Get Inspection and Maintenance -> Bulb Replacement Guide for Suzuki S Cross SUV First Generation (2006-2012)

7-40

INSPECTION AND MAINTENANCE

80J23-03E

Bulb Replacement

NOTE:

If it is difficult to replace headlight bulbs or

position light bulbs due to under-hood

components trust this job to your dealer.

Center Interior Light (if equipped)

60G115

Pull down the lens by using a flat blade

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

The bulb can be removed by simply pulling

it out. When replacing the bulb, make sure

that the contact springs are holding the

bulb securely.

Spot light

80JM068

Pull down the lens by using a flat blade

screwdriver covered with a soft cloth as

shown. To install it, simply push it back in.

WARNING

• Light bulbs can be hot enough to

burn your finger right after being

turned off. This is true especially

for halogen headlight bulbs.

Replace the bulbs after they

become cool enough.

• The headlight bulbs are filled with

pressurized halogen gas. They can

burst and injure you if they are hit

or dropped. Handle them carefully.

CAUTION

The oils from your skin may cause a

halogen bulb to overheat and burst

when the lights are on. Grasp a new

bulb with a clean cloth.

CAUTION

Frequent replacement of a bulb indi-

cates the need for an inspection of

the electrical system. This should be

carried out by your SUZUKI dealer.

7-41

INSPECTION AND MAINTENANCE

80J23-03E

Headlights

80J2084

Open the engine food. Disconnect the cou-

pler (1). Then remove the socket cover (2)

and replace the bulb. Install a new bulb in

the reverse order of removal.

Other General Lights

Bulb holder

54G123

(1) Removal

(2) Installation

To remove a bulb holder from a light hous-

ing, turn the holder counterclockwise and

pull it out. To install the holder, push the

holder in and turn it clockwise.

Bulb

54G124

(3) Removal

(4) Installation

There are two types of bulb, “Full glass

type” (1) and “Glass/metal type” (2).

To remove and install a full glass type bulb

(1), simply pull out or push in the bulb.

To remove a glass metal type bulb (2) from

a bulb holder, push in the bulb and turn it

counterclockwise. To install a new bulb,

push it in and turn it clockwise.

You can access the individual bulb or bulb

holders as follows.

(1)

(2)

(1)

(2)

EXAMPLE

(1)

(2)

(3)

(4)

EXAMPLE

7-42

INSPECTION AND MAINTENANCE

80J23-03E

Front turn signal light (1)

Front position light (2)

80JM123

Front fog light (if equipped)

1) Start the engine. Turn the steering

wheel to the opposite side of the replac-

ing fog light to replace the bulb easily.

Then turn off the engine.

80JM114

2) Insert a flat blade screwdriver into the

hole (2) and remove the clips (1) by

twist the driver as shown in the illustra-

tion.

80JM115

3) Remove the bolts (3).

(1) (2)

(1)

(2)

EXAMPLE

(

)

EXAMPLE

7-43

INSPECTION AND MAINTENANCE

80J23-03E

SX4

80JM116

4) Open the fender cover. Disconnect the

coupler by pushing the lock release.

Pinch both side of the clips (4) and (5),

and push them in.

80JM117

5) Remove the front fog light. Turn the

bulb holder counterclockwise and

remove it.

SX4 SEDAN

80JM071

4) Open the fender cover. Disconnect the

coupler with pushing the lock release.

Turn the bulb holder counterclockwise

and remove it.

Rear combination light

(tail, stop, turn signal, etc.)

SX4

80JM131

SX4 SEDAN

80JM072

(4)

(5)

EXAMPLE

(2)

(1)

7-44

INSPECTION AND MAINTENANCE

80J23-03E

To open the trim (1), insert a flat blade

screwdriver between the trim and the clips

(2) and remove the clips by twist the driver

as shown in the illustration.

80JM073

License plate light

SX4

80JM079

SX4 SEDAN

80JM074

To open the trim (1), insert a flat blade

screwdriver into the hole (3) and remove

the clips (2) by twist the driver as shown in

the illustration.

80JM075

(3)

(1)

(2)

7-45

INSPECTION AND MAINTENANCE

80J23-03E

Luggage compartment light (SX4)

79J015

Trunk room light (SX4 SEDAN)

56KN004

High-mount stop light (if equipped)

SX4

80J100

To remove a high-mounted stop light hous-

ing the following procedure:

1) Open the tailgate, and remove the nuts

(1) as shown in the illustration.

63J127

2) Close the tailgate. Remove a high-

mounted stop light housing (2) from the

tailgate.

(1)

(2)

7-46

INSPECTION AND MAINTENANCE

80J23-03E

80JM076

3) Pushing the unguiform prongs (3)

toward inside and remove the bulb

holder (4).

4) Replace the bulbs.

To install a high-mounted stop light

housing in the reverse order of removal.

SX4 SEDAN

80JM132

To remove the high-mounted stop light

housing, pinch both side of the clip (1) and

push it in.

Wiper Blades

80G083

If the wiper blades become brittle or dam-

aged, or make streaks when wiping,

replace the wiper blades.

To install new wiper blades, follow the pro-

cedures below.

NOTE:

Some wiper blades may be different from

the ones described here depending on

vehicle specifications. If so, consult your

SUZUKI dealer for proper replacement

method.

(3)(3) (4)

(1)

CAUTION

To avoid scratching or breaking the

window, do not let the wiper arm

strike the window while replacing the

wiper blade.

Inspection and Maintenance -> Bulb Replacement for Your Suzuki S Cross SUV First Generation (2006-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals