Get Interior features -> Other interior features Guide for Toyota Avalon 4 Door Fourth Generation (2013-2018)

285

5-4. Other interior features

Other interior features

Sun visors

To set the visor in the forward

1

position, flip it down.

To set the visor in the side posi-

2

tion, flip down, unhook, and

swing it to the side.

To use the side extender, place

3

the visor in the side position,

then slide it backward.

Vanity mirrors

Open the cover to use.

The light turns on when the cover

is opened.

5

NOTICE

To prevent battery discharge, do not leave the vanity lights on for extended

periods while the engine is off.

286

5-4. Other interior features

Clock

The clock can be adjusted by pressing the buttons.

 Type A

 Type B

Adjusts the hours

1

2

Pressing and holding the button adjusts the hours forward quickly 1 hour at

a time.

Adjusts the minutes

Pressing and holding the button adjusts the minutes forward quickly by 1

minute at a time. If the button is pressed and held for 5 seconds or more,

the minutes move forward by 5 minutes at a time.

■The clock is displayed when

The engine switch is in ACCESSORY or IGNITION ON mode.

■When disconnecting and reconnecting battery terminals

 Type A

The time display will automatically be set to 12:00 AM.

 Type B

The time display will automatically be set to 12:00.

■Time display (Type B)

After pressing “H” or “M” to show the setting screen, press “H” and “M” at the

same time to change between the analog and digital displays.

287

5-4. Other interior features

Outside temperature display

The temperature display shows temperatures within the range of -40°F

(-40°C) to 122°F (50°C).

 Type A

 Type B

㧲

■The outside temperature is displayed when

The engine switch is in IGNITION ON mode.

■Display

In the following situations, the correct outside temperature may not be dis-

played, or the display may take longer than normal to change.

5

●When the vehicle is stopped, or moving at low speeds (less than 16 mph [25

km/h]).

●When the outside temperature has changed suddenly (at the entrance/exit

of a garage, tunnel, etc.)

■When “---°F” is displayed

The system may be malfunctioning. Take your vehicle to your Toyota dealer.

288

Power outlets

5-4. Other interior features

The power outlets can be used for 12 V accessories that run on less

than 10 A.

■ Console box

■ Instrument panel

 Type A

 Type B

289

5-4. Other interior features

■ Rear armrest (if equipped)

5

■The power outlets can be used when

The engine switch is in ACCESSORY or IGNITION ON mode.

NOTICE

●To avoid damaging the power outlets, close the power outlet lids when the

power outlets are not in use.

Foreign objects or liquids that enter the power outlets may cause a short

circuit.

●To prevent blown fuse, do not use an accessory that uses more than 12 V

10 A.

●To prevent battery discharge, do not use the power outlets longer than

necessary when the engine is off.

290

5-4. Other interior features

Armrest

Fold down the armrest for use.

NOTICE

To prevent damage to the armrest, do not apply too much load on the arm-

rest.

291

5-4. Other interior features

Rear sunshade (if equipped)

The rear sunshade can be raised and lowered by pressing the switch

shown below.

Extends/retracts the rear sun-

shade

■The rear sunshade can be used when

The engine switch is in IGNITION ON mode.

■Reverse operation feature

To ensure adequate rear visibility, the rear sunshade automatically lowers

when the shift lever is shifted to R.

5

However, the rear sunshade is raised again if either of the following occurs:

●The button is pressed again.

●The shift lever is shifted out of R, and the vehicle reaches a speed of 9 mph

(15 km/h).

If the engine is turned off when the rear sunshade has been lowered due to

the reverse operation feature, it will not be raised even when the engine is

turned on again and the vehicle reaches a speed of 9 mph (15 km/h). To raise

the sunshade again, press the button.

■Customization

Settings (e.g. time elapsed before the reverse operation feature activates)

can be changed.

(Customizable features: →P. 449)

WARNING

When the rear sunshade is being raised or lowered, do not place fingers or

other objects in the fastener section or in the opening. They may get caught,

causing injury.

