Get OTHER CONTROLS AND EQUIPMENT -> Audio system (Type A / Type B) (if equipped) Guide for Suzuki Swift 4 Door First generation (2004-2009)

OTHER CONTROLS AND EQUIPMENT

Audio system (Type A / Type B) (if equipped)

EXAMPLE

Type A

Type B

52RM50500

®

Type A: AM/FM/DAB CD player with Bluetooth function

®

Type B: AM/FM CD player with Bluetooth function

5-33

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Cautions on handling

Safety information

WARNING

Notes on discs

Precautions

•

When the inside of the vehicle is very

cold and the player is used soon after

switching on the heater, condensation

may form on the compact disc (CD) or

the optical parts of the player and

proper playback may not be possible. If

condensation forms on the disc, wipe it

off with a soft cloth. If condensation

forms on the optical parts of the player,

do not use the player for about one

hour. This will allow the condensation

to disappear normally.

If you pay too much attention to

operating the audio system or

watching the audio system display

while driving, an accident can

occur. If you set the sound volume

too loud, it could prevent you from

being aware of road and traffic con-

ditions.

• Keep your eyes on the road and

your mind on the drive. Avoid pay-

ing too much attention to operat-

ing the audio system or watching

the audio system display.

(A)

52D274

This unit has been designed specifically for

playback of compact discs bearing mark

(A) shown above.

No other discs can be played.

•

Driving on extremely bumpy roads

which cause severe vibrations may

cause sound to skip when playing a

CD.

This unit uses a precision mechanism.

Even in the event that trouble arises,

never open the case, disassemble the

unit, or lubricate the rotating parts.

Bring the unit to an authorized SUZUKI

dealer.

• Familiarize yourself with the audio

system controls and operation of

the audio system before driving.

• Preset your favorite radio stations

before driving so that you can

quickly tune to them using the

presets.

• Set the sound volume to a level

that will allow you to continue to

be aware of surrounding road and

traffic conditions while driving.

5-34

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Removing the disc Proper way to hold

the compact disc

52D347

52D348

To remove fingermarks or dust, use a soft

cloth, and wipe in a straight line from the

center of the compact disc to the edge.

Never affix labels on the surface of the

compact disc or write on the surface with a

pencil or pen.

52D275

To remove the compact disc from its stor-

age case, press down on the center of the

case and lift the disc out, holding it care-

fully by the edges.

(B)

(C)

Always handle the compact disc by the

edges.

Never touch the surface.

52D349

Do not use any solvents such as commer-

cially available cleaners, anti-static spray,

or thinner to clean compact discs.

52D277

New discs may have some roughness

around the edges. The unit may not work

or the sound may skip if such discs are

used. Use a ball-point pen (B), etc. to

remove the roughness (C) from edges of

the disc before inserting it into the unit.

5-35

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

52D350

52D351

Do not use compact discs that have large

scratches, are misshaped, or cracked, etc.

Use of such discs will cause damage or

prevent the system from operating prop-

erly.

Do not expose compact discs to direct sun-

light or any heat source.

NOTE:

• Do not use commercially available CD

protection sheets or discs equipped with

stabilizers, etc.

These may get caught in the internal

mechanism and damage the disc and the

mechanism.

• It may be impossible to play CD-R discs

with this unit due to the recording format.

• CD-RW discs cannot be played with this

unit.

5-36

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

WARNING

®

The Bluetooth word mark and logo are

Access to http://www.ptc.panasonic.eu/,

enter the below

Model No. into the keyword search box,

you can download the latest “DECLARA-

TION of CONFORMITY” (DoC).

This is a class I laser product. Use

of controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by your-

self.

registered trademarks and are owned by

the Bluetooth SIG, Ink.

®

Stop using this unit and a Bluetooth

ready device whenever requested.

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

Set No. AZ1601

Ask an authorized SUZUKI dealer

for the repair.

You should stop using this unit immediately

whenever you are notified that your unit

disturbs other wireless communication.

5-37

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Information on disposal for users of waste electrical & electronic equip-

ment (private households)

This symbol on the products and/or accompanying documents

means that used electrical and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and recycling, please take these

products to designated collection points, where they will be accepted

on a free of charge basis. Alternatively, in some countries you may

be able to return your products to your local retailer upon the pur-

chase of an equivalent new product.

Disposing of this product correctly will help to save valuable

resources and prevent any potential negative effects on human

health and the environment which could otherwise arise from inap-

propriate waste handling. Please contact your local authority for fur-

ther details of your nearest designated collection point.

68LM560

Penalties may be applicable for incorrect disposal of this waste, in

accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

Information on disposal in other countries outside the European Union

This symbol is only valid in the European Union.

If you wish to discard this product, please contact your local authorities or dealer and ask

for the correct method of disposal.

Declaration of Conformity (Doc)

“Hereby Panasonic Corporation, declares

that this Set No. AZ1601 is in compliance

with the essential requirements and other

relevant provision of Directive 1999/5/EC”

5-38

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Part 15 of the FCC Rules

WARNING

FCC ID: ACJ932AZ1601

®

The Bluetooth word mark and logo are

This is a class I laser product. Use of

controls or adjustments or perfor-

mance of procedures other than

those specified herein may result in

hazardous radiation exposure.

Do not open covers and do not

attempt to repair this unit by yourself.

Ask an authorized dealer for the

repair.

registered trademarks and are owned by

the Bluetooth SIG, Ink.

NOTE:

Properly shielded and grounded cables

and connectors must be used for connec-

tion to host computers and/or peripherals

in order to meet FCC emission limits.

NOTE:

This equipment complies with FCC radia-

tion exposure limits set forth for uncon-

trolled equipment and meets the FCC

radio frequency (RF) Exposure Guidelines

in Supplement C to OET65. This equip-

ment has very low level of RF energy

which does not comply with maximum per-

missive exposure (MPE) evaluation. But it

is desirable that it should be installed and

operated with at least 20cm and more

between the radiator and person’s body

(excluding extremities: hands, wrists, feet

and ankles).

WARNING

RF Exposure

This equipment complies with FCC

radiation exposure limits set forth for

an uncontrolled environment and

meets the FCC radio frequency (RF)

Exposure Guidelines. This equipment

has very low levels of RF energy that

it deemed to comply without maxi-

mum permissive exposure evaluation

(MPE). [But it is desirable that it

should be installed and operated

keeping the radiator at least 20 cm or

more away from person’s body.]

CAUTION

Changes

or

modifications

not

expressly approved by the party

responsible for compliance could

void the user’s authority to operate

the equipment.

5-39

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

®

Stop using this unit and a Bluetooth

ready device whenever requested.

NOTE:

These limits are designed to provide rea-

sonable protection against harmful interfer-

ence in a residential installation. This

equipment generates, uses and can radi-

ate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interfer-

ence to radio communications. However,

there is no guarantee that interference will

not occur in a particular installation. If this

equipment does cause harmful interfer-

ence to radio or television reception, which

can be determined by turning the equip-

ment off and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

This unit shares the communication fre-

quency with other private or public wireless

communication equipment such as a wire-

less LAN and other wireless communica-

tion radios.

You should stop using this unit whenever

you are notified that your unit disturbs

other wireless communication immediately.

• Reorient or relocate the receiving anten-

na.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

• This transmitter must not be co-located

or operated in conjunction with any other

antenna or transmitter.

5-40

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Basic operations

Turning on/off power

Press “VOL PUSH PWR” knob (1) to turn

on the audio system. The unit starts to

operate in the previous setting that the

system was turned off.

