Get Instruments, indicators and service lights Guide for Toyota Avensis 4 Door Second Generation (2004-2009)

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

151

Chapter 1–6

OPERATION OF INSTRUMENTS AND CONTROLS

ELEMENTS

Instruments, indicators and service lights

• Fuel gauge. .

.

. . . . . . . .

.

. . . . . . . . . . . . . . .

.

. . . . . . . .

. 152

. 153

• Engine coolant temperature gauge. . • Tachometer.

.

. . . . . . . .

.

. . . . . . . . . . . . . . .

• Display of the total and two partial odometers and control of the

.

. . . . . . . .

. 153

. 154

. 157

. 167

lighting of the instrument panel. .

. . . . . . . . . . . . .

. . . . . . . . . . . . . . .

. .

. . . . . . . .

• Oil maintenance management

. . . .

.

system. • Combined

display. . • Service lights and warning buzzers. .

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

152

Coolant temperature indicator

engine fluids

Fuel gauge

Low fuel

warning

light

With the ignition switch on, the gauge shows the

approximate amount of fuel remaining in the tank.

The gauge shows the engine coolant temperature

when the ignition switch is on.

Engine operating temperature will vary with changes in

weather and engine load.

Almost full ÿ Hand at "1/1"

Almost Empty ÿ Hand at "R"

If the needle moves into the red area, your engine is too

hot. If the vehicle overheats, stop the vehicle and allow

the engine to cool.

It is good practice to leave the tank at least 1/4 full.

The hand moves when braking, accelerating or cornering.

This is caused by the movement of fuel in the tank.

Your vehicle can overheat during difficult operating

conditions such as:

If the gauge reaches the "R" position or the low fuel

warning light comes on, fill up the fuel tank as soon as

possible.

• Riding up a long climb in hot weather.

• Slowing down or stopping after driving at

high speed.

On a slope or in corners, the fuel gauge needle may

fluctuate due to the movement of fuel in the tank, or the

low fuel warning light may come on earlier than normal.

• The engine runs for a long time at idling

speed with the air conditioning on, e.g.

when driving.

• Towing a trailer.

For some models ÿ

If the tank is completely empty, the fault light will come

on. Fill the fuel tank immediately.

NOTICE

u Do not remove the thermostat from the

engine cooling system, as this may cause

the engine to overheat. The thermostat is

designed to control the flow of coolant to

keep the engine temperature within a

specified operating range.

The light goes out after driving for a while. If the warning

light does not go out, contact any authorized Toyota

dealer or service center, or another properly qualified

and equipped professional, as soon as possible.

u Do not continue driving with an overheated

engine. See "When the vehicle overheats"

on page 327 in Chapter 4.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

153

Display of the total and two

partial odometers and control

of the lighting of the instrument panel

Tachometer

Petrol engine

No combined display

Diesel engine

The tachometer shows engine revolutions

With combined display

This display shows the following information.

in thousands per minute. Use the tachometer

readings to correctly shift gears while

driving and to prevent the engine from

jerking and over-revving.

1. Total odometer ÿ Indicates the total distance

traveled by the vehicle.

2. Two partial odometers ÿ They show,

independently of each other, two different

distances that the vehicle has traveled since

the last reset of each odometer.

Driving at high engine speeds causes increased

engine wear and increases fuel consumption.

Remember that, in most cases, lower engine

speeds result in lower fuel consumption.

You can use one counter to calculate fuel

consumption, the other to measure the

distance of an individual trip. All odometer

readings will be cleared when the power

source is disconnected.

NOTICE

Do not let the pointer reach the red field.

This can cause serious engine damage.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

154

Oil maintenance management system

(diesel engines, without combined display)

3. Instrument panel lighting control display

(when the headlight switch is on)

The Oil Maintenance Management System

(OMMS) is designed to inform you via a

warning light when it is time to change the

oil and oil filter.

ÿ Shows the brightness of the instrument panel

lighting. The higher the height of the column, the

brighter the illumination of the instrument panel.

4. Reset button for sub-kilometer counters/

instrument panel lighting control ÿ Resets

both sub-kilometer counters, changes the

display and adjusts the brightness of the

instrument panel lighting.

CHANGING ENGINE OIL AND OIL-

JOHN FILTER

Change the engine oil and oil filter in any of the

following cases:

• When the engine oil change light is on

To change the display view, quickly press and

release the button. Each time the button is pressed,

the display changes from the total counter to sub-

counter A, sub-counter B, the instrument panel

lighting control display and then back to the total

counter.

• When the system is being

repaired. • When the engine oil change light

does not illuminate even if 2 years have

passed since the oil change.

• When the engine oil change indicator light

does not illuminate even though it has been

more than 30000 km since the oil change.

To reset sub-counter A, switch to this counter

display and press and hold the button until

the counter reading is reset to zero. Use the

same procedure to reset counter B.

The lighting interval may vary according to

driving conditions.

To adjust the brightness of the instrument

panel illumination, switch to the instrument

panel illumination brightness setting view

and press and hold the button until the

desired brightness is reached.

Because the condition of the engine oil

deteriorates over time, there are times when

the engine oil must be changed before the

engine oil change light comes on. In these

cases, replace the engine oil and oil filter

according to the maintenance schedule

(Engine oil maintenance intervals - see

"Toyota Service Book" or "Toyota Warranty

Book".)

5. Reset button for sub-kilometer counters –

Resets both sub-kilometer counters,

changes the display.

To change the display view, quickly press and

release the button. Each time the button is pressed,

NOTICE

the display changes from the total counter to sub-

counter A, sub-counter B and then back to the total

counter.

Reset the system after changing the

engine oil and oil filter. (System reset

procedure - see "SYSTEM RESET" on page

155 in this chapter.)

To reset sub-counter A, switch to this counter

display and press and hold the button until

the counter reading is reset to zero. Use the

same procedure to reset counter B.

If you do not reset the system, it cannot

inform you of the correct time to change

the engine oil and oil filter.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

155

If any of the following situations occur, the system

may not operate normally. Have the vehicle inspected

by any authorized Toyota dealer or workshop, or by

another properly qualified and equipped professional.

• When the ignition key is turned to the "ON" position, the

indicator light does not light up.

• The indicator light flashes.

• After changing the engine oil and oil filter,

even if the system has been reset, the

warning light does not go out or comes on soon

again.

ENGINE REPLACEMENT LIGHT

OILS

SYSTEM RESET

This light comes on when you turn the ignition key to the

"ON" position. It turns off after about 5 seconds. This

means that the system is working normally.

The system must be reset after changing the engine oil.

Perform a system reset as follows:

If this light comes on while driving, replace the engine

1. Turn the ignition key to the "ACC" or "LOCK" position

with the odometer displayed. (Details - see "Total and

two trip meter display and instrument panel lighting

control" on page 153 in this chapter.)

oil and oil filter at the earliest opportunity using the

appropriate replacement parts. For more information

on oil grade and viscosity - see "Checking the engine

oil level" on page 372 in chapter 7ÿ2.

After changing the engine oil and oil filter, reset the

system with the engine oil change light reset switch so

that the light goes out. The system must also be reset if

the engine oil and oil filter are changed before the

warning light comes on. If you do not reset the system, it

cannot inform you of the correct time to change the

engine oil.

2. Turn the ignition key to the "ON" position while keeping

the odometer reset button pressed.

Hold the button for at least 5 seconds. The total odometer

will display "000000" and the control will go out.

If the reset system fails, the light will continue to flash.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

156

Oil maintenance management system

(diesel engines, with combined

display)

The Oil Maintenance Management System

(OMMS) is designed to inform you

through reports when the oil and oil filter

need to be changed.

CHANGING ENGINE OIL AND OIL-

JOHN FILTER

Change the engine oil and oil filter in any of

the following cases:

• When the engine oil change warning message

appears, the main warning light will illuminate

and a warning tone will sound.

MOTOR REPLACEMENT WARNING MESSAGE

MY OIL

• When the system is being

This message appears when you turn the ignition

key to the "ON" position. After about 5 seconds,

the message disappears. This means that the

repaired. • When the engine oil change

warning message does not appear

even if 2 years have passed since the oil change.

system is working normally.

• When the engine oil change warning

message does not appear even though

it has been more than 30,000 km since

the oil change.

If this message appears while driving, replace the

engine oil and oil filter at the earliest opportunity

using the appropriate replacement parts. For

more information on oil grade and viscosity - see

The lighting interval may vary according to

driving conditions.

"Checking the engine oil level" on page 372 in

chapter 7ÿ2.

Because the condition of the engine oil

deteriorates over time, there are times

when it is necessary to change the engine

oil before the engine oil change warning

message appears. In these cases, replace

the engine oil and oil filter according to

the maintenance schedule (Engine oil

maintenance intervals - see "Toyota

After changing the engine oil and oil filter,

reset the system with the engine oil change

warning message reset switch so that the

message disappears. The system must also

be reset if the engine oil and oil filter are

changed before the message appears. If you

do not reset the system, it cannot inform you

of the correct time to change the engine oil.

Service Book" or "Toyota Warranty Book".)

NOTICE

Reset the system after changing the

engine oil and oil filter. (System reset

procedure - see "SYSTEM RESET" on

page 157 in this chapter.)