292

5-4. Other interior features

NOTICE

To prevent battery discharge, do not operate the rear sunshade when the

engine is not running.

To ensure normal operation of the sunshade, observe the following precau-

tions.

●Do not place excessive load on the motor or other components.

●Do not place objects where they may hinder opening and closing opera-

tions.

●Do not attach items to the rear sunshade.

●Keep the opening clean and clear of obstructions.

●Do not operate the rear sunshade continuously for long periods of time.

Trunk storage extension

Long objects can be loaded into the vehicle by utilizing the trunk

space and rear seat area.

1

Fold down the armrest.

2

Push down the handle and

open the armrest door.

The armrest door can be locked

and

unlocked

using

the

mechanical key.

Lock

1

Unlock

2

WARNING

■When not in use

Ensure that the armrest door is closed.

In the event of sudden braking, items stored in the trunk may be thrown for-

ward into the cabin, resulting in injury.

293

5-4. Other interior features

Coat hooks

The coat hooks are provided with

the rear assist grips.

WARNING

Do not hang coat hangers or other hard or sharp objects on the hook. If the

SRS curtain shield airbags deploy, these items may become projectiles,

causing death or serious injury.

Assist grips

An assist grip installed on the ceil-

ing can be used to support your

body while sitting on the seat.

5

WARNING

Do not use the assist grip when getting in or out of the vehicle or rising from

your seat.

NOTICE

To prevent damage to the assist grip, do not hang any heavy object or put a

heavy load on the assist grip.

294

5-4. Other interior features

Garage door opener^∗

The garage door opener can be programmed to operate garage

doors, gates, entry doors, door locks, home lighting systems,

security systems, and other devices.



The garage door opener (HomeLink Universal Transceiver) is manu-



factured under license from HomeLink .

Programming the HomeLink^®(for U.S.A. owners)



The HomeLink compatible transceiver in your vehicle has 3 buttons

which can be programmed to operate 3 different devices. Refer to the

programming method below appropriate for the device.

Indicator light

1

Buttons

2

∗: If equipped

295

5-4. Other interior features



■ Programming the HomeLink

1

Point the remote control for

the device 1 to 3 in. (25 to 75

mm) from the HomeLink



control buttons.

Keep the indicator light on the

HomeLink^in view while pro-

gramming.

2

Press and hold one of the

HomeLink^®buttons and the

transmitter button. When the

HomeLink^®indicator light

changes from a slow to a

rapid flash, you can release

both buttons.

If the HomeLink^®indicator light

comes on but does not flash, or

flashes rapidly for 2 seconds

and remains lit, the HomeLink^®

button is already programmed.

Use the other buttons or follow

the “Reprogramming a Home-

Link^®button” instructions. (→P.

299)

5

296

5-4. Other interior features

3

Test the operation of the

HomeLink^®by pressing the

newly programmed button.

If programming a garage door

opener, check to see if the

garage door opens and closes.

If the garage door does not

operate, see if your garage

transmitter is of the Rolling

Code type. Press and hold the

programmed HomeLink^®button.

The garage door has the rolling

code feature if the indicator light

(on the HomeLink^®) flashes rap-

idly for 2 seconds and then

remains lit. If your transmitter is

the Rolling Code type, proceed

to the heading “Programming a

rolling code system”.

4

Repeat the steps above to program another device for each of

the remaining HomeLink buttons.



297

5-4. Other interior features

■ Programming a Rolling Code system (for U.S.A. owners)

If your device is Rolling Code equipped, follow the steps under the



heading “Programming the HomeLink ” before proceeding with the

steps listed below.

1

Locate the training button on the ceiling mounted garage door

opener motor. The exact location and color of the button may

vary by brand of garage door opener.

Refer to the operation manual supplied with the garage door opener for

the location of the training button.

2

Press the training button.

Following this step, you have 30 seconds in which to initiate step 3

below.



3

Press and hold the vehicle’s programmed HomeLink button for

2 seconds and release it. Repeat this step once again. The

garage door may open.

If the garage door opens, the programming process is complete. If the

door does not open, press and release the button a third time. This third

press and release will complete the programming process by opening

the garage door.

5

The ceiling mounted garage door opener motor should now recognize

the HomeLink^transceiver and operate the garage door.

4

Repeat the steps above to program another rolling code system

for any of the remaining HomeLink buttons.



298

5-4. Other interior features

■ Programming an entry gate (for U.S.A. owners)/Programming

all devices in the Canadian market

1

Place your transmitter 1 to 3 in. (25 to 75 mm) away from the sur-

face of the HomeLink .



Keep the indicator light on the HomeLink^in view while programming.



2

Press and hold the selected HomeLink button.

3

Repeatedly press and release (cycle) the device’s remote control

button for two seconds each until step 4 is completed.



4

When the indicator light on the HomeLink compatible trans-

ceiver starts to flash rapidly, release the buttons.



5

Test the operation of the HomeLink by pressing the newly pro-

grammed button. Check to see if the gate/device operates cor-

rectly.

6

Repeat the steps above to program another device for each of

the remaining HomeLink buttons.



■ Programming other devices

To program other devices such as home security systems, home

door locks or lighting, contact your authorized Toyota dealer for

assistance.

■ Reprogramming a button



The individual HomeLink buttons cannot be erased but can be

reprogrammed. To reprogram a button, follow the “Basic program-

ming” instructions.

299

5-4. Other interior features

Operating the HomeLink^®



Press the appropriate HomeLink button. The HomeLink indicator



light on the HomeLink transceiver should turn on.

The HomeLink^continues to send a signal for up to 20 seconds as long as

the button is pressed.

Reprogramming a HomeLink^®button

Press and hold the desired HomeLink^®button. After 20 seconds, the

HomeLink^®indicator light will start flashing slowly. Keep pressing the

HomeLink^®button and press and hold the transmitter button until the

HomeLink^®indicator light changes from a slow to a rapid flash.

Release the buttons.

Erasing the entire HomeLink^®memory (all three programs)

Press and hold down the 2 out-

side buttons for 10 seconds until

the indicator light flashes.

5

If you sell your vehicle, be sure to

erase the programs stored in the

HomeLink^memory.

300

5-4. Other interior features

■Before programming

●Install a new battery in the transmitter.

●The battery side of the transmitter must be pointed away from the Home-

Link^.

■Certification for the garage door opener

 For vehicles sold in the U.S.A.

FCC ID: NZLWZLHL4

NOTE:

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC WARNING:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

 For vehicles sold in Canada

NOTE:

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, includ-

ing interference that may cause undesired operation of the device.

■For additional programming assistance with your HomeLink^®Universal

Transceiver

Visit on the web at or call 1-800-355-3515.

WARNING

■When programming a garage door or other remote control device

The garage door may operate, so ensure people and objects are out of dan-

ger to prevent potential harm.

■Conforming to federal safety standards

Do not use the HomeLink^Compatible Transceiver with any garage door

opener or device that lacks safety stop and reverse features as required by

federal safety standards.

This includes any garage door that cannot detect an obstruction object. A

door or device without these features increases the risk of death or serious

injury.

301

5-4. Other interior features

Safety Connect^∗

Safety Connect is a subscription-based telematics service that

uses Global Positioning System (GPS) data and embedded cel-

lular technology to provide safety and security features to sub-

scribers. Safety Connect is supported by Toyota’s designated

response center, which operates 24 hours per day, 7 days per

week.

Safety Connect service is available by subscription on select,

telematics hardware-equipped vehicles.

By using the Safety Connect service, you are agreeing to be

bound by the Telematics Subscription Service Agreement and

its Terms and Conditions, as in effect and amended from time to

time, a current copy of which is available at . All use

of the Safety Connect service is subject to such then-applicable

Terms and Conditions.

5

■ System components

Microphone

1

LED light indicators

2

“SOS” button

3

∗: If equipped

302

■ Services

5-4. Other interior features

Subscribers have the following Safety Connect services available:

● Automatic Collision Notification*

Helps drivers receive necessary response from emergency ser-

vice providers. (→P. 304)

*: U.S. Patent No. 7,508,298 B2

● Stolen Vehicle Location

Helps drivers in the event of vehicle theft. (→P. 305)

● Emergency Assistance Button (SOS)

Connects drivers to response-center support. (→P. 305)

● Enhanced Roadside Assistance

Provides drivers various on-road assistance. (→P. 305)

■ Subscription

After you have signed the Telematics Subscription Service Agree-

ment and are enrolled, you can begin receiving services.

A variety of subscription terms is available for purchase. Contact

your Toyota dealer, call 1-800-331-4331, or push the “SOS” button

in your vehicle for further subscription details.

303

5-4. Other interior features

■Safety Connect Services Information

●Phone calls using the vehicles Bluetooth^®technology will not be possible

during Safety Connect.

●Safety Connect is available beginning Fall 2009 on select Toyota models.

Contact with the Safety Connect response center is dependent upon the

telematics device being in operative condition, cellular connection availabil-

ity, and GPS satellite signal reception, which can limit the ability to reach the

response center or receive emergency service support. Enrollment and

Telematics Subscription Service Agreement required. A variety of subscrip-

tion terms is available; charges vary by subscription term selected.

●Automatic Collision Notification, Emergency Assistance, Stolen Vehicle

Location, and Enhanced Roadside Assistance will function in the United

States, including Hawaii and Alaska, and in Canada. No Safety Connect

services will function outside of the United States in countries other than

Canada.

●Safety Connect services are not subject to section 255 of the Telecommuni-

cations Act and the device is not TTY compatible.

■Languages

The Safety Connect response center will offer support in multiple languages.

The Safety Connect system will offer voice prompts in English and Spanish.

Please indicate your language of choice when enrolling.

5

■When contacting the response center

You may be unable to contact the response center if the network is busy.

304

5-4. Other interior features

Safety Connect LED light Indicators

When the engine switch is turned to IGNITION ON mode, the red indi-

cator light comes on for 2 seconds then turns off. Afterward, the green

indicator light comes on, indicating that the service is active.

The following indicator light patterns indicate specific system usage

conditions:

● Green indicator light on = Active service

● Green indicator light flashing = Safety Connect call in process

● Red indicator light (except at vehicle start-up) = System malfunction

(contact your Toyota dealer)

● No indicator light (off) = Safety Connect service not active

Safety Connect services

■ Automatic Collision Notification

In case of either airbag deployment or severe rear-end collision, the

system is designed to automatically call the response center. The

responding agent receives the vehicle’s location and attempts to

speak with the vehicle occupants to assess the level of emergency.

If the occupants are unable to communicate, the agent automati-

cally treats the call as an emergency, contacts the nearest emer-

gency services provider to describe the situation, and requests that

assistance be sent to the location.

305

5-4. Other interior features

■ Stolen Vehicle Location

If your vehicle is stolen, Safety Connect can work with local author-

ities to assist them in locating and recovering the vehicle. After filing

a police report, call the Safety Connect response center at 1-800-

331-4331 and follow the prompts for Safety Connect to initiate this

service.

In addition to assisting law enforcement with recovery of a stolen

vehicle, Safety-Connect-equipped vehicle location data may, under

certain circumstances, be shared with third parties to locate your

vehicle. Further information is available at To.

■ Emergency Assistance Button (“SOS”)

In the event of an emergency on the road, push the “SOS” button to

reach the Safety Connect response center. The answering agent

will determine your vehicle’s location, assess the emergency, and

dispatch the necessary assistance required.

If you accidentally press the “SOS” button, tell the response-center

agent that you are not experiencing an emergency.

5

■ Enhanced Roadside Assistance

Enhanced Roadside Assistance adds GPS data to the already

included warranty-based Toyota roadside service.

Subscribers can press the “SOS” button to reach a Safety Connect

response-center agent, who can help with a wide range of needs,

such as: towing, flat tire, fuel delivery, etc. For a description of the

Enhanced Roadside Assistance services and their limitations,

please see the Safety Connect Terms and Conditions, which are

available at To.

