Get Vehicle care Guide for Vauxhall Insignia 4 Door First Generation (2008-2017)

216

Vehicle care

Vehicle storage

Storage for a long period of time

If the vehicle is to be stored for several

months:

General Information

Vehicle care

Accessories and vehicle

modifications

General Information ................... 216

Vehicle checks ........................... 217

Bulb replacement ....................... 226

Electrical system ........................ 236

Vehicle tools .............................. 242

Wheels and tyres ....................... 243

Jump starting ............................. 256

Towing ....................................... 258

Appearance care ....................... 261

We recommend to use genuine parts

and accessories and factory

■ Wash and wax the vehicle.

■ Have the wax in the engine

compartment and underbody

checked.

■ Clean and preserve rubber seals.

■ Fill up fuel tank completely.

■ Change engine oil.

■ Drain washer fluid reservoir.

■ Check coolant antifreeze and

corrosion protection.

■ Adjust tyre pressure to the value

specified for full load.

■ Park vehicle in dry, well ventilated

place. Engage first or reverse gear

or set selector lever to P. Prevent

the vehicle from rolling.

approved parts specific for your

vehicle type. We cannot assess or

guarantee reliability of other products

- even if they have a regulatory or

otherwise granted approval.

Do not make any modifications to the

electrical system, e.g. changes of

electronic control units (chip tuning).

Caution

When transporting the vehicle on

a train or on a recovery vehicle, the

mud flaps might be damaged.

■ Do not apply parking brake.

Vehicle care

217

■ Open bonnet, close all doors and

lock the vehicle.

■ Disconnect the clamp from the

negative terminal of the vehicle

battery. Beware that all systems are

not functional, e.g. anti-theft alarm

system.

website, where legally required. Only

entrust this work to an authorised

recycling centre.

Gas vehicles must be recycled by a

service centre authorised for gas

vehicles.

Vehicle checks

Performing work

Putting back into operation

When the vehicle is to be put back into

operation:

■ Connect the clamp to the negative

terminal of the vehicle battery.

Activate the electronics of the

power windows.

■ Check tyre pressure.

■ Fill up the washer fluid reservoir.

■ Check the engine oil level.

■ Check the coolant level.

9 Warning

Only perform engine compartment

checks when the ignition is off.

The cooling fan may start

operating even if the ignition is off.

■ Fit the number plate if necessary.

End-of-life vehicle

recovery

Information on end-of-life vehicle

recovery centres and the recycling of

end-of-life vehicles is available on our

218

Vehicle care

Engine oil

9 Danger

Check the engine oil manually on a

regular basis to prevent damage to

the engine. Ensure that the correct

specification of oil is used.

The ignition system and Xenon

headlights use extremely high

voltage. Do not touch.

Recommended fluids and lubricants

3 266.

Bonnet

Opening

Check with the vehicle on a level

surface. The engine must be at

operating temperature and switched

off for at least 5 minutes.

Pull out the dipstick, wipe it clean,

insert it to the stop on the handle, pull

out and read the engine oil level.

Insert dipstick to the stop on the

handle and make half a turn.

Move the safety catch sideways to the

left vehicle side and open the bonnet.

The bonnet is held open

automatically.

Air intake 3 150.

If the bonnet is opened during an

Autostop, the engine will be restarted

automatically for safety reasons.

Stop-start system 3 157.

Pull the release lever and return it to

its original position.

Closing

Lower the bonnet and allow it to drop

into the catch. Check that the bonnet

is engaged.

Vehicle care

219

When the engine oil level has

dropped to the MIN mark, top up

engine oil.

Different dipsticks are used

depending on engine variant.

The engine oil level must not exceed

the MAX mark on the dipstick.

Caution

We recommend the use of the same

grade of engine oil that was used at

last change.

Overfilled engine oil must be

drained or suctioned out.

Capacities 3 286, Engine oil quality/

viscosity 3 266.

Fit the cap on straight and tighten it.

220

Vehicle care

Automatic transmission fluid level

normally does not have to be

checked. To check the fluid level seek

the assistance of a workshop.

Automatic transmission

fluid

Caution

Engine coolant

Extremely small amounts of

contamination can cause

automatic transmission damage

and cause it to not work properly.

Do not allow contaminates to

contact the fluid side of the

reservoir cap or from entering the

reservoir.

The coolant provides freeze

protection down to approx. -28 °C. In

northern countries with very low

temperatures the factory filled coolant

provides frost protection down to

approx. -37 °C.

If the cooling system is cold, the

coolant level should be above the

filling line mark. Top up if the level is

low.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can cause

engine damage.

Vehicle care

221

On another version the filling line

mark is inside the filler opening. To

check open the cap.

General

contaminates to contact the fluid

side of the reservoir cap/dipstick or

from entering the reservoir.

9 Warning

Additional cooling circuit for Turbo

engine

Coolant container is fixed at the air

cleaner housing.

Allow the engine to cool before

opening the cap. Carefully open

the cap, relieving the pressure

slowly.

To top up use a 1:1 mixture of

released coolant concentrate mixed

with clean tap water. If no coolant

concentrate is available, use clean

tap water. Install the cap tightly. Have

the coolant concentration checked

and have the cause of the coolant

loss remedied by a workshop.