If you do not reset the system, it cannot

inform you of the correct time to change

the engine oil and oil filter.

Machine Translated by Google

157

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

Combined Display –

If any of the following situations occur,

the system may not operate normally.

Have the vehicle inspected by any

authorized Toyota dealer or workshop, or

by another properly qualified and equipped

professional. • When the ignition key is

turned to the "ON" position, the message

does not appear.

• After changing the engine oil and oil filter, even

if the system has been reset, the message

does not disappear or reappears soon.

SYSTEM RESET

The system must be reset after changing

the engine oil. Perform a system reset as

follows:

1. Turn the ignition key to the "ACC" or

"LOCK" position with the odometer

displayed. (Details - see "Total and two

trip meter display and instrument panel

lighting control" on page 153 in this

chapter.)

2. Turn the ignition key to the "ON" position while

keeping the odometer reset button pressed.

Hold the button for at least 5 seconds. The odometer

will display "000000" and the message will disappear.

1. Ride information

2. Hours

3. Outside temperature

4. "DISP." button.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

158

– Driving information

The combined display provides various information,

including the vehicle's driving conditions, the clock,

the outside temperature and warning messages if

there are any malfunctions or problems in the

vehicle.

Driving information is displayed during normal operation.

When the vehicle is stopped, you can select units or

hours on the display. However, if the vehicle has a

system failure or if there is any information that the

driver should be aware of, a warning message will

appear on the display. Details – see "– Warning

messages" on page 165.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

159

The display shows the following information when

1. Instantaneous fuel consumption ("Momentary

mpg" or Momentary l/100km)

the key is in the "ON" position.

Each time you press the "DISP." button, the display

switches between the following information.

Instantaneous fuel consumption is calculated and

displayed from distance and fuel consumption every

20 engine revolutions.

1. Instant fuel consumption 2.

The displayed value is updated in a short time.

Average fuel consumption

3. Driving range

Exact data may not be displayed in the following cases:

4. Average vehicle speed

• When the vehicle is stationary with the

engine running. (The display will show "–

5. Elapsed time

6. Settings

–.–") • When the vehicle is driving down a long

hill with engine braking. (The display will

show extremely low fuel consumption.)

Driving information displays general driving conditions.

Accuracy may vary depending on driving style and road

conditions.

The displayed calculation is reset when the ignition switch

is turned off.

When the ignition switch is on, the display mode last used

before the ignition switch was turned off appears.

1AD–FTV (with DPR Catalyst) and 2AD–FHV engines –

The vehicle momentarily uses more fuel than normal to

reduce vehicle emissions or maintain emission control

system performance. At that moment, the display will

show a higher fuel consumption.

If the power source has been disconnected, the display

will automatically reset to the initial setting.

When the instrument panel lighting is on, the brightness

of the display will be reduced.

Counter units can be changed. For details – see "– Clock

settings and unit selection" on page 161.

WARNING

2. Average fuel consumption ("Average mpg" or

"Average l/100km")

Do not adjust the display while driving. Adjust the

display only when the vehicle is stationary.

The average fuel consumption is calculated and

displayed from the total distance traveled and the total

fuel consumption while the engine is running.

The displayed value is updated every 10 seconds.

To reset the calculations, press and hold the "DISP."

button. longer than 1 second while showing the average

fuel consumption on the display.

Counter units can be changed. For details – see "– Clock

settings and unit selection" on page 161.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

160

3. Driving range ("Range miles" or "Range km")

5. Elapsed Time ("Elapsed Time")

The elapsed time since the engine was started is

displayed.

The distance that the vehicle can travel with the

remaining fuel is calculated and displayed from the

amount of remaining fuel and the last fuel

consumption.

When the engine is started, the driving time is counted

from 0:00. It can be displayed up to 99:59 (99 hours, 59

minutes). When the elapsed time exceeds 99:59, the

counter will reset to 0:00.

The driving range display shows the approximate

distance you can drive before the fuel gauge reaches

the "R" position. The distance is different from the current

distance traveled.

To reset the calculations, press and hold the "DISP."

longer than 1 second.

6. Settings

The displayed value is updated each time the fuel needed

to travel 1 km or 1 mile is consumed.

When the vehicle is stationary, you can change the

display to clock adjustment and unit selection by pressing

and holding the "DISP." button. (Details – see "– Clock

setting and unit selection" on page 161 in this chapter.)

When the vehicle is moving, pressing the "DISP." returns

the display to the current fuel consumption.

If the fuel gauge malfunctions, the mileage value will not

appear.

After refueling, the driving range is recalculated.

Actual driving range varies according to driving style and

road conditions. If the consumption is low, the driving

range will be longer than indicated. If the consumption

is high, the driving range will be shorter than indicated.

When the low fuel warning light comes on, add fuel,

even if the display shows you can drive the vehicle.

Counter units can be changed. For details – see "–

Clock settings and unit selection" on page 161.

4. Average vehicle speed ("Average mph" or "Average

km/h")

The average vehicle speed is calculated and

displayed from the total distance traveled and the

total driving time with the engine running.

The displayed value is updated every 10 seconds.

To reset the calculations, press and hold the "DISP."

longer than 1 second when the average speed of the

vehicle is displayed on the display.

Counter units can be changed. For details – see "–

Clock settings and unit selection" on page 161.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

161

– Clock setting and unit selection

The hours and units of the combined display can be

With units setting –

selected in the settings display.

To change the main menu display, press and hold the

"DISP." button.

To set the clock and select the display units, stop the

vehicle and press the button "DISP." change to display

Each time you press the "DISP." button, "Clock", "Unit"

or "Exit" is selected. Pressing and holding the "DISP."

settings.

button when "Clock" is selected will change the display

to the clock setting display. Pressing and holding the

(Instructions for changing the settings display – see "–

Driving information" on page 158 in this chapter.)

"DISP." button when "Unit" is selected will change the

display to the unit setting display. By pressing and

holding the "DISP." button when "Exit" is selected, the

display changes to the driving information display.

Without setting units -

By pressing and holding the "DISP." the display changes

directly to the clock setting display.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

162

After 5 seconds or more without operation, the time

display starts flashing. The normal display will return after

10 seconds.

Press the "DISP" button to select "Exit." and then press

and hold the button to change the display to the driving

information display.

If the power source has been disconnected from the clock,

the clock display will automatically be set to 12:00.

SETTING THE CLOCK

Use the "DISP." button to adjust the time.

However, if you quickly press and release the button, the

clock display changes to the driving information display.

See "– Driving information" on page 158 in this chapter.

Clock setting: Press and hold the "DISP." until the clock

display flashes. Then press the button until the desired

hour appears.

After 5 seconds or more without operation, the minute

display will start flashing. Then you can adjust the minute.

Minute setting: Press "DISP." until the desired minute

appears.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

163

– Outdoor temperature display

The displayed temperature range is from –30°C to 50°C.

The key must be in the "ON" position.

If there is any abnormality in the connection of the

outdoor temperature sensor, "ÿÿ°C" will appear on the

display. If "ÿÿ°C" appears on the display, contact any

authorized Toyota dealer or service center, or another

properly qualified and equipped professional.

When the outside temperature drops below 3°C while

driving, the temperature display will flash for 5 seconds

to indicate that the outside temperature is low. However,

when you turn on the ignition at a temperature of 3°C or

lower, the display will not flash.

SETTING THE UNITS

Choose to view units settings. Each time you press the

"DISP." the display will change according to the image

above. The unit can be set by pressing and holding the

"DISP." button.

Press the "DISP" button to select "Exit." and then press

and hold the button to change the display to the driving

information display.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

164

– Instrument panel lighting

control display

The display shows the following information.

Instrument panel lighting control display (when the

headlight switch is on)

– Shows the brightness of the instrument panel

illumination. The higher the height of the column, the

brighter the illumination of the instrument panel.

To adjust the brightness of the instrument panel

illumination, display the instrument panel illumination

control, press and hold the button until the desired

brightness is reached.

1. Instrument lighting control display

panel

2. Instrument panel lighting control button

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

165

– Warning messages

Reporting

Condition

Activity

Take the vehicle to any

authorized Toyota dealer or

A malfunction of the automatic

headlight tilt adjustment system

workshop, or to another

properly qualified and equipped

professional.

a

is detected.

The side door and/or rear door

are open.

Close the side door and/or rear

door.

b

c

d

The engine oil level is low.

Add engine oil.

The oil and oil filter need to be

changed.

Change the engine oil and oil filter.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

166

(a) Warning message of the automatic adjustment

of the inclination of the headlights

\If the message flashes or remains displayed while

driving, pull off the road to a safe place and stop the

engine immediately.

Contact any authorized Toyota dealer or service center,

or other properly qualified and equipped professional for

assistance.

This message warns the driver that the automatic

headlamp leveling system has a malfunction.

The message may occasionally flash when the engine is

idling or may appear briefly during a hard stop. If the

message then disappears with a slight increase in gas,

there is no need to worry.

If a malfunction of the automatic headlamp leveling

system is detected, a message appears together with the

main warning light and a warning tone sounds if the

ignition key is in the "ON" position.

The message may appear when the engine oil level is

extremely low. The message is not intended to signal a

low oil level, it must be checked with an oil dipstick.

If this message appears, have the vehicle checked by

any authorized Toyota dealer or workshop, or by another

properly qualified and equipped professional.

NOTICE

Do not drive with the warning message displayed -

not even for a short distance.

(b) Door open warning message

You can destroy the engine.

(d) Engine oil change warning message

This message alerts the driver that some of the doors

are open.

If any of the doors are open, a message will appear and

the main warning light will illuminate.

This message alerts the driver to change the engine

oil and oil filter.

If the message appears, close all doors securely.

If the message appears together with the main warning

light and the warning tone sounds, change the engine oil

and oil filter at the earliest opportunity. This message will

remain displayed with the ignition switch on. To turn off

the message, press and hold the odometer reset button.

Detailed information - see "Oil Maintenance Management

System" on page 156 in this chapter.

(c) Low engine oil warning message

This message warns the driver that the engine oil is

too low.

If the engine oil is too low, a message appears together

with the main warning control and a warning tone sounds.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

167

Service lights and warning buzzers

If the light comes on or the buzzer

sounds...

Do this.

If the parking brake is released, stop immediately

and contact any authorized Toyota dealer or

service center, or another properly qualified and

equipped professional.

(a)

(b)

Fasten the driver's seat belt.

(light and buzzer)

(c)

Fasten the front passenger's seat belt.

(light and buzzer)

Stop immediately and contact any authorized Toyota

dealer or service center, or another properly qualified

and equipped professional.

(d)

(and)

Stop and check.

Add engine oil.

(f)

Take the vehicle to any authorized Toyota dealer

or workshop, or to another properly qualified and

equipped professional.

(g)

Low fuel warning

light

(h)

Fill the fuel tank.

Take the vehicle to any authorized Toyota dealer

or workshop, or to another properly qualified and

equipped professional. If the brake system warning light

is also on, stop immediately and contact any

(i)

authorized Toyota dealer or service center, or

another properly qualified and equipped professional.

(j)

Close all doors and the back door.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

168

If the light comes on or the buzzer

sounds...

Do this.

Take the vehicle immediately to any authorized Toyota dealer or

workshop, or to another properly qualified and equipped professional.

(k)

(l)

Drain the water.

(m)

Change the engine oil and oil filter.

Take the vehicle immediately to any authorized Toyota dealer or

workshop, or to another properly qualified and equipped professional.

(n)

Take the vehicle to any authorized Toyota dealer or workshop, or

to another properly qualified and equipped professional.

(the)

Take the vehicle to any authorized Toyota dealer or workshop, or

to another properly qualified and equipped professional.

(p)

(q)

Read the warning message on the combined display.

Buzzer alerting you to

(r)

Remove the key.

Turn off the lights.

remove the key

Buzzer alerting you to turn

off the lights

(s)

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

169

(a) Brake system warning light

WARNING

The warning light comes on in the following cases

when the ignition key is in the "ON" position.

If any of the following situations occur,

immediately stop the vehicle in a safe place and

contact any authorized Toyota dealer or service

center, or another properly qualified and equipped

professional.

• When the parking brake is applied ...

The warning light comes on for a few seconds when

you turn the ignition key to the "ON" position even

after the parking brake is released.

• The warning light does not go out even after

• When the brake fluid level is low ...

releasing the parking brake while the engine is running.

In this case, the brakes may not work properly

and the braking distance will be extended.

Depress the brake pedal firmly and stop the

vehicle immediately.

WARNING

It is dangerous to continue driving normally if the

brake fluid level is low.

• The brake system warning light stays on

together with the "ABS" warning light.

• When the vacuum is low (diesel engine

vehicles)...

In this case, not only will the anti-lock braking

system not work, but your car will also become

extremely unstable when braking.

In the following cases, have your vehicle checked

by any authorized Toyota dealer or service center,

or another properly qualified and equipped

professional:

(b) Driver seat belt warning light and buzzer

• When the ignition key is in the "ON" position, the

indicator light does not illuminate even if the

parking brake is applied.

A warning light and buzzer alert you to fasten your

driver's seat belt.

When you turn the ignition key to the "ON" or

"START" position, the warning light flashes if the

driver's seat belt is not on. The warning light will

flash until the driver puts on the seat belt.

• The warning light does not come on even if the ignition

key is turned on and the parking brake is released.

A brief illumination of the warning lamp during operation

does not signal a fault.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

170

Vehicles with front passenger seat belt warning light ÿ If

the vehicle speed exceeds 15 km/h with the seat belt not

on, the buzzer will sound for 30 seconds. Then, if the

seat belt is not on, the buzzer will sound a different tone

for the next 90 seconds. Even if the vehicle speed drops

below 15 km/h, the buzzer will continue to sound. To

(d) Charging system warning light

The warning light comes on when the ignition switch is

turned to the ON position and goes out when the engine

is started.

When there is a problem with the charging system while

the engine is running, the warning light comes on.

stop the buzzer, fasten your seat belt. If the buzzer still

sounds, make sure the front passenger's seat belt is on.

NOTICE

When the charging system warning light comes

on while the engine is running, there may have

been a malfunction, such as a broken engine drive

belt.

(c) Front passenger seat belt warning light and buzzer

A light and a buzzer remind you to fasten the front

passenger's seat belt.

If the warning light comes on, immediately stop the

vehicle in a safe place and contact any authorized

Toyota dealer or service center, or another properly

qualified and equipped professional.

When you turn the ignition key to the "ON" or "START"

position, the warning light flashes if the passenger is

sitting in the front seat and is not wearing a seat belt.

The warning light will flash until the front passenger

fastens their seat belt.

(e) Low engine oil pressure warning light

If the vehicle speed exceeds 15 km/h with the seat belt

not on, the buzzer will sound for 30 seconds. If the seat

belt is not on, the buzzer will sound in a different tone

for the next 90 seconds. Even if the vehicle speed drops

below 15 km/h, the buzzer will continue to sound. To

stop the buzzer, fasten your seat belt. If the buzzer still

sounds, make sure the driver's seat belt is on.

The warning light warns that the engine oil

pressure is too low.

If this warning light flashes or illuminates while driving,

pull over to a safe place off the road and turn off the

engine immediately. Call any authorized Toyota dealer

or service center, or another properly qualified and

equipped professional to assist you.

The warning light may occasionally flash while the engine

If you place luggage or other cargo on the front passenger

seat, depending on its weight and position on the seat,

sensors built into the seat may detect pressure, causing

the light to flash and the buzzer to sound.

is idling, or it may come on briefly after a sudden stop. If

the light then goes out when the gas is slightly added,

there is no need to worry.

The warning light may come on when the engine oil level

is too low. The indicator light is not intended for checking

the oil level, it must be checked with an oil dipstick.

NOTICE

Do not continue driving with the warning light on -

not even for a short distance. You can destroy the

engine.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

171

Others ÿ

The indicator light comes on in the following cases.

(f) Low engine oil level warning lamp (2AZÿFSE

engines,

1AD–FTV, 2AD–FTV and 2AD–FHV)

The light indicates that the engine oil level should be

checked. If the warning light comes on while driving on

uneven roads or on steep slopes, drive the vehicle to a

level place and check if the warning light goes out. If it

remains illuminated, check the oil level according to the

instructions in "Checking the engine oil level" on page

a. The problem is somewhere in the engine, automatic

transmission electrical system, or electronic throttle

control system.

b. The fuel tank is completely empty. (Instructions - see

"Fuel gauge" on page 152 in this chapter.)

372 in chapter 7ÿ2.

If the warning light comes on while driving in case a, have

your vehicle checked/repaired by any authorized Toyota

dealer or workshop, or another properly qualified and

equipped professional, as soon as possible.

When driving on steep slopes or uneven roads that

cause significant vehicle sway or cornering, the warning

light may come on due to the movement of engine oil in

the engine.

Motory 3ZZ-FE, 1ZZ-FE, 1AZ-FSE a 2AZ-FSE ÿ

Under normal conditions, due to oil consumption, the light

may come on earlier than the specified interval of the

maintenance schedule.

If the engine speed does not increase even when the gas

pedal is depressed, there may be a problem somewhere

in the electronic throttle control system.

This happens because the oil is used to a low level during

the maintenance schedule interval and is not a fault. (For

more information - see "Engine oil consumption data" on

page 288 in Chapter 2.)

Vibrations may occur at that point. However, if you press

the gas pedal harder and slower, you can drive your

vehicle at a low speed. Have your vehicle checked as

soon as possible by any authorized Toyota dealer or

service center, or another properly qualified and

equipped professional.

NOTICE

Leaving the engine running with low engine oil will

damage the engine.

(g) Malfunction indicator light

Vehicles with a gasoline engine

For some models ÿ

Even if this electronic throttle control system abnormality

clears while driving slowly, the system may not reset until

the engine is stopped and the ignition key is turned to the

"ACC" or "LOCK" position.

The light warns that there is a problem somewhere in

the engine's electrical system.

If the light comes on while driving, do not have your

vehicle checked as soon as possible/

repaired by any authorized Toyota dealer or service

center, or other properly qualified and equipped

professional.

WARNING

Be extra careful to avoid incorrect operation of the

accelerator pedal.

Machine Translated by Google

172

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

Vehicles with a diesel engine

(i) "ABS" warning light

The light warns that there is a problem somewhere in the

engine's electrical system, electronic engine management

system, or emission control system.

Vehicles without a vehicle stability control system ÿ

The warning light comes on when you turn the ignition

key to the "ON" position. If the anti-lock braking system is

working properly, the warning light will go out after a few

seconds. If the system fails, the light will come back on.

If the warning light comes on while driving, have your

vehicle checked/repaired as soon as possible by any

authorized Toyota dealer or service center, or another

properly qualified and equipped professional.

When the "ABS" warning light is on (and the brake

system warning light is off), then the anti-lock braking

system is not working, but the braking system is working

normally.

If the engine speed does not increase even when

the gas pedal is depressed, there may be a problem

somewhere in the electronic engine control system.

Stop the vehicle as soon as possible and contact any

authorized Toyota dealer or workshop, or another properly

qualified and equipped professional, or continue driving

with caution because the vehicle's performance will be

lower than normal, to any authorized Toyota dealer or

workshop, or other properly to a qualified and equipped

When the "ABS" warning light is on (and the brake system

warning light is off), then the anti-lock braking system is

not working, so the wheels may lock when braking hard

or braking on slippery surfaces.

If any of the following situations occur, it indicates a

malfunction of the parts that are monitored by the

warning light system. Contact any authorized Toyota

dealer or workshop, or other properly qualified and

equipped specialist, as soon as possible and have

the vehicle repaired.

professional.

Even if this electronic engine control system abnormality

clears while driving slowly, the system may not reset until

the engine is stopped and the ignition key is turned to the

"ACC" or "LOCK" position.

• The indicator light does not illuminate when the

(h) Low fuel warning light

ignition key is turned to the "ON" position, or

remains illuminated.

The warning light comes on when the fuel level in the tank

is very low. Fill the tank as soon as possible.

• The indicator light comes on while driving.

A brief illumination of the warning lamp during operation

does not signal a fault.

On slopes or curves, the low fuel warning light may come

on earlier than usual due to the movement of fuel in the

tank.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

173

If any of the following situations occur, it indicates a

malfunction of the parts that are monitored by the

warning light system. Contact any authorized Toyota

dealer or workshop, or other properly qualified and

equipped specialist, as soon as possible and have

the vehicle repaired.

WARNING

If the brake system warning light stays on together

with the "ABS" warning light, immediately stop the

vehicle in a safe place and contact any authorized

Toyota dealer or service center, or another properly

qualified and equipped specialist.

• The indicator light does not illuminate when the

ignition key is turned to the "ON" position, or

remains illuminated.

In this case, not only will the anti-lock braking

• The indicator light comes on while driving.

system not work, but your vehicle will also become

extremely unstable when braking.

A brief illumination of the warning light during

operation does not signal a fault.

WARNING

Vehicles with a vehicle stability control system ÿ

If the brake system warning light stays on together

with the "ABS" warning light, immediately stop the

vehicle in a safe place and contact any authorized

Toyota dealer or service center, or another properly

qualified and equipped specialist.

The warning light comes on when you turn the

ignition key to the "ON" position. If the anti-lock

braking system and auxiliary braking system

are working correctly, the warning light will go

out after a few seconds. If one of the systems

fails, the light will come back on.

When the "ABS" warning light is on (and the brake

system warning light is off), the anti-lock braking system,

auxiliary braking system, anti-skid system and vehicle

stability control system are not working, but the braking

system is working normally.

In this case, not only will the anti-lock braking

system not work, but your vehicle will also become

extremely unstable when braking.

When the "ABS" warning light is on (and the brake system

warning light is off), then the anti-lock braking system is

not working, so the wheels may lock when braking hard

or braking on slippery surfaces.

(j) Door open warning lamp

The light remains on until all side doors and rear doors

are fully closed.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

174

(k) SRS warning light

(m) Engine oil change indicator light (diesel engine)

The warning light comes on when you turn the

ignition key to the "ON" position. After about 6

seconds, the light will go out. It means that the airbag

and front seat belt pretensioner systems are working

properly.

The light will come on to alert you to change the oil and

oil filter.

If the light comes on, change the engine oil and oil filter

at the earliest opportunity. Details - see "Oil Maintenance

Management System" on page 154 in this chapter.

The warning light system monitors the airbag sensor

unit, front airbag sensor, side airbag sensor, side and

window airbag sensor, window airbag sensor, driver seat

position sensor, driver seat belt buckle switch, front seat

belt pretensioner unit, inflator, warning light, inter- cables

and power sources.

(n) Electric power steering system warning lamp

(3ZZÿFE and 1ZZÿFE engines)

The warning light comes on when you turn the

ignition key to the "ON" position. If the electric

power steering system is working properly, the

warning light will go out after a few seconds. If

the system fails, the light will come back on.

If any of the following situations occur, it indicates a

malfunction of the airbags or seat belt pretensioners.

Contact any authorized Toyota dealer or workshop, or

other properly qualified and equipped specialist, as soon

as possible.

If any of the following situations occur, it indicates

a malfunction of the parts that are monitored by the

warning light system. Contact any authorized Toyota

dealer or workshop, or other properly qualified and

equipped specialist, as soon as possible and have

the vehicle repaired.

• The warning light does not light up when the ignition

key is turned to the "ON" position, or remains lit for

more than 6 seconds or flashes.

• The indicator light does not illuminate when the

ignition key is turned to the "ON" position, or

remains illuminated.

• The indicator lights up or starts flashing

while driving.

• The warning light remains on while driving.

(l) Fuel filter warning light (diesel engine)

Illumination of the warning light when the engine

is running for a long time may not indicate a

malfunction. To make the light go out, start the

engine again and drive away.

The light warns that the amount of water accumulated

in the fuel filter has reached a certain level.

If the light comes on, have the vehicle checked by any

authorized Toyota dealer or service center, or another

properly qualified and equipped professional, as soon as

possible.

NOTICE

Never drive with the warning light on. Continuing

to drive with water collected in the fuel filter will

damage the fuel injection pump.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

175

• The warning light stays on after turning the

ignition key to the "ON" position.

WARNING

If the electric power steering system warning light

• The warning light comes on during

driving.

illuminates, take the vehicle to any authorized

Toyota dealer or workshop, or another properly

qualified and equipped professional, as soon as

possible. In this case, it is necessary to exert more

force on the steering wheel than usual when

turning. Hold the steering wheel firmly while driving.

When the "VSC" warning light comes on, the "TRC OFF"

light comes on even if the "TRC OFF" switch is not

pressed.

(q) Master warning lamp

If the main warning light comes on, a message will appear

on the combined display. Depending on the

circumstances, a warning tone may sound. (Instructions -

see "Warning messages" on page 165 in this chapter.)

(o) Warning light of the automatic headlamp leveling

system

(r) Key removal buzzer

The warning light warns that there is a problem

The buzzer alerts you to remove the key when you open

the driver's door and the ignition key is in the "ACC" or

"LOCK" position.

somewhere in the automatic headlight tilting system.

The warning light comes on when you turn the ignition

(s) Buzzer to indicate lights off

key to the "ON" position and goes out after a few

seconds.

The buzzer will sound if the headlight switch is left on and

the driver's door is opened with the key removed from the

ignition switch.

If the warning light comes on, have the vehicle checked

by any authorized Toyota dealer or service center, or

another properly qualified and equipped professional.

(p) "VSC" warning light

The light warns that there is a problem somewhere in the

vehicle's stability control system or in the anti-skid system.

The warning light comes on when you turn the ignition

key to the "ON" position and goes off after a few seconds.

If the light comes on while driving, the system is not

working. However, this did not create a problem that

would prevent you from continuing to drive, as conventional

braking works.

In the following cases, contact any authorized Toyota

dealer or service center, or another properly qualified and

equipped professional:

• The warning light does not illuminate when

the ignition key is turned to the "ON" position.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

176

CHECKING SERVICE LIGHTS (except low fuel

warning light)

If any service light or warning buzzer does not work as

described above, have it checked as soon as possible

by any authorized Toyota dealer or workshop, or another

properly qualified and equipped professional.

Without combined display –

1. Apply the parking brake.

2. Open one of the side doors, the rear

door or trunk lid.

The door open warning light should come on.

3. Close the door.

The door open light should go out

not

4. Turn the ignition key to the "ON" position,

but do not start the engine.

All service lights except the door open warning light

should come on.

The following lights will go out after a few seconds:

• "ABS" warning light

• "VSC" warning light

• Electric power steering warning light

• Warning light of the system of automatic adjustment

of the inclination of the headlights

• Engine oil change light

The SRS warning light will go out after approximately

6 seconds.

With combined display –

1. Apply the parking brake.

2. Turn the ignition key to the "ON" position,

but do not start the engine.

All service lights should come on.

The following lights will go out after a few seconds:

• "ABS" warning light

• "VSC" warning light

• Electric power steering warning light

The SRS warning light will go out after approximately

6 seconds.

Instruments, indicators and service lights for Your Toyota Avensis 4 Door Second Generation (2004-2009)

Related Topics

Popular Owner Manuals

Latest Owner Manuals