306

5-4. Other interior features

Safety information for Safety Connect

Important! Read this information before using Safety Connect.

■ Exposure to radio frequency signals

The Safety Connect system installed in your vehicle is a low-power

radio transmitter and receiver. It receives and also sends out radio

frequency (RF) signals.

In August 1996, the Federal Communications Commission (FCC)

adopted RF exposure guidelines with safety levels for mobile wire-

less phones. Those guidelines are consistent with the safety stan-

dards previously set by the following U.S. and international

standards bodies.

● ANSI (American National Standards Institute) C95.1 [1992]

● NCRP (National Council on Radiation Protection and Measure-

ment) Report 86 [1986]

● ICNIRP (International Commission on Non-Ionizing Radiation

Protection) [1996]

Those standards were based on comprehensive and periodic eval-

uations of the relevant scientific literature. Over 120 scientists, engi-

neers, and physicians from universities, and government health

agencies and industries reviewed the available body of research to

develop the ANSI Standard (C95.1).

The design of Safety Connect complies with the FCC guidelines in

addition to those standards.

■Certification for Safety Connect

FCC ID: O6Y-CDMRF101

FCC ID: XOECDMRF101B

FCC ID: N7NGTM2

NOTE:

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interfer-

ence, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC WARNING:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

307

5-4. Other interior features

Compass^∗

The compass on the inside rear view mirror indicates the direc-

tion in which the vehicle is heading.

■ Operation

To turn the compass on or off,

press the switch for more than 3

seconds.

■ Displays and directions

Display

N

Direction

North

5

NE

E

Northeast

East

SE

S

Southeast

South

SW

W

Southwest

West

NW

Northwest

∗: If equipped

308

5-4. Other interior features

Calibrating the compass

Samoa: 5 Guam: 8 Saipan: 8

The direction display deviates from the true direction determined by

the earth’s magnetic field. The amount of deviation varies according to

the geographic position of the vehicle.

If you cross over a map boundary shown in illustration, the compass will

deviate.

To obtain higher precision or perfect calibration, refer to the following.

■ Deviation calibration

1

Stop the vehicle.

2

Press and hold the switch.

A number (1 to 15) appears

on the compass display.

3

Referring to the map above, press the switch to select the num-

ber of the zone you are in.

If the direction is displayed several seconds after adjustment, the cali-

bration is complete.

309

5-4. Other interior features

■ Circling calibration

When “C” appears on the dis-

play, drive the vehicle at 5 mph

(8 km/h) or less in a circle until a

direction is displayed.

If there is not enough space to

drive in a circle, drive around the

block until the direction is dis-

played.

■Conditions unfavorable to correct operation

The compass may not show the correct direction in the following conditions:

●The vehicle is stopped immediately after turning.

●The vehicle is on an inclined surface.

●The vehicle is in a place where the earth’s magnetic field is subject to inter-

ference by artificial magnetic fields (underground car park/parking lot, under

a steel tower, between buildings, roof car park/parking lot, near an intersec-

tion, near a large vehicle, etc.).

5

●The vehicle has become magnetized.

(There is a magnet or metal object near the inside rear view mirror.)

●The battery has been disconnected.

●A door is open.

WARNING

■While driving

Do not adjust the display.

Be sure to adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Be sure to secure a wide space, and watch out for people and vehicles in

the neighborhood. Do not violate any local traffic rules while performing cir-

cling calibration.

310

5-4. Other interior features

NOTICE

■To avoid the compass malfunctions

Do not place magnets or any metal objects near the inside rear view mirror.

Doing this may cause a malfunction of the compass sensor.

■To ensure normal operation of the compass

●Do not perform circling calibration of the compass in a place where the

earth’s magnetic field is subject to interference by artificial magnetic fields.

●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

Interior features -> Other interior features for Your Toyota Avalon 4 Door Fourth Generation (2013-2018)

Related Topics

Popular Owner Manuals

Latest Owner Manuals