Get Instruments, indicators and service lights -> Combined Display Guide for Toyota Avensis 4 Door Second Generation (2004-2009)

Machine Translated by Google

157

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

Combined Display –

If any of the following situations occur,

the system may not operate normally.

Have the vehicle inspected by any

authorized Toyota dealer or workshop, or

by another properly qualified and equipped

professional. • When the ignition key is

turned to the "ON" position, the message

does not appear.

• After changing the engine oil and oil filter, even

if the system has been reset, the message

does not disappear or reappears soon.

SYSTEM RESET

The system must be reset after changing

the engine oil. Perform a system reset as

follows:

1. Turn the ignition key to the "ACC" or

"LOCK" position with the odometer

displayed. (Details - see "Total and two

trip meter display and instrument panel

lighting control" on page 153 in this

chapter.)

2. Turn the ignition key to the "ON" position while

keeping the odometer reset button pressed.

Hold the button for at least 5 seconds. The odometer

will display "000000" and the message will disappear.

1. Ride information

2. Hours

3. Outside temperature

4. "DISP." button.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

158

– Driving information

The combined display provides various information,

including the vehicle's driving conditions, the clock,

the outside temperature and warning messages if

there are any malfunctions or problems in the

vehicle.

Driving information is displayed during normal operation.

When the vehicle is stopped, you can select units or

hours on the display. However, if the vehicle has a

system failure or if there is any information that the

driver should be aware of, a warning message will

appear on the display. Details – see "– Warning

messages" on page 165.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

159

The display shows the following information when

1. Instantaneous fuel consumption ("Momentary

mpg" or Momentary l/100km)

the key is in the "ON" position.

Each time you press the "DISP." button, the display

switches between the following information.

Instantaneous fuel consumption is calculated and

displayed from distance and fuel consumption every

20 engine revolutions.

1. Instant fuel consumption 2.

The displayed value is updated in a short time.

Average fuel consumption

3. Driving range

Exact data may not be displayed in the following cases:

4. Average vehicle speed

• When the vehicle is stationary with the

engine running. (The display will show "–

5. Elapsed time

6. Settings

–.–") • When the vehicle is driving down a long

hill with engine braking. (The display will

show extremely low fuel consumption.)

Driving information displays general driving conditions.

Accuracy may vary depending on driving style and road

conditions.

The displayed calculation is reset when the ignition switch

is turned off.

When the ignition switch is on, the display mode last used

before the ignition switch was turned off appears.

1AD–FTV (with DPR Catalyst) and 2AD–FHV engines –

The vehicle momentarily uses more fuel than normal to

reduce vehicle emissions or maintain emission control

system performance. At that moment, the display will

show a higher fuel consumption.

If the power source has been disconnected, the display

will automatically reset to the initial setting.

When the instrument panel lighting is on, the brightness

of the display will be reduced.

Counter units can be changed. For details – see "– Clock

settings and unit selection" on page 161.

WARNING

2. Average fuel consumption ("Average mpg" or

"Average l/100km")

Do not adjust the display while driving. Adjust the

display only when the vehicle is stationary.

The average fuel consumption is calculated and

displayed from the total distance traveled and the total

fuel consumption while the engine is running.

The displayed value is updated every 10 seconds.

To reset the calculations, press and hold the "DISP."

button. longer than 1 second while showing the average

fuel consumption on the display.

Counter units can be changed. For details – see "– Clock

settings and unit selection" on page 161.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

160

3. Driving range ("Range miles" or "Range km")

5. Elapsed Time ("Elapsed Time")

The elapsed time since the engine was started is

displayed.

The distance that the vehicle can travel with the

remaining fuel is calculated and displayed from the

amount of remaining fuel and the last fuel

consumption.

When the engine is started, the driving time is counted

from 0:00. It can be displayed up to 99:59 (99 hours, 59

minutes). When the elapsed time exceeds 99:59, the

counter will reset to 0:00.

The driving range display shows the approximate

distance you can drive before the fuel gauge reaches

the "R" position. The distance is different from the current

distance traveled.

To reset the calculations, press and hold the "DISP."

longer than 1 second.

6. Settings

The displayed value is updated each time the fuel needed

to travel 1 km or 1 mile is consumed.

When the vehicle is stationary, you can change the

display to clock adjustment and unit selection by pressing

and holding the "DISP." button. (Details – see "– Clock

setting and unit selection" on page 161 in this chapter.)

When the vehicle is moving, pressing the "DISP." returns

the display to the current fuel consumption.

If the fuel gauge malfunctions, the mileage value will not

appear.

After refueling, the driving range is recalculated.

Actual driving range varies according to driving style and

road conditions. If the consumption is low, the driving

range will be longer than indicated. If the consumption

is high, the driving range will be shorter than indicated.

When the low fuel warning light comes on, add fuel,

even if the display shows you can drive the vehicle.

Counter units can be changed. For details – see "–

Clock settings and unit selection" on page 161.

4. Average vehicle speed ("Average mph" or "Average

km/h")

The average vehicle speed is calculated and

displayed from the total distance traveled and the

total driving time with the engine running.

The displayed value is updated every 10 seconds.

To reset the calculations, press and hold the "DISP."

longer than 1 second when the average speed of the

vehicle is displayed on the display.

Counter units can be changed. For details – see "–

Clock settings and unit selection" on page 161.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

161

– Clock setting and unit selection

The hours and units of the combined display can be

With units setting –

selected in the settings display.

To change the main menu display, press and hold the

"DISP." button.

To set the clock and select the display units, stop the

vehicle and press the button "DISP." change to display

Each time you press the "DISP." button, "Clock", "Unit"

or "Exit" is selected. Pressing and holding the "DISP."

settings.

button when "Clock" is selected will change the display

to the clock setting display. Pressing and holding the

(Instructions for changing the settings display – see "–

Driving information" on page 158 in this chapter.)

"DISP." button when "Unit" is selected will change the

display to the unit setting display. By pressing and

holding the "DISP." button when "Exit" is selected, the

display changes to the driving information display.

Without setting units -

By pressing and holding the "DISP." the display changes

directly to the clock setting display.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

162

After 5 seconds or more without operation, the time

display starts flashing. The normal display will return after

10 seconds.

Press the "DISP" button to select "Exit." and then press

and hold the button to change the display to the driving

information display.

If the power source has been disconnected from the clock,

the clock display will automatically be set to 12:00.

SETTING THE CLOCK

Use the "DISP." button to adjust the time.

However, if you quickly press and release the button, the

clock display changes to the driving information display.

See "– Driving information" on page 158 in this chapter.

Clock setting: Press and hold the "DISP." until the clock

display flashes. Then press the button until the desired

hour appears.

After 5 seconds or more without operation, the minute

display will start flashing. Then you can adjust the minute.

Minute setting: Press "DISP." until the desired minute

appears.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

163

– Outdoor temperature display

The displayed temperature range is from –30°C to 50°C.

The key must be in the "ON" position.

If there is any abnormality in the connection of the

outdoor temperature sensor, "ÿÿ°C" will appear on the

display. If "ÿÿ°C" appears on the display, contact any

authorized Toyota dealer or service center, or another

properly qualified and equipped professional.

When the outside temperature drops below 3°C while

driving, the temperature display will flash for 5 seconds

to indicate that the outside temperature is low. However,

when you turn on the ignition at a temperature of 3°C or

lower, the display will not flash.

SETTING THE UNITS

Choose to view units settings. Each time you press the

"DISP." the display will change according to the image

above. The unit can be set by pressing and holding the

"DISP." button.

Press the "DISP" button to select "Exit." and then press

and hold the button to change the display to the driving

information display.

Machine Translated by Google

INSTRUMENTS, INDICATORS AND SERVICE LIGHTS

164

– Instrument panel lighting

control display

The display shows the following information.

Instrument panel lighting control display (when the

headlight switch is on)

– Shows the brightness of the instrument panel

illumination. The higher the height of the column, the

brighter the illumination of the instrument panel.

To adjust the brightness of the instrument panel

illumination, display the instrument panel illumination

control, press and hold the button until the desired

brightness is reached.

1. Instrument lighting control display

panel

2. Instrument panel lighting control button

Instruments, indicators and service lights -> Combined Display for Your Toyota Avensis 4 Door Second Generation (2004-2009)

Related Topics

Instruments, indicators and service lights

Popular Owner Manuals

Latest Owner Manuals