2016-2024 Suzuki Ignis SUV Inspection and Maintenance -> Bulb replacement User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Inspection and Maintenance -> Bulb replacement for Your Suzuki Ignis SUV Second Generation (2016-2024)

7-49
INSPECTION AND MAINTENANCE
75RM4-01E
Bulb replacement
Interior light
Remove the lens by using a flat-bladed
screwdriver covered with a soft cloth as
shown. To install it, simply push it back in.
Front
76MH0A139
Luggage compartment (if equipped)
81PN162
Headlights
LED headlights (if equipped)
Since special procedures are required, we
recommend you take your vehicle to your
SUZUKI dealer for bulb replacement.
Halogen headlights (if equipped)
75RM067
1) Open the engine hood. Disconnect the
coupler (1). Remove the sealing rubber
(2).
CAUTION
• Light bulbs can be hot enough to
burn your finger right after turning
off lights. This is true especially for
halogen headlight bulbs. Replace
the bulbs after they become cool
enough.
• The halogen headlight bulbs are
filled with pressurized halogen gas.
They can burst and injure you if
they are hit or dropped. Handle
them carefully.
• To avoid injury by sharp-edged
parts of the body, wear gloves and
a long-sleeved shirt when replacing
light bulbs.
NOTICE
The oils from your skin may cause a
halogen bulb to overheat and burst
when the lights are on. Grasp a new
bulb with a clean cloth.
NOTICE
Frequent bulb replacement indicates
the need for an inspection of the elec-
trical system. This should be carried
out by your SUZUKI dealer.
(1)
(2)
7-50
INSPECTION AND MAINTENANCE
75RM4-01E
75RM068
2) Push the retaining spring (3) forward
and unhook it. Then remove the bulb.
Install a new bulb in the reverse order
of removal.
75RM069
NOTE:
You can see the position of retaining spring
from the hole (4) of headlight.
Side turn signal light (if equipped)
64J195
Since the bulb is built-in type, replace it as
the light assembly. Remove the light
assembly by sliding the light housing left-
ward with your finger.
(3)
(4)
7-51
INSPECTION AND MAINTENANCE
75RM4-01E
Front fog light (if equipped)
1) Start the engine. Turn the steering
wheel to the opposite side of the fog
light to be replaced to replace the bulb
easily. Then turn off the engine.
75RM094
2) Remove the clip (1) by prying it off with
a flat-bladed screwdriver as shown in
the illustration.
80JM071
3) Open the end of the cover inside the
fender. Disconnect the coupler by push-
ing the lock release. Turn the bulb
holder counterclockwise and remove it.
Daytime running light (if equipped)
Models with LED headlights
Since special procedures are required, we
recommend you take your vehicle to your
SUZUKI dealer for bulb replacement.
Models with halogen headlights
1) Start the engine. Turn the steering
wheel to the opposite side of the fog
light to be replaced the bulb easily.
Then turn off the engine.
75RM094
2) Remove the clip (1) by prying it off with
a flat-bladed screwdriver as shown in
the illustration.
(1)
EXAMPLE
(1)
7-52
INSPECTION AND MAINTENANCE
75RM4-01E
75RM244
3) Open the end of the cover inside the
fender. Disconnect the coupler by push-
ing the lock release. Turn the bulb
holder counterclockwise and remove it.
Other general lights
Bulb holder
54G123
(1) Removal
(2) Installation
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and
pull it out. To install the holder, push the
holder in and turn it clockwise.
Bulb
54G124
(3) Removal
(4) Installation
There are two types of bulb, full glass type
(1) and glass/metal type (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.
EXAMPLE
(1)
(1)
(2)
(2)
EXAMPLE
(1)
(2)
(3)
(4)
EXAMPLE
7-53
INSPECTION AND MAINTENANCE
75RM4-01E
Front turn signal light (1)
Front position light (2)
Models with halogen headlights
75RM066
Models with LED headlights
62R0306
Rear combination light
75RM070
Remove the bolts (1) and pull the light
housing (2) straight.
NOTE:
When reinstalling the light housing, check
that the clips (3) are properly attached.
Reversing light
62R0122
1) Open the tailgate and remove the trim
(1) of the tailgate.
• Insert a flat blade screwdriver cov-
ered with a soft cloth between the trim
and the tailgate to make a space for
fingers, and then pull out the trim with
your fingers.
(1)
(2)
(1)
(3)
(2)
(1)
(1)
7-54
INSPECTION AND MAINTENANCE
75RM4-01E
62R0378
2) Disconnect the coupler (2) by pushing
the lock release. Turn the bulb holder of
the reversing light (3) counterclockwise
and remove it.
License plate light
75RM071
Rear fog light (if equipped)
75RM072
1) Remove the clip (1) by prying it off with
a flat blade screwdriver as shown in the
illustration.
75RM073
2) Open the end of the cover inside the
fender.
(2)
(3)
(1)

Related Topics

Inspection and Maintenance
Maintenance schedule Periodic maintenance schedule (except for EU countries and Israel) Maintenance recommended under severe driving conditions (except for EU countries and Israel) Periodic maintenance schedule (for EU countries and Israel) Maintenance recommended under severe driving conditions (for EU countries and Israel) Drive belt Engine oil and filter Engine coolant Air cleaner Spark plugs Continuously variable transaxle (CVT) fluid Gear oil Clutch pedal Brakes Steering Tires Battery Fuses Headlight aiming Wiper blades Windshield washer fluid Air conditioning system

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot