Get Before driving -> Opening, closing and locking the doors Guide for Toyota C-Hr SUV Second Generation (2024-2026)

155

4-2. Opening, closing and locking the doors

4-2.Opening, closing and locking the doors

Check that the door is securely

locked.

Side doors

*

: The door unlock settings can be

changed.

The vehicle can be locked

and unlocked using the

entry function, wireless

remote control or door lock

switches.

I

Wireless remote control

Unlocking and locking the

doors from the outside

I

Smart key system

Carry the electronic key to

enable this function.

1 Locks all the doors

4

Check that the door is securely

locked.

2 Unlocks all the doors

Pressing the button unlocks the

driver’s door. Pressing the button

again within 5 seconds unlocks the

other doors.

Press and hold to open the win-

*

dows.

1 Grip the driver’s door handle

to unlock the door. Holding

the driver’s door handle for

approximately 2 seconds

unlocks all the doors. Grip

the front passenger's door

handle to unlock all the

*

: This setting must be customized

at your Toyota dealer.

ISwitching the door unlock func-

tion

It is possible to set which doors the

entry function unlocks using the

wireless remote control. Perform the

switching operation in the vehicle or

within approximately 3.2 ft. (1 m) of

the vehicle.

1 Turn the power switch off.

2 When the indicator light on the

doors.^*

Make sure to touch the sensor on

the back of the handle.

The doors cannot be unlocked for 3

seconds after the doors are locked.

key surface is not on, press and

hold

approximately 5 seconds while

pressing and holding

,

or

for

2 Touch the lock sensor (the

indentation on the side of the

front door handle) to lock all

the doors.

.

The setting changes each time an

156

4-2. Opening, closing and locking the doors

operation is performed, as shown

below. (When changing the setting

continuously, release the buttons,

wait for at least 5 seconds, and

repeat step 2.)

the doors have been

locked/unlocked. (Locked: Once;

Unlocked: Twice)

Side windows:

A buzzer sounds to indicate that the

side windows are operating.

Multi-informa-

Unlocking func-

tion dis-

ISecurity feature

tion

play/Beep

If a door is not opened within

approximately 60 seconds after the

vehicle is unlocked, the security fea-

ture automatically locks the vehicle

again. (However, depending on the

location of the electronic key, the

key may be detected as being in the

vehicle. In this case, vehicle may be

unlocked.)

Holding the

driver’s door han-

dle unlocks only

the driver’s door.

Holding the front

Exterior: Beeps

passenger door

3 times

handle unlocks all

the doors.

IWhen the door cannot be

locked by the lock sensor on

the surface of the door handle

Holding a front

door handle

unlocks all the

When the door cannot be locked

even if the lock sensor on the sur-

face of the door handle is touched

by a finger, touch the lock sensor

with the palm.

When gloves are being worn,

remove the gloves.

Exterior: Beeps

doors.

twice

To prevent unintended triggering of

the alarm, unlock the doors using

the wireless remote control and

open and close a door once after

the settings have been changed. (If

a door is not opened within 60 sec-

onds after

is pressed, the doors

will be locked again and the alarm

will automatically be set.)

In a case that the alarm is triggered,

immediately stop the alarm. (P.66)

IImpact detection door lock

IOpen door warning buzzer

If an attempt to lock the doors is

made when a door is not fully

closed, a buzzer sounds continu-

ously for 5 seconds. Fully close the

door to stop the buzzer, and lock the

vehicle once more.

release system

In the event that the vehicle is sub-

ject to a strong impact, all the doors

are unlocked. Depending on the

force of the impact or the type of

accident, however, the system may

not operate.

ISetting the alarm

Locking the doors will set the alarm

system. (P.66)

IOperation signals

IConditions affecting the opera-

tion of the smart key system or

wireless remote control

Doors:

A buzzer sounds and the emer-

gency flashers flash to indicate that

P.171

157

4-2. Opening, closing and locking the doors

IIf the smart key system or the

wireless remote control does

not operate properly

(Customizable features: P.525)

WARNING

GUse the mechanical key to lock

and unlock the doors. (P.495)

ITo prevent an accident

Observe the following precautions

while driving the vehicle.

