Get Interior features Guide for Toyota Avalon 4 Door Fourth Generation (2013-2018)

259

Interior features

5

5-1. Using the air

5-4. Other interior features

conditioning system

and defogger

Other interior features....... 285

• Sun visors..................... 285

• Vanity mirrors................ 285

• Clock............................. 286

Automatic air conditioning

system............................. 260

Seat heaters/

seat ventilators................ 269

• Outside temperature

display........................... 287

5-2. Using the interior lights

• Power outlets................ 288

• Armrest ......................... 290

• Rear sunshade ............. 291

Interior lights list ................ 272

• Personal/interior light

main switch................... 273

• Trunk storage

• Personal/

extension ...................... 292

interior lights ................. 273

• Coat hooks.................... 293

• Assist grips ................... 293

Garage door opener.......... 294

Safety Connect ................. 301

Compass........................... 307

• Ambient lights ............... 274

5-3. Using the storage

features

List of storage features ..... 275

• Glove box...................... 276

• Console box.................. 276

• Cup holders .................. 277

• Auxiliary boxes.............. 278

Trunk features................... 283

260

5-1. Using the air conditioning system and defogger

Automatic air conditioning system

Air outlets and fan speed are automatically adjusted according

to the temperature setting.

Air conditioning controls

 Front control panel (type A)

 Front control panel (type B)

 Rear control panel (if equipped)

261

5-1. Using the air conditioning system and defogger

■ Adjusting the temperature setting

To adjust the temperature setting, touch

(driver’s side) to

(driver’s side) to decrease

increase the temperature and touch

the temperature.

The temperature for the driver’s, front passenger’s and rear seats (vehi-

cles with a rear control switch) can be adjusted separately when:

•

is pressed (the “SYNC” display disappears).

• The front passenger's side temperature control switch is touched

(the front passenger’s side temperature setting is shown).

• Vehicles with a rear control switch:

is pressed (

indicator is on and the rear passenger’s temperature setting is

shown).

• Vehicles with a rear control switch:

is turned (

indi-

cator is on and the rear passenger’s temperature setting is

shown).

5

The air conditioning system switches between individual and synchronized

modes each time

is touched.

Vehicles with a rear control switch: The rear passenger’s temperature set-

ting switches between individual and synchronized modes each time

is pressed.

262

■ Fan speed setting

5-1. Using the air conditioning system and defogger

To adjust the fan speed, touch

and slide your finger

toward “+” to increase the fan

speed or “-” to decrease the fan

speed.

The fan speed can also be

adjusted by touching “+” or “-” on

.

Touch

to turn the fan off.

■ Change the airflow mode

To change the airflow mode, press

.

The air outlets used are switched each time

 Type A  Type B

is pressed.

Air flows to the upper body.

Air flows to the feet.

1

2

3

4

Air flows to the upper body

and feet.

Air flows to the feet and the

windshield defogger operates.

■ Changing the rear seat temperature settings (vehicles with a

rear control switch)

→P. 263

263

5-1. Using the air conditioning system and defogger

Using the automatic air conditioning system

■ Using automatic operation

1

Touch

.

The air conditioning system begins to operate. Air outlets and fan speed

are automatically adjusted according to the temperature setting.

2

3

Adjust the temperature setting.

OFF

To stop the operation, touch

.

■ Changing the rear seat temperature settings (vehicles with a

rear control switch)

Turn

clockwise to increase the temperature and turn

counterclockwise to decrease the temperature.

■ Confirming automatic operation status

During automatic operation, the operation status of fan speed, air

outlet mode, outside/recirculated air mode and whether the A/C is

5

on or off can be confirmed on the display by touching

.

The display will return to its previous state after a few seconds.

■ Automatic mode indicator

If the fan speed setting or air flow modes are operated, the auto-

matic mode indicator goes off. However, automatic mode for func-

tions other than that operated is maintained.

264

5-1. Using the air conditioning system and defogger

Other functions

■ Switching between outside air and recirculated air modes

Press

.

The mode switches between

(outside air mode) and

(recir-

culated air mode) each time the button is pressed.

■ Defogging the windshield

Defoggers are used to defog the windshield and front side win-

dows.

Press

.

The dehumidification function operates and fan speed increases.

Set the outside/recirculated air mode button to the outside air mode if

the recirculated air mode is used. (It may switch automatically.)

To defog the windshield and the side windows early, turn the air flow and

temperature up.

To return to the previous mode, press

is defogged.

again when the windshield

■ Defogging the rear window and outside rear view mirrors

Defoggers are used to defog the rear window, and to remove rain-

drops, dew and frost from the outside rear view mirrors.

Press

.

The defoggers will automatically turn off after a period of time.

265

5-1. Using the air conditioning system and defogger

Air outlets

■ Location of air outlets

The air outlets and air volume

change according to the

selected airflow mode.

■ Adjusting the position of and opening and closing the air out-

lets

 Front center outlets

 Front side outlets

5

 Rear outlets

1

Direct air flow to the left or right, up or down.

Turn the knob to open or close the vent.

2

266

5-1. Using the air conditioning system and defogger

■Operation of the air conditioning system in Eco drive mode

In Eco drive mode, the air conditioning system is controlled as follows to pri-

oritize fuel efficiency:

●When the outside temperature exceeds 68°F (20°C), the air conditioning

system may switch to recirculated air mode automatically. This may also

reduce fuel consumption.

●It is possible to switch to outside air mode at any time by pressing

■Using automatic mode

.

Fan speed is adjusted automatically according to the temperature setting and

the ambient conditions.

Therefore, the fan may stop for a while until warm or cool air is ready to flow

immediately after

is touched.

■Fogging up of the windows

●The windows will easily fog up when the humidity in the vehicle is high.

Turning

on will dehumidify the air from the outlets and defog the wind-

shield effectively.

●If you turn

off, the windows may fog up more easily.

●The windows may fog up if the recirculated air mode is used.

■Outside/recirculated air mode

●When driving on dusty roads such as tunnels or in heavy traffic, set the out-

side/recirculated air mode to the recirculated air mode. This is effective in

preventing outside air from entering the vehicle interior. During cooling oper-

ation, setting the recirculated air mode will also cool the vehicle interior

effectively.

●Outside/recirculated air mode may automatically switch depending on the

temperature setting, outside temperature, pressure, engine coolant tem-

perature or inside temperature.

■When the outside temperature exceeds 75°F (24°C) and the air condition-

ing system is on (U.S.A. only)

●In order to reduce the air conditioning power consumption, the air condition-

ing system may switch to recirculated air mode automatically. This may also

reduce fuel consumption.

●Recirculated air mode is selected as a default mode when the engine switch

is turned to IGNITION ON mode.

●It is possible to switch to outside air mode at any time by pressing

.

■When the outside temperature falls to nearly 32°F (0°C)

The dehumidification function may not operate even when

is touched.

267

5-1. Using the air conditioning system and defogger

■Ventilation and air conditioning odors

●To let fresh air in, set the air conditioning system to the outside air mode.

●During use, various odors from inside and outside the vehicle may enter into

and accumulate in the air conditioning system. This may then cause odor to

be emitted from the vents.

●To reduce potential odors from occurring:

• This vehicle is equipped with a deodorizing charcoal air filter. This filter

should be inspected and replaced according to the maintenance sched-

ule. (Air conditioning filter: →P. 358)

• It is recommended that the air conditioning system be set to outside air

mode prior to turning the vehicle off.

• The start timing of the blower may be delayed for a short period of time

immediately after the air conditioning system is started in automatic

mode.

■Air conditioning filter

→P. 358

■Handling of the air conditioning panel

The operating section of the air conditioning panel uses touch switch sensors.

In the following cases, incorrect operation or non-response may occur.

●If the surface of the touch switch is dirty or has liquid attached to it, incorrect

operation or non-response may occur.

5

●If the surface of the touch switch receives electromagnetic waves, incorrect

operation or non-response may occur.

●If wearing gloves during operation, non-response may occur.

●If fingernails are used to operate the system, non-response may occur.

●If a touch pen is used to operate the system, non-response may occur.

●If the palm of your hand touches the surface of the touch switch during oper-

ation, incorrect operation may occur.

●If the palm of your hand touches the surface of the touch switch, incorrect

operation may occur.

●If operations are performed quickly, non-response may occur.

■Customization

Settings (e.g. air conditioning setting, touch switch sensitivity) can be

changed.

(Customizable features →P. 449)

268

5-1. Using the air conditioning system and defogger

WARNING

■To prevent the windshield from fogging up

●Do not use

during cool air operation in extremely humid weather.

The difference between the temperature of the outside air and that of the

windshield can cause the outer surface of the windshield to fog up, block-

ing your vision.

●Do not place anything on the instrument

panel which may cover the air outlets.

Otherwise, air flow may be obstructed,

preventing the windshield defoggers

from defogging.

■To prevent burns

Do not touch the rear view mirror surfaces when the outside rear view mirror

defoggers are on.

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the

engine is stopped.

269

5-1. Using the air conditioning system and defogger

Seat heaters^∗/seat ventilators^∗

The seat heaters warm the seats and the seat ventilators main-

tain good airflow by blowing air through the seats.

WARNING

●Care should be taken to prevent injury if anyone in the following categories

comes in contact with the seats when the heater is on:

• Babies, small children, the elderly, the sick and the physically chal-

lenged

• Persons with sensitive skin

• Persons who are fatigued

• Persons who have taken alcohol or drugs that induce sleep (sleeping

drugs, cold remedies, etc.)

