

(d)

(c)

EXAMPLE

5-17

OTHER CONTROLS AND EQUIPMENT

Air intake selector (4)

75RM059

This selector is used to select the following

modes.

FRESH AIR (f)

When this mode is selected by moving the

lever to right, outside air is used.

RECIRCULATED AIR (g)

When this mode is selected by moving the

lever to left, outside air is shut out and

inside air is recirculated. This mode is suit-

able when driving through dusty or polluted

air such as in a tunnel, or when attempting

to quickly cool down the interior.

NOTE:

If you select RECIRCULATED AIR for an

extended period of time, the air in the vehi-

cle can become contaminated. Therefore,

you should occasionally select FRESH

AIR.

Air conditioning switch (5)

To turn on the air conditioning system, set

the blower speed selector to a position

other than off and push in “A/C” switch (5).

With this “A/C” switch operation, a indica-

tor light will come on when the air condi-

tioning system is on. To turn off the air

conditioning system, push “A/C” switch

again.

During operation of the air conditioner, you

may notice slight changes in engine

speed. These changes are normal, the

system is designed so that the compressor

turns on or off to maintain the desired tem-

perature.

Less operation of the compressor results

in better fuel economy.

System operating instructions

Natural ventilation

Select VENTILATION and FRESH AIR, the

temperature selector to the desired tem-

perature position, and the blower speed

selector to off. Fresh air will flow through

the vehicle during driving.

Forced ventilation

The control settings are the same as for

natural ventilation except you set the

blower speed selector to a position other

than off.

Normal heating (using outside air)

Select HEAT and FRESH AIR, the tem-

perature selector to the desired tempera-

ture position and the blower speed selector

to the desired blower speed position. Set-

ting the blower speed selector to a higher

blower speed position increases heating

efficiency.

Quick heating (using recirculated air)

The control settings are the same as for

normal heating except you select RECIR-

CULATED AIR. If you use this heating

method for an extended period of time, the

air in the vehicle can become contami-

nated and the windows can become misty.

Therefore, use this method only for quick

heating and change to the normal heating

method as soon as possible.

(g) (f)

EXAMPLE

5-18

OTHER CONTROLS AND EQUIPMENT

Head cooled/Feet warmed heating

Select BI-LEVEL and FRESH AIR, the

temperature selector to the desired tem-

perature position, and the blower speed

selector to the desired blower speed posi-

tion. Unless the temperature selector is in

the fully cold position or fully hot position,

the air that comes out of the center and

side outlets will be cooler than the air that

comes out of the floor outlets.

Normal cooling

Set the air flow selector to VENTILATION,

the temperature selector to the desired tem-

perature position and the blower speed

selector to the desired blower speed posi-

tion, and turn on “A/C” switch. Setting the

blower speed selector to a higher blower

speed position increases cooling efficiency.

You can switch the air intake selector to

either FRESH AIR or RECIRCULATED

AIR as you desire. Choosing RECIRCU-

LATED AIR increases cooling efficiency.

Quick cooling (using recirculated air)

The control settings are the same as for

normal cooling except you select RECIR-

CULATED AIR and the highest blower

speed.

NOTE:

• If you select RECIRCULATED AIR for an

extended period of time, the air in the

vehicle can become contaminated.

Therefore, you should occasionally

select FRESH AIR.

• If your vehicle has been left in the sun

with the windows closed, it will cool

faster if you open the windows briefly

while you operate the air conditioner with

the air intake selector at FRESH AIR and

the blower at high speed.

Dehumidifying

Set the air flow selector to a desired air

flow selector position, the temperature

selector to the desired temperature posi-

tion and the blower speed selector to the

desired blower speed position. Also select

FRESH AIR and turn on “A/C” switch.

NOTE:

Because the air conditioner dehumidifies

the air, turning it on will help keep the win-

dows clear, even when blowing heated air

using DEFROST or HEAT & DEFROST

functions.

66RH137

NOTE:

If you need maximum defrosting:

• select DEFROST and FRESH AIR,

• set the blower speed selector to high,

• adjust the temperature selector to the

hot end,

• turn on “A/C” switch, and

• adjust the side outlets so the air blows

on the side windows.

EXAMPLE

5-19

OTHER CONTROLS AND EQUIPMENT

Maintenance

If you do not use the air conditioner for a

long period, such as during winter, it may

not give the best performance when you

start using it again. To help maintain opti-

mum performance and durability of your air

conditioner, it needs to be run periodically.

Operate the air conditioner at least once a

month for one minute with the engine

idling. This circulates the refrigerant and oil

and helps protect the internal components.

If your air conditioner is equipped with air

filters, clean or replace them as specified

in “Maintenance schedule” in the

“INSPECTION AND MAINTENANCE” sec-

tion. Have this job done by your authorised

Maruti Suzuki workshop as the lower glove

box must be lowered for this job.

NOTE:

Your vehicle uses the air conditioning

refrigerant HFC-134a, commonly called

R-134a. R-134a replaced R-12 around

1993 for automotive applications. Other

refrigerants are available, including recy-

cled R-12, but only R-134a should be used

in your vehicle.

NOTICE

Using the wrong refrigerant may

damage your air conditioning sys-

tem. Use R-134a only. Do not mix or

replace the R-134a with other refrig-

erants.

Automatic heating and air conditioning system

(climate control) (if equipped)

Description of controls

75RM025

(1) Temperature selector

(2) Blower speed selector

(3) Air intake selector

(4) Air flow selector

(5) Defrost switch

(6) Air conditioning switch

(7) “OFF” switch

(8) “AUTO” switch

(9) Display

(5)(8)(7)(6)(3) (4)

(1) (9) (2)

EXAMPLE

5-20

OTHER CONTROLS AND EQUIPMENT

Temperature selector (1)

75RM026

Push the temperature selector (1) up or

down to adjust the temperature.

NOTE:

If you push the temperature selector (1)

until “HI” or “LO” appears on the display,

the climate control system will operate at

maximum heating or cooling. The tempera-

ture of the air from the outlets may change

suddenly while “LO” or “HI” is displayed,

but this is normal.

NOTE:

When you change the unit of temperature

in the information display, the unit of tem-

perature in the air conditioning system will

be changed. Refer to “Information display

(instrument cluster with tachometer)” in the

“BEFORE DRIVING” section for details.

Blower speed selector (2)

75RM027

The blower speed selector (2) is used to

turn on the blower and to select blower

speed.

If “AUTO” switch (8) is pushed, the blower

speed will vary automatically as the cli-

mate control system maintains the

selected temperature.

Air intake selector (3)

75RM028

Push the air intake selector (3) to change

between the following modes.

If “AUTO” switch (8) is pushed, the air

intake will vary automatically as the climate

control system maintains the selected tem-

perature.

NOTE:

When you select the recirculated air mode,

the automatic operation system is deacti-

vated if you push “AUTO” switch (8).

RECIRCULATED AIR (a)

When this mode is selected, outside air is

shut off and inside air is recirculated. This

mode is suitable when driving through an

area with polluted air such as a tunnel, or

when attempting to quickly cool down the

vehicle.

(1)

EXAMPLE

(2)

EXAMPLE

(3)

(b)

(a)

EXAMPLE

5-21

OTHER CONTROLS AND EQUIPMENT

FRESH AIR (b)

When this mode is selected, outside air is

introduced.

FRESH AIR and RECIRCULATED AIR are

selected alternately each time the air

intake selector is pushed.

NOTE:

If you select RECIRCULATED AIR for an

extended period of time, the air in the vehi-

cle can become contaminated. Therefore,

you should occasionally select FRESH

AIR.

Air flow selector (4)

75RM029

Push the air flow selector (4) to change

among the following functions. The indica-

tion of the selected mode appears on the

display.

If “AUTO” switch (8) is pushed, the air flow

will vary automatically as the climate con-

trol system maintains the selected tem-

perature.

VENTILATION (c)

66RH132

Temperature-controlled air comes out of

the center, side and rear air outlets.

BI-LEVEL (d)

66RH133

Temperature-controlled air comes out of

the floor outlets and cooler air comes out

of the center, side and rear outlets. When

the temperature selector (1) is in the fully

cold position or fully hot position, however,

the air from the floor outlets and the air

from the center, side and rear outlets will

be the same temperature.

(4)

(c)

(d)

(e)

(f)

EXAMPLE

5-22

OTHER CONTROLS AND EQUIPMENT

HEAT (e)

66RH134

Temperature-controlled air comes out of

the floor outlets and the side outlets, a

small amount of air comes out of the wind-

shield defroster outlets and also comes

slightly out of the side defroster outlets.

HEAT & DEFROST (f)

66RH138

Temperature-controlled air comes out of

the floor outlets, the windshield defroster

outlets, the side defroster outlets and the

side outlets.

Defrost switch (5)

75RM030

Push the defrost switch (5) to turn on the

defroster.

DEFROST

66RH136

Temperature-controlled air comes out of

the windshield defroster outlets, the side

defroster outlets and the side outlets.

NOTE:

When the defrost switch (5) is pushed to

turn on the defroster, the air conditioning

system will come on and FRESH AIR

mode will be selected automatically. In

very cold weather, however, the air condi-

tioning system will not turn on.

Air conditioning switch (6)

75RM031

The air conditioning switch (6) is used to

turn on and off the air conditioning system

only when the blower is on. To turn on the

air conditioning system, push in the switch

and “A/C” will appear on the display. To

turn off the air conditioning system, push in

the switch again and “A/C” will go off.

EXAMPLE

(5)

EXAMPLE

(6)

EXAMPLE

5-23

OTHER CONTROLS AND EQUIPMENT

System operating instructions

Automatic operation

75RM032

You can let the climate control system work

automatically. To set the system for fully-auto-

matic operation, follow the procedure below.

1) Start the engine.

2) Push “AUTO” switch (8).

3) Set the desired temperature by pushing

the temperature selector (1).

The blower speed, air intake and air flow

are controlled automatically to maintain the

set temperature. However, the air flow is

not changed to DEFROST position auto-

matically.

NOTE:

When you select the recirculated air mode,

the automatic operation system is deacti-

vated if you push “AUTO” switch (8).

You can use the air conditioning switch (6)

to manually turn the air conditioner on or off

according to your preference. When you

turn the air conditioning switch off, the cli-

mate control system cannot lower the inside

temperature below outside temperature.

To turn the climate control system off, push

“OFF” switch (7).

NOTE:

If “AUTO” on the display blinks, there is a

problem in the heating system and/or air

conditioning system. You should have the

system inspected by an authorised Maruti

Suzuki workshop.

NOTE:

• To find the temperature at which you are

most comfortable, start with the 25°C

(75°F) setting.

• If you push the temperature selector (1)

until “HI” or “LO” appears on the display,

the climate control system will operate at

maximum heating or cooling and the

blower will run at full speed.

• To avoid blowing cold air in cold weather

or hot air in hot weather, the system will

delay turning on the blower until warmed

or chilled air is available.

• If your vehicle has been left in the sun

with the windows closed, it will cool

faster if you open the windows briefly.

• Even under the automatic operation, you

can set individual selectors to the manual

mode. The manually selected functions

are maintained, and the other functions

remain under automatic operation.

• If the windshield and/or the front door

windows are fogged, push the defrost

switch (5) to turn on the defroster, or

push the air flow selector (4) to change

the air flow to HEAT & DEFROST posi-

tion to defog the windows.

• To return the blower speed selector (2),

air intake selector (3), and air flow selec-

tor (4) to automatic operation, push

“AUTO” switch (8).

66RH124

Be careful not to cover the interior tem-

perature sensor (10) located between the

steering wheel and the climate control

panel, or the solar sensor (11) located at

the top of the driver’s side dashboard.

These sensors are used by the automatic

system to regulate temperature.

(8)(7)(6)

(1)

EXAMPLE

(10)

(11)

EXAMPLE

5-24

OTHER CONTROLS AND EQUIPMENT

Manual operation

You can manually control the climate con-

trol system. Set the selectors to the

desired positions.

66RH137

NOTE:

If you need maximum defrosting:

• push the defrost switch (5) to turn on the

defroster (the air conditioning system will

come on and FRESH AIR mode will be

selected automatically),

• set the blower speed selector to high,

• adjust the temperature selector to “HI”

indication on the display, and

• adjust the side outlets so the air blows

on the side windows.

Maintenance

If you do not use the air conditioner for a

long period, such as during winter, it may

not give the best performance when you

start using it again. To help maintain opti-

mum performance and durability of your air

conditioner, it needs to be run periodically.

Operate the air conditioner at least once a

month for one minute with the engine

idling. This circulates the refrigerant and oil

and helps protect the internal components.

If your air conditioner is equipped with air

filters, clean or replace them as specified

in “Maintenance schedule” in the

“INSPECTION AND MAINTENANCE” sec-

tion. Have this job done by your authorised

Maruti Suzuki workshop as the lower glove

box must be lowered for this job.

NOTE:

Your vehicle uses the air conditioning

refrigerant HFC-134a, commonly called

R-134a. R-134a replaced R-12 around

1993 for automotive applications. Other

refrigerants are available, including recy-

cled R-12, but only R-134a should be used

in your vehicle.

Radio antenna

75RM301

The radio antenna on the roof is remov-

able. To remove the antenna, turn it coun-

terclockwise. To reinstall the antenna, turn

it clockwise firmly by hand.

EXAMPLE

NOTICE

Using the wrong refrigerant may

damage your air conditioning sys-

tem. Use R-134a only. Do not mix or

replace the R-134a with other refrig-

erants.

NOTICE

To avoid damage to the radio

antenna:

• Remove the antenna when using an

automatic car wash.

• Remove the antenna when the

antenna hits anything such as a

low ceiling in a parking garage or

putting a car cover over your vehi-

cle.

EXAMPLE

5-25

OTHER CONTROLS AND EQUIPMENT

Installation of radio frequency

transmitters

We recommend that you always ask a

authorised Maruti Suzuki workshop about

frequency band, max output power,

antenna position at vehicle and specific

conditions for installation and/or use before

installing a radio transmitter in your vehi-

cle. Such equipments may cause the elec-

tronic control system to malfunction if they

are incorrectly installed or they are not

suited for the vehicle.

Audio system (if equipped)

66RH070

AM/FM CD player with Bluetooth

function

NOTE:

For vehicle equipped with SMARTPLAY INFOTAINMENT SYSTEM, refer to the audio

manual available with the vehicle.

EXAMPLE

5-26

OTHER CONTROLS AND EQUIPMENT

Safety information Notes on discs

Precautions

• When the inside of the vehicle is very

cold and the player is used soon after

switching on the heater, condensation

may form on the disc or the optical

parts of the player and proper playback

may not be possible. If condensation

forms on the disc, wipe it off with a soft

cloth. If condensation forms on the opti-

cal parts of the player, do not use the

player for about one hour. This will

allow the condensation to disappear

normally.

• Driving on extremely bumpy roads

which cause severe vibrations may

cause sound to skip.

• This unit uses a precision mechanism.

Even in the event that trouble arises,

never open the case, disassemble the

unit, or lubricate the rotating parts.

Bring the unit to an authorised Maruti

Suzuki workshop.

Cautions on handling

52D274

This unit has been designed specifically for

playback of compact discs bearing mark

(A) shown above.

No other discs can be played.

52D275

To remove the compact disc from its stor-

age case, press down on the center of the

case and lift the disc out, holding it care-

fully by the edges.

Always handle the compact disc by the

edges.

Never touch the surface.

WARNING

If you pay too much attention to

operating the audio system or view-

ing the audio system display while

driving, an accident can occur. If

you set the sound volume too loud,

it could prevent you from being

aware of road and traffic conditions.

• Keep your eyes on the road and

your mind on the drive. Avoid pay-

ing too much attention to operat-

ing the audio system or viewing

the audio system display.

• Familiarize yourself with the audio

system controls and operation of

the audio system before driving.

• Preset your favorite radio stations

before driving so that you can

quickly tune to them using the

presets.

• Set the sound volume to a level

that will allow you to continue to

be aware of road and traffic condi-

tions while driving.

(A)

(

)

EXAMPLE

Removing the disc

Proper way to hold

the compact disc

EXAMPLE

5-27

OTHER CONTROLS AND EQUIPMENT

52D347

To remove fingermarks and dust, use a

soft cloth, and wipe in a straight line from

the center of the compact disc to the cir-

cumference.

52D277

New discs may have some roughness

around the edges. The unit may not work

or the sound may skip if such discs are

used. Use a ball-point pen (B), etc. to

remove the roughness (C) from edges of

the disc before inserting it into the unit.

52D348

Never stick labels on the surface of the

compact disc or write on the surface with a

pencil or pen.

52D349

Do not use any solvents such as commer-

cially available cleaners, anti-static spray,

or thinner to clean compact discs.

52D350

Do not use compact discs that have large

scratches, are misshaped, or cracked, etc.

Use of such discs will cause damage or

prevent the system from operating prop-

erly.

52D351

Do not expose compact discs to direct sun-

light or any heat source.

EXAMPLE

(B)

(C)

(

)

(

)

(C)

EXAMPLE

5-28

OTHER CONTROLS AND EQUIPMENT

NOTE:

• Do not use commercially available CD

protection sheets or discs equipped with

stabilizers, etc.

These may get caught in the internal

mechanism and damage the disc.

• It may be impossible to play CD-R discs

with this unit due to the recording condi-

tions.

• CD-RW discs cannot be played with this

unit.

The Bluetooth

word mark and logo are

registered trademarks and are owned by

the Bluetooth SIG, Ink.

Stop using this unit and a Bluetooth

ready device whenever requested.

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

You should stop using this unit whenever

you are notified that your unit disturbs

other wireless communication immediately.

WARNING

This is a class I laser product. Use

of controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by your-

self.

Ask an authorized dealer for the

repair.

5-29

OTHER CONTROLS AND EQUIPMENT

Basic operations

66RH071

(1) “VOL PUSH PWR” knob

(2) “TUNE/FLD PUSH SOUND” knob

(2) (1)

EXAMPLE

Turning on/off power

Press “VOL PUSH PWR” knob (1) to turn

on the power. The unit starts to operate in

the previous setting that the power was

turned off.

Adjusting the volume

Turn “VOL PUSH PWR” knob (1).

Turning it clockwise increases the volume;

turning it counterclockwise decreases the

volume.

NOTE:

For the purposes of safe driving, adjust the

audio volume to a level that allows you to

hear sounds outside of the vehicle includ-

ing car horns and particularly emergency

vehicle sirens.

5-30

OTHER CONTROLS AND EQUIPMENT

Adjusting bass/treble/balance/fader

1) Press “TUNE/FLD PUSH SOUND”

knob (2).

Each time the knob is pressed, sound

adjustment will change as follows:

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to adjust the sound.

Adjusting the AVC (Auto volume con-

trol)

The Auto Volume Control (AVC) function

automatically adjusts (increases/

decreases) the sound volume in accor-

dance with vehicle speed. The AVC control

is provided with three selectable levels

(LEVEL OFF, 1, 2, 3). The range of volume

adjustment increases together with the

LEVEL number.

1) Press “TUNE/FLD PUSH SOUND”

knob (2) until the AVC adjustment mode

is selected.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select the desired AVC adjust-

ment level (Initial setting: LEVEL 2).

Preset-EQ

Preset-EQ calls up various sound types in

accordance with the listening music type.

1) Press “TUNE/FLD PUSH SOUND”

knob (2) several times until “PRESET-

EQ” appears.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2).

Each time the knob is turned, preset

EQ mode will change as follows:

Preset-EQ (EQ OFF)

Bass adjustment (BASS 0)

Treble adjustment (TREBLE 0)

Balance adjustment (BALANCE 0)

Fader adjustment (FADER 0)

AVC adjustment (AVC LEVEL 2)

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

5-31

OTHER CONTROLS AND EQUIPMENT

Listening to the radio

66RH072

(3)

(4)

(6)

(1)

(2)

(7)

(5)

EXAMPLE

Display

(1) “FM” button

(2) “AM” button

(3) UP button

(4) DOWN button

(5) “TUNE/FLD PUSH SOUND” knob

(6) PRESET buttons ([1] to [6])

(7) “AS” button

(A) Band

(B) Frequency

(A)

(B)

5-32

OTHER CONTROLS AND EQUIPMENT

Selecting the FM band

Press “FM” button (1).

Each time the button is pressed, the recep-

tion band will change as follows:

Selecting the AM band

Press “AM” button (2).

Seek tuning

Press UP button (3) or DOWN button (4).

The unit stops searching for a station at a

frequency where a broadcast station is

available.

Manual tuning

Turn “TUNE/FLD PUSH SOUND” knob (5).

The frequency being received is displayed.

Preset memory

1) Select the desired station.

2) Hold down a desired button ([1] to [6])

of the PRESET buttons (6) to which you

want to store the station for 2 seconds

or longer.

Auto store

Hold down “AS” button (7) for 2 seconds or

longer.

6 stations in good reception will automati-

cally be stored to PRESET buttons (6) in

order, starting from a station whose fre-

quency is the lowest.

NOTE:

• Auto store can be released by pressing

“AS” button (7) while auto store is under

way.

• When the auto store is performed, the

station previously stored in the memory

at the position is overwritten.

• When there are fewer than 6 stations

that can be stored even if 1 round of

auto store operation is performed, no

station will be stored at the remaining

PRESET buttons (6).

• 6 stations can be preset for FM1 and

FM2 in common, and 6 stations for AM

in auto store mode.

Auto store mode on/off

Press “AS” button (7).

Each time the button is pressed, the mode

is switched as follows:

Radio reception

Radio reception can be affected by envi-

ronment, atmospheric conditions, or radio

signal’s power and distance from the sta-

tion. Nearby mountains and buildings may

interfere or deflect radio reception, causing

poor reception. Poor reception or radio

static can also be caused by electric cur-

rent from overhead wires or high voltage

power lines.

FM1 FM2

AS mode on AS mode off

5-33

OTHER CONTROLS AND EQUIPMENT

Listening to a CD

66RH073

(4)

(2)

(5)

(8)

(3)

(6) (7)

(1)

EXAMPLE

Display

(1) Insertion slot

(2) EJECT button

(3) “CD” button

(4) UP button

(5) DOWN button

(6) “RPT” button

(7) “RDM” button

(8) “DISP” button

(A) Track number

(B) Play time

NOTE:

This product does not support 8 cm CD

(sometimes called as “mini single CD”, “3-

inch CD”, “CD3”, etc.).

(B)

(A)

5-34

OTHER CONTROLS AND EQUIPMENT

• CDs or CD-ROMs without mark (A) can-

not be used.

• Some discs recorded in CD-R/CD-RW

format may sometimes be impossible to

use.

• A CD is to be inserted with its label side

up.

• When there is a CD already in the unit, it

is impossible to insert another CD with-

out ejecting the CD in the unit. Do not

use force to insert a CD into the CD

insertion slot.

Loading a CD

Insert a CD in the insertion slot (1).

When the CD is loaded, it starts to play.

Ejecting a CD

Press EJECT button (2).

When the ignition switch is in “LOCK” posi-

tion or the engine switch is in LOCK (OFF)

mode, the CD remained ejected for around

15 seconds or longer will automatically be

drawn inside the unit (Auto reload func-

tion).

The backup eject function:

This function allows you to eject a CD by

pressing EJECT button (2) even when the

ignition switch is in “LOCK” position or the

engine switch is in LOCK (OFF) mode.

Listening to a CD

When a CD is inserted, playback will auto-

matically start.

When a CD is already inside the unit,

press “CD” button (3) to start playback.

Selecting a track

• Press UP button (4) to listen to the next

track.

• Press DOWN button (5) twice to listen to

the previous track.

When DOWN button (5) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (4) to fast forward

the track.

• Hold down DOWN button (5) to fast

rewind the track.

(A)

(

)

EXAMPLE

NOTICE

• Never insert your finger or hand

into the CD insertion slot. Never

insert foreign objects.

• Never insert a CD with glue coming

out from adhesive tape or a rental

CD label or with a trace indicating

that adhesive tape or a rental CD

label has been removed. This may

cause the CD not to eject or result

in a malfunction.

NOTICE

If you forcefully try to push an

ejected CD inside the unit before auto

reloading, the disc surface might be

scratched.