EXAMPLE

Type A

Adjusting the volume

Turn “VOL PUSH PWR” knob (1).

Turning it clockwise increases the volume;

turning it counterclockwise decreases the

volume.

NOTE:

(1)

(2)

For the purposes of safe driving, adjust the

audio volume to a level that allows you to

hear sounds outside of the vehicle includ-

ing car horns and particularly emergency

vehicle sirens.

Type B

(1)

(2)

52RM50510

(1) “VOL PUSH PWR” knob

(2) “TUNE/FLD PUSH SOUND” knob

5-41

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Adjusting bass/treble/balance/fader

1) Press “TUNE/FLD PUSH SOUND”

knob (2).

Adjusting the AVC (Auto volume con-

trol)

Preset-EQ

Preset-EQ (equalizer) calls up various

sound modes optimized for specific music

The Auto Volume Control (AVC) function

Each time the knob is pressed, sound

adjustment mode will change as fol-

lows:

automatically

adjusts

(increases/

category.

decreases) the sound volume in accor-

dance with vehicle speed. The AVC control

is provided with three selectable levels

(LEVEL OFF, 1, 2, 3). The range of volume

adjustment increases together with the

LEVEL number.

1) Press “TUNE/FLD PUSH SOUND”

knob (2) several times until “PRESET-

EQ” appears.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2).

Preset-EQ (EQ OFF)

Each time the knob is turned, preset

EQ mode will change as follows:

1) Press “TUNE/FLD PUSH SOUND”

knob (2) until the AVC adjustment mode

is selected.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select the desired AVC adjust-

ment level. (Initial setting: LEVEL 2)

Bass adjustment (BASS 0)

Treble adjustment (TREBLE 0)

Balance adjustment (BALANCE 0)

Fader adjustment (FADER 0)

AVC adjustment (AVC LEVEL 2)

OFF (FLAT)

JAZZ

ROCK

POP

CLASSIC

HIP-HOP

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to adjust the sound.

5-42

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Listening to the radio (Type A)

Display

(A)

EXAMPLE

(B)

68LM561

(A) Band

(B) Frequency

(1)

(2)

(3)

(6)

(4)

(5)

52RM50520

(1) “RADIO” button

(2) UP button

(3) DOWN button

(4) “TUNE/FLD PUSH SOUND” knob

(6) “AS” button

(5) PRESET buttons ([1] to [6])

5-43

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Selecting the reception band

Press the “RADIO” button (1).

Each time the button is pressed, the recep-

tion band will change as follows:

Preset memory

Auto store mode on/off

Press “AS” button (6).

Each time the button is pressed, the mode

is switched as follows:

1) Select the desired station.

2) Hold down a desired button ([1] to [6])

of PRESET buttons (5) to which you

want to store the station for 2 seconds

or longer.

FM1 FM2 DAB1 (if equipped)

AM DAB2 (if equipped)

AS mode on AS mode off

Auto store

Hold down “AS” button (6) for 2 seconds or

longer.

6 stations in good reception will automati-

cally be stored to PRESET buttons (5) in

order, starting from a station whose fre-

quency is the lowest.

Seek tuning

Radio reception

Press UP button (2) or DOWN button (3).

The unit stops searching for a station at a

frequency where a broadcast station is

available.

Radio reception can be affected by envi-

ronment, atmospheric conditions, or radio

signal’s power and distance from the sta-

tion. Nearby mountains and buildings may

interfere or deflect radio reception, causing

poor reception. Poor reception or radio

static can also be caused by electric cur-

rent from overhead wires or high voltage

power lines.

NOTE:

• Auto store can be released by pressing

“AS” button (6) while auto store is under

way.

• When the auto store is performed, the

station previously stored in the memory

at the position is overwritten.

NOTE:

If AF is on, the unit searches for RDS sta-

tions only.

Manual tuning

• When there are fewer than 6 stations that

can be stored even if 1 round of auto

store operation is performed, no station

will be stored at the remaining PRESET

buttons (5).

Turn “TUNE/FLD PUSH SOUND” knob (4).

The frequency being received is displayed.

• 6 stations can be preset for FM1 and

FM2 in common, and 6 stations for AM in

auto store mode.

• If AF is on, the unit searches for RDS

stations only.

5-44

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Listening to the radio (Type B)

Display

(A)

EXAMPLE

(B)

(A) Band

(B) Frequency

(1)

(2)

(3)

(4)

(7)

(5)

(6)

52RM50530

(1) “FM” button

(2) “AM” button

(3) UP button

(4) DOWN button

(5) “TUNE/FLD PUSH SOUND” knob

(7) “AS” button

(6) PRESET buttons ([1] to [6])

5-45

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Selecting the FM band

Auto store

Hold down “AS” button (7) for 2 seconds or

longer.

6 stations in good reception will automati-

cally be stored to PRESET buttons (6) in

order, starting from a station whose fre-

quency is the lowest.

Radio reception

Press “FM” button (1).

Radio reception can be affected by envi-

ronment, atmospheric conditions, or radio

signal’s power and distance from the sta-

tion. Nearby mountains and buildings may

interfere or deflect radio reception, causing

poor reception. Poor reception or radio

static can also be caused by electric cur-

rent from overhead wires or high voltage

power lines.

Each time the button is pressed, the recep-

tion band will change as follows:

FM1

FM2

NOTE:

• Auto store can be released by pressing

“AS” button (7) while auto store is under

way.

Selecting the AM band

Press “AM” button (2).

• When the auto store is performed, the

station previously stored in the memory

at the position is overwritten.

• When there are fewer than 6 stations

that can be stored even if 1 round of

auto store operation is performed, no

station will be stored at the remaining

PRESET buttons (6).

Seek tuning

Press UP button (3) or DOWN button (4).

The unit stops searching for a station at a

frequency where a broadcast station is

available.

• 6 stations can be preset for FM1 and

FM2 in common, and 6 stations for AM

in auto store mode.

Manual tuning

Turn “TUNE/FLD PUSH SOUND” knob (5).

The frequency being received is displayed.

Auto store mode on/off

Press “AS” button (7).

Preset memory

1) Select the desired station.

2) Hold down a desired button ([1] to [6])

of the PRESET buttons (6) to which you

want to store the station for 2 seconds

or longer.

Each time the button is pressed, the mode

is switched as follows:

AS mode on AS mode off

5-46

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Using the RDS functions (Type A)

Display

(A)

(B)

EXAMPLE

(C)

(A) Band

(B) Channel number

(C) Program service (PS) name

(4)

(5)

(1)

(6) (3) (2)

52RM50540

(1) “TA” button

(2) “RDM/PTY” button

(3) “RPT/AF” button

(5) DOWN button

(4) UP button

(6) “DISP” button

5-47

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

TA (Traffic Announcement) on/off

Press “TA” button (1).

Each time it is pressed, TA adjustment is

changed as follows:

PTY (Program Type) search

1) Press “RDM/PTY” button (2) to select

PTY mode.

2) Press “RDM/PTY” button (2) while PTY

is displayed.

AF (Alternative Frequency) on/off

Press “RPT/AF” button (3).

Each time it is pressed, AF adjustment is

changed as follows:

Each time it is pressed, PTY adjust-

ment is changed as follows:

AF-ON/REG-OFF

AF-ON/REG-ON

AF-OFF/REG-OFF

OFF TP ON TA ON

NEWS

NOTE:

SPORTS

TALK

• For listening to only traffic information,

activate TA. Once traffic information

starts, the volume changes automatically.

• “TP” indicator lights up when TP (Traffic

Program) is on. It blinks when no TP data

is received.