●Observe the following precautions to prevent the minor burns or overheat-

ing

• Do not cover the seat with a blanket or cushion when using the seat

heater.

• Do not use seat heater more than necessary.

5

NOTICE

●Do not put heavy objects that have an uneven surface on the seat and do

not stick sharp objects (needles, nails, etc.) into the seat.

●To prevent battery discharge, do not use the functions when the engine is

not running.

∗: If equipped

270

■ Front seats

5-1. Using the air conditioning system and defogger

 Vehicles with ventilator

Press the knob to release it,

1

and turn the knob to the

desired temperature setting.

OFF

2

Press the knob to lock it

when not in use.

Ventilation

3

Heat

4

CTY57AX039

 Vehicles without ventilator

Press the knob to release it,

and turn the knob to the desired

temperature setting.

The further you turn the knob

clockwise, the warmer the seat

temperature becomes. Turn the

knob counterclockwise all the

way to turn the system off.

Press the knob again to lock it

when not in use.

271

5-1. Using the air conditioning system and defogger

■ Rear seats

ON/OFF

The indicator illuminates when

the seat heater is turned on.

■The seat heaters/seat ventilators can be used when

The engine switch is in IGNITION ON mode.

■Automatic operation of the seat ventilator for the passenger's seat

If a passenger leaves the passenger seat with the seat ventilator on, the seat

ventilator will automatically turn off after approximately 10 minutes. If the pas-

senger returns to the seat, it will automatically turn on again.

■Operation display illumination (if equipped)

1

Illuminates when the ventilator is

5

operating.

2

Illuminates when the front seat heater

is operating.

272

5-2. Using the interior lights

Interior lights list

Outer foot lights (if equipped)

Ambient lights (if equipped)

(→P. 274)

1

4

5

Rear personal/interior lights

(→P. 273)

2

Front door courtesy lights

Front personal/interior lights

3

(→P. 273)

273

5-2. Using the interior lights

Personal/interior light main switch

Turns the lights on/off

1

Turns the lights on/off linked to

2

door position

Personal/interior lights

■ Front

Turns the light on/off

5

■ Rear

Turns the light on/off

If the lights are turned on by the

personal/interior

light

main

switch, the lights cannot turn off

by pressing the switch.

274

5-2. Using the interior lights

Ambient lights (if equipped)

Each time the “MOOD” switch is

pressed, the brightness level

changes.

■Illuminated entry system

The lights automatically turn on/off according to engine switch mode, the

presence of the electronic key, whether the doors are locked/unlocked, and

whether the doors are opened/closed.

■To prevent battery discharge

If the personal/interior lights remain on when the engine switch is turned off,

the lights will go off automatically after 20 minutes.

■Customization

Setting (e.g. the time elapsed before lights turn off) can be changed.

(Customizable features: →P. 449)

NOTICE

To prevent battery discharge, do not leave the lights on longer than neces-

sary when the engine is not running.

275

5-3. Using the storage features

List of storage features

5

Auxiliary boxes

Glove box

(→P. 278)

(→P. 276)

Cup holders

Console box

(→P. 277)

(→P. 276)

1

2

3

4

WARNING

●Do not leave glasses, lighters or spray cans in the storage spaces, as this

may cause the following when cabin temperature becomes high:

• Glasses may be deformed by heat or cracked if they come into contact

with other stored items.

• Lighters or spray cans may explode. If they come into contact with other

stored items, the lighter may catch fire or the spray can may release

gas, causing a fire hazard.

●When driving or when the storage compartments are not in use, keep the

lids closed.

In the event of sudden braking or sudden swerving, an accident may occur

due to an occupant being struck by an open lid or the items stored inside.

276

5-3. Using the storage features

Glove box

Open (pull up the lever)

1

2

3

Lock with the mechanical key

Unlock with the mechanical key

The trunk opener main switch is located in the glove box. (→P. 104)

Console box

Lift the lid while pulling up the

lever to release the lock.

■When using the console box lid as an armrest

Slide the console box lid forward as

needed. Slide the lid forward while pulling

up the lever.

The lid can also be opened from the for-

wardmost position.

277

5-3. Using the storage features

■Tray in the console box

The tray slides forward/backward. To

remove the tray slide it forward and lift it.

Cup holders

 Front

 Rear (type A)

5

Pull down the armrest.

 Rear (type B)

Pull down the armrest and open

the lid.

WARNING

Do not place anything other than cups or aluminum cans in the cup holders.

Other items may be thrown out of the holders in the event of an accident or

sudden braking, causing injury. If possible, cover hot drinks to prevent

burns.

278

Auxiliary boxes

5-3. Using the storage features

 Type A

 Type B

Press in the button.