Before reloading a CD, remove it

from the unit completely.

5-35

OTHER CONTROLS AND EQUIPMENT

Random playback

Press “RDM” button (7).

Each time the button is pressed, the mode

will change as follows:

• TRACK RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

Repeat playback

Press “RPT” button (6).

Each time the button is pressed, the mode

will change as follows:

• TRACK REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Display change

Press “DISP” button (8).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (8) for

1 second or longer can display the next

page.

OFF TRACK RANDOM

OFF TRACK REPEAT

Play time

Disc title

Track title

5-36

OTHER CONTROLS AND EQUIPMENT

Listening to an MP3/WMA/AAC disc

66RH074

(2)

(3)

(1)

(6) (4) (5)

EXAMPLE

Display

(1) “TUNE/FLD PUSH SOUND” knob

(2) UP button

(3) DOWN button

(4) “RPT” button

(5) “RDM” button

(6) “DISP” button

(A) Folder number

(B) Track number

(D) File type

(C)

(B)(A)

(D)

5-37

OTHER CONTROLS AND EQUIPMENT

Selecting a folder

Turn “TUNE/FLD PUSH SOUND” knob (1)

to select a folder.

Selecting a track

• Press UP button (2) to listen to the next

track.

• Press DOWN button (3) twice to listen to

the previous track.

When DOWN button (3) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (2) to fast forward

the track.

• Hold down DOWN button (3) to fast

rewind the track.

Random playback

Press “RDM” button (5).

Each time the button is pressed, the mode

will change as follows:

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the current folder will be

played in random order.

• ALL RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

Repeat playback

Press “RPT” button (4).

Each time the button is pressed, the mode

will change as follows:

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

• FOLDER REPEAT

The repeat indicator “F.RPT” will light.

All tracks in the currently selected folder

will be played repeatedly.

OFF FOLDER RANDOM ALL RANDOM

OFF FILE REPEAT FOLDER REPEAT

5-38

OTHER CONTROLS AND EQUIPMENT

Display change

Press “DISP” button (6).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (6) for

1 second or longer can display the next

page.

Notes on MP3/WMA/AAC

What is MP3?

• An abbreviation of “MPEG audio layer3”,

MP3 is an audio compression format

that has become the standard format

among PC users. Its merit is that the

original audio data is compressed to

approximately 1/10 and high sound qual-

ity is maintained. This means that it is

possible to store the data of approxi-

mately 10 music CDs on a single CD-R/

RW disc, which in turn makes it possible

to play music for a long time without hav-

ing to change the disc.

What is WMA?

• An abbreviation of “Windows Media

Audio,” WMA is an audio compression

format developed by Microsoft.

• WMA files for which the DRM (Digital

Rights Management) function is on can-

not be played.

• Windows Media

and the Windows

logo are trademarks or registered trade-

marks of Microsoft Corporation in the

United States and other countries.

What is AAC?

• An abbreviation of “Advanced Audio

Coding,” AAC is an audio compression

format used by MPEG2 and MPEG4.

Points to remember when making

MP3/WMA/AAC files

Common

• High bit rate and high sampling fre-

quency are recommended for high qual-

ity sounds.

• Selecting VBR (Variable Bit Rate) is not

recommended. Selecting VBR may

cause display of incorrect playing time

and jumpiness of playback.

• Playback sound quality varies depend-

ing on the encoding environment. For

details, refer to the user manual of the

encoding software and the writing soft-

ware in use.

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

NOTICE

Never use “.mp3”, “.wma” or “.m4a”

as a file name extension if it is not in

the MP3/WMA/AAC format file. Fail-

ure to observe this may result in

damage to the speaker due to noise

production.

5-39

OTHER CONTROLS AND EQUIPMENT

Recording MP3/WMA/AAC files on a CD

media

• It is recommended not to write both CD-

DA files and MP3/WMA/AAC files on a

disc.

• If both CD-DA files and MP3/WMA/AAC

files are on the same disc, tracks may

not be played in the correct order or

some tracks may not be played at all.

• When storing both MP3 data and WMA

data on the same disc, sort and place

them in different folders.

• Do not write files other than MP3/WMA/

AAC files and unnecessary folders on a

disc.

• MP3/WMA/AAC files should be named

to meet the standards and the file sys-

tem specifications as shown below.

• The file extension “.mp3”, “.wma” or

“.m4a” should be assigned to files based

on their format independently.

• You may encounter a trouble in playing

MP3/WMA/AAC files or displaying infor-

mation of MP3/WMA/AAC files depend-

ing on the writing software or CD

recorder in use.

• This unit does not have a playlist func-

tion.

• It is recommended to write discs in Disc-

at-Once mode even though Multi-ses-

sion mode is supported. These modes

are the methods for writing audio data in

CD.

Compression formats

MP3

• Bit rate

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

MPEG1 Audio Layer III: 32 k/44.1 k/

48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/

24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/

12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Supported file systems

ISO 9660 Level 1/Level 2, Joliet, Romeo

Maximum number of files/folders

• Maximum number of files: 512

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-40

OTHER CONTROLS AND EQUIPMENT

Listening to files stored in a USB device

66RH075

(3)

(4)

(1)

(2)

(7) (5) (6)

EXAMPLE

Display

(1) “MEDIA” button

(2) “TUNE/FLD PUSH SOUND” knob

(3) UP button

(4) DOWN button

(5) “RPT” button

(6) “RDM” button

(7) “DISP” button

(A) Folder number

(B) Track number

(D) File type

NOTICE

Do not connect any USB device other

than a USB memory or a USB audio

player. Do not connect multiple USB

devices to the USB connector using a

USB hub, etc. Supplying power to

multiple USB devices from the con-

nector could cause overheating and

smoking.

(C)

(B)(A)

(D)

5-41

OTHER CONTROLS AND EQUIPMENT

Selecting a USB device mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a folder

Turn “TUNE/FLD PUSH SOUND” knob (2)

to select the desired folder.

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

Random playback

Press “RDM” button (6).

Each time the button is pressed, the mode

will change as follows:

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the currently selected

folder will be played in random order.

• ALL RANDOM

The random indicator “RDM” will light.

The tracks in the connected USB device

will be played in random order.

Repeat playback

Press “RPT” button (5).

Each time the button is pressed, the mode

will change as follows:

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

• FOLDER REPEAT

The repeat indicator “F.RPT” will light.

All the tracks in the folder currently

selected will be played repeatedly.

Display change

Press “DISP” button (7).

Each time the button is pressed, display

will change as follows:

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the file currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (7) for

1 second or longer can display the next

page.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

OFF FOLDER RANDOM ALL RANDOM

OFF FILE REPEAT FOLDER REPEAT

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

5-42

OTHER CONTROLS AND EQUIPMENT

Notes on USB device

Compatible USB devices

• USB mass storage class.

For details as to whether your USB

memory/USB audio is compatible with

USB mass storage class, please contact

the USB memory/USB audio manufac-

turer.

• USB standard compatibility 1.1/2.0 full

speed.

• File system FAT12/16/32, VFAT.

• Maximum current less than 1.0 A.

• If devices such as USB hub, extension

cable are connected to the audio sys-

tem, it may not be recognized. In such

case, connect the USB device directly to

the audio system.

• Devices such as MP3 player/mobile

phone/digital camera may not be recog-

nized by the audio system for playing

music.

USB device connection

• When connecting a USB device, check

that the connector is pushed all the way

into the port.

• Do not leave the USB device for long

periods of time inside the vehicle where

the temperature can rise too high.

• Back up any important data beforehand.

We cannot accept responsibility for any

lost data.

• It is recommended not to connect a USB

device that contains data files other than

MP3/WMA/AAC format.

Recording MP3/WMA/AAC files on a

USB device

• Playback or display may not be possible

depending on the type of USB device in

use or the condition of the recording.

• Depending on the connected USB mem-

ory, the files may be played in different

order from the stored one.