Failure to do so may result in a

door opening and an occupant

falling out, resulting in death or

serious injury.

GReplace the key battery with a

new one if it is depleted. (P.450)

IIf the 12-volt battery is dis-

charged

The doors cannot be locked and

unlocked using the smart key sys-

tem or wireless remote control. Lock

or unlock the doors using the

mechanical key. (P.495)

GEnsure that all doors are prop-

erly closed and locked.

GDo not pull the inside handle of

the doors while driving.

Be especially careful for the

front doors, as the doors may

be opened even if the inside

lock buttons are in locked posi-

tion.

IRear seat reminder function

GIn order to remind you not to for-

get luggage, etc. in the rear seat,

when the power switch is turned

off after any of the following condi-

tions are met, a buzzer will sound

and a message will be displayed

on the multi-information display for

approximately 6 seconds.

4

GSet the rear door child-protector

locks when children are seated

in the rear seats.

• The EV system is started within 10

minutes after opening and closing

a rear door.

IWhen opening or closing a

door

• A rear door has been opened and

closed after the EV system was

started.

However, if a rear door is opened

and then closed within approxi-

mately 2 seconds, the rear seat

reminder function may not operate.

Check the surroundings of the

vehicle such as whether the vehi-

cle is on an incline, whether there

is enough space for a door to

open and whether a strong wind

is blowing. When opening or clos-

ing the door, hold the door handle

tightly to prepare for any unpre-

dictable movement.

GThe rear seat reminder function

determines that luggage, etc., has

been placed in a rear seat based

on opening and closing of a rear

door. Therefore, depending on the

situation, the rear seat reminder

function may not operate and you

may still forget luggage, etc., on

the rear seat, or it may operate

unnecessarily.

IWhen using the wireless

remote control and operating

the power windows

Operate the power window after

checking to make sure that there

is no possibility of any passenger

having any of their body parts

caught in the window. Also, do not

allow children to operate the wire-

less remote control. It is possible

for children and other passengers

to get caught in the power win-

dow.

GThe rear seat reminder function

can be enabled/disabled.

(P.524)

ICustomization

Settings (e.g. unlocking function

using a key) can be changed.

158

4-2. Opening, closing and locking the doors

vehicle.

Unlocking and locking the

doors from the inside

Depending on the position of the

electronic key, the key may not be

detected correctly and the door may

be locked.

I

Using the door lock

switches

IOpen door warning buzzer

If the vehicle speed reaches 3 mph

(5 km/h), a buzzer sounds to indi-

cate that the door(s) or the hood is

not fully closed.The open door(s) or

hood is displayed on the multi-infor-

mation display.

IWhen all the doors are locked

with the entry function or wire-

less remote control

GThe doors cannot be unlocked

with the door lock switch.

1 Locks all the doors

2 Unlocks all the doors

GThe door lock switches can be

reset by unlocking all the doors

with the entry function or wireless

remote control.

I

Using the inside lock but-

tons

Rear door child-protector

lock

The door cannot be opened

from inside the vehicle when the

lock is set.

1 Locks the door

2 Unlocks the door

The front doors can be opened by

pulling the inside handle even if the

lock buttons are in the lock position.

ILocking the front doors from

the outside without a key

1 Move the inside lock button to

the lock position. (P.158)

2 Close the door.

The door cannot be locked if the

power switch is in ACC or ON, or

the electronic key is left inside the

1 Unlock

2 Lock

159

4-2. Opening, closing and locking the doors

These locks can be set to prevent

children from opening the rear

doors. Push down on each rear

door switch to lock both rear doors.