Push the lid.

 Type C

Opening

Push the tray forward until it locks.

Closing

Push the tray forward to release the lock and the tray will automatically

close.

279

5-3. Using the storage features

■When placing small items on top of the tray

The tray can be opened while small items

are placed on it.

An electronic device on the tray can be

recharged by running a charging cable

through the clearance of the tray and con-

necting it to the AUX/USB port or power

outlet underneath the tray.

5

280

5-3. Using the storage features

■When using wireless charger (if equipped)

A mobile device can be charged wirelessly on the tray.

Charging can only be performed with the engine switch in ACCESSORY or

IGNITION ON mode and only on mobile devices with the “ ” logo.

1

Push the tray forward until it locks and

press the wireless charger switch.

2

Push the tray forward to release the

lock to close the tray and place a mobile

device on the tray as shown in the illus-

tration.

An amber indicator is illuminated while

charging is in progress. When charging

is complete, a green indicator will also

be illuminated.

Some phones, cases or cover type

wireless chargers may not cause the

green indicator to illuminate even

though it is fully charged.

When placing the mobile device on the

wireless charging surface of the tray,

make sure that there are no objects in-

between the mobile device and the tray.

They may interfere with charging.

■If the wireless charger LED indicators flash

If the wireless charging surface of the tray becomes too hot, the LED indica-

tors will flash and charging is canceled. The LED indicators will be illuminated

if the surface of the tray cools down.

If the LED indicators flash even though the surface of the tray is not hot, the

wireless charger may be malfunctioning. Consult your Toyota dealer.

281

5-3. Using the storage features

■When charging of the wireless charger stops temporarily

If any of the following operations are performed with the electronic key pres-

ent, charging may stop temporarily. Charging will start again after a while.

●Locking/unlocking the doors by touching the door handle

●Opening/closing the doors

●Pressing the trunk opener switch

●Closing the trunk lid

●Starting the engine

●Locking the doors by pressing the lock button on the electronic key

●When the electronic key is out of the detection area

■Certification for the wireless charger

 For vehicles sold in the U.S.A.

This device complies with Part 18 of the FCC Rules.

Toyota Motor Sales, U.S.A., Inc.

19001 S. Western Avenue

Torrance, CA 90501

 For vehicles sold in Canada

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme à la norme NMB-001 du Canada.

5

WARNING

■Items unsuitable for storing (type B only)

Do not store items heavier than 0.4 lb. (0.2 kg).

Doing so may cause the auxiliary box to open and the items inside may fall

out, resulting in an accident.

282

5-3. Using the storage features

WARNING

■Caution regarding interference with electronic devices (vehicles with a

wireless charger)

●People with implantable cardiac pacemakers, cardiac resynchronization

therapy-pacemakers or implantable cardioverter defibrillators should main-

tain a reasonable distance between themselves and the wireless charger.

The radio waves may affect the operation of such devices.

●Before using the wireless charger, users of any electrical medical device

other than implantable cardiac pacemakers, cardiac resynchronization

therapy-pacemakers or implantable cardioverter defibrillators should con-

sult the manufacturer of the device for information about its operation

under the influence of radio waves. Radio waves could have unexpected

effects on the operation of such medical devices.

●To avoid interference with other electrical devices, turn the wireless char-

ger off by turning off the wireless charger switch.

■When using wireless charger

Avoid placing metal objects between the wireless charger and the mobile

device when charging is active. Doing so may cause metal objects to

become hot and could cause burns.

NOTICE

●To prevent damaging small items, when opening the tray while small items

are placed on it, make sure the items will not get caught.

●To prevent damaging the tray, do not pull down the tray to close it. Doing

so may damage the tray.

●When on a steep downward incline, the tray can be closed slowly. In this

case, the tray can be pulled down to close it.

However, make sure the lock has been released before doing so.

283

5-3. Using the storage features

Trunk features

Grocery bag hooks

5

Cargo net (if equipped)

284

5-3. Using the storage features

NOTICE

To prevent damage to the hooks, do not apply too much load to the hooks.

285

5-4. Other interior features

Other interior features

Sun visors

To set the visor in the forward

1

position, flip it down.

To set the visor in the side posi-

2

tion, flip down, unhook, and

swing it to the side.

To use the side extender, place

3

the visor in the side position,

then slide it backward.

Vanity mirrors

Open the cover to use.

The light turns on when the cover

is opened.

5

NOTICE

To prevent battery discharge, do not leave the vanity lights on for extended

periods while the engine is off.

286

5-4. Other interior features

Clock

The clock can be adjusted by pressing the buttons.

 Type A

 Type B

Adjusts the hours

1

2

Pressing and holding the button adjusts the hours forward quickly 1 hour at

a time.