Compression formats

MP3

• Bit rate

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

MPEG1 Audio Layer III: 32 k/44.1 k/48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Maximum number of files/folders

• Maximum number of files: 2500

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-43

OTHER CONTROLS AND EQUIPMENT

Listening to an iPod

66RH076

(3)

(4)

(1)

(7) (5) (6)

(2)

(8)

EXAMPLE

Display

(1) “MEDIA” button

(2) “TUNE/FLD PUSH SOUND” knob

(3) UP button

(4) DOWN button

(5) “RPT” button

(6) “RDM” button

(7) “DISP” button

(8) PRESET buttons ([1] to [6])

(A) Track title

(B) Track number

(C)

(A)

(B)

5-44

OTHER CONTROLS AND EQUIPMENT

Selecting an iPod

mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

Random playback

Press “RDM” button (6).

Each time the button is pressed, the mode

will change as follows:

• SONG RANDOM

The random indicator “RDM” will light.

The tracks in the iPod

will be played in

random order.

• ALBUM RANDOM

The random indicator “F.RDM” will light.

The albums in the iPod

will be played in

random order.

Repeat playback

Press “RPT” button (5).

Each time the button is pressed, the mode

will change as follows:

• SONG REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Display change

Press “DISP” button (7).

Each time the button is pressed, display

will change as follows:

NOTE:

If text data contains more than 16 charac-

ters, “>” mark will appear at the right end.

Holding down “DISP” button (7) for 1 sec-

ond or longer can display the next page.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

OFF SONG RANDOM ALBUM RANDOM

OFF SONG REPEAT

Playlist name /

Track title (Playlist mode only)

Artist name /

Track title

Album name /

Track title

Track title /

Play time

5-45

OTHER CONTROLS AND EQUIPMENT

Playing mode selection

1) Press the button numbered [6] of PRE-

SET buttons (8) for 1 second or longer.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2).

Each time the knob is turned, the mode

will change as follows:

3) Press “TUNE/FLD PUSH SOUND”

knob (2) to select the desired mode.

NOTE:

• When the button numbered [6] of PRE-

SET buttons (8) is pressed, the previous

mode will be displayed.

Notes on iPod

Supported iPod

• iPod

touch (6th generation)

• iPod

touch (5th generation)

• iPod

touch (4th generation)

• iPod

touch (3rd generation)

• iPod

touch (2nd generation)

• iPod

touch (1st generation)

• iPod

classic

• iPod

nano (7th generation)

• iPod

nano (6th generation)

• iPod

nano (5th generation)

• iPod

nano (4th generation)

• iPod

nano (3rd generation)

• iPod

nano (2nd generation)

• iPod

nano (1st generation)

• iPod

(5th generation)

• iPhone

6S Plus

• iPhone

6 Plus

• iPhone

3GS

• iPhone

* Some functions may not be available

depending on the model of iPod

* iPod

is a trademark of Apple Inc., regis-

tered in the U.S. and other countries.

* iPhone

is a trademark of Apple Inc.,

registered in the U.S. and other coun-

tries.

* Apple is not responsible for the opera-

tion of this device or its compliance with

safety and regulatory standards.

iPod

connection

• Make sure to detach the iPod

after

turning the ignition switch to “LOCK”

position or pressing the engine switch to

change the ignition mode to LOCK

(OFF). The iPod

may not be shut down

when it is being connected and may

result in battery depletion.

• Do not connect iPod

accessories such

as an iPod

remote control or head-

phones while connecting the iPod

with

the unit. The unit may not operate cor-

rectly.

PLAYLIST

ARTIST

ALBUM

SONGS

PODCAST

GENRE

AUDIOBOOK

5-46

OTHER CONTROLS AND EQUIPMENT

AUX function

66RH077

(1) “MEDIA” button

(1)

EXAMPLE

AUX connection

To listen to auxiliary audio sources (sold

separately) through the unit, follow the

instruction below.

1) Connect the auxiliary audio source to

the AUX/USB socket (separately

attached) with an AUX cable.

2) Press “MEDIA” button (1).

Each time the button is pressed, the

mode will change as follows:

CAUTION

• Before connection, mute the unit,

and also keep the volume of the

auxiliary audio source within a

range that will not cause distortion.

• When the audio source is turned

off, noise may be emitted. Be sure

to turn off the unit or switch to

another mode before turning off the

audio source.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

5-47

OTHER CONTROLS AND EQUIPMENT

NOTE:

• Please consult your place of purchase

for details about whether a given auxil-

iary audio source can be connected and

the proper auxiliary cord to use.

• The volume and tone controls of the

auxiliary audio source can be adjusted

on the unit.

• In AUX mode, the volume setting is dif-

ferent from another mode.

5-48

OTHER CONTROLS AND EQUIPMENT

Bluetooth

hands-free (if equipped)

66RH078

(1) “TUNE/FLD PUSH SOUND” knob

(2) “VOL PUSH PWR” knob

(3) PRESET buttons

(4) BACK button

(5) Bluetooth

setup button (on control panel)

(5)

(3)

(1) (2)

(4)

EXAMPLE

Steering switch

75RM061

(6) Bluetooth

setup button (on steering

wheel)

(7) OFF HOOK button

(8) ON HOOK button

(9) MUTE switch

(10) “VOL” switch

(9)

(10)

(8)

(7)

(6)

EXAMPLE

5-49

OTHER CONTROLS AND EQUIPMENT

Phone registration

NOTE:

• Up to 5 phones can be registered.

• To set up a new phone, disconnect the

audio player from the unit. Connect the

audio player again after phone setup is

completed if necessary.

• When attempts to establish the pairing

fail within 60 seconds, the connecting

operation will be canceled. Try to estab-

lish the pairing again or refer to the man-

ual of the phone in use for how to

establish the pairing with the phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Pairing”, and press the

knob (1) to determine the selection.

4) Select “CAR AUDIO” from the Blue-

tooth

menu of the phone and establish

the pairing.

Refer to the manual of the phone in use

for further information.

5) Enter the passkey displayed on the unit

to the phone.

6) When the pairing with the phone is

established, automatic transfer of the

phonebook and the call history

becomes selectable. The automatic

transfer starts with “Yes” and it does not

with “No”.

7) Press ON HOOK button (8).

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• When registering an additional phone,

repeat Step from 1).

Receiving a call

Press OFF HOOK button (7) to receive a

call.

Ending a call

Press ON HOOK button (8) to end a call.

Rejecting a call (only for supported

models)

Press ON HOOK button (8) to reject a

incoming call.

Mute of hands-free microphone

Press MUTE switch (9) to mute the micro-

phone. To cancel the mute, press MUTE

switch (9) again.

Adjusting the listening volume

• Turn “VOL PUSH PWR” knob (2) during

a call.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press “VOL” switch (10) during a call.

Pressing the switch up increases the vol-

ume; pressing the switch down

decreases the volume.

Adjusting the ring volume

• Turn “VOL PUSH PWR” knob (2) while a

call is coming in.

Turning it clockwise increases the vol-

ume; turning it counterclockwise

decreases the volume.

• Press “VOL” switch (10) during a call.

Pressing the switch up increases the vol-

ume; pressing the switch down

decreases the volume.

To use the hands-free function with this

unit, it is required to register the phone

in advance.

5-50

OTHER CONTROLS AND EQUIPMENT

Adjusting the call or ringtone volume

Follow the instructions below to adjust the

call or ringtone volume.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Sound Setting”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Call Volume” or “Ringtone

Volume”, and press the knob (1) to

determine the selection.

The current call or ringtone volume will

be displayed.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the desired call or ringtone

volume, and press the knob (1) to

determine the selection.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Dialing using missed/incoming/

outgoing calls

Follow the instructions below to dial to the

previously dialed number again.

NOTE:

Up to 30 phone numbers of the latest calls

can be stored (30 calls including missed,

received and dialed call).

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Calls”, “Missed Calls”,

“Incoming Calls” or “Outgoing Calls”,

and press the knob (1) to determine the

selection.

To dial from the dialed history or the

received history, select “All Calls”,

“Missed Calls”, “Incoming Calls” or

“Outgoing Calls” respectively.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the desired number, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Dial”, and press the knob

(1) or OFF HOOK button (7) to dial to

the selected number.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• Pressing “Confirm” after selecting “Add

Speed Dial” can register the selected

number in the speed dial.

• Pressing “Confirm” after selecting

“Delete” can delete the selected number

from the call history.

Deletion of call history

Follow the instructions below to delete a

missed/incoming/outgoing call history.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete History”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Missed Calls”, “Incoming

Calls”, or “Outgoing Calls”, and press

the knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a number to be deleted or

“ALL”, and press the knob (1) to deter-

mine the selection.

5-51

OTHER CONTROLS AND EQUIPMENT

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?” or “Delete All?”,

and press the knob (1) to determine the

selection.

8) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Registration in Phonebook

Follow the instructions below to register

phone numbers in the Phonebook of the

unit.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Add Contacts”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Overwrite All” or “Add One

Contact”, and press the knob (1) to

determine the selection.

“Rewrite All (MAX1000): Ok?” or “Rest

of Memory XXXX: Ok?” will be dis-

played.

6) Press or turn “TUNE/FLD PUSH

SOUND” knob (1) to select “Confirm”,

and press the knob (1) to determine the

selection.

7) Transfer contacts from the phone.

When the registration is completed, the

“Setup Phonebook” will be displayed.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• Up to 1000 numbers can be registered in

Phonebook.

Transfer of call history (Call History)

Follow the instructions below to transfer

call history of the registered phone.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Call History”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Overwrite Call History?”,

and press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to transfer the call history from

the phone.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-52

OTHER CONTROLS AND EQUIPMENT

Automatic transfer of phonebook/call

history

You can select whether or not the device

transfers the phonebook and the call his-

tory automatically when the phone is regis-

tered.

Follow the instructions below to select.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “A.Transfer”, and press the

knob (1) to determine the selection.

4) Pressing “TUNE/FLD PUSH SOUND”

knob (1) switches between “

On” and “ Off”.

5) Selecting “Go Back” or pressing the

BACK button (4) stores displayed set-

ting and the previous menu is dis-

played.

Making a call by phonebook

Follow the instructions below to dial a num-

ber registered in phonebook.

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Phonebook”, and press

the knob (1) to determine the selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to make a call, and press the

knob (1) to determine the selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

make a call, and press the knob (1) to

determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Dial”, and press the knob

(1) or OFF HOOK button (7).

The displayed number or the number

registered with the displayed name will

be dialed.

Deletion of registered data (Delete

Entry)

Follow the instructions below to delete a

number registered in phonebook.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete Contacts”, and

press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to delete or “ALL”, and press

the knob (1) to determine the selection.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

delete, and press the knob (1) to deter-

mine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?” or “Delete All?”,

and press the knob (1) to determine the

selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-53

OTHER CONTROLS AND EQUIPMENT

Registration in speed dial

Follow the instructions below to assign a

number to one of PRESET buttons (3) to

use as the speed dial.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Add Speed Dial”, and

press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to register in speed dial, and

press the knob (1) to determine the

selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Choose Preset”, and

press one of PRESET buttons (3) to

which the selected number is to be

assigned. If a number is already

assigned to the selected button, a con-

firmation message will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a confirmation message,

and press the knob (1) to complete the

assignment.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the assignment.

When the assignment is completed, the

“Setup Phonebook” will be displayed.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

One-touch call (Speed dial)

Follow the instructions below to dial the

number assigned to each of the PRESET

buttons (3).

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

Pressing one of PRESET buttons (3)

can skip step 2) and the 1st line of step

3).

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Speed Dials”, and press

the knob (1) to determine the selection.

3) Press one of PRESET buttons (3).

The assigned number will be displayed.

If no number is assigned, “No Entry” is

displayed.

4) Press OFF HOOK button (7).

The selected number will be dialed.

5-54

OTHER CONTROLS AND EQUIPMENT

Deletion of speed dial (Del Speed Dial)

Follow the instructions below to delete the

number assigned for the speed dial.

1) Press OFF HOOK button (7).

The Bluetooth

phonebook menu will

be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Speed Dials”, and press

the knob (1) to determine the selection.

3) Press one of PRESET buttons (3) to

which the number to be deleted is

assigned.

If the number is not registered, “No

Entry” is displayed.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete”, and press the

knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Del Speed Dial”, and

press the knob (1) to determine the

selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Display of device data (Device Name)

Follow the instructions below to display the

BD (Bluetooth

Device) address and

device name.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Bluetooth Info”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Device Name” or “Device

Address”, and press the knob (1) to dis-

play the device name or the BD (Blue-

tooth

Device) address.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Reset to the factory defaults

Follow the instructions below to reset all

the settings to the factory defaults.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Initialize”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Initialize”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to start the reset.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-55

OTHER CONTROLS AND EQUIPMENT

Selection of phone (Select Phone)

Follow the instructions below to select a

phone to be paired with from the registered

phones.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a phone to be paired with,

and press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Select”, and press the

knob (1) to determine the selection.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• The Bluetooth

ready audio device will

be disconnected when the phone is

selected.

List of phones (List Phones)

Follow the instructions below to display the

names of the registered phones in

sequence.

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

The names of the registered phones

are displayed in sequence.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (passkey).

1) Press the Bluetooth

setup button (5)

or (6).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Passkey”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Enter New Passkey”, and

press the knob (1) to determine the

selection.

5) Press or turn “TUNE/FLD PUSH

SOUND” knob (1) to select “Confirm”.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a number for the first digit,

and press the knob (1) to determine the

selection. Select and determine num-

bers for the second, third and fourth

digits in order in the same manner.

When not entering up to the eighth

digit, enter blanks for the successive

digits.

7) Press “TUNE/FLD PUSH SOUND”

knob (1) to determine the passkey set-

ting.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-57

OTHER CONTROLS AND EQUIPMENT

Bluetooth

audio (if equipped)

66RH079

(3)

(7)

(4)

(5) (6)

(1)

(2)

EXAMPLE

Steering switch

75RM062

Display

(1) “MEDIA” button

(2) “TUNE/FLD PUSH SOUND” knob

(3) UP button

(4) DOWN button

(5) “DISP” button

(6) BACK button

(7) Bluetooth

setup button (on control

panel)

(8) Bluetooth

setup button (on steering

wheel)

(A) Track number

(B) Play time

(8)

EXAMPLE

(B)

(A)

5-58

OTHER CONTROLS AND EQUIPMENT

Registration of audio devices

NOTE:

• To set up a new audio player, disconnect

the phone from the unit. Connect the

phone after audio player setup is com-

pleted if necessary.

• When attempts to establish the pairing

fail within 60 seconds, the connecting

operation will be canceled. Try to estab-

lish the pairing again or refer to the audio

player manual for assistance with the

pairing process.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Pairing”, and press the

knob (2) to determine the selection.

4) Select “CAR AUDIO” from the Blue-

tooth

menu of the audio player and

establish the pairing.

Refer to the manual of the audio player

in use for further information.

5) Enter the passkey displayed on the unit

to the audio player.

NOTE:

• When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

• When registering additional audio

devices, repeat Step from 1).

Selecting Bluetooth

audio mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Selecting a group (only for supported

models)

Turn “TUNE/FLD PUSH SOUND” knob (2)

to select a group.

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

NOTE:

Some functions may not be available

depending on Bluetooth

audio.

Display change

Press “DISP” button (5).

Each time the button is pressed, display

will change as follows:

NOTE:

If text data contains more than 16 charac-

ters, “>” mark will appear at the right end.

Holding down “DISP” button (5) for 1 sec-

ond or longer can display the next page.

To use Bluetooth

ready audio devices

with this unit, it is required to register the

devices.

USB (iPod

) (if equipped)

Bluetooth

audio (if equipped)

AUX (if equipped)

Play time

Track name

Artist name

Album name

5-59

OTHER CONTROLS AND EQUIPMENT

Selection of audio device (Select Audio)

Follow the instructions below to select an

audio device to be paired with from the

registered audio devices.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select an audio device to be

used, and press the knob (2) to deter-

mine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Select”, and press the

knob (2) to determine the selection.

NOTE:

• When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

• The phone will be disconnected when

the Bluetooth

ready audio device is

selected.

List of audio devices (List Audio)

Follow the instructions below to display the

names of the registered audio devices in

sequence.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

The names of registered audio devices

will be displayed in sequence.

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (Passkey).

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Passkey”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Enter New Passkey”, and

press the knob (2) to determine the

selection.

5) Press or turn “TUNE/FLD PUSH

SOUND” knob (2) to select “Confirm”.

6) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select a number for the first digit,

and press the knob (2) to determine the

selection. Select and determine num-

bers for the second, third and fourth

digits in order in the same manner.

When not entering up to the eighth

digit, enter blanks for the successive

digits.

7) Press “TUNE/FLD PUSH SOUND”

knob (2) to determine the passkey set-

ting.

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

5-60

OTHER CONTROLS AND EQUIPMENT

Deletion of audio device information

(Delete Audio)

Follow the instructions below to delete the

registered audio device information.

1) Press the Bluetooth

setup button (7)

or (8).

The Bluetooth

setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select an audio device to be

deleted, and press the knob (2) to

determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Delete”, and press the

knob (2) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Delete?”, and press the

knob (2) to determine the selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Confirm”, and press the

knob (2) to complete the deletion.

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

Disclaimer for Bluetooth

function

• Depending on compatibility of mobile

phone models, no Bluetooth

function

can be used, or some Bluetooth

func-

tions may be restricted.

• Connectivity or voice quality may get

affected depending on circumstances.

• After the ignition switch is turned to “ON”

position or the engine switch is pressed

to change the ignition mode to ON, the

audio system takes few seconds to

detect and connect to the Bluetooth

device (if already paired).

Remote audio controls (if equipped)

Controlling basic functions of the audio

system is available using the switches on

the steering wheel.

75RM063

(4)

(2)

(1) (3)

EXAMPLE

5-61

OTHER CONTROLS AND EQUIPMENT

Adjusting the volume

• To increase the volume, press the “VOL”

switch (1) up. The volume will continue

to increase until the switch is released.

• To decrease the volume, press the

“VOL” switch (1) down. The volume will

continue to decrease until the switch is

released.

• To mute the sound, press the switch (2).

Selecting the mode

Press the switch (3).

Each time the button is pressed, the mode

will change as follows:

It is possible to turn on the audio system

by pressing the switch (3).

Selecting the radio station (AM, FM1,

FM2 mode)

• To select the next preset station, press

“>” of the switch (4) only for a moment.

• To select the previous preset station,

press “<” of the switch (4) only for a

moment.

• To scan a higher frequency radio station,

press “>” of the switch (4) for 1 second

or longer.

• To scan a lower frequency radio station,

press “<” of the switch (4) for 1 second

or longer.

Selecting the track (CD, USB (iPod

Bluetooth

audio mode)

• To skip to the next track, press “>” of the

switch (4) only for a moment.

• To skip to the previous track, press “<” of

the switch (4) twice only for a moment.

When the switch (4) is pushed down

once only for a moment, the track cur-

rently being played will start from the

beginning again.

Fast forwarding/rewinding a track

• To fast forward a track, press “>” of the

switch (4) for 1 second or longer.

• To fast rewind a track, press “<” of the

switch (4) for 1 second or longer.

FM1 (Radio)

FM2 (Radio)

Bluetooth

audio (if equipped)

AUX (if equipped)

USB (iPod

) (if equipped)

AM (Radio)

5-62

OTHER CONTROLS AND EQUIPMENT

Anti-theft feature

66RH080

(1) VOL PUSH PWR” knob

(2) PRESET buttons ([1] to [6])

(3) UP button

(4) “TUNE/FLD PUSH SOUND” knob

(3)

(4) (1)

(2)

EXAMPLE

The anti-theft function is intended to dis-

courage thefts. For example, when the

audio system is installed in another vehi-

cle, it will become unable to operate.

This function works by entering a Personal

Identification Number (PIN).

When the unit is disconnected from its

power source, such as when the audio

system is removed or the battery is discon-

nected, the unit will become inoperable

until the PIN is reentered.

5-63

OTHER CONTROLS AND EQUIPMENT

Setting the anti-theft function

1) Press “VOL PUSH PWR” knob (1) to

power off.

2) Hold down the buttons numbered [1]

and [6] of PRESET buttons (2) and

press “VOL PUSH PWR” knob (1).

“SECURITY” will be displayed.

3) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

5) Hold down “TUNE/FLD PUSH

SOUND” knob (4) for 1 second or lon-

ger to set the anti-theft function.

NOTE:

Take a note of the registered PIN and keep

it for the future use.

Canceling the anti-theft feature

To cancel the anti-theft function, delete the

registered PIN.

1) Press “VOL PUSH PWR” knob (1) to

power off.

2) Hold down the buttons numbered [1]

and [6] of PRESET buttons (2) and

press “VOL PUSH PWR” knob (1).

“PIN ENTRY” will be displayed.

3) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

5) Hold down “TUNE/FLD PUSH

SOUND” knob (4) for 1 second or lon-

ger to delete the registered PIN. The

indication “----” will be displayed and

the anti-theft function will be canceled.

NOTE:

To change your PIN, first delete your cur-

rent PIN, and then set a new one.

Confirming the Personal Identification

Number (PIN)

When the main power source is discon-

nected such as when the battery is

replaced, etc, it is required to enter the PIN

to operate the unit again.

1) Set the ignition switch to “ACC” posi-

tion or the ignition mode to ON.

“SECURITY” will be displayed.

2) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

3) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

4) Hold down “TUNE/FLD PUSH

SOUND” knob (4) for 1 second or lon-

ger.

When the same PIN as registered is

entered, the power of the audio system

will be turned off automatically and it

will become operable again.

NOTE:

If an incorrect PIN is entered, “ERROR”

and the total number of incorrect entry

attempts will be displayed.

If an incorrect PIN is entered 10 times or

more, “HELP” will be displayed and the

audio system will become inoperable.

5-64

OTHER CONTROLS AND EQUIPMENT

Battery installation

Install a lithium battery (CR2025) with the poles facing the correct direction.

Battery replacement timing

• When battery power is depleted, the button may not be operable. If the remote controller

does not operate, replace the battery and check the operation.

Caution on battery

• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or

explosion.

EXAMPLE

If battery leakage has occurred, wipe the

container first then install a new battery. If

the battery solution contacts the skin, wash

off with water completely.

WARNING

• Do not expose the battery to flame.

Do not short circuit, disassemble,

or heat the battery.

• Do not charge the battery.

• Use the specified type battery.

• Keep the button-shaped battery

away from children to prevent acci-

dental swallowing.

If the battery is swallowed, contact a

doctor immediately.

CAUTION

• Install the battery with the poles

facing the correct direction.

• When not in use for a long period

of time, or if the battery is dead,

remove the battery from the remote

controller.

5-65

OTHER CONTROLS AND EQUIPMENT

Caution on remote controller

• Do not leave the remote controller in an

area exposed to direct sunlight, such as

on the dashboard or steering wheel. The

remote controller may deform because

of the heat, (Be especially careful of the

dashboard exposed to direct sunlight in

the summer, as it will become extremely

hot).

• When the vehicle is parked in an area

exposed to direct sunlight, Ensure the

remote controller is placed in an area not

exposed to direct sunlight. For example:

Glove box.

Under direct sunlight, signal reception

from the remote controller weakens. If

this happens, hold the remote controller

close to the signal receptor on the front

panel.

5-66

OTHER CONTROLS AND EQUIPMENT

Remote controller (if equipped)

Common operations

In Sound Mode

Press to adjust the sound (bass/treble/balance/fader).

In Preset-EQ Mode

The Preset-EQ setting switches as follows:

In AVC Mode

The AVC setting switches

as follows:

TUNE FOLDER UP/DOWN button

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

OFF

LEVEL 1

LEVEL 2

LEVEL 3

TUNE

VOL -

VOL +

FLD

TUNE

MODE

SOUND

FLD

ENT

SEEK

TRACK

SEEK

TRACK

RPT RDM

DISP

Power ON / OFF

POWER button

Press to adjust volume.

(including at AUX mode)

VOLUME button

Press to mute the sound. Press it again to cancel

the mute.

MUTE button

While playback, the sound mode switches as

follows (including at AUX mode, except while

displaying iPod

menu):

SOUND button

Preset-EQ

BASS

TREBLE

BALANCE

FADER

AVC

The mode switches as

follows:

MODE button

FM1

FM2

Bluetooth

audio

(if equipped)

AUX (if equipped)

USB (iPod

)

(if equipped)

5-67

OTHER CONTROLS AND EQUIPMENT

Radio operations

TUNE

VOL -

VOL +

FLD

TUNE

MODE

SOUND

FLD

ENT

SEEK

TRACK

SEEK

TRACK

RPT RDM

DISP

NOTE:

When there are fewer than 6 stations that can be stored even if 1 round of auto store operation is performed, no station will be

stored at the remaining preset buttons.