AF: If the reception condition becomes

poor, the frequency of the same program

with good reception is automatically

searched.

POP

CLASSICS

REG: With regard to the automatically

searched frequency with AF activated, the

alternative frequency of the same program

is searched within the present region when

REG is activated.

• “TA” indicator lights while TA is activated.

On the other hand, “TA” indicator blinks if

the TP data cannot be received.

• If UP button (4) or DOWN button (5) is

pressed while TA or TP is set to on, the

unit searches for a TP station.

3) Press UP button (4) or DOWN button

(5) while PTY is displayed.

Search begins.

NOTE:

• If no TP station is received, the unit dis-

plays “TP NOTHING”.

NOTE:

“AF” indicator lights up when AF is on. In

addition, “REG” indicator lights up when

REG is on.

If no PTY information is received, the unit

displays “NOPTY”.

5-48

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

TA standby

At the moment traffic information is

received while the source is set to CD,

®

USB, iPod , AUX, DAB, or Blue-

®

tooth audio with TA activated, the source

is automatically changed to radio. After

reception of traffic information, the source,

which was selected before being changed

to radio, resumes.

NOTE:

If no TP station can be received while the

unit stands by for TA, it automatically

searches for a TP station.

EON (Enhanced Other Network)

When the EON data is received with TP or

TA activated, “EON” indicator lights up,

and the traffic information from a network

other than the currently received station is

allowed to be received.

Emergency announcement reception

Emergency announcements are automati-

cally received and displayed.

5-49

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Display

Listening to a CD

(A)

(1)

(2)

EXAMPLE

Type A

(3)

(B)

(4)

(5)

(A) Track number

(B) Play time

NOTE:

This product does not support 8 cm CD

(sometimes called as “mini single CD”, “3-

inch CD”, “CD3”, etc.).

(8) (6) (7)

(1)

(2)

Type B

(3)

(4)

(5)

(8) (6) (7)

52RM50550

(1) Insertion slot

(3) “CD” button

(5) DOWN button

(7) “RDM” button

(2) EJECT button

(4) UP button

(6) “RPT” button

(8) “DISP” button

5-50

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

NOTICE

• Never insert your finger or hand

into the CD insertion slot. Never

insert foreign objects into the CD

insertion slot.

• Never insert a CD with glue coming

out from adhesive tape or a rental

CD label or with a trace indicating

that adhesive tape or a rental CD

label has been removed. This may

cause the CD not to eject or result

in a malfunction.

If you forcefully try to push an

ejected CD inside the unit before auto

reloading, the disc surface might be

scratched.

Before reloading a CD, remove it

from the unit completely.

(A)

• CDs or CD-ROMs without mark (A) can-

not be used.

• Some discs recorded in CD-R/CD-RW

format may sometimes be impossible to

use.

Listening to a CD

When a CD is inserted, playback will auto-

matically start.

When a CD is already inside the unit,

press “CD” button (3) to start playback.

Loading a CD

Insert a CD in the insertion slot (1).

When the CD is loaded, it starts to play.

Selecting a track

• Press UP button (4) to listen to the next

track.

• Press DOWN button (5) twice to listen to

the previous track.

Ejecting a CD

Press EJECT button (2).

When the ignition switch is in “LOCK” posi-

tion or the engine switch is in LOCK (OFF)

mode, the CD being ejected for around 15

seconds or longer will automatically be

drawn inside the unit. (Auto reload func-

tion)

When DOWN button (5) is pressed

once, the track currently being played

will start from the beginning again.

• A CD is to be inserted with its label side

up.

• When there is a CD already in the unit, it

is impossible to insert another CD with-

out ejecting the CD in the unit. Do not

use force to insert a CD into the CD

insertion slot.

Fast forwarding/rewinding a track

• Hold down UP button (4) to fast forward

the track.

• Hold down DOWN button (5) to fast

rewind the track.

The backup eject function:

This function allows you to eject a CD by

pressing EJECT button (2) even when the

ignition switch is in “LOCK” position or the

engine switch is in LOCK (OFF) mode.

5-51

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Random playback

Display change

Press “RDM” button (7).

Press “DISP” button (8).

Each time the button is pressed, display

will change as follows:

Each time the button is pressed, the mode

will change as follows:

Play time

Disc title

Track title

OFF TRACK RANDOM

• TRACK RANDOM

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

Repeat playback

Press “RPT” button (6).

Each time the button is pressed, the mode

will change as follows:

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (8) for

1 second or longer can display the next

page.

OFF TRACK REPEAT

• TRACK REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

5-52

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Listening to a MP3/WMA/AAC disc

Type A

Display

(A)

(B)

EXAMPLE

(D)

(C)

(2)

(3)

(A) Folder number

(B) Track number

(C) Play time

(1)

(D) File type

(6) (4) (5)

Type B

(2)

(3)

(1)

(6) (4) (5)

52RM50560

(1) “TUNE/FLD PUSH SOUND” knob

(3) DOWN button

(2) UP button

(4) “RPT” button

(6) “DISP” button

(5) “RDM” button

5-53

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Selecting a folder

Turn “TUNE/FLD PUSH SOUND” knob (1)

to select a folder.

Random playback

Repeat playback

Press “RDM” button (5).

Press “RPT” button (4).

Each time the button is pressed, the mode

will change as follows:

Each time the button is pressed, the mode

will change as follows:

Selecting a track

• Press UP button (2) to listen to the next

track.

• Press DOWN button (3) twice to listen to

the previous track.

OFF

FOLDER RANDOM

ALL RANDOM

OFF

FILE REPEAT FOLDER REPEAT

When DOWN button (3) is pressed

once, the track currently being played

will start from the beginning again.

• FOLDER RANDOM

• FILE REPEAT

The random indicator “F.RDM” will light.

The tracks in the current folder will be

played in random order.

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

Fast forwarding/rewinding a track

• Hold down UP button (2) to fast forward

the track.

• Hold down DOWN button (3) to fast

rewind the track.

• ALL RANDOM

• FOLDER REPEAT

The random indicator “RDM” will light.

The tracks in the loaded disc will be

played in random order.

The repeat indicator “F.RPT” will light.

All tracks in the currently selected folder

will be played repeatedly.

5-54

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Display change

Points to remember when making MP3/

WMA/AAC files

Notes on MP3/WMA/AAC

Press “DISP” button (6).

Each time the button is pressed, display

will change as follows:

Common

What is MP3?

• High bit rate and high sampling fre-

quency are recommended for high qual-

ity sounds.

• Selecting VBR (Variable Bit Rate) is not

recommended. Selecting VBR may

cause display of incorrect playing time

and jumpiness of playback.

• Playback sound quality varies depend-

ing on the encoding environment. For

details, refer to the user manual of the

encoding software and the writing soft-

ware in use.

• An abbreviation of “MPEG audio layer3”,

MP3 is an audio compression format

that has become the standard format

among PC users. Its merit is that the

original audio data is compressed to

approximately 1/10 and high sound qual-

ity is maintained. This means that it is

possible to store the data of approxi-

mately 10 music CDs on a single CD-R/

RW disc, which in turn makes it possible

to play music for a long time without hav-

ing to change the disc.

Play time

Folder name

File name

Album name (MP3, AAC only)

Track title

NOTICE

What is WMA?

Artist name

• An abbreviation of “Windows Media

Audio,” WMA is an audio compression

format developed by Microsoft.

• WMA files for which the DRM (Digital

Rights Management) function is on can-

not be played.

Never use “.mp3”, “.wma” or “.m4a”

as a file name extension if it is not in

the MP3/WMA/AAC format file. Fail-

ure to observe this may result in

damage to the speaker due to noise

production.

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the disc currently

being played.

Windows Media and the Windows^®logo

are trademarks or registered trademarks of

Microsoft Corporation in the United States

and other countries.

TM

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (6) for

1 second or longer can display the next

page.

What is AAC?

• An abbreviation of “Advanced Audio

Coding,” AAC is an audio compression

format used by MPEG2 and MPEG4.

5-55

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Recording MP3/WMA/AAC files on a CD

media

• It is recommended not to write both CD-

DA files and MP3/WMA/AAC files on a

disc.

• If both CD-DA files and MP3/WMA/AAC

files are on the same disc, tracks may

not be played in the correct order or

some tracks may not be played at all.

• When storing both MP3 data and WMA

data on the same disc, sort and place

them in different folders.

• Do not write files other than MP3/WMA/

AAC files and unnecessary folders on a

disc.

Compression formats

MP3

• Bit rate:

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Sampling frequency

:

MPEG1 Audio Layer III: 32 k/44.1 k/

48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/

24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/

12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• MP3/WMA/AAC files should be named

to meet the standards and the file sys-

tem specifications as shown below.

• The file extension “.mp3”, “.wma” or

“.m4a” should be assigned to files based

on their format independently.

• You may encounter a trouble in playing

MP3/WMA/AAC files or displaying infor-

mation of MP3/WMA/AAC files depend-

ing on the writing software or CD

recorder in use.

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Supported file systems

ISO 9660 Level 1/Level 2, Joliet, Romeo

• This unit does not have a playlist func-

tion.

• It is recommended to write discs in Disc-

at-Once mode even though Multi-ses-

sion mode is supported. These modes

are the methods for writing audio data in

CD.

Maximum number of files/folders

• Maximum number of files: 512

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-56

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Listening to files stored in a USB device

Type A

Display

(A)

(B)

EXAMPLE

(D)

(C)

(3)

(4)

(A) Folder number

(B) Track number

(C) Play time

(1)

(2)

(D) File type

(7) (5) (6)

NOTICE

Do not connect any USB device other

than a USB memory or a USB audio

player. Do not connect multiple USB

devices to the USB connector using a

USB hub, etc. Supplying power to

multiple USB devices from the con-

nector could cause overheating and

smoking.

Type B

(3)

(4)

(1)

(2)

(7) (5) (6)

52RM50570

(1) “MEDIA” button

(3) UP button

(2) “TUNE/FLD PUSH SOUND” knob

(4) DOWN button

(5) “RPT” button

(7) “DISP” button

(6) “RDM” button

5-57

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Selecting a USB device mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Random playback

• FOLDER REPEAT

Press “RDM” button (6).

The repeat indicator “F.RPT” will light.

All the tracks in the folder currently

selected will be played repeatedly.

Each time the button is pressed, the mode

will change as follows:

Display change

USB (iPod^®) (if equipped)

Press “DISP” button (7).

Each time the button is pressed, display

will change as follows:

OFF

FOLDER RANDOM

ALL RANDOM

®

Bluetooth audio (if equipped)

AUX (if equipped)

Play time

• FOLDER RANDOM

The random indicator “F.RDM” will light.

The tracks in the currently selected

folder will be played in random order.

• ALL RANDOM

Folder name

File name

Selecting a folder

Turn “TUNE/FLD PUSH SOUND” knob (2)

to select the desired folder.

The random indicator “RDM” will light.

The tracks in the connected USB device

will be played in random order.

Album name (MP3, AAC only)

Track title

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

Repeat playback

Press “RPT” button (5).

Each time the button is pressed, the mode

will change as follows:

Artist name

NOTE:

• “NO TITLE” will be displayed when there

is no text information in the file currently

being played.

• If text data contains more than 16 char-

acters, “>” mark will appear at the right

end. Holding down “DISP” button (7) for

1 second or longer can display the next

page.

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

OFF

FILE REPEAT

FOLDER REPEAT

• FILE REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

5-58

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

USB device connection

Compression formats

Notes on USB device

• When connecting a USB device, check

that the connector is pushed all the way

into the port.

MP3

• Bit rate

:

Compatible USB devices

• USB mass storage class

MPEG1 Audio Layer III: 32 k - 320 kbps

MPEG2 Audio Layer III: 8 k - 160 kbps

MPEG2.5 Audio Layer III: 8 k - 160 kbps

• Do not leave the USB device for long

periods of time inside the vehicle where

the temperature can rise too high.

• Back up any important data beforehand.

We cannot accept responsibility for any

lost data.

• It is recommended not to connect a USB

device that contains data files other than

MP3/WMA/AAC format.

For details as to whether your USB

memory/USB audio is compatible with

USB mass storage class, please contact

the USB memory/USB audio manufac-

turer.

• USB standard compatibility 1.1/2.0 full

speed

• File system FAT12/16/32, VFAT

• Maximum current less than 1.0 A

• If devices such as USB hub, extension

cable are connected to the audio sys-

tem, it may not be recognized. In such

case, connect the USB device directly to

the audio system.

• Devices such as MP3 player/mobile

phone/digital camera may not be recog-

nized by the audio system for playing

music.

• Sampling frequency

:

MPEG1 Audio Layer III: 32 k/44.1 k/48 kHz

MPEG2 Audio Layer III: 16 k/22.05 k/24 kHz

MPEG2.5 Audio Layer III: 8 k/11.025 k/12 kHz

WMA (Ver. 7, Ver. 8, Ver. 9*)

• Bit rate: CBR 32 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* WMA 9 Professional/LossLess/Voice are

not supported.

Recording MP3/WMA/AAC files on a

USB device

• Playback or display may not be possible

depending on the type of USB device in

use or the condition of the recording.

• Depending on the connected USB mem-

ory, the files may be played in different

order from the stored one.

AAC*

• Bit rate: ABR 16 k - 320 kbps

• Sampling frequency: 32 k/44.1 k/48 kHz

* Apple Lossless is not supported.

Maximum number of files/folders

• Maximum number of files: 2500

• Maximum number of files in a folder: 255

• Maximum depth of tree structure: 8

• Maximum number of folders: 255

(Root folder is included.)

5-59

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Display

®

Listening to an iPod

(A)

EXAMPLE

Type A

(B)

(C)

(3)

(4)

(7) (5) (6)

(A) Track title

(1)

(B) Track number

(C) Play time

(2)

®

iPod is a trademark of Apple Inc., regis-

tered in the U.S. and other countries.

(8)

Type B

(3)

(4)

(7) (5) (6)

(1)

(2)

(8)

52RM50580

(1) “MEDIA” button

(3) UP button

(2) “TUNE/FLD PUSH SOUND” knob

(4) DOWN button

(5) “RPT” button

(7) “DISP” button

(6) “RDM” button

(8) PRESET buttons ([1] to [6])

5-60

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

®

Selecting an iPod mode

Press “MEDIA” button (1).

Random playback

Display change

Press “RDM” button (6).

Press “DISP” button (7).

Each time the button is pressed, display

will change as follows:

Each time the button is pressed, the mode

will change as follows:

Each time the button is pressed, the mode

will change as follows:

USB (iPod^®) (if equipped)

Playlist name /

OFF

SONG RANDOM

ALBUM RANDOM

Track title (Playlist mode only)

®

Bluetooth audio (if equipped)

Artist name /

Track title

AUX (if equipped)

• SONG RANDOM

Album name /

Track title

The random indicator “RDM” will light.