Adjusts the minutes

Pressing and holding the button adjusts the minutes forward quickly by 1

minute at a time. If the button is pressed and held for 5 seconds or more,

the minutes move forward by 5 minutes at a time.

■The clock is displayed when

The engine switch is in ACCESSORY or IGNITION ON mode.

■When disconnecting and reconnecting battery terminals

 Type A

The time display will automatically be set to 12:00 AM.

 Type B

The time display will automatically be set to 12:00.

■Time display (Type B)

After pressing “H” or “M” to show the setting screen, press “H” and “M” at the

same time to change between the analog and digital displays.

287

5-4. Other interior features

Outside temperature display

The temperature display shows temperatures within the range of -40°F

(-40°C) to 122°F (50°C).

 Type A

 Type B

㧲

■The outside temperature is displayed when

The engine switch is in IGNITION ON mode.

■Display

In the following situations, the correct outside temperature may not be dis-

played, or the display may take longer than normal to change.

5

●When the vehicle is stopped, or moving at low speeds (less than 16 mph [25

km/h]).

●When the outside temperature has changed suddenly (at the entrance/exit

of a garage, tunnel, etc.)

■When “---°F” is displayed

The system may be malfunctioning. Take your vehicle to your Toyota dealer.

288

Power outlets

5-4. Other interior features

The power outlets can be used for 12 V accessories that run on less

than 10 A.

■ Console box

■ Instrument panel

 Type A

 Type B

289

5-4. Other interior features

■ Rear armrest (if equipped)

5

■The power outlets can be used when

The engine switch is in ACCESSORY or IGNITION ON mode.

NOTICE

●To avoid damaging the power outlets, close the power outlet lids when the

power outlets are not in use.

Foreign objects or liquids that enter the power outlets may cause a short

circuit.

●To prevent blown fuse, do not use an accessory that uses more than 12 V

10 A.

●To prevent battery discharge, do not use the power outlets longer than

necessary when the engine is off.

290

5-4. Other interior features

Armrest

Fold down the armrest for use.

NOTICE

To prevent damage to the armrest, do not apply too much load on the arm-

rest.

291

5-4. Other interior features

Rear sunshade (if equipped)

The rear sunshade can be raised and lowered by pressing the switch

shown below.

Extends/retracts the rear sun-

shade

■The rear sunshade can be used when

The engine switch is in IGNITION ON mode.

■Reverse operation feature

To ensure adequate rear visibility, the rear sunshade automatically lowers

when the shift lever is shifted to R.

5

However, the rear sunshade is raised again if either of the following occurs:

●The button is pressed again.

●The shift lever is shifted out of R, and the vehicle reaches a speed of 9 mph

(15 km/h).

If the engine is turned off when the rear sunshade has been lowered due to

the reverse operation feature, it will not be raised even when the engine is

turned on again and the vehicle reaches a speed of 9 mph (15 km/h). To raise

the sunshade again, press the button.

■Customization

Settings (e.g. time elapsed before the reverse operation feature activates)

can be changed.

(Customizable features: →P. 449)

WARNING

When the rear sunshade is being raised or lowered, do not place fingers or

other objects in the fastener section or in the opening. They may get caught,

causing injury.

292

5-4. Other interior features

NOTICE

To prevent battery discharge, do not operate the rear sunshade when the

engine is not running.

To ensure normal operation of the sunshade, observe the following precau-

tions.

●Do not place excessive load on the motor or other components.

●Do not place objects where they may hinder opening and closing opera-

tions.

●Do not attach items to the rear sunshade.

●Keep the opening clean and clear of obstructions.

●Do not operate the rear sunshade continuously for long periods of time.

Trunk storage extension

Long objects can be loaded into the vehicle by utilizing the trunk

space and rear seat area.

1

Fold down the armrest.

2

Push down the handle and

open the armrest door.

The armrest door can be locked

and

unlocked

using

the

mechanical key.

Lock

1

Unlock

2

WARNING

■When not in use

Ensure that the armrest door is closed.

In the event of sudden braking, items stored in the trunk may be thrown for-

ward into the cabin, resulting in injury.

293

5-4. Other interior features

Coat hooks

The coat hooks are provided with

the rear assist grips.

WARNING

Do not hang coat hangers or other hard or sharp objects on the hook. If the

SRS curtain shield airbags deploy, these items may become projectiles,

causing death or serious injury.

Assist grips

An assist grip installed on the ceil-

ing can be used to support your

body while sitting on the seat.

5

WARNING

Do not use the assist grip when getting in or out of the vehicle or rising from

your seat.

NOTICE

To prevent damage to the assist grip, do not hang any heavy object or put a

heavy load on the assist grip.

294

5-4. Other interior features

Garage door opener^∗

The garage door opener can be programmed to operate garage

doors, gates, entry doors, door locks, home lighting systems,

security systems, and other devices.



