Instruments and controls -> Warning lights, gauges and indicators for Your Vauxhall Corsa 4 Door First Generation (2014-2019)

Instruments and controls  
81  
Set date  
RDS clock synchronization  
The RDS signal of most VHF  
transmitters automatically sets the  
time. RDS time synchronisation can  
take a few minutes. Some  
transmitters do not send a correct  
time signal. In such cases, it is  
recommended to switch off the  
automatic time synchronisation.  
To switch between the options On  
and Off, repeatedly press the  
MENU-TUNE knob.  
Press the MENU-TUNE knob to enter  
the Set date submenu.  
Turn the MENU-TUNE knob to  
change the current value of the first  
setting.  
Press the MENU-TUNE knob to  
confirm the set value.  
The cursor then switches to the next  
value. If all values are set, you are  
automatically returned to the next  
higher menu level.  
Notice  
Colour-Info Display  
Press ; and then select the  
Settings screen button.  
Select Time & date settings to display  
the respective submenu.  
For a detailed description of menu  
operation, refer to the Infotainment  
manual.  
Set time format  
To select the desired time format, tap  
on the screen buttons 12 h or 24 h.  
Set time format  
Set date format  
To switch between the available  
options, repeatedly press the  
MENU-TUNE knob.  
To select the desired date format, tap  
on the < and > screen buttons and  
choose between the available  
options.  
Set date format  
To switch between the available  
options, repeatedly press the  
MENU-TUNE knob.  
82  
Instruments and controls  
Set time and date  
Do not connect any current-delivering  
accessories, e.g. electrical charging  
devices or batteries.  
Power outlets  
Do not damage the outlet by using  
unsuitable plugs.  
Stop-start system 3 135.  
Cigarette lighter  
To adjust the time and date settings,  
tap on the H and I screen buttons.  
A 12 Volt power outlet is located in the  
centre console.  
Do not exceed the maximum power  
RDS clock synchronization  
consumption of 120 watts.  
The RDS signal of most VHF  
transmitters automatically sets the  
time. RDS time synchronisation can  
take a few minutes. Some  
With ignition off, the power outlet is  
deactivated. Additionally, the power  
outlet is deactivated in the event of  
low vehicle battery voltage.  
Electrical accessories that are  
connected must comply with the  
electromagnetic compatibility  
requirements laid down in  
DIN VDE 40 839.  
transmitters do not send a correct  
time signal. In such cases, it is  
recommended to switch off the  
automatic time synchronisation.  
To activate or deactivate RDS clock  
synchronization, tap on the screen  
buttons On or Off.  
The cigarette lighter is located in the  
centre console.  
Press in cigarette lighter. It switches  
off automatically once the element is  
glowing. Pull out lighter.  
Instruments and controls  
Odometer  
83  
Ashtrays  
Warning lights, gauges  
and indicators  
Caution  
Instrument cluster  
To be used only for ash and not for  
combustible rubbish.  
The needles of the instruments briefly  
rotate to the end position when the  
ignition is switched on.  
Speedometer  
The bottom line displays the recorded  
distance in miles.  
Trip odometer  
The recorded distance is displayed  
since the last reset.  
Trip odometer counts up to  
9999 miles and then restarts at 0.  
The portable ashtray can be placed in  
the cupholders.  
Indicates vehicle speed.  
84  
Instruments and controls  
Midlevel display  
Uplevel display  
Tachometer  
To reset, press SET/CLR on the turn  
signal lever for a few seconds  
3 96.  
Two trip odometers are selectable for  
different trips.  
Displays the engine speed.  
Drive in a low engine speed range for  
each gear as much as possible.  
Select menu Trip/Fuel Information  
Menu ; by pressing Menu on the  
turn signal lever. Turn adjuster wheel  
on turn signal lever and select Trip 1  
or Trip 2. Each trip odometer can be  
reset separately by pressing  
SET/CLR on the turn signal lever for  
a few seconds on the respective  
menu.  
Caution  
If the needle is in the red warning  
zone, the maximum permitted  
engine speed is exceeded. Engine  
at risk.  
Instruments and controls  
85  
During liquid gas operation, the  
system automatically switches over to  
petrol operation when gas tanks are  
empty 3 85.  
LED off : petrol operation  
Fuel gauge  
LED  
: checking conditions for  
flashes  
fuel transition to liquid  
gas operation.  
Illuminates if conditions  
are fulfilled.  
Never run the fuel tank dry.  
Because of the fuel remaining in the  
tank, the top-up quantity may be less  
than the specified tank capacity.  
LED illu‐ : liquid gas operation  
minates  
LED  
: liquid gas tank is empty  
or failure in liquid gas  
system. A message is  
displayed in the Driver  
Information Centre.  
flashes  
five  
Fuel selector  
times  
and  
extin‐  
guishes  
Number of LEDs displays the level in  
the fuel tank.  
As soon as the liquid gas tank is  
empty, petrol operation is  
automatically engaged until the  
ignition is switched off.  
8
: fuel tank is full.  
LEDs  
The arrow indicates the  
vehicle side where the fuel  
filler flap is located.  
Fuel for liquid gas operation 3 176.  
During liquid gas operation, the level  
in the gas tank is displayed.  
Control indicator Y illuminates if the  
level in the tank is low. Refuel  
immediately if it flashes.  
Press LPG to switch between petrol  
and liquid gas operation. The LED in  
the button shows the current  
operating mode.  
86  
Instruments and controls  
Engine coolant temperature  
gauge  
Caution  
If engine coolant temperature is  
too high, stop vehicle, switch off  
engine. Danger to engine. Check  
coolant level.  
Service display  
The engine oil life system lets you  
know when to change the engine oil  
and filter. Based on driving  
conditions, the interval at which an  
engine oil and filter change will be  
indicated can vary considerably.  
To display the remaining engine oil  
life duration use turn signal lever  
buttons:  
Press MENU to select the Vehicle  
Information Menu ?.  
Turn the adjuster wheel to select  
Remaining Oil Life.  
Number of LEDs displays the coolant  
temperature.  
up to 3 LEDs  
: engine operating  
temperature not  
yet reached  
4 to 6 LEDs  
: normal operating  
temperature  
more than 6  
LEDs  
: temperature too  
high  
Instruments and controls  
87  
The remaining engine oil life duration  
is displayed in percent in the Driver  
Information Centre.  
Control indicators  
The control indicators described are  
not present in all vehicles. The  
description applies to all instrument  
versions.  
Reset  
Press SET/CLR on turn signal lever  
for several seconds to reset. The  
remaining engine oil life duration  
menu must be active. Switch on  
ignition, but not the engine.  
The system must be reset every time  
the engine oil is changed to ensure  
proper functionality. Seek the  
assistance of a workshop.  
Depending on the equipment, the  
position of the control indicators may  
vary. When the ignition is switched  
on, most control indicators will  
illuminate briefly as a functionality  
test.  
The control indicator colours mean:  
red  
: danger, important reminder  
yellow : warning, information, fault  
green : confirmation of activation  
blue : confirmation of activation  
white : confirmation of activation  
Next service  
When the system has calculated that  
engine oil life has diminished, a  
warning message appears in the  
Driver Information Centre. Have  
engine oil and filter changed by a  
workshop within one week or  
300 miles (whichever occurs first).  
Driver Information Centre 3 96.  
Service information 3 234.  
88  
Instruments and controls  
Control indicators in the instrument cluster  
Instruments and controls  
89  
Control indicators in the centre  
console  
R
Brake and clutch system  
Y
Low fuel 3 94  
3 92  
d
#
D
8
C
l
>
r
m
Immobiliser 3 94  
-
Operate pedal 3 92  
Reduced engine power 3 94  
Autostop 3 95  
u
Antilock brake system (ABS)  
3 92  
Exterior light 3 95  
High beam 3 95  
R
Gear shifting 3 92  
c
)
Power steering 3 92  
High beam assist 3 95  
Fog light 3 95  
Lane departure warning 3 92  
Ultrasonic parking assist  
3 93  
r
Rear fog light 3 95  
Cruise control 3 95  
Vehicle detected ahead 3 95  
Speed limiter 3 95  
Traffic sign assistant 3 95  
Door open 3 95  
n
Electronic Stability Control off  
3 93  
Overview  
A
L
b
k
Electronic Stability Control and  
Traction Control system 3 93  
O
X
Turn signal 3 89  
Seat belt reminder 3 90  
L
Traction Control system off  
3 93  
v
Airbag and belt tensioners  
3 90  
h
!
%
w
Preheating 3 93  
V
p
Z
Airbag deactivation 3 91  
Charging system 3 91  
Diesel particle filter 3 93  
Turn signal  
O illuminates or flashes green.  
Tyre pressure monitoring  
system 3 94  
Malfunction indicator light  
3 91  
Illuminates briefly  
The parking lights are switched on.  
I
Engine oil pressure 3 94  
g
Service vehicle soon 3 91  
90  
Instruments and controls  
X in the Driver Information Centre  
k for front passenger seat illuminates  
or flashes red in the centre console  
when the seat is occupied.  
Flashes  
A turn signal or the hazard warning  
flashers are activated.  
Rapid flashing: failure of a turn signal  
light or associated fuse.  
Bulb replacement 3 196, Fuses  
3 204.  
Turn signals 3 117.  
flashes or illuminates.  
Illuminates  
Illuminates  
After having started the engine for a  
minimum of 35 seconds, until the seat  
belt has been fastened.  
After the ignition has been switched  
on, until the seat belt has been  
fastened.  
Also illuminates if an unfastened seat  
belt is fastened whilst driving.  
Flashes  
After having started the engine for a  
maximum of 100 seconds, until the  
seat belt has been fastened.  
Flashes  
After starting-off, when the seat belt is  
Seat belt reminder  
Seat belt reminder on front seats  
X for driver's seat illuminates or  
flashes red in the tachometer.  
unfastened.  
Fastening the seat belt 3 41.  
Fastening the seat belt 3 41.  
Seat belt status on rear seats  
Airbag and belt tensioners  
v illuminates red.  
When the ignition is switched on, the  
control indicator illuminates for  
approx. four seconds. If it does not  
illuminate, does not go out after  
four seconds or illuminates whilst  
driving, there is a fault in the airbag  
system. Seek the assistance of a  
workshop. The airbags and belt  
pretensioners may fail to trigger in the  
event of an accident.  
Instruments and controls  
91  
Deployment of the belt pretensioners  
or airbags is indicated by continuous  
illumination of v.  
Illuminates when the ignition is  
9 Danger  
switched on and extinguishes shortly  
after the engine starts.  
Risk of fatal injury for a child using  
a child restraint system together  
with activated front passenger  
airbag.  
Risk of fatal injury for an adult  
person with deactivated front  
passenger airbag.  
Illuminates when the engine is  
running  
Fault in the emission control system.  
The permitted emission limits may be  
exceeded. Seek the assistance of a  
workshop immediately.  
9 Warning  
Have the cause of the fault  
remedied immediately by a  
workshop.  
Belt pretensioners, airbag system  
3 40, 3 43.  
Charging system  
p illuminates red.  
Illuminates when the ignition is  
switched on and extinguishes shortly  
after the engine starts.  
Flashes when the engine is  
running  
Fault that could lead to catalytic  
converter damage. Ease up on the  
accelerator until the flashing stops.  
Seek the assistance of a workshop  
immediately.  
Airbag deactivation  
V illuminates yellow.  
Illuminates for approx. 60 seconds  
after the ignition is switched on. The  
front passenger airbag is activated.  
* illuminates yellow.  
The front passenger airbag is  
deactivated 3 48.  
Illuminates when the engine is  
running  
Stop, switch off engine. Vehicle  
battery is not charging. Engine  
cooling may be interrupted. The  
brake servo unit may cease to be  
effective. Seek the assistance of a  
workshop.  
Service vehicle soon  
g illuminates yellow.  
Additionally, a warning message is  
displayed in the Driver Information  
Centre.  
The vehicle requires a service.  
Seek the assistance of a workshop.  
Vehicle messages 3 102.  
Malfunction indicator light  
Z illuminates or flashes yellow.  
92  
Instruments and controls  
On some versions, the operate pedal  
message is indicated in the Driver  
Information Display 3 102.  
Brake and clutch system  
Power steering  
R illuminates red.  
c illuminates yellow.  
The brake and clutch fluid level is too  
low, when manual parking brake is  
not applied 3 193.  
Illuminates with power steering  
disabled  
Failure in the power steering system.  
Consult a workshop.  
Antilock brake system  
(ABS)  
u illuminates yellow.  
9 Warning  
Illuminates for a few seconds after the  
ignition is switched on. The system is  
ready for operation when the control  
indicator extinguishes.  
If the control indicator does not go out  
after a few seconds, or if it illuminates  
while driving, there is a fault in the  
ABS. The brake system remains  
operational but without ABS  
regulation.  
Illumination of c and b  
Stop. Do not continue your  
journey. Consult a workshop.  
simultaneously  
Power steering system must be  
calibrated, system calibration 3 152.  
Illuminates when the manual parking  
brake is applied and ignition is  
switched on 3 149.  
Lane departure warning  
) illuminates green or flashes yellow.  
Operate pedal  
- illuminates or flashes yellow.  
Illuminates green  
System is switched on and ready to  
operate.  
Antilock brake system 3 148.  
Illuminates  
Clutch pedal must be depressed to  
start the engine in Autostop mode.  
Stop-start system 3 135.  
Gear shifting  
Flashes yellow  
System recognises an unintended  
lane change.  
R with the number of the next higher  
gear is indicated, when upshifting is  
recommended for fuel saving  
reasons.  
Flashes  
Lane departure warning 3 175.  
Clutch pedal must to be depressed for  
a main start of the engine 3 17,  
3 134.  
Instruments and controls  
93  
Preheating of diesel engine is  
activated. Only activates when  
outside temperature is low.  
Flashes  
Ultrasonic parking assist  
r illuminates yellow.  
Fault in system  
The system is actively engaged.  
Engine output may be reduced and  
the vehicle may be braked  
or  
Diesel particle filter  
automatically to a small degree.  
Fault due to sensors that are dirty or  
covered by ice or snow  
or  
Interference due to external sources  
of ultrasound. Once the source of  
interference is removed, the system  
will operate normally.  
Have the cause of the fault in the  
system remedied by a workshop.  
% illuminates or flashes yellow.  
Illuminates  
The diesel particle filter requires  
cleaning.  
Continue driving until %  
extinguishes. If possible, do not allow  
engine speed to drop below  
2000 rpm.  
A fault in the system is present. A  
warning message or warning code  
appears in the Driver Information  
Centre. Continued driving is possible.  
The system is not operational. Driving  
stability, however, may deteriorate  
depending on road surface  
conditions.  
Have the cause of the fault remedied  
by a workshop.  
Illuminates  
The diesel particle filter is full. Start  
cleaning process as soon as  
possible.  
Ultrasonic parking assist 3 159.  
Electronic Stability Control  
off  
Electronic Stability Control 3 151,  
Traction Control system 3 150.  
Flashes  
t illuminates yellow.  
The system is deactivated.  
The maximum filling level of the filter  
is reached. Start cleaning process  
immediately to avoid damage to the  
engine.  
Diesel particle filter 3 139, Stop-start  
system 3 135.  
Traction Control system off  
k illuminates yellow.  
The system is deactivated.  
Electronic Stability Control  
and Traction Control system  
b flashes or illuminates yellow.  
Preheating  
! illuminates yellow.  
94  
Instruments and controls  
Check oil level before seeking the  
Illuminates when the engine is  
running  
Tyre pressure monitoring  
system  
assistance of a workshop 3 190.  
w illuminates or flashes yellow.  
Caution  
Low fuel  
Y illuminates or flashes yellow.  
Illuminates  
Tyre pressure loss. Stop immediately  
and check tyre pressure.  
Engine lubrication may be  
interrupted. This may result in  
damage to the engine and/or  
locking of the drive wheels.  
Illuminates  
Level in fuel tank is too low.  
Flashes  
Flashes  
Fuel used up. Refuel immediately.  
Never run the fuel tank dry.  
Refuelling 3 178.  
Catalytic converter 3 140.  
1. Depress the clutch.  
2. Set selector lever to neutral.  
3. Move out of the flow of traffic as  
quickly as possible without  
impeding other vehicles.  
Fault in system or tyre without  
pressure sensor mounted (e.g. spare  
wheel). After 60-90 seconds the  
control indicator illuminates  
continuously. Consult a workshop.  
Tyre pressure monitoring system  
3 212.  
4. Switch off the ignition.  
Bleeding the diesel fuel system  
3 195.  
9 Warning  
Engine oil pressure  
I illuminates red.  
Illuminates when the ignition is  
switched on and extinguishes shortly  
after the engine starts.  
Immobiliser  
When the engine is off,  
considerably more force is needed  
to brake and steer.  
During an Autostop, the brake  
servo unit will still be operational.  
d flashes yellow.  
Fault in the immobiliser system. The  
engine cannot be started.  
Do not remove key until vehicle is  
stationary, otherwise the steering  
wheel lock could engage  
unexpectedly.  
Reduced engine power  
# illuminates yellow.  
Instruments and controls  
Speed limiter  
95  
The engine power is limited. Consult  
a workshop.  
Fog light  
> illuminates green.  
The front fog lights are on 3 117.  
L illuminates in the Driver  
Information Centre when Speed  
Autostop  
Autostop active  
D illuminates red or white.  
Engine is in an Autostop.  
Stop-start system 3 135.  
limiter is active. Set speed is indicated  
alongside L symbol.  
Rear fog light  
r illuminates yellow.  
The rear fog light is on 3 117.  
Speed limiter 3 155.  
Traffic sign assistant  
L displays detected traffic signs as a  
Cruise control  
control indicator.  
m illuminates white or green.  
Exterior light  
8 illuminates green.  
The exterior lights are on 3 112.  
Traffic sign assistant 3 171.  
Illuminates white  
The system is on.  
Door open  
h illuminates.  
Illuminates green  
Cruise control is active.  
High beam  
C illuminates blue.  
A door or the tailgate is open.  
Illuminated when high beam is on or  
during headlight flash 3 114.  
Cruise control 3 153.  
Vehicle detected ahead  
High beam assist  
A illuminates green.  
l illuminates green.  
A vehicle ahead is detected in the  
same lane.  
Forward collision alert 3 156.  
The high beam assist is activated  
3 115.