®

The tracks in the iPod will be played in

random order.

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

Track title /

Play time

• ALBUM RANDOM

The random indicator “F.RDM” will light.

®

The albums in the iPod will be played in

random order.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

NOTE:

If text data contains more than 16 charac-

ters, “>” mark will appear at the right end.

Holding down “DISP” button (7) for 1 sec-

ond or longer can display the next page.

Repeat playback

Press “RPT” button (5).

Each time the button is pressed, the mode

will change as follows:

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

OFF SONG REPEAT

• SONG REPEAT

The repeat indicator “RPT” will light.

The track currently being played will be

played repeatedly.

5-61

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

®

Playing mode selection

iPhone is a trademark of Apple Inc., reg-

®

Notes on iPod

1) Press the button numbered [6] of PRE-

SET buttons (8) for 1 second or longer.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2).

istered in the U.S. and other countries.

®

Supported iPod

* Some functions may not be available

depending on the model of iPod .

* Apple is not responsible for the opera-

tion of this device or its compliance with

safety and regulatory standards.

®

• iPod touch (6th generation)

®

• iPod touch (5th generation)

Each time the knob is turned, the mode

will change as follows:

• iPod touch (4th generation)

• iPod touch (3rd generation)

• iPod touch (2nd generation)

• iPod touch (1st generation)

®

iPod connection

• Make sure to detach the iPod after

turning the ignition switch to “LOCK”

position or pressing the engine switch to

change the ignition mode to LOCK

• iPod classic

®

PLAYLIST

ARTIST

®

• iPod nano (7th generation)

• iPod nano (6th generation)

• iPod nano (5th generation)

• iPod nano (4th generation)

®

ALBUM

(OFF). The iPod may not be shut down

when it is being connected and may

result in battery depletion.

• iPod nano (3rd generation)

• iPod nano (2nd generation)

SONGS

• iPod nano (1st generation)

• iPod (5th generation)

• iPhone 6S Plus

®

• Do not connect iPod accessories such

®

PODCAST

GENRE

as an iPod remote control or head-

®

phones while connecting the iPod with

• iPhone 6S

the unit. The unit may not operate cor-

rectly.

®

• iPhone 6 Plus

• iPhone 6

AUDIOBOOK

®

• iPhone 5S

®

• iPhone 5C

®

• iPhone 5

3) Press “TUNE/FLD PUSH SOUND”

knob (2) to select the desired mode.

®

• iPhone 4S

®

• iPhone 4

®

• iPhone 3GS

NOTE:

®

• iPhone 3G

• When the button numbered [6] of PRE-

SET buttons (8) is pressed, the previous

mode will be displayed.

®

• iPhone

5-62

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

AUX connection

AUX function

To listen to auxiliary audio sources (sold

separately) through the unit, follow the

instruction below.

EXAMPLE

Type A

1) Connect the auxiliary audio source to

the AUX/USB socket (separately

attached) with an AUX cable.

2) Press “MEDIA” button (1).

Each time the button is pressed, the

mode will change as follows:

(1)

®

USB (iPod ) (if equipped)

®

Bluetooth audio (if equipped)

AUX (if equipped)

Type B

CAUTION

• Before connection, mute the unit,

and also keep the volume of the

auxiliary audio source within a

range that will not cause distortion.

• When the audio source is turned

off, noise may be emitted. Be sure

to turn off the unit or switch to

another mode before turning off the

audio source.

(1)

52RM50590

(1) “MEDIA” button

5-63

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

NOTE:

• Please consult your place of purchase

for details about whether a given auxil-

iary audio source can be connected and

the proper auxiliary cord to use.

• The volume and tone controls of the

auxiliary audio source can be adjusted

on the unit.

• In AUX mode, the volume setting is dif-

ferent from another mode.

5-64

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Steering switch

®

Bluetooth hands-free

(10)

EXAMPLE

Type A

(4)

(9)

(5)

(1)

(2)

(7)

(8)

(6)

(3)

Type B

52RM50460

®

(4)

(6) Bluetooth setup button (on steering

wheel)

(7) OFF HOOK button

(8) ON HOOK button

(9) MUTE switch

(5)

(1)

(10) “VOL” switch

(2)

(3)

52RM50600

(1) “TUNE/FLD PUSH SOUND” knob

(3) PRESET buttons

(2) “VOL PUSH PWR” knob

(4) BACK button

®

(5) Bluetooth setup button (on control panel)

5-65

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Phone registration

6) When the pairing with the phone is

established, automatic transfer of the

phonebook and the call history

becomes selectable. The automatic

transfer starts with “Yes” and it does not

with “No”.

Adjusting the listening volume

• Turn “VOL PUSH PWR” knob (2) during

a call.

To use the hands-free function with this

unit, it is required to register the phone

in advance.

Turning it clockwise increases the vol-

ume;

turning

it

counterclockwise

decreases the volume.

7) Press ON HOOK button (8).

• Press “VOL” switch (10) during a call.

Pressing the switch up increases the vol-

ume; pressing the switch down

decreases the volume.

NOTE:

• Up to 5 phones can be registered.

• To set up a new phone, disconnect the

audio player from the unit. Connect the

audio player again after phone setup is

completed if necessary.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Adjusting the ring volume

• When registering an additional phone,

repeat Step from 1).

• Turn “VOL PUSH PWR” knob (2) while a

call is coming in.

• When attempts to establish the pairing

fail within 60 seconds, the connecting

operation will be canceled. Try to estab-

lish the pairing again or refer to the man-

ual of the phone in use for how to

establish the pairing with the phone.

Turning it clockwise increases the vol-

Receiving a call

Press OFF HOOK button (7) to receive a

call.

ume;

turning

it

counterclockwise

decreases the volume.

• Press “VOL” switch (10) during a call.

Pressing the switch up increases the vol-

ume; pressing the switch down

decreases the volume.

®

1) Press the Bluetooth setup button (5)

Ending a call

Press ON HOOK button (8) to end a call.

or (6).

®

The Bluetooth setup menu will be dis-

played.

Rejecting a call (only for supported

models)

Press ON HOOK button (8) to reject a

incoming call.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Pairing”, and press the

knob (1) to determine the selection.

Mute of hands-free microphone

Press MUTE switch (9) to mute the micro-

phone. To cancel the mute, press MUTE

switch (9) again.

®

4) Select “My Car” from the Bluetooth

menu of the phone and establish the

pairing.

Refer to the manual of the phone in use

for further information.

5) Enter the passkey displayed on the unit

to the phone.

5-66

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Adjusting the call or ringtone volume

Follow the instructions below to adjust the

call or ringtone volume.

Dialing using missed/incoming/

outgoing calls

Follow the instructions below to dial to the

previously dialed number again.

• Pressing “Confirm” after selecting “Add

Speed Dial” can register the selected

number in the speed dial.

• Pressing “Confirm” after selecting

“Delete” can delete the selected number

from the call history.

®

1) Press the Bluetooth setup button (5)

or (6).

®

The Bluetooth setup menu will be dis-

NOTE:

played.

Up to 30 phone numbers of the latest calls

can be stored. (30 calls including missed,

received and dialed call)

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Sound Setting”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Call Volume” or “Ringtone

Volume”, and press the knob (1) to

determine the selection.

Deletion of call history

Follow the instructions below to delete a

missed/incoming/outgoing call history.

®

1) Press OFF HOOK button (7).

1) Press the Bluetooth setup button (5)

®

The Bluetooth phonebook menu will

or (6).

®

be displayed.