The garage door opener (HomeLink Universal Transceiver) is manu-



factured under license from HomeLink .

Programming the HomeLink^®(for U.S.A. owners)



The HomeLink compatible transceiver in your vehicle has 3 buttons

which can be programmed to operate 3 different devices. Refer to the

programming method below appropriate for the device.

Indicator light

1

Buttons

2

∗: If equipped

295

5-4. Other interior features



■ Programming the HomeLink

1

Point the remote control for

the device 1 to 3 in. (25 to 75

mm) from the HomeLink



control buttons.

Keep the indicator light on the

HomeLink^in view while pro-

gramming.

2

Press and hold one of the

HomeLink^®buttons and the

transmitter button. When the

HomeLink^®indicator light

changes from a slow to a

rapid flash, you can release

both buttons.

If the HomeLink^®indicator light

comes on but does not flash, or

flashes rapidly for 2 seconds

and remains lit, the HomeLink^®

button is already programmed.

Use the other buttons or follow

the “Reprogramming a Home-

Link^®button” instructions. (→P.

299)

5

296

5-4. Other interior features

3

Test the operation of the

HomeLink^®by pressing the

newly programmed button.

If programming a garage door

opener, check to see if the

garage door opens and closes.

If the garage door does not

operate, see if your garage

transmitter is of the Rolling

Code type. Press and hold the

programmed HomeLink^®button.

The garage door has the rolling

code feature if the indicator light

(on the HomeLink^®) flashes rap-

idly for 2 seconds and then

remains lit. If your transmitter is

the Rolling Code type, proceed

to the heading “Programming a

rolling code system”.

4

Repeat the steps above to program another device for each of

the remaining HomeLink buttons.



297

5-4. Other interior features

■ Programming a Rolling Code system (for U.S.A. owners)

If your device is Rolling Code equipped, follow the steps under the



heading “Programming the HomeLink ” before proceeding with the

steps listed below.

1

Locate the training button on the ceiling mounted garage door

opener motor. The exact location and color of the button may

vary by brand of garage door opener.

Refer to the operation manual supplied with the garage door opener for

the location of the training button.

2

Press the training button.

Following this step, you have 30 seconds in which to initiate step 3

below.



3

Press and hold the vehicle’s programmed HomeLink button for

2 seconds and release it. Repeat this step once again. The

garage door may open.

If the garage door opens, the programming process is complete. If the

door does not open, press and release the button a third time. This third

press and release will complete the programming process by opening

the garage door.

5

The ceiling mounted garage door opener motor should now recognize

the HomeLink^transceiver and operate the garage door.

4

Repeat the steps above to program another rolling code system

for any of the remaining HomeLink buttons.



298

5-4. Other interior features

■ Programming an entry gate (for U.S.A. owners)/Programming

all devices in the Canadian market

1

Place your transmitter 1 to 3 in. (25 to 75 mm) away from the sur-

face of the HomeLink .



Keep the indicator light on the HomeLink^in view while programming.



2

Press and hold the selected HomeLink button.

3

Repeatedly press and release (cycle) the device’s remote control

button for two seconds each until step 4 is completed.



4

When the indicator light on the HomeLink compatible trans-

ceiver starts to flash rapidly, release the buttons.



5

Test the operation of the HomeLink by pressing the newly pro-

grammed button. Check to see if the gate/device operates cor-

rectly.

6

Repeat the steps above to program another device for each of

the remaining HomeLink buttons.



■ Programming other devices

To program other devices such as home security systems, home

door locks or lighting, contact your authorized Toyota dealer for

assistance.

■ Reprogramming a button



The individual HomeLink buttons cannot be erased but can be

reprogrammed. To reprogram a button, follow the “Basic program-

ming” instructions.

299

5-4. Other interior features

Operating the HomeLink^®



Press the appropriate HomeLink button. The HomeLink indicator



light on the HomeLink transceiver should turn on.

The HomeLink^continues to send a signal for up to 20 seconds as long as

the button is pressed.

Reprogramming a HomeLink^®button

Press and hold the desired HomeLink^®button. After 20 seconds, the

HomeLink^®indicator light will start flashing slowly. Keep pressing the

HomeLink^®button and press and hold the transmitter button until the

HomeLink^®indicator light changes from a slow to a rapid flash.

Release the buttons.

Erasing the entire HomeLink^®memory (all three programs)

Press and hold down the 2 out-

side buttons for 10 seconds until

the indicator light flashes.

5

If you sell your vehicle, be sure to

erase the programs stored in the

HomeLink^memory.

300

5-4. Other interior features

■Before programming

●Install a new battery in the transmitter.

●The battery side of the transmitter must be pointed away from the Home-

Link^.

■Certification for the garage door opener

 For vehicles sold in the U.S.A.