Press to return to the last received fre-

quency in the previous auto store mode.

Press it for 2 seconds or longer. It selects

the stations with the stronger signals and

stores them in order.

AS button

Press to select the radio station.

SEEK TRACK UP/DOWN button

Press to select the desired preset station.

PRESET buttons (1-6)

5-68

OTHER CONTROLS AND EQUIPMENT

CD operations

TUNE

VOL -

VOL +

FLD

TUNE

MODE

SOUND

FLD

ENT

SEEK

TRACK

SEEK

TRACK

RPT RDM

DISP

Press to play the current track randomly.

Press it again to cancel.

RDM (5) button

Press to plays the current track repeatedly.

Press it again to cancel.

RPT (4) button

Press to skip to the next/previous track.

Press it for 1 second or longer to fast-forward/

fast-rewind the track.

SEEK TRACK UP/DOWN button

The display switches as follows:

Press it for 1 second or longer to display the

next page.

DISP (6) button

Play time

Disc title

Track title

5-69

OTHER CONTROLS AND EQUIPMENT

MP3/WMA/AAC Disc operations

TUNE

VOL -

VOL +

FLD

TUNE

MODE

SOUND

FLD

ENT

SEEK

TRACK

SEEK

TRACK

RPT RDM

DISP

The random mode switches as follows:

RDM (5) button

OFF

FOLDER RANDOM

ALL RANDOM

The repeat mode switches as follows:

RPT (4) button

OFF

FILE REPEAT

FOLDER REPEAT

Press to skip to the next/previous folder.

TUNE FOLDER UP/DOWN button

The display switches as follows:

Press it for 1 second or longer to display the next

page.

DISP (6) button

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

Artist name

Press to skip to the next/previous track.

Press it for 1 second or longer to fast-forward/fast-

rewind the track.

SEEK TRACK UP/DOWN button

5-70

OTHER CONTROLS AND EQUIPMENT

USB operations

TUNE

VOL -

VOL +

FLD

TUNE

MODE

SOUND

FLD

ENT

SEEK

TRACK

SEEK

TRACK

RPT RDM

DISP

Press to skip to the next/previous file.

Press it for 1 second or longer to fast-forward/fast-

rewind the file.

SEEK TRACK UP/DOWN button

The repeat mode switches as follows:

RPT (4) button

OFF

FILE REPEAT

FOLDER REPEAT

The display switches as follows:

Press it for 1 second or longer to display the next

page.

DISP (6) button

Play time

Folder name

File name

Album name

(MP3, AAC only)

Track title

Artist name

Press to skip to the next/previous folder.

TUNE FOLDER UP/DOWN button

The random mode switches as follows:

RDM (5) button

OFF

FOLDER RANDOM

ALL RANDOM

5-71

OTHER CONTROLS AND EQUIPMENT

iPod

operations

TUNE

VOL -

VOL +

FLD

TUNE

MODE

SOUND

FLD

ENT

SEEK

TRACK

SEEK

TRACK

RPT RDM

DISP

While displaying iPod

menu, press to select the

desired item and display the list. When a track is

selected from the list, the playback starts.

ENT button

The random mode switches as follows:

RDM (5) button

OFF

SONG RANDOM

ALBUM RANDOM

Press to play the current track repeatedly.

Press it again to cancel.

RPT (4) button

The display switches as follows:

Press it for 1 second or longer to display the next

page.

DISP (6) button

Playlist name /

Track title (Playlist mode only)

Artist name / Track title

Album name / Track title

Track title / Play time

During playback

• Press to display iPod

menu.

• Press it for 1 second or longer to display the top menu.

While iPod

menu is displayed

• Press to display the folder in one layer upper.

• Press it for 1 second or longer to display the top menu.

MENU button

While displaying iPod

menu, press to dis-

play the next/previous list in the same layer.

TUNE FOLDER UP/DOWN button

Press to skip to the next/previous file.

Press it for 1 second or longer to fast-forward/fast-

rewind the file.

SEEK TRACK UP/DOWN button

5-72

OTHER CONTROLS AND EQUIPMENT

Troubleshooting

When encountering a problem, check and follow the instructions below.

If the described suggestions do not solve the problem, it is recommended to take the unit to your authorised Maruti Suzuki workshop.

Problem Possible cause Possible solution

Common

Unable to operate The security function is on.

When “SECURITY” is displayed, enter

the PIN.

When “HELP” is displayed, contact your

authorised Maruti Suzuki workshop.

Unable to turn on the power

(No sound is produced)

Fuse is blown.

Contact your authorised Maruti Suzuki

workshop.

Radio

High noise

It may not be exactly tuned in to the sta-

tion.

Tune it in exactly to the station.

Unable to receive by auto tuning

There may be no station emitting signals

powerful enough.

Pick up a station by manual tuning.

Sound skips or noise produced

The disc is dirty. Wipe the disc with a soft cloth.

The disc has a major scratch or is

warped.

Replace the disc with the one which has

no scratch and warp.

5-73

OTHER CONTROLS AND EQUIPMENT

MP3/WMA/AAC

No playback

The disc contains unsupported formatted

data.

Check the file format.

Sound skips or noise produced

Sound skipping may occur when playing

VBR (Variable Bit Rate) files.

It is not recommended to play VBR files.

USB

Playback does not start when the USB

device is connected

There is no supported format file to play

on this unit.

Check the file format.

The current consumption of the USB

device exceeds 1.0 A.

Use a USB device with a current con-

sumption lower than 1.0 A.

Bluetooth

Pairing failed

The distance between this unit and the

Bluetooth

ready device is too far, or a

metallic object may be located between

the Bluetooth

ready device and this unit.

Change the location of the Bluetooth

ready device.

The Bluetooth

function of the Bluetooth

ready device is off.

Refer to the manual of the Bluetooth

ready device (Some devices have the

power saving function that automatically

activates after a certain time).

Unable to receive a call

Your current location may be out of ser-

vice area.

Drive your vehicle to the service area of

the phone.

The voice quality of hands-free is low

(Distortion, noise etc.)

Another wireless device may be located

near the unit.

Switch off the wireless device or keep it

away from the unit.

Problem Possible cause Possible solution

5-74

OTHER CONTROLS AND EQUIPMENT

Error display messages

Display Possible cause Possible solution

“ERROR 1” The disc cannot be read.

Insert the disc with its label side up.

Check the disc if it is not warped or is free of flaws.

When “ERROR 1” does not disappear even when a nor-

mal disc is inserted, contact your dealer.

“ERROR 3”

The player developed an error of an

unidentified cause.

When the CD is in the unit, press the CD eject button to

remove the disc.

When the disc cannot be ejected, contact your dealer.

USB/iPod

“USB ERROR” The USB device is disconnected. Check the connection of the USB device.

“ERROR 2”

Impossible to communicate correctly with

the USB device.

Unplug the USB device and plug it again.

Check the USB device.

“ERROR 3” Inoperable due to an unidentified cause.

Unplug the USB device and plug it again.

When “ERROR 3” does not disappear, contact your

dealer.

“ERROR 4”

The current consumption of the USB

device exceeds 1.0 A.

Check the USB device.

5-75

OTHER CONTROLS AND EQUIPMENT

Bluetooth

“ERROR 1”

The player developed an error of an

unidentified cause.

Disconnect the Bluetooth

ready device and connect it

again.

When “ERROR 1” does not disappear, contact your

dealer.

“Connection Failed” Failed to establish pairing or connection. Try to establish the pairing or connection again.

“Memory Full”

Reached the limit for the number of phone-

book data in transfer.

Delete registered data of unnecessary number in phone-

book and try to transfer the register phone numbers in

the phonebook again.

“Not Available” Inoperable during driving. Operate the system after pulling over your car.

Display Possible cause Possible solution

Other Controls and Equipment for Your Suzuki Ignis SUV First Generation (2000-2008)

Related Topics

Popular Owner Manuals

Latest Owner Manuals