Power steering fluid level normally

does not have to be checked. If an

unusual noise sounds during steering

or the power steering reacts

conspicuous seek the assistance of a

workshop.

Power steering fluid

If the cooling system is cold, the

coolant level should be above the

filling line mark. Top up if the level is

low.

Caution

Extremely small amounts of

contamination can cause steering

system damage and cause it to not

work properly. Do not allow

222

Vehicle care

Washer fluid

Brakes

In the event of minimum thickness of

the brake lining, a squealing noise

sounds during braking.

Continued driving is possible but

have the brake lining replaced as

soon as possible.

Once new brake linings are installed,

do not brake unnecessarily hard for

the first few journeys.

Brake fluid

The brake fluid level must be between

the MIN and the MAX marks.

Fill with clean water mixed with a

suitable quantity of windscreen

washer fluid which contains

antifreeze.

9 Warning

If fluid level is below MIN seek the

assistance of a workshop.

Brake fluid is poisonous and

corrosive. Avoid contact with eyes,

skin, fabrics and painted surfaces.

Brake and clutch fluid 3 266.

Caution

Vehicle battery

Vehicles without stop-start system

will be equipped with a lead acid

battery. Vehicles with stop-start

system will be equipped with an AGM

battery which is not a lead acid

battery.

Only washer fluid with a sufficient

antifreeze concentration provides

protection at low temperatures or

a sudden drop in temperature.

Vehicle care

223

The vehicle battery is maintenance-

free provided that the driving profile

allows sufficient charging of the

battery. Short-distance-driving and

frequent engine starts can discharge

the battery. Avoid the use of

off with a dummy cap, and the

ventilation in the vicinity of the

Replacing the vehicle battery

Note

Any deviation from the instructions

given in this paragraph may lead to

a temporary deactivation of the stop-

start system.

negative terminal must be opened.

Only use vehicle batteries that allow

the fuse box to be mounted above the

battery.

In vehicles with stop-start system, be

sure to have the AGM (Absorptive

Glass Mat) battery replaced with an

AGM battery again.

unnecessary electrical consumers.

Batteries do not belong in household

waste. They must be disposed of at

an appropriate recycling collection

point.

Laying up the vehicle for more than

4 weeks can lead to vehicle battery

discharge. Disconnect the clamp from

the negative terminal of the vehicle

battery.

The vehicle battery is covered.

Remove the cover to replace the

battery. Lift up the cover at the rear

and unlatch it at the front.

Ensure the ignition is switched off

before connecting or disconnecting

the vehicle battery.

An AGM battery can be identified by

the label on the battery. We

recommend the use of an original

Opel battery.

When the battery is being replaced,

please ensure that there are no open

ventilation holes in the vicinity of the

positive terminal. If a ventilation hole

is open in this area, it must be closed

Battery discharge protection 3 136.

224

Vehicle care

Note

■ See the Owner’s Manual for further

information.

■ Explosive gas may be present in

the vicinity of the vehicle battery.

Warning label

Using an AGM battery different from

the original Opel battery might result

in a lower performance of the stop-

start system.

We recommend that you have the

vehicle battery replaced by a

workshop.

Diesel fuel system

bleeding

If the tank has been run dry, the diesel

fuel system must be bled. Switch on

the ignition three times for

Stop-start system 3 157.

Charging the vehicle battery

15 seconds at a time. Then crank the

engine for a maximum of

40 seconds. Repeat this process after

no less than 5 seconds. If the engine

fails to start, seek the assistance of a

workshop.

9 Warning

Meaning of symbols:

■ No sparks, naked flames or

smoking.

■ Always shield eyes. Explosive

gases can cause blindness or

injury.

On vehicles with stop-start

system, ensure that the charging

potential does not exceed

14.6 volts when using a battery

charger. Otherwise the battery

might be damaged.

■ Keep the vehicle battery out of

reach of children.

Jump starting 3 256.

■ The vehicle battery contains

sulphuric acid which could cause

blindness or serious burn injuries.

Vehicle care

225

Wiper blade on the rear window

Wiper blade replacement

Wiper blades on the windscreen

Disengage the wiper blade and

remove.

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Lift the wiper arm. Press the two

catches on the arm, disengage the

wiper blade and remove.

Attach the wiper blade slightly angled

to the wiper arm and push until it

engages.

Lift the wiper arm and open the

retaining clip.

Lower wiper arm carefully.

226

Vehicle care

Bi-Halogen Headlight (1)

Halogen headlights

Bulb replacement

Switch off the ignition and switch off

the relevant switch or close the doors.

Only hold a new bulb at the base. Do

not touch the bulb glass with bare

hands.

Use only the same bulb type for

replacement.

Replace headlight bulbs from within

the engine compartment.

Bulb check

After a bulb replacement switch on

the ignition, operate and check the

lights.

On left vehicle side pull filling pipe out

of the windscreen washer fluid

container.

Bi-Halogen Headlight (1) with one

bulb for low and high beam.

Sidelight/Daytime running light (2).

Front turn signal light (3)

Vehicle care

227

2. Rotate the bulb holder

anticlockwise to disengage.

Withdraw the bulb holder from the

reflector.

Sidelight/Daytime running light

(2)

1. Rotate the cap anticlockwise and

remove it.

1. Rotate cap anticlockwise and

withdraw from the reflector.

3. Disengage the bulb holder from

the plug connector by bending

apart slightly the retaining lug.

4. Replace the bulb and connect

with the plug.

5. Insert the bulb holder, engaging

the two lugs into the reflector and

rotate clockwise to secure.

6. Fit the cap and rotate clockwise.

228

Vehicle care

3. Remove the bulb from the socket

by pulling.

1. Rotate bulb socket anti-clockwise

to disengage. Withdraw the bulb

socket from the housing.

4. Replace and insert new bulb into

socket.

5. Insert the bulb socket into the

housing and let engage.

6. Fit the cap and rotate clockwise.

Sidelight/Daytime running light

with LEDs

On another version sidelight and

daytime running lights are designed

as LEDs. In case of defective have

LEDs replaced by a workshop.

2. Press snap-in tongues together

and move socket out of the

housing.

Front turn light (3)

2. Push bulb into socket slightly,

rotate anti-clockwise and remove.

3. Replace and insert new bulb into

socket by rotating clockwise.

4. Insert bulb socket in reflector,

rotate clockwise to engage.

Vehicle care

229

2. Rotate the bulb holder

Corner lighting

Xenon headlights

anticlockwise to disengage.

Withdraw the bulb holder from the

reflector.

9 Danger

Adaptive forward lighting system

uses Xenon headlights.

Xenon headlights work under

extremely high electrical voltage.

Do not touch. Have bulbs replaced

by a workshop.

Bulbs for front turn signal and

corner lighting can be changed.

Sidelight/Daytime running lights are

designed as Light Emitting Diodes

(LEDs) and cannot be changed.

1. Rotate the cap anticlockwise and

remove it.

3. Disengage the bulb from the plug

connector by unlatching and

pulling.

4. Replace the bulb and connect

bulb holder with the plug

connector.

5. Insert the bulb holder, engaging

the two lugs into the reflector and

rotate clockwise to secure.

6. Fit the cap and rotate clockwise.

230

Vehicle care

2. Rotate the bulb holder

anticlockwise to disengage.

Withdraw the bulb holder from the

reflector.

Front turn signal

Sidelight/Daytime running light

Sidelight and daytime running lights

are designed as LEDs. In case of

failure, have LEDs replaced by a

workshop.

Fog lights

The bulbs are accessible from the

underside of the vehicle.

1. Rotate the cap anticlockwise and

remove it.

3. Disengage the bulb holder from

the plug connector by unlatching

and pulling.

4. Replace the bulb and connect

bulb holder with the plug.

5. Insert the bulb holder, engaging

the two lugs into the reflector and

rotate clockwise to secure.

1. Turn the bulb holder anti-

clockwise and remove it from the

reflector.

Vehicle care

231

Tail lights

5-door Hatchback/4-door

Saloon

2. Disengage the bulb socket from

the plug connector by pressing

the retaining lug.

2. Unscrew three plastic securing

nuts from the inside by hand.

3. Remove and replace the bulb

socket with bulb and attach the

plug connector.

4. Insert the bulb socket into the

reflector and turn clockwise to

engage.

1. Remove cover from the inside of

the load compartment.

232

Vehicle care

3. Carefully withdraw the light

assembly from the recesses and

remove.

failure, have LEDs replaced by a

workshop.

5. Insert bulb holder into the tail light

assembly and turn clockwise. Fit

light assembly with the retaining

pins into the recesses of the

vehicle body and tighten the

securing nuts from the inside of

the load compartment. Close

cover.

Sports Tourer/Country Tourer

2. Unscrew three plastic securing

nuts by hand.

4. Turn bulb holder anticlockwise

and remove. Replace bulb by

withdrawing or turning:

Turn signal light 1

Rear fog light 2, only on driver side

Reverse light 3

Tail light and brake light are

designed as LEDs. In case of

1. Release and open the cover in the

tailgate.

Vehicle care

233

3. Carefully withdraw the light

assembly from the recesses and

remove.

pins into the recesses of the

tailgate and tighten the securing

nuts from the inside of the tailgate.

Close cover.

Additional tail lights in the tailgate

frame

1. Open tailgate.

3. Press out lamp housing from the

inside of the side trim panel.

4. Turn bulb holder anticlockwise

and remove. Replace bulb by

withdrawing:

Reverse light 1

Turn signal light 2

2. Release cover in side trim panel

and remove.

Tail light, brake light and rear fog

light are designed as LEDs. In

case of failure, have LEDs

replaced by a workshop.

5. Insert bulb holder into the tail light

assembly and turn clockwise. Fit

light assembly with the retaining

4. Rotate plastic nut anticlockwise

and remove from the bulb holder.

234

Vehicle care

5. Push bulb into socket slightly,

rotate anti-clockwise, remove and

renew bulb. Insert plastic nut into

bulb holder by rotating clockwise.

4. Insert bulb holder and turn

clockwise.

5. Insert left end of the lamp, slide to

the left and insert right end.

Tail light (1)

Turn signal light (2)

Number plate light

6. Insert bulb holder into the tailgate

frame. Close cover in the side trim

panel.

Side turn signal lights

2. Turn bulb holder anticlockwise

and remove from housing.

To replace bulb, remove lamp

housing:

1. Insert screwdriver in bulb

housing, press to the side and

release spring.

3. Pull bulb from bulb holder and

replace it.

1. Slide lamp to its left side and

remove with its right end.

Vehicle care

235

4. Pull bulb from bulb holder and

replace it.

5. Insert bulb holder into lamp

housing and turn clockwise.

6. Insert lamp into bumper and let

engage.

Interior lights

Courtesy light, reading lights

Have bulbs replaced by a workshop.

2. Remove lamp downwards, taking

care not to pull on the cable.

2. Press bulb slightly towards spring

clip and remove.

Load compartment light

3. Insert new bulb.

4. Install lamp.

Instrument panel

illumination

Have bulbs replaced by a workshop.

1. Prise the lamp out with a

screwdriver.

3. Remove bulb holder from lamp

housing by turning anticlockwise.

236

Vehicle care

Depending on the type of fuse, a

blown fuse can be recognized by its

melted wire. Do not replace the fuse

until the cause of the fault has been

remedied.

Some functions are protected by

several fuses.

Electrical system

Fuses

Data on the replacement fuse must

match the data on the defective fuse.

There are three fuse boxes in the

vehicle:

Fuses may also be inserted without

existence of a function.

■ in the front left of the engine

compartment,

■ in left-hand drive vehicles, in the

interior behind the storage

compartment, or, in right-hand

drive vehicles, behind the

glovebox,

Fuse extractor

A fuse extractor may be located in the

fuse box in the engine compartment.

There are different kinds of fuses in

the vehicle.

■ behind a cover on the left side of the

load compartment.

Before replacing a fuse, turn off the

respective switch and the ignition.

Vehicle care

237

Engine compartment fuse

box

Place the fuse extractor on the

various types of fuse from the top or

side, and withdraw fuse.

The fuse box is in the front left of the

engine compartment.

Disengage the cover, lift it upwards

and remove.

238

Vehicle care

No. Circuit

1

2

3

4

5

Transmission control module

16 Vacuum pump, mass air flow

meter, water in fuel sensor, DC

transformer

31 Air conditioning system

32 Body control module

33 Heated front seats

34 Sunroof

Engine control module

–

17

–

18 Adaptive forward lighting

19 Adaptive forward lighting

20 Fuel pump

Ignition, Transmission control

module, Engine control module

35 Infotainment system

36

–

6

7

8

9

Windscreen wiper

–

37 Right high beam

38 Left high beam

21 Rear power windows

22 ABS

Fuel injection, ignition system

39

40

–

23 Variable effort steering

24 Front power windows

25 Power outlets

10 Engine control module

11 Lambda probe

12 Starter

41 Vacuum pump

42 Radiator fan

26 ABS

43 Vehicle battery, DC transformer

(only on vehicles with stop-start

system)

27 Electric parking brake

28 Heated rear window

29 Left power seat

30 Right power seat

13 Sensor throttle heating

14 Lighting

44 Headlamp washer system

45 Radiator fan

15 Rear window wiper

Vehicle care

239

No. Circuit

62

Instrument panel fuse box

46 Terminal 87, main relay

47 Lambda probe

48 Fog lights

–

63 Rear window sensor

64 Adaptive forward lighting

49 Right low beam

50 Left low beam

51 Horn

65 Auxiliary pump (only on vehicles

with stop-start system)

66 Rear window washer system

67 Fuel system control module

52 Ignition

68

–

53 Ignition, ventilated front seats

54 Ignition

69 Vehicle battery sensor

70 Rain sensor

In left-hand drive vehicles, the fuse

box is behind the storage

compartment in the instrument panel.

55 Power windows, mirror folding

56 Windscreen washer

71 Vehicle battery sensor

Open compartment, compress the

locking tabs, fold compartment down

and remove.

After changing of defective fuses

close the fuse box cover and press

until it engages.

57

58

–

If the fuse box cover is not closed

correctly, malfunctions may occur.

59 Diesel fuel heating, emission

control system

60 Mirror heating

61 Mirror heating

240

Vehicle care

No. Circuit

1

Infotainment system, Info

16 Central locking system, tailgate

17 Air conditioning system

18 Transportation fuse

19 Memory

display

2

3

4

Body control unit

Infotainment system, Info

display

20

–

21 Instrument

5

Infotainment system, Info

display

22 Ignition

In right-hand drive vehicles, the fuse

box is located behind a cover in the

glovebox. Open the glovebox and

remove the cover.

6

7

8

9

Cigarette lighter

Power outlet

23 Body control unit

24 Body control unit

Body control unit

25

–

26 Power outlet load compartment

10 Body control unit

11 Interior fan

Power seats, No's. 12 and 13, have

an overload protection. The circuit will

be closed again after cooling down.

12

13

–

14 Diagnostic connector

15 Airbag

Vehicle care

241

No. Circuit

Load compartment fuse

box

1

Central locking system, Power

tailgate

2

3

4

5

6

7

8

9

Trailer module

–

Trailer socket

Steering wheel heating

–

Trailer socket

Sunroof

The fuse box is on the left side of the

load compartment behind a cover.

Remove the cover.

10 Central locking system, tailgate

11

12

13

14

–

15 Power tailgate lock

16 Air conditioning system

242

Vehicle care

No. Circuit

Vehicle tools

Tools

17

18

–

29 Trailer module, transportation

fuse

Vehicles with tyre repair kit

30 Side obstacle detector

19 Side obstacle detector

31

32

33

–

20 Side obstacle detector, venti‐

lated front seats

21 Active damping system, High

beam assist, Cruise control,

Traffic sign assistant, Lane

departure warning, trailer

module

34 Sunroof

35

36

37

–

22 Anti-theft alarm system

23 All-wheel drive, anti-theft alarm

system

The tools and the towing eye are

located together with the tyre repair

kit in a tool box below the floor cover

in the load compartment.

24

25

26

27

28

–

Vehicle care

243

Tyre sizes 205/60 R 16 and

235/45 R 18 are only suitable as

winter tyres.

Vehicles with spare wheel

Wheels and tyres

Tyre condition, wheel condition

Drive over edges slowly and at right

angles if possible. Driving over sharp

edges can cause tyre and wheel

damage. Do not trap tyres on the kerb

when parking.

Regularly check the wheels for

damage. Seek the assistance of a

workshop in the event of damage or

unusual wear.

Tyre designations

E.g. 215/60 R 16 95 H

215 = Tyre width, mm

60 = Cross-section ratio (tyre height

to tyre width), %

R

= Belt type: Radial

RF = Type: RunFlat

16 = Wheel diameter, inches

95 = Load index e.g. 95 is

equivalent to 690 kg

The jack with wheel wrench, the tools,

an extension bolt for securing a

damaged wheel and the towing eye

are placed in the tool box below the

spare wheel in the load compartment.

Spare wheel 3 254.

A label on the jack indicates the

vehicles for which the jack can be

used.

Winter tyres

H

= Speed code letter

Winter tyres improve driving safety at

temperatures below 7 °C and should

therefore be fitted on all wheels.

Speed code letter:

Q = up to 160 km/h

S = up to 180 km/h

T = up to 190 km/h

H = up to 210 km/h

V = up to 240 km/h

W = up to 270 km/h

In accordance with country-specific

regulations, affix the speed sticker in

the driver's field of view.

All tyre sizes are permitted as winter

tyres 3 287.

5-door Hatchback, 4-door Saloon,

Sports Tourer

244

Vehicle care

The tyre pressure data refers to cold

tyres. It applies to summer and winter

tyres.

Always inflate the spare tyre to the

pressure specified for full load.

The ECO tyre pressure serves to

achieve the smallest amount of fuel

consumption possible.

Incorrect tyre pressures will impair

safety, vehicle handling, comfort and

fuel economy and will increase tyre

wear.

Tyre pressures differ depending on

various options. For the correct tyre

pressure value, follow the procedure

below:

The driver is responsible for correct

adjustment of tyre pressure.

Tyre pressure

Check the pressure of cold tyres at

least every 14 days and before any

long journey. Do not forget the spare

wheel. This also applies to vehicles

with tyre pressure monitoring system.

9 Warning

If the pressure is too low, this can

result in considerable tyre warm-

up and internal damage, leading to

tread separation and even to tyre

blow-out at high speeds.

Unscrew the valve cap.

If the tyre pressure shall be reduced

or increased on a vehicle with tyre

pressure monitoring system, switch

off ignition. After adjusting tyre

pressure switch on ignition and select

the according setting on the page

Tyre load in the Driver Information

Centre, 3 111.

1. Identify drive axle and body style.

2. Identify the engine identifier code.

Engine data 3 273.

Tyre pressure monitoring

system

3. Identify the respective tyre.

The tyre pressure tables show all

possible tyre combinations 3 287.

For the tyres approved for your

vehicle, refer to the EEC Certificate of

Conformity provided with your vehicle

or other national registration

documents.

Tyre pressure 3 287.

The tyre and loading information label

on the left door frame indicates the

original equipment tyres and the

correspondent tyre pressures.

The tyre pressure monitoring system

checks the pressure of all four wheels

once a minute when vehicle speed

exceeds a certain limit.

Vehicle care

245

If w lights up, stop as soon as

possible and inflate the tyres as

recommended 3 287.

After inflating driving may be required

to update the tyre pressure values in

the Driver Information Centre. During

this time w may light up.

Caution

Tyre pressure monitoring system

warns just about low tyre pressure

condition and does not replace

regular tyre maintenance by the

driver.

If w lights up at lower temperatures

and extinguishes after some driving,

this could be an indicator for getting

low pressure. Check tyre pressure.

All wheels must be equipped with

pressure sensors and the tyres must

have the prescribed pressure.

Vehicle messages 3 120.

If the tyre pressure must be reduced

or increased, switch off ignition.

Note

System status and pressure warnings

are displayed by a message with the

corresponding tyre flashing in the

Driver Information Centre.

In countries where the tyre pressure

monitoring system is legally

required, the use of wheels without

pressure sensors will invalidate the

vehicle type approval.

Only mount wheels with pressure

sensors, otherwise the tyre pressure

will not be displayed and w

Select the Tyre pressure monitoring

page under the Info Menu in the

Driver Information Centre 3 111

illuminates continuously.

A spare wheel or temporary spare

wheel is not equipped with pressure

sensors. The tyre pressure

monitoring system is not operational

for these wheels. Control indicator w

illuminates. For the further three

wheels the system remains

A detected low tyre pressure

condition is indicated by the control

indicator w 3 108.

operational.

246

Vehicle care

The use of commercially available

liquid tyre repair kits can impair the

function of the system. Factory

approved repair kits can be used.

External high-power radio equipment

could disrupt the tyre pressure

monitoring system.

20 km/h. In this case $ can be

displayed or pressure values can

swap in the Driver Information Centre.

If problems occur during the relearn

process, a warning message is

displayed in the Driver Information

Centre.

Each time the tyres are replaced tyre

pressure monitoring system sensors

must be dismounted and serviced.

For the screwed sensor replace valve

core and sealing ring, for clipped

sensor replace complete valve stem.

Temperature dependency

Tyre pressure depends on the

temperature of the tyre. During

driving tyre temperature and pressure

increase.

The tyre pressure value displayed in

the Driver Information Centre shows

the actual tyre pressure. Therefore it

is important to check tyre pressure

with cold tyres.

Select:

■ Light for comfort pressure up to

3 people

■ Eco for Eco pressure up to

3 people

■ Max for full loading

Vehicle loading status

Adjust tyre pressure to load condition

according tyre information label or

tyre pressure chart 3 287, and select

the according setting in the Tyre

loading page under the Settings

menu in the Driver Information Centre

3 111.

Tread depth

Auto learn function

Check tread depth at regular

intervals.

After changing wheels the vehicle

must be stationary for approx.

20 minutes, before the system

recalculates. The following relearn

process takes up to 10 minutes of

driving with a minimum speed of

Tyres should be replaced for safety

reasons at a tread depth of 2-3 mm

(4 mm for winter tyres).

Vehicle care

247

For safety reasons, it is

Tyres age, even if they are not used.

We recommend tyre replacement

every 6 years.

Wheel covers

recommended that the tread depth of

the tyres on one axle should not vary

by more than 2 mm.

Wheel covers and tyres that are

factory approved for the respective

vehicle and comply with all of the

relevant wheel and tyre combination

requirements must be used.

If the wheel covers and tyres used are

not factory approved, the tyres must

not have a rim protection ridge.

Changing tyre and wheel

size

If tyres of a different size than those

fitted at the factory are used, it may be

necessary to reprogramme the

speedometer as well as the nominal

tyre pressure and make other vehicle

modifications.

Wheel covers must not impair brake

cooling.

9 Warning

After converting to a different tyre

size, have the label with tyre

pressures replaced.

Use of unsuitable tyres or wheel

covers could lead to sudden

pressure loss and thereby

accidents.

The legally permissible minimum

tread depth (1.6 mm) has been

reached when the tread has worn

down as far as one of the tread wear

indicators (TWI). Their position is

indicated by markings on the

sidewall.

If there is more wear at the front than

the rear, swap round front wheels and

rear wheels periodically. Ensure that

the direction of rotation of the wheels

remains the same.

9 Warning

Use of unsuitable tyres or wheels

may lead to accidents and will

invalidate the vehicle type

approval.

Wheel caps

Tyres of size 245/35 R20 have a

specific wheel cap. To remove the

cap from the dismantled wheel first

disengage the arms one by one. Then

press the cap in the middle area from

behind and remove it.

248

Vehicle care

To assemble first adjust the wheel

cap in order that the positioning leg

fits into the recess.

9 Warning

Damage may lead to tyre blowout.

Do not drive faster than 80 km/h.

Do not use for a lengthy period.

Steering and handling may be

Tyre chains

5-door Hatchback, 4-door Saloon,

Sports Tourer

Tyre chains are only permitted on

tyres of size 205/60 R 16,

215/60 R 16, 225/55 R 17,

225/45 R 18, 225/50 R 17 and

235/45 R 18.

affected.

If you have a flat tyre:

Apply the parking brake and engage

first gear, reverse gear or P.

Country Tourer

Tyre chains are only permitted on

tyres of size 235/45 R 18.

Temporary spare wheel

The use of tyre chains is not permitted

on the temporary spare wheel.

Tyre chains are only permitted on the

front wheels.

Always use fine mesh chains that add

no more than 10 mm to the tyre tread

and the inboard sides (including chain

lock).

Tyre repair kit

Minor damage to the tyre tread can be

repaired with the tyre repair kit.

Do not remove foreign bodies from

the tyres.

The tyre repair kit is in a compartment

under the floor cover in the load

compartment.

Tyre damage exceeding 4 mm or that

is at tyre's side wall cannot be

repaired with the tyre repair kit.

Vehicle care

249

1. Take the tyre repair kit from the

compartment.

2. Remove the compressor.

4. Screw the compressor air hose to

the connection on the sealant

bottle.

6. Unscrew valve cap from defective

tyre.

7. Screw the filler hose to the tyre

5. Fit the sealant bottle into the

valve.

3. Remove the electrical connection

cable and air hose from the

retainer on the compressor.

8. The switch on the compressor

stowage compartments on the

underside of the compressor.

Set the compressor near the tyre

in such a way that the sealant

bottle is upright.

must be set to J.

9. Connect the compressor plug to

the power outlet or cigarette

lighter socket.

To avoid discharging the battery,

we recommend running the

engine.

250

Vehicle care

14. Detach the tyre repair kit. Push

catch on bracket to remove

sealant bottle from bracket. Screw

tyre inflation hose to the free

connection of sealant bottle. This

prevents sealant from escaping.

Stow tyre repair kit in load

compartment.

15. Remove any excess sealant

using a cloth.

16. Take the label indicating

maximum permitted speed from

the sealant bottle and affix in the

driver's field of view.

17. Continue driving immediately so

that sealant is evenly distributed

in the tyre. After driving approx.

10 km (but no more than

If the prescribed tyre pressure is

not obtained within 10 minutes,

remove the tyre repair kit. Move

the vehicle one tyre rotation.

Reattach the tyre repair kit and

continue the filling procedure for

10 minutes. If the prescribed tyre

pressure is still not obtained, the

tyre is too badly damaged. Seek

the assistance of a workshop.

Drain excess tyre pressure with

the button over the pressure

indicator.

Do not run the compressor longer

than 10 minutes.

10. Set the rocker switch on the

compressor to I. The tyre is filled

with sealant.

11. The compressor pressure gauge

briefly indicates up to 6 bar whilst

the sealant bottle is emptying

(approx. 30 seconds). Then the

pressure starts to drop.

10 minutes), stop and check tyre

pressure. Screw compressor air

hose directly onto tyre valve and

compressor when doing this.

12. All of the sealant is pumped into

the tyre. Then the tyre is inflated.

13. The prescribed tyre pressure

should be obtained within

10 minutes. Tyre pressure

3 287. When the correct pressure

is obtained, switch off the

compressor.

Vehicle care

251

If unusual noise is heard or the

compressor becomes hot, turn

compressor off for at least 30

minutes.

The built-in safety valve opens at a

pressure of 7 bar.

Make the following preparations and

observe the following information:

■ Park the vehicle on a level, firm and

non-skid surface. The front wheels

must be in the straight-ahead

position.

Note the expiry date of the kit. After

this date its sealing capability is no

longer guaranteed. Pay attention to

storage information on sealant

bottle.

Replace the used sealant bottle.

Dispose of the bottle as prescribed

by applicable laws.

■ Apply the parking brake and

engage first gear, reverse gear or

P.

■ Remove the spare wheel 3 254.

■ Never change more than one wheel

at once.

■ Use the jack only to change wheels

in case of puncture, not for

seasonal winter or summer tyre

change.

■ If the ground on which the vehicle

is standing is soft, a solid board

(max. 1 cm thick) should be placed

under the jack.

■ Take heavy objects out of the

vehicle before jacking up.

■ No people or animals may be in the

vehicle when it is jacked-up.

If tyre pressure is more than

1.3 bar, set it to the correct value.

Repeat the procedure until there

is no more loss of pressure.

If the tyre pressure has fallen

below 1.3 bar, the vehicle must

not be used. Seek the assistance

of a workshop.

The compressor and sealant can be

used from approx. -30 °C.

The adapters supplied can be used

to pump up other items e.g.

footballs, air mattresses, inflatable

dinghies etc. They are located on the

underside of the compressor. To

remove, screw on compressor air

hose and withdraw adapter.

18. Stow away tyre repair kit in load

compartment.

Note

The driving characteristics of the

repaired tyre is severely affected,

therefore have this tyre replaced.

Wheel changing

Some vehicles are equipped with a

tyre repair kit instead of a spare wheel

3 248.

■ Never crawl under a jacked-up

vehicle.

252

Vehicle care

■ Do not start the vehicle when it is

raised on the jack.

■ Clean wheel nuts and thread with a

clean cloth before mounting the

wheel.

Alloy wheels: Disengage wheel

nut caps with a screwdriver and

remove. To protect the wheel,

place a soft cloth between the

screwdriver and the alloy wheel.

9 Warning

Do not grease wheel bolt, wheel

nut and wheel nut cone.

3. Some versions may have covered

the vehicle jacking point. Pull out

the cover sideways.

2. Fold out the wheel wrench and

install ensuring that it locates

securely and loosen each wheel

nut by half a turn.

The wheels might be protected by

locking wheel nuts. To loosen

these specific nuts first attach the

key adapter onto the head of the

nut before installing the wheel

wrench. The key adapter is

1. Disengage wheel nut caps with a

screwdriver and remove. Pull off

the wheel cover with the hook.

Vehicle tools 3 242.

located in the glovebox.

Vehicle care

253

4. Ensure the jack is correctly

positioned under the relevant

vehicle jacking point.

11. Align the valve hole in the wheel

cover with the tyre valve before

installing.

Install wheel nut caps.

12. Install vehicle jacking point cover.

13. Stow the replaced wheel 3 254,

the vehicle tools 3 242 and the

key adapter 3 70.

14. Check the tyre pressure of the

installed tyre and the wheel nut

torque as soon as possible.

Have the defective tyre renewed or

repaired as soon as possible.

Attach wheel wrench and with the

jack correctly aligned rotate wheel

wrench until wheel is clear of the

ground.

5. Set the jack to the necessary

height. Position it directly below

the jacking point in a manner that

prevents it from slipping.

6. Unscrew the wheel nuts.

7. Change the wheel. Spare wheel

3 254.

8. Screw on the wheel nuts.

9. Lower vehicle.

10. Install the wheel wrench ensuring

that it locates securely and tighten

each nut in a crosswise

sequence. Tightening torque is

150 Nm.

254

Vehicle care

The spare wheel has a steel rim.

Caution

Jacking position for lifting

platform

The use of a spare wheel that is

smaller than the other wheels or in

combination with winter tyres

could affect driveability. Have the

defective tyre replaced as soon as

possible.

Front arm position of the lifting

platform at the underbody.

Rear arm position of the lifting

platform at the underbody.

Spare wheel

Some vehicles are equipped with a

tyre repair kit instead of a spare

wheel.

If mounting a spare wheel, which is

different from the other wheels, this

wheel might be classified as a

temporary spare wheel and the

corresponding speed limits apply,

even though no label indicates this.

Seek the assistance of a workshop to

check the applicable speed limit.

The spare wheel is located in the load

compartment beneath the floor

covering.

To remove:

1. Open the floor cover.

Vehicle care

255

2. The spare wheel is secured with a

wing nut. Turn wing nut

anticlockwise and remove the

spare wheel.

Under the spare wheel there is the

box with vehicle tools.

3. When, after a wheel change, no

wheel is placed in the spare wheel

well, secure the tool box by

turning right back the wing nut and

close the floor cover.

Stowing the replaced full size

■ Store the tool box and the damaged

wheel outside up in the spare wheel

well and secure it by turning the

wing nut clockwise on the bolt.

The floor cover can be placed on the

projecting wheel.

To fit the spare wheel in the well after

renewing the defective wheel use the

short thread bolt again. Exchange the

bolt in the same way.

■ Install the hexagon key of the wheel

wrench ensuring that it locates

securely on the bolt.

■ Turn the wheel wrench

anticlockwise to loosen the bolt.

Remove the bolt.

■ Take the extension bolt from the

tool box 3 242 and screw it in hand-

tight using the hexagon key of the

wheel wrench.

wheel in the spare wheel well

The spare wheel well is not designed

for all permitted tyre sizes. If a wheel

wider than the spare must be stowed

in the spare wheel well, the thread

bolt for mounting the wheel must be

replaced by an extension bolt, located

in the tool box 3 242. To replace the

bolt:

■ Remove tool box from the spare

wheel well.

256

Vehicle care

If your vehicle gets a flat tyre on the

rear while towing another vehicle,

mount the temporary spare wheel in

the front and the full tyre in the rear.

Jump starting

Do not start with quick charger.

A vehicle with a discharged vehicle

battery can be started using jump

leads and the vehicle battery of

another vehicle.

9 Warning

Storing a jack, a wheel or other

equipment in the load

compartment could cause injury if

they are not fixed properly. During

a sudden stop or a collision, loose

equipment could strike someone.

Store wheel, jack and tools always

in the original storage location and

secure them by fixing.

Tyre chains 3 248.

Directional tyres

Fit directional tyres such that they roll

in the direction of travel. The rolling

direction is indicated by a symbol

(e.g. an arrow) on the sidewall.

9 Warning

Be extremely careful when starting

with jump leads. Any deviation

from the following instructions can

lead to injuries or damage caused

by battery explosion or damage to

the electrical systems of both

vehicles.

The following applies to tyres fitted

opposing the rolling direction:

■ Driveability may be affected. Have

the defective tyre renewed or

repaired as soon as possible.

■ Drive particularly carefully on wet

and snow-covered road surfaces.

Temporary spare wheel

Caution

The use of a spare wheel that is

smaller than the other wheels or in

combination with winter tyres

could affect driveability. Have the

defective tyre replaced as soon as

possible.

9 Warning

Avoid contact of the battery with

eyes, skin, fabrics and painted

surfaces. The fluid contains

sulphuric acid which can cause

injuries and damage in the event

of direct contact.

Only mount one temporary spare

wheel. Do not drive faster than

80 km/h. Take curves slowly. Do not

use for a long period of time.

Vehicle care

257

■ Never expose the vehicle battery to

naked flames or sparks.

■ A discharged vehicle battery can

already freeze at a temperature of

0 °C. Defrost the frozen battery

before connecting jump leads.

■ The vehicles must not come into

contact with each other during the

jump starting process.

■ Apply the