FCC ID: NZLWZLHL4

NOTE:

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC WARNING:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

 For vehicles sold in Canada

NOTE:

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, includ-

ing interference that may cause undesired operation of the device.

■For additional programming assistance with your HomeLink^®Universal

Transceiver

Visit on the web at or call 1-800-355-3515.

WARNING

■When programming a garage door or other remote control device

The garage door may operate, so ensure people and objects are out of dan-

ger to prevent potential harm.

■Conforming to federal safety standards

Do not use the HomeLink^Compatible Transceiver with any garage door

opener or device that lacks safety stop and reverse features as required by

federal safety standards.

This includes any garage door that cannot detect an obstruction object. A

door or device without these features increases the risk of death or serious

injury.

301

5-4. Other interior features

Safety Connect^∗

Safety Connect is a subscription-based telematics service that

uses Global Positioning System (GPS) data and embedded cel-

lular technology to provide safety and security features to sub-

scribers. Safety Connect is supported by Toyota’s designated

response center, which operates 24 hours per day, 7 days per

week.

Safety Connect service is available by subscription on select,

telematics hardware-equipped vehicles.

By using the Safety Connect service, you are agreeing to be

bound by the Telematics Subscription Service Agreement and

its Terms and Conditions, as in effect and amended from time to

time, a current copy of which is available at . All use

of the Safety Connect service is subject to such then-applicable

Terms and Conditions.

5

■ System components

Microphone

1

LED light indicators

2

“SOS” button

3

∗: If equipped

302

■ Services

5-4. Other interior features

Subscribers have the following Safety Connect services available:

● Automatic Collision Notification*

Helps drivers receive necessary response from emergency ser-

vice providers. (→P. 304)

*: U.S. Patent No. 7,508,298 B2

● Stolen Vehicle Location

Helps drivers in the event of vehicle theft. (→P. 305)

● Emergency Assistance Button (SOS)

Connects drivers to response-center support. (→P. 305)

● Enhanced Roadside Assistance

Provides drivers various on-road assistance. (→P. 305)

■ Subscription

After you have signed the Telematics Subscription Service Agree-

ment and are enrolled, you can begin receiving services.

A variety of subscription terms is available for purchase. Contact

your Toyota dealer, call 1-800-331-4331, or push the “SOS” button

in your vehicle for further subscription details.

303

5-4. Other interior features

■Safety Connect Services Information

●Phone calls using the vehicles Bluetooth^®technology will not be possible

during Safety Connect.

●Safety Connect is available beginning Fall 2009 on select Toyota models.

Contact with the Safety Connect response center is dependent upon the

telematics device being in operative condition, cellular connection availabil-

ity, and GPS satellite signal reception, which can limit the ability to reach the

response center or receive emergency service support. Enrollment and

Telematics Subscription Service Agreement required. A variety of subscrip-

tion terms is available; charges vary by subscription term selected.

●Automatic Collision Notification, Emergency Assistance, Stolen Vehicle

Location, and Enhanced Roadside Assistance will function in the United

States, including Hawaii and Alaska, and in Canada. No Safety Connect

services will function outside of the United States in countries other than

Canada.

●Safety Connect services are not subject to section 255 of the Telecommuni-

cations Act and the device is not TTY compatible.

■Languages

The Safety Connect response center will offer support in multiple languages.

The Safety Connect system will offer voice prompts in English and Spanish.

Please indicate your language of choice when enrolling.

5

■When contacting the response center

You may be unable to contact the response center if the network is busy.

304

5-4. Other interior features

Safety Connect LED light Indicators

When the engine switch is turned to IGNITION ON mode, the red indi-

cator light comes on for 2 seconds then turns off. Afterward, the green

indicator light comes on, indicating that the service is active.

The following indicator light patterns indicate specific system usage

conditions:

● Green indicator light on = Active service

● Green indicator light flashing = Safety Connect call in process

● Red indicator light (except at vehicle start-up) = System malfunction

(contact your Toyota dealer)

● No indicator light (off) = Safety Connect service not active

Safety Connect services

■ Automatic Collision Notification

In case of either airbag deployment or severe rear-end collision, the

system is designed to automatically call the response center. The

responding agent receives the vehicle’s location and attempts to

speak with the vehicle occupants to assess the level of emergency.

If the occupants are unable to communicate, the agent automati-

cally treats the call as an emergency, contacts the nearest emer-

gency services provider to describe the situation, and requests that

assistance be sent to the location.

305

5-4. Other interior features

■ Stolen Vehicle Location

If your vehicle is stolen, Safety Connect can work with local author-

ities to assist them in locating and recovering the vehicle. After filing

a police report, call the Safety Connect response center at 1-800-

331-4331 and follow the prompts for Safety Connect to initiate this

service.