Power back door

The power back door can be

opened using the power

back door opener switch,

smart key system or wire-

less remote control.

Automatic door locking

and unlocking systems

The following functions can be

set or canceled:

WARNING

IBefore driving the vehicle

For instructions on customizing,

refer to P.525.

Make sure that the power back

door is fully closed. If the power

back door is not fully closed, it

may open unexpectedly while

driving, causing an accident.

Function

Operation

All doors are

automatically

locked when the

vehicle speed is

approximately 12

mph (20 km/h) or

higher.

ICaution while driving

4

Speed linked

door locking

function

GKeep the power back door

closed while driving.

If the power back door is left

open, it may hit nearby objects

while driving or luggage may be

unexpectedly thrown out, caus-

ing an accident.

All doors are

automatically

locked when the

shift position is

shifted to a posi-

tion other than P.

Shift position

linked door lock-

ing function

GNever let anyone sit in the lug-

gage compartment. In the event

of sudden braking, sudden

swerving or a collision, they are

susceptible to death or serious

injury.

All doors are

automatically

unlocked when

shift position is

shifted to P.

Shift position

linked door

unlocking func-

tion

IWhen children are in the vehi-

cle

Observe the following precau-

tions.

Failure to do so may result in

death or serious injury.

All doors are

automatically

unlocked when

driver’s door is

opened within

approximately 45

seconds after

turning the power

switch off.

GDo not allow children to play in

the luggage compartment.

If a child is accidentally locked

in the luggage compartment,

they could have heat exhaus-

tion or other injuries.

Driver’s door

linked door

unlocking func-

tion

160

4-2. Opening, closing and locking the doors

GWhen closing the power back

WARNING

door, take extra care to prevent

your fingers, etc., from being

caught.

GDo not allow a child to open or

close the power back door.

Doing so may cause the power

back door to move unexpect-

edly, or cause the child’s hands,

arms, head, or neck to be

caught by the closing power

back door.

IOperating the power back

door

Observe the following precau-

tions.

Failure to do so may cause parts

of the body to be caught, resulting

in death or serious injury.

GRemove any heavy loads, such

as snow and ice, from the

power back door before open-

ing it. Failure to do so may

cause the power back door to

suddenly shut again after it is

opened.

GWhen closing the power back

door, make sure to press it

lightly on its outer surface. If the

back door handle is used to fully

close the power back door, it

may result in hands or arms

being caught.

GDo not pull on the back door

spindle (P.167) to close the

back door, and do not hang on

the back door spindle.

Doing so may cause hands to

be caught or the back door spin-

dle to break, causing an acci-

dent.

GWhen opening or closing the

power back door, thoroughly

check to make sure the sur-

rounding area is safe.

GIf a bicycle carrier or similar

heavy object is attached to the

power back door, it may sud-

denly shut again after being

opened, causing someone’s

hands, arms, head or neck to be

caught and injured. When

installing an accessory part to

the power back door, using a

genuine Toyota part is recom-

mended.

GIf anyone is in the vicinity, make

sure they are safe and let them

know that the power back door

is about to open or close.

GUse caution when opening or

closing the power back door in

windy weather as it may move

abruptly in strong wind.

GThe back door may suddenly

shut if it is not opened fully,

while on a steep incline. Make

sure that the back door is

secured before using the lug-

gage compartment.

Unlocking and locking the

power back door from the

outside

I

Smart key system

Carry the electronic key to

enable this function.

161

4-2. Opening, closing and locking the doors

imately 1 second will operate the

power back door in the opposite

direction.

*

: Opening of the power back door

when it is locked can be disabled

by a customized setting.

(P.525)

1 Unlocks all the doors

The doors cannot be unlocked for 3

seconds after the doors are locked.

2 Locks all the doors

Check that the door is securely

locked.

I

Wireless remote control

4

I

Using the power back door

switch on the instrument

panel

P.155

Unlocking and locking the

back door from the inside

Press and hold the switch.

The power back door automatically

opens/closes.

I

Door lock switch

Unlock the back door before oper-

ating.

P.158

Pressing the switch while the power

back door is opening/closing stops

the operation. When the switch is

pressed and held again during the

halted operation, the back door will

perform the reverse operation.

Opening/closing the

power back door

I

Using the wireless remote

control

Press and hold the switch for

approximately 1 second.

The power back door automatically

opens/closes.

The power back door can be oper-

*

ated when it is locked .

Pressing the switch while the power

back door is opening/closing will

stop the operation. Pressing and

holding the switch again for approx-

162

4-2. Opening, closing and locking the doors

I

Opening the back door

using the back door opener

switch

When the back door is

unlocked: Press the back door

opener switch.

When the back door is locked:

While carrying the electronic key

on your person, press and hold

the back door opener switch.

 Close the back door and lock

all doors (close & lock func-

tion)

The power back door automatically

opens.

Close all of the doors except the

back door, carrying an electronic

Pressing the switch while the back

door is opening stops the opera-

tion. Pressing the switch again will

open the back door automatically.

key and press the

switch on

the lower part of the back door.

A different buzzer than the normal

one will sound and the power back

door will begin closing automati-

cally. When the power back door is

closed, all of the doors will lock

simultaneously and operation sig-

nals will indicate that all of the

doors have been locked.

Pressing the

switch while the

power back door is operating will

I

Using the power back door

switch on the back door

stop the operation. When the

switch is pressed again during the

halted operation, the back door will

be closed.

 Close

Press the switch.

The power back door automatically

closes.

Pressing the switch while the back

door is closing stops the operation.

When the switch is pressed again

during the halted operation, the

back door will perform the reverse

operation.

 Close the back door and lock

all doors (close & lock

163

4-2. Opening, closing and locking the doors

[Walk-Away] function)^*

If the switch is pressed after the

back door operation has stopped,

the close & lock (Walk- Away) func-

tion will go into standby again.

*

: This setting can be customized

by your Toyota dealer.

I

Closing the back door

using the back door handle

1 Close all of the doors except

the back door, carrying an

electronic key and press the

Lower the back door using the

back door handle, then a buzzer

sounds and the back door auto-

matically closes.

switch on the lower part

of the back door.

A different buzzer than the normal

one will sound and the close & lock

(Walk-Away) function will go into

standby.

4

ILuggage compartment light

GThe luggage compartment light

turns on when the back door is

opened.

GWhen the power switch is turned

off, the light will go off automati-

cally after 20 minutes.

2 While the buzzer is sounding,

move away from the back

door.

When the sensor detects that you

are away from the back door, the

emergency flashers will flash, and

the buzzer will sound. Depending

on the direction of moving away

from the back door, the location and

how to hold the electronic key or

circumstances, it may not be

detected properly.

All the doors other than the back

door will be locked, and after the

back door is closed, the back door

will also be locked. When all the

doors have been closed and

locked, the buzzer will sound and

the emergency flashers will flash.

IBack door closer

In the event that the back door is left

slightly open, the back door closer

will automatically close it to the fully

closed position.

Whatever the state of the power

switch, the back door closer oper-

ates.

IPower back door operating con-

ditions

The power back door can automati-

cally open and close under the fol-

lowing conditions:

GWhen the power back door sys-

tem is enabled. (P.167)

GWhen the power switch is in ON,

in addition to the above for the

opening operations, the back door

The standby state is canceled if you

do not move away from the back

door for 30 seconds. To operate the

function again, perform the proce-

dure again from the beginning.

164

4-2. Opening, closing and locking the doors

operates for any of the following

conditions:

hand, when the power back door is

open.

• Parking brake is engaged

• The brake pedal is depressed

• The shift position is in P.

When the following procedure is

performed, all the doors except the

power back door are locked and

then power back door will also be

locked at the same time it is closed.