The Bluetooth setup menu will be dis-

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Calls”, “Missed Calls”,

“Incoming Calls” or “Outgoing Calls”,

and press the knob (1) to determine the

selection.

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

The current call or ringtone volume will

be displayed.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the desired call or ringtone

volume, and press the knob (1) to

determine the selection.

To dial from the dialed history or the

received history, select “All Calls”,

“Missed Calls”, “Incoming Calls” or

“Outgoing Calls” respectively.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the desired number, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Dial”, and press the knob

(1) or OFF HOOK button (7) to dial to

the selected number.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete History”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Missed Calls”, “Incoming

Calls”, or “Outgoing Calls”, and press

the knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a number to be deleted or

“ALL”, and press the knob (1) to deter-

mine the selection.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-67

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?” or “Delete All?”,

and press the knob (1) to determine the

selection.

8) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Overwrite All” or “Add One

Contact”, and press the knob (1) to

determine the selection.

Transfer of call history (Call History)

Follow the instructions below to transfer

call history of the registered phone.

®

1) Press the Bluetooth setup button (5)

“Rewrite All (MAX1000): Ok?” or “Rest

of Memory XXXX: Ok?” will be dis-

played.

or (6).

®

The Bluetooth setup menu will be dis-

played.

6) Press or turn “TUNE/FLD PUSH

SOUND” knob (1) to select “Confirm”,

and press the knob (1) to determine the

selection.

7) Transfer contacts from the phone.

When the registration is completed, the

“Setup Phonebook” will be displayed.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Call History”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Overwrite Call History?”,

and press the knob (1) to determine the

selection.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

Registration in Phonebook

Follow the instructions below to register

phone numbers in the Phonebook of the

unit.

NOTE:

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

®

1) Press the Bluetooth setup button (5)

or (6).

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to transfer the call history from

the phone.

®

The Bluetooth setup menu will be dis-

• Up to 1000 numbers can be registered in

Phonebook.

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Add Contacts”, and press

the knob (1) to determine the selection.

5-68

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Automatic transfer of phonebook/call

history

Making a call by phonebook

Deletion of registered data (Delete

Entry)

Follow the instructions below to dial a num-

ber registered in phonebook.

You can select whether or not the device

transfers the phonebook and the call his-

tory automatically when the phone is regis-

tered.

Follow the instructions below to delete a

number registered in phonebook.

1) Press OFF HOOK button (7).

®

The Bluetooth phonebook menu will

1) Press the Bluetooth setup button (5)

be displayed.

or (6).

®

Follow the instructions below to select.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Phonebook”, and press

the knob (1) to determine the selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to make a call, and press the

knob (1) to determine the selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

The Bluetooth setup menu will be dis-

®

1) Press the Bluetooth setup button (5)

played.

or (6).

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete Contacts”, and

press the knob (1) to determine the

selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to delete or “ALL”, and press

the knob (1) to determine the selection.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

delete, and press the knob (1) to deter-

mine the selection.

®

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “A.Transfer”, and press the

knob (1) to determine the selection.

4) Pressing “TUNE/FLD PUSH SOUND”

knob (1) switches between “A.transfer

On” and “A.transfer Off”.

5) Selecting “Go Back” or pressing the

BACK button (4) stores displayed set-

ting and the previous menu is dis-

played.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

make a call, and press the knob (1) to

determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Dial”, and press the knob

(1) or OFF HOOK button (7).

The displayed number or the number

registered with the displayed name will

be dialed.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?” or “Delete All?”,

and press the knob (1) to determine the

selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

5-69

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

NOTE:

register in speed dial, and press the

knob (1) to determine the selection.

One-touch call (Speed dial)

Follow the instructions below to dial the

number assigned to each of the PRESET

buttons (3).

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Choose Preset”, and

press one of PRESET buttons (3) to

which the selected number is to be

1) Press OFF HOOK button (7).

®

Registration in speed dial

The Bluetooth phonebook menu will

Follow the instructions below to assign a

number to one of PRESET buttons (3) to

use as the speed dial.

assigned. If

a

number is already

be displayed.

assigned to the selected button, a con-

firmation message will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a confirmation message,

and press the knob (1) to complete the

assignment.

Pressing one of PRESET buttons (3)

can skip step 2) and the 1st line of step

3).

®

1) Press the Bluetooth setup button (5)

or (6).

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Speed Dials”, and press

the knob (1) to determine the selection.

3) Press one of PRESET buttons (3).

The assigned number will be displayed.

If no number is assigned, “No Entry” is

displayed.

®

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Telephone”, and

press the knob (1) to determine the

selection.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the assignment.

When the assignment is completed, the

“Setup Phonebook” will be displayed.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Phonebook”, and

press the knob (1) to determine the

selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Add Speed Dial”, and

press the knob (1) to determine the

selection.

4) Press OFF HOOK button (7).

The selected number will be dialed.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the initial of the name you

would like to register in speed dial, and

press the knob (1) to determine the

selection.

The registered numbers will be dis-

played in sequence. If names have

been registered together with numbers,

the names will be displayed.

Turn “TUNE/FLD PUSH SOUND” knob

(1) to select the name you would like to

5-70

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Deletion of speed dial (Del Speed Dial)

Display of device data (Device Name)

Reset to the factory defaults

Follow the instructions below to delete the

Follow the instructions below to display the

Follow the instructions below to reset all

the settings to the factory defaults.

®

number assigned for the speed dial.

1) Press OFF HOOK button (7).

BD (Bluetooth

device name.

Device) address and

®

1) Press the Bluetooth setup button (5)

®

The Bluetooth phonebook menu will

1) Press the Bluetooth setup button (5)

or (6).

®

be displayed.

The Bluetooth setup menu will be dis-

®

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Speed Dials”, and press

the knob (1) to determine the selection.

3) Press one of PRESET buttons (3) to

which the number to be deleted is

assigned.

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Initialize”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Initialize”, and press

the knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “All Initialize”, and press

the knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to start the reset.

If the number is not registered, “No

Entry” is displayed.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Bluetooth Info”, and press

the knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Device Name” or “Device

Address”, and press the knob (1) to dis-

play the device name or the BD (Blue-

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete”, and press the

knob (1) to determine the selection.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Del Speed Dial”, and

press the knob (1) to determine the

selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to complete the deletion.

®

tooth Device) address.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-71

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Selection of phone (Select Phone)

Follow the instructions below to select a

phone to be paired with from the registered

phones.

List of phones (List Phones)

Follow the instructions below to display the

names of the registered phones in

sequence.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Passkey”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Enter New Passkey”, and

press the knob (1) to determine the

selection.

5) Press or turn “TUNE/FLD PUSH

SOUND” knob (1) to select “Confirm”.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a number for the first digit,

and press the knob (1) to determine the

selection. Select and determine num-

bers for the second, third and fourth

digits in order in the same manner.

When not entering up to the eighth

digit, enter blanks for the successive

digits.

®

1) Press the Bluetooth setup button (5)

or (6).

®

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a phone to be paired with,

and press the knob (1) to determine the

selection.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

The names of the registered phones

are displayed in sequence.

NOTE:

7) Press “TUNE/FLD PUSH SOUND”

knob (1) to determine the passkey set-

ting.

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Select”, and press the

knob (1) to determine the selection.

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

NOTE:

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (passkey).

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

®

1) Press the Bluetooth setup button (5)

®

• The Bluetooth ready audio device will

or (6).

®

be disconnected when the phone is

selected.

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

5-72

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Deletion of phone information (Delete

Phone)

BT function on/off (BT Power)

Follow the instructions below to turn on/off

®

Follow the instructions below to delete the

registered phone information.

the Bluetooth function.

®

1) Press the Bluetooth setup button (5)

®

1) Press the Bluetooth setup button (5)

or (6).

®

or (6).

The Bluetooth setup menu will be dis-

®

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “BT Power”, and press the

knob (1) to determine the selection.

4) Press “TUNE/FLD PUSH SOUND”

knob (1) to select “BT Power On” or “BT

Power Off”.

2) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Setup Bluetooth”, and

press the knob (1) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “List Phone”, and press the

knob (1) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select a phone to be deleted, and

press the knob (1) to determine the

selection.

NOTE:

5) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete”, and press the

knob (1) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Delete?”, and press the

knob (1) to determine the selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(1) to select “Confirm”, and press the

knob (1) to determine the selection.

• When the BT function is turned off, the

connection between this unit and the

registered phone in use will be discon-

nected.

• When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

NOTE:

When selecting “Go Back” or pressing

BACK button (4), the previous menu will

be displayed.

5-73

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Steering switch

®

Bluetooth audio

EXAMPLE

Type A

(3)

(4)

(7)

(1)

(8)

(2)

52RM50470

®

(5)

(6)

(8) Bluetooth setup button (on steering

wheel)

Type B

Display

(A)

(3)

(4)

(7)

(1)

(B)

(2)

(A) Track number

(B) Play time

(5)

(6)

52RM50610

(1) “MEDIA” button

(3) UP button

(2) “TUNE/FLD PUSH SOUND” knob

(4) DOWN button

(5) “DISP” button

(6) BACK button

®

(7) Bluetooth setup button (on control panel)

5-74

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Registration of audio devices

NOTE:

Fast forwarding/rewinding a track

• Hold down UP button (3) to fast forward

the track.

• Hold down DOWN button (4) to fast

rewind the track.

• When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

®

To use Bluetooth ready audio devices

with this unit, it is required to register the

devices.

• When registering additional audio

devices, repeat Step from 1).

NOTE:

®

NOTE:

Selecting Bluetooth audio mode

Press “MEDIA” button (1).

Each time the button is pressed, the mode

will change as follows:

Some functions may not be available

®

• To set up a new audio player, disconnect

the phone from the unit. Connect the

phone after audio player setup is com-

pleted if necessary.

depending on Bluetooth audio.

Display change

Press “DISP” button (5).

Each time the button is pressed, display

will change as follows:

• When attempts to establish the pairing

fail within 60 seconds, the connecting

operation will be canceled. Try to estab-

lish the pairing again or refer to the audio

player manual for assistance with the

pairing process.

USB (iPod^®) (if equipped)

®

Bluetooth audio (if equipped)

Play time

AUX (if equipped)

®

1) Press the Bluetooth setup button (7)

Track name

Artist name

Album name

or (8).

®

Selecting a group (only for supported

models)

Turn “TUNE/FLD PUSH SOUND” knob (2)

to select a group.

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

Selecting a track

• Press UP button (3) to listen to the next

track.

• Press DOWN button (4) twice to listen to

the previous track.

When DOWN button (4) is pressed

once, the track currently being played

will start from the beginning again.

NOTE:

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Pairing”, and press the

knob (2) to determine the selection.

If text data contains more than 16 charac-

ters, “>” mark will appear at the right end.

Holding down “DISP” button (5) for 1 sec-

ond or longer can display the next page.

®

4) Select “My Car” from the Bluetooth

menu of the audio player and establish

the pairing.

Refer to the manual of the audio player

in use for further information.

5) Enter the passkey displayed on the unit

to the audio player.

5-75

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Selection of audio device (Select Audio)

Follow the instructions below to select an

audio device to be paired with from the

registered audio devices.

List of audio devices (List Audio)

Follow the instructions below to display the

names of the registered audio devices in

sequence.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Passkey”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Enter New Passkey”, and

press the knob (2) to determine the

selection.

5) Press or turn “TUNE/FLD PUSH

SOUND” knob (2) to select “Confirm”.

6) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select a number for the first digit,

and press the knob (2) to determine the

selection. Select and determine num-

bers for the second, third and fourth

digits in order in the same manner.

When not entering up to the eighth

digit, enter blanks for the successive

digits.

®

1) Press the Bluetooth setup button (7)

or (8).

®

The Bluetooth setup menu will be dis-

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select an audio device to be

used, and press the knob (2) to deter-

mine the selection.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

The names of registered audio devices

will be displayed in sequence.

NOTE:

7) Press “TUNE/FLD PUSH SOUND”

knob (2) to determine the passkey set-

ting.

5) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Select”, and press the

knob (2) to determine the selection.

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

NOTE:

Passkey setting (Set Passkey)

Follow the instructions below to set the

security number (Passkey).

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

• When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

®

1) Press the Bluetooth setup button (7)

• The phone will be disconnected when

or (8).

®

the Bluetooth ready audio device is

The Bluetooth setup menu will be dis-

selected.

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

5-76

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Deletion of audio device information

(Delete Audio)

®

Disclaimer for Bluetooth function

Remote audio controls (if equipped)

Follow the instructions below to delete the

registered audio device information.

• Depending on compatibility of mobile

Controlling basic functions of the audio

system is available using the switches on

the steering wheel.

®

phone models, no Bluetooth function

®

1) Press the Bluetooth setup button (7)

can be used, or some Bluetooth func-

or (8).

tions may be restricted.

®

The Bluetooth setup menu will be dis-

• Connectivity or voice quality may get

affected depending on circumstances.

• After the ignition switch is turned to “ON”

position or the engine switch is pressed

to change the ignition mode to ON, the

audio system takes few seconds to

played.

2) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Setup Bluetooth”, and

press the knob (2) to determine the

selection.

3) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “List Audio”, and press the

knob (2) to determine the selection.

4) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select an audio device to be

deleted, and press the knob (2) to

determine the selection.

(1) (3) (4)

(4)

®

detect and connect to the Bluetooth

device (if already paired).

(2)

5) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Delete”, and press the

knob (2) to determine the selection.

6) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Delete?”, and press the

knob (2) to determine the selection.

7) Turn “TUNE/FLD PUSH SOUND” knob

(2) to select “Confirm”, and press the

knob (2) to complete the deletion.

52RM50480

NOTE:

When selecting “Go Back” or pressing

BACK button (6), the previous menu will

be displayed.

5-77

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Adjusting the volume

Selecting the radio station (AM, FM1,

FM2, DAB1, DAB2 mode)

• To select the next preset station, press

“>” of the switch (4) only for a moment.

• To select the previous preset station,

press “<” of the switch (4) only for a

moment.

• To scan a higher frequency radio station,

press “>” of the switch (4) for 1 second

or longer.

• To scan a lower frequency radio station,

press “<” of the switch (4) for 1 second

or longer.

• To increase the volume, press the “VOL”

switch (1) up. The volume will continue

to increase until the switch is released.

• To decrease the volume, press the

“VOL” switch (1) down. The volume will

continue to decrease until the switch is

released.

• To mute the sound, press the switch (2).

Selecting the mode

Press the switch (3).

Each time the button is pressed, the mode

will change as follows:

®

Selecting the track (CD, USB (iPod ),

®

Bluetooth audio mode)

AM (Radio)

• To skip to the next track, press “>” of the

switch (4) only for a moment.

FM1 (Radio)

FM2 (Radio)

DAB1 (if equipped)

DAB2 (if equipped)

CD

• To skip to the previous track, press “<” of

the switch (4) twice only for a moment.

When the switch (4) is pushed down

once only for a moment, the track cur-

rently being played will start from the

beginning again.

Fast forwarding/rewinding a track

• To fast forward a track, press “>” of the

switch (4) for 1 second or longer.

• To fast rewind a track, press “<” of the

switch (4) for 1 second or longer.

®

Bluetooth audio (if equipped)

AUX (if equipped)

®

USB (iPod ) (if equipped)

It is possible to turn on the audio system

by pressing the switch (3).

5-78

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

The anti-theft function is intended to dis-

courage thefts. For example, when the

audio system is installed in another vehi-

cle, it will become unable to operate.

This function works by entering a Personal

Identification Number (PIN).

When the unit is disconnected from its

power source, such as when the audio

system is removed or the lead-acid battery

is disconnected, the unit will become inop-

erable until the PIN is reentered.

Anti-theft feature

EXAMPLE

Type A

(3)

(4)

(1)

(2)

Type B

(3)

(4)

(1)

(2)

52RM50620

(1) “VOL PUSH PWR” knob

(3) UP button

(2) PRESET buttons ([1] to [6])

(4) “TUNE/FLD PUSH SOUND” knob

5-79

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Setting the anti-theft function

1) Press “VOL PUSH PWR” knob (1) to

power off.

2) Hold down the buttons numbered [1]

and [6] of PRESET buttons (2) and

press “VOL PUSH PWR” knob (1).

“SECURITY” will be displayed.

3) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

Canceling the anti-theft feature

To cancel the anti-theft function, delete the

registered PIN.

1) Press “VOL PUSH PWR” knob (1) to

power off.

2) Hold down the buttons numbered [1]

and [6] of PRESET buttons (2) and

press “VOL PUSH PWR” knob (1).

“PIN ENTRY” will be displayed.

3) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

4) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

Confirming the Personal Identification

Number (PIN)

When the main power source is discon-

nected such as when the lead-acid battery

is replaced, etc, it is required to enter the

PIN to operate the unit again.

1) Set the ignition switch to “ACC” posi-

tion or the ignition mode to ON.

“SECURITY” will be displayed.

2) Press UP button (3) and the button

numbered [1] of PRESET buttons (2)

simultaneously.

3) Enter a 4-digit number to be registered

as PIN using the buttons numbered [1]

- [4] of PRESET buttons (2).

5) Hold

down

“TUNE/FLD

PUSH

SOUND” knob (4) for 1 second or lon-

ger to set the anti-theft function.

5) Hold

down

“TUNE/FLD

PUSH

4) Hold

down

“TUNE/FLD

PUSH

SOUND” knob (4) for 1 second or lon-

ger to delete the registered PIN. The

indication “----” will be displayed and

the anti-theft function will be canceled.

SOUND” knob (4) for 1 second or lon-

ger.

When the same PIN as registered is

entered, the power of the audio system

will be turned off automatically and it

will become operable again.

NOTE:

Take a note of the registered PIN and keep

it for the future use.

NOTE:

To change your PIN, first delete your cur-

rent PIN, and then set a new one.

NOTE:

If an incorrect PIN is entered, “ERROR”

and the total number of incorrect entry

attempts will be displayed.

If an incorrect PIN is entered 10 times or

more, “HELP” will be displayed and the

audio system will become inoperable.

5-80

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Troubleshooting

When encountering a problem, check and follow the instructions below.

If the described suggestions do not solve the problem, it is recommended to take the unit to an authorized SUZUKI dealer.

Problem

Possible cause

Possible solution

Common

When “SECURITY” is displayed, enter

the PIN.

When “HELP” is displayed, contact an

authorized SUZUKI dealer.

Unable to operate

The security function is on.

Fuse is blown.

Unable to turn on the power

(No sound is produced)

Contact an authorized SUZUKI dealer.

Radio

It may not be exactly tuned in to the sta-

tion.

Much noise

Tune it in exactly to the station.

Pick up a station by manual tuning.

Turn off AF.

There may be no station emitting signals

powerful enough.

Unable to receive by auto tuning

If AF is on, the unit searches for RDS sta-

tions only.

CD

The disc is dirty.

Wipe the disc with a soft cloth.

Sound skips or noise produced

The disc has a major scratch or is

warped.

Replace the disc with the one which has

no scratch and warp.

5-81

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Problem

Possible cause

Possible solution

MP3/WMA/AAC

The disc contains unsupported formatted

data.

No playback

Check the file format.

Sound skipping may occur when playing

VBR (Variable Bit Rate) files.

Sound skips or noise produced

USB

It is not recommended to play VBR files.

There is no supported format file to play

on this unit.

Check the file format.

Playback does not start when the USB

device is connected

The current consumption of the USB

device exceeds 1.0 A.

Use a USB device with a current con-

sumption lower than 1.0 A.

®

Bluetooth

The distance between this unit and the

Bluetooth ready device is too far, or a

®

Change the location of the Bluetooth

metallic object may be located between

the Bluetooth ready device and this unit.

ready device.

®

Pairing failed

®

Refer to the manual of the Bluetooth

®

The Bluetooth function of the Bluetooth

ready device. (Some devices have the

power saving function that automatically

activates after a certain time.)

ready device is off.

Your current location may be out of ser-

vice area.

Drive your vehicle to the service area of

the phone.

Unable to receive a call

The voice quality of hands-free is low

(Distortion, noise etc.)

Another wireless device may be located

near the unit.

Switch off the wireless device or keep it

away from the unit.

5-82

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Error display messages

Display

Possible cause

Possible solution

CD

Insert the disc with its label side up.

Check the disc if it is not warped or is free of flaws.

When “ERROR 1” does not disappear even when a nor-

mal disc is inserted, contact an authorized SUZUKI

dealer.

“ERROR 1”

The disc cannot be read.

When the CD is in the unit, press the CD eject button to

remove the disc.

When the disc cannot be ejected, contact an authorized

SUZUKI dealer.

The player developed an error of an

unidentified cause.

“ERROR 3”

®

USB/iPod

“USB ERROR”

The USB device is disconnected.

Check the connection of the USB device.

Impossible to communicate correctly with

the USB device.

Unplug the USB device and plug it again.

Check the USB device.

“ERROR 2”

“ERROR 3”

“ERROR 4”

Unplug the USB device and plug it again.

When “ERROR 3” does not disappear, contact an autho-

rized SUZUKI dealer.

Inoperable due to an unidentified cause.

The current consumption of the USB

device exceeds 1.0 A.

Check the USB device.

5-83

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

Display

Possible cause

Possible solution

®

Bluetooth

®

Disconnect the Bluetooth ready device and connect it

The player developed an error of an

unidentified cause.

again.

“ERROR 1”

When “ERROR 1” does not disappear, contact an autho-

rized SUZUKI dealer.

“Connection Failed”

“Memory Full”

Failed to establish pairing or connection

Try to establish the pairing or connection again.

Delete registered data of unnecessary number in phone-

book and try to transfer the register phone numbers in

the phonebook again.

Reached the limit for the number of phone-

book data in transfer

“Not Available”

Inoperable during driving

Operate the system after pulling over your car.

5-84

52RM0-01E

OTHER CONTROLS AND EQUIPMENT

MEMO

5-85

52RM0-01E

OTHER CONTROLS AND EQUIPMENT -> Audio system (Type A / Type B) (if equipped) for Your Suzuki Swift 4 Door First generation (2004-2009)

Related Topics

Popular Owner Manuals

Latest Owner Manuals