In addition to assisting law enforcement with recovery of a stolen

vehicle, Safety-Connect-equipped vehicle location data may, under

certain circumstances, be shared with third parties to locate your

vehicle. Further information is available at To.

■ Emergency Assistance Button (“SOS”)

In the event of an emergency on the road, push the “SOS” button to

reach the Safety Connect response center. The answering agent

will determine your vehicle’s location, assess the emergency, and

dispatch the necessary assistance required.

If you accidentally press the “SOS” button, tell the response-center

agent that you are not experiencing an emergency.

5

■ Enhanced Roadside Assistance

Enhanced Roadside Assistance adds GPS data to the already

included warranty-based Toyota roadside service.

Subscribers can press the “SOS” button to reach a Safety Connect

response-center agent, who can help with a wide range of needs,

such as: towing, flat tire, fuel delivery, etc. For a description of the

Enhanced Roadside Assistance services and their limitations,

please see the Safety Connect Terms and Conditions, which are

available at To.

306

5-4. Other interior features

Safety information for Safety Connect

Important! Read this information before using Safety Connect.

■ Exposure to radio frequency signals

The Safety Connect system installed in your vehicle is a low-power

radio transmitter and receiver. It receives and also sends out radio

frequency (RF) signals.

In August 1996, the Federal Communications Commission (FCC)

adopted RF exposure guidelines with safety levels for mobile wire-

less phones. Those guidelines are consistent with the safety stan-

dards previously set by the following U.S. and international

standards bodies.

● ANSI (American National Standards Institute) C95.1 [1992]

● NCRP (National Council on Radiation Protection and Measure-

ment) Report 86 [1986]

● ICNIRP (International Commission on Non-Ionizing Radiation

Protection) [1996]

Those standards were based on comprehensive and periodic eval-

uations of the relevant scientific literature. Over 120 scientists, engi-

neers, and physicians from universities, and government health

agencies and industries reviewed the available body of research to

develop the ANSI Standard (C95.1).

The design of Safety Connect complies with the FCC guidelines in

addition to those standards.

■Certification for Safety Connect

FCC ID: O6Y-CDMRF101

FCC ID: XOECDMRF101B

FCC ID: N7NGTM2

NOTE:

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interfer-

ence, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC WARNING:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

307

5-4. Other interior features

Compass^∗

The compass on the inside rear view mirror indicates the direc-

tion in which the vehicle is heading.

■ Operation

To turn the compass on or off,

press the switch for more than 3

seconds.

■ Displays and directions

Display

N

Direction

North

5

NE

E

Northeast

East

SE

S

Southeast

South

SW

W

Southwest

West

NW

Northwest

∗: If equipped

308

5-4. Other interior features

Calibrating the compass

Samoa: 5 Guam: 8 Saipan: 8

The direction display deviates from the true direction determined by

the earth’s magnetic field. The amount of deviation varies according to

the geographic position of the vehicle.

If you cross over a map boundary shown in illustration, the compass will

deviate.

To obtain higher precision or perfect calibration, refer to the following.

■ Deviation calibration

1

Stop the vehicle.

2

Press and hold the switch.

A number (1 to 15) appears

on the compass display.

3

Referring to the map above, press the switch to select the num-

ber of the zone you are in.

If the direction is displayed several seconds after adjustment, the cali-

bration is complete.

309

5-4. Other interior features

■ Circling calibration

When “C” appears on the dis-

play, drive the vehicle at 5 mph

(8 km/h) or less in a circle until a

direction is displayed.

If there is not enough space to

drive in a circle, drive around the

block until the direction is dis-

played.

■Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions:

●The vehicle is stopped immediately after turning.

●The vehicle is on an inclined surface.

●The vehicle is in a place where the earth’s magnetic field is subject to inter-

ference by artificial magnetic fields (underground car park/parking lot, under

a steel tower, between buildings, roof car park/parking lot, near an intersec-

tion, near a large vehicle, etc.).

5

●The vehicle has become magnetized.

(There is a magnet or metal object near the inside rear view mirror.)

●The battery has been disconnected.

●A door is open.

WARNING

■While driving

Do not adjust the display.

Be sure to adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Be sure to secure a wide space, and watch out for people and vehicles in

the neighborhood. Do not violate any local traffic rules while performing cir-

cling calibration.

310

5-4. Other interior features

NOTICE

■To avoid the compass malfunctions

Do not place magnets or any metal objects near the inside rear view mirror.

Doing this may cause a malfunction of the compass sensor.

■To ensure normal operation of the compass

●Do not perform circling calibration of the compass in a place where the

earth’s magnetic field is subject to interference by artificial magnetic fields.

●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

Interior features for Your Toyota Avalon 4 Door Fourth Generation (2013-2018)

Related Topics

Popular Owner Manuals

Latest Owner Manuals