IOperation of the power back

door

1 Close all doors, except the back

GA buzzer sounds and the emer-

gency flashers flash twice to indi-

cate that the back door is

opening/closing.

GWhen the power back door sys-

tem is disabled, the power back

door does not operate but it can

be opened and closed by hand.

door.

2 During the power back door clos-

ing operation, lock the doors

using the smart key system from

the side doors (P.155) or the

wireless remote control.

(P.155)

Operation signals will indicate that

all the doors have been closed and

locked (P.156).

GIf the electronic key is placed

inside the vehicle after starting a

close operation via the door

reserve lock function, the elec-

tronic key may become locked

inside the vehicle.

GIf the power back door does not

fully close due to the operation of

the jam protection function, etc.,

while the back door is automati-

cally closing after a door reserve

lock operation is performed, the

door reserve lock function is

canceled and all the doors will

unlock.

GWhen the power back door auto-

matically opens, if an abnormality

due to people or objects is

detected, operation will stop.

IJam protection function

Sensors are equipped on both sides

of the power back door. If anything

obstructs the power back door while

it is closing, the back door will auto-

matically operate in the opposite

direction or stop.

GBefore leaving the vehicle, make

sure that all the doors are closed

and locked.

IFall-down protection function

IClose & lock function

While the power back door is open-

ing automatically, applying exces-

sive force to it will stop the opening

operation to prevent the power back

door from suddenly shutting.

When the power back door is open,

this function closes the power back

door and then locks all of the doors

simultaneously.

When the following procedures are

performed and there are no elec-

tronic keys for the vehicle within the

vehicle, all of the doors will lock

when the power back door is com-

pletely closed.

IBack door closing assist

If the back door is lowered manually

when the back door is stopped at an

open position, the back door will

fully close automatically.

1 Close all of the doors except the

IBack door reserve lock function

power back door.

This function is a function which

reserves locking of all doors, before-

165

4-2. Opening, closing and locking the doors

2 While carrying an electronic key,

press the switch on the

the screwdriver with a rag.

lower part of the power back

door (P.162).

A different buzzer than the normal

one will sound and then the power

back door will begin closing auto-

matically. When the power back

door is closed, all of the doors will

lock simultaneously and operation

signals will indicate that all of the

doors have been locked.

2 Move the lever.

ISituations in which the close &

lock function may not operate

properly

In the following situations, the close

& lock function may not operate

properly:

4

GIf the

switch on the lower part

3 Install the cover.

ICustomization

of the power back door (P.162)

is pressed by a hand which is

holding an electronic key

Some functions can be customized.

(Customizable features: P.525)

GIf the

switch on the lower part

of the power back door (P.162)

is pressed when the electronic key

is in a bag, etc., that is placed on

the ground

WARNING

IBack door closer

GIn the event that the back door

is left slightly open, the back

door closer will automatically

close it to the fully closed posi-

tion. It takes several seconds

before the back door closer

begins to operate. Be careful

not to catch fingers or anything

else in the back door, as this

may cause bone fractures or

other serious injuries.

GIf the

switch on the lower part

of the power back door (P.162)

is pressed with the electronic key

not near the vehicle.

IWhen reconnecting the 12-volt

battery

To enable the power back door to

operate properly, close the back

door manually.

IIf the power back door opener

is inoperative

The power back door can be

unlocked from the inside.

1 Remove the cover.

To prevent damage, cover the tip of

166

4-2. Opening, closing and locking the doors

GIn the following situations, the

WARNING

power back door may detect an

abnormality and automatic

operation may be stopped. In

this case, the back door has to

be operated manually. Take

extra care in this situation, as

the back door may open or

close suddenly.

GUse caution when using the

back door closer as it still oper-

ates when the power back door

system is canceled.

IPower back door

Observe the following precautions

when operating the power back

door.

Failure to do so may cause death

or serious injury.

GCheck the safety of the sur-

rounding area to make sure

there are no obstacles or any-

thing that could cause any of

your belongings to get caught.

• When the back door contacts an

obstacle

• When the 12-volt battery volt-

age suddenly drops, such as

when the power switch is turned

to ON or the EV system is

started during automatic opera-

tion

GIf anyone is in the vicinity, make

sure they are safe and let them

know that the back door is

about to open or close

GIf a bicycle carrier or similar

heavy object is attached to the

back door, the power back door

may not operate, causing itself

to malfunction, or the back door

may suddenly shut again after

being opened, causing some-

one’s hands, arms, head or

neck to be caught and injured.

When installing an accessory

part to the back door, ask your

Toyota dealer for details.

GIf the power back door system is

turned off while the back door is

operating automatically, the

automatic operation is stopped.

The back door then has to be

operated manually. Take extra

care when on an incline, as the

back door may open or close

unexpectedly.

IJam protection function

Observe the following precau-

tions.

GIf the operating conditions of the

power back door are no longer

met, a buzzer may sound and

the back door may stop opening

or closing. The back door then

has to be operated manually.

Take extra care when on an

incline, as the back door may

open or close abruptly.

Failure to do so may cause death

or serious injury.

GNever use any part of your body

to intentionally activate the jam

protection function.

GThe jam protection function may

not work if something gets

caught just before the back door

fully closes. Be careful not to

catch fingers or anything else.

GOn an incline, the back door

may suddenly shut after it

opens. Make sure the back door

is fully open and secure.

GThe jam protection function may

not work depending on the

shape of the object that is

caught. Be careful not to catch

fingers or anything else.

167

4-2. Opening, closing and locking the doors

ITo prevent damage to the

power back door

NOTICE

IBack door spindles

GMake sure that there is no ice

between the back door and

The back door is equipped with

spindles that hold the back door in

place.

Observe the following precau-

tions. Failure to do so may cause

damage to the back door spindle,

resulting in malfunction.

frame that would prevent move-

ment of the back door. Operat-

ing the power back door when

excessive load is present on the

back door may cause a mal-

function.

GDo not apply excessive force to

the back door while the power

back door is operating.

GTake care not to damage the

sensors (installed on the right

and left edges of the power

back door) with a knife or other

sharp object. If the sensor is

disconnected, the power back

door will not close automatically.

4

GDo not attach any foreign

objects, such as stickers, plastic

sheets, or adhesives to the

spindle rod.

IClose & lock function

When closing the power back

door using the close & lock func-

tion, a different buzzer than the

normal one will sound before the

operation begins.

To check that the operation has

started correctly, check that a dif-

ferent buzzer than the normal one

has sounded.

Additionally, when the power back

door is fully closed and locked,

operation signals will indicate that

all of the doors have been locked.

GDo not touch the spindle rod

with gloves or other fabric items.

GDo not attach any accessories

other than genuine Toyota parts

to the power back door.

GDo not place your hand on the

spindle or apply lateral forces to

it.

ITo prevent back door closer

malfunction

Do not apply excessive force to

the back door while the back door

closer is operating. Applying

excessive force may cause the

back door closer to malfunction.

Before leaving the vehicle, make

sure that the operation signals

have operated and that all of the

doors are locked.

Canceling the power back

door system

The settings for the power back

door can be changed from the

settings screen of the multime-

dia display. (P.525)

168

4-2. Opening, closing and locking the doors

When the power back door settings

have been changed, they will not

be reset even if the power switch is

turned off.

After the buzzer sounds 4 times, it

sounds twice more. When the

power back door does the opening

operation the next time, the door will

open to the initial settings position.

To return the settings to their previ-

ous values, it is necessary to use

the settings screen of the multime-

dia display again.

Adjusting the open posi-

tion of the power back

door

ICustomization

The open position of the power

back door can be adjusted.

The automatic opening stop position

for the power back door can also be

changed from the multimedia dis-

play. (P.525)

When the stop position has been set

by both the vehicle side power back

door open/close switch and the mul-

timedia display, priority will be given

to whichever one was set most

recently.

1 Stop the back door in the

desirable position. (P.161)

2 Press and hold the power

back door switch on the back

door for 2 seconds.

• When the settings are com-

pleted, the buzzer sounds 4

times.

• When opening the back door

the next time, the back door

will stop at that position.

IReturning the power back door

automatic stop position to the

initial settings

Press and hold the power back door

switch on the back door for 7 sec-

onds.

169

4-2. Opening, closing and locking the doors

IEffective range (areas within

which the electronic key is

detected)

Smart key system

The following operations

can be performed simply by

carrying the electronic key

on your person, for example

in your pocket. The driver

should always carry the

electronic key.

When locking or unlocking the

doors

A

 Locks and unlocks the

doors (P.155)

The system can be operated when

the electronic key is within about 2.3

ft. (0.7 m) of the front door handles

and back door opener switch. (Only

the doors detecting the key can be

operated.)

 Locks and unlocks the back

door (P.155)

 Starts the EV system

(P.209)

4

When starting the EV system or

changing power switch modes

IAntenna location

The system can be operated when

the electronic key is inside the vehi-

cle.

IIf an alarm sounds or a warning

message is displayed

An alarm sounds and warning mes-

sages are displayed on the

multi-information display to protect

against unexpected accidents or

theft of the vehicle resulting from

erroneous operation. When a warn-

ing message is displayed, take

appropriate measures based on the

displayed message.

When only an alarm sounds, cir-

cumstances and correction proce-

dures are as follows.

Antennas outside the cabin

A

Antennas inside the cabin

GWhen an exterior alarm sounds

once for 5 seconds

Antenna inside the luggage

compartment

Antenna outside the luggage

compartment

170

4-2. Opening, closing and locking the doors

time to unlock the doors.

Correction pro-

cedure

Situation

• The electronic key has been left

near the vehicle for a certain

amount of time.

An attempt was

made to lock the

vehicle while a

door was open.

Close all of the

doors and lock

the doors again.

• The smart key system has not

been used for a few days or lon-

ger.

GIf the smart key system has not

been used for 14 days or longer,

the doors cannot be unlocked at

any doors except the driver’s door.

In this case, take hold of the

driver’s door handle, or use the

wireless remote control or the

mechanical key, to unlock the

doors.

GWhen an interior alarm pings

repeatedly

Correction pro-

cedure

Situation

The power

switch was

turned to ACC

ITurning an electronic key to

battery-saving mode

while the driver’s Turn the power

door was open switch off and

GWhen battery-saving mode is set,

battery depletion is minimized by

stopping the electronic key from

receiving radio waves.

(The driver’s

door was

close the driver’s

door.

opened when

the power switch

was in ACC).

Press

twice while pressing and

.

holding

The power

switch was

turned off while

the driver’s door

was open.

Confirm that the electronic key indi-

cator flashes 4 times.

Close the

driver’s door.

While the battery-saving mode is

set, the smart key system cannot be

used. To cancel the function, press

any of the electronic key buttons.

IIf “Key Detected in Vehicle” is

shown on the multi-information

display

An attempt was made to lock the

doors using the smart key system

while the electronic key was still

inside the vehicle. Retrieve the elec-

tronic key from the vehicle and lock

the doors again.

IBattery-saving function

GElectronic keys that will not be

used for long periods of time can

be set to the battery-saving mode

in advance.

The battery-saving function will be

activated in order to prevent the

electronic key battery and the

12-volt battery from being dis-

charged while the vehicle is not in

operation for a long time.

IWhen electronic key function

stops

If the position of the electronic key

has not changed for a certain

GIn the following situations, the

smart key system may take some

Before driving -> Opening, closing and locking the doors for Your Toyota C-Hr SUV Second Generation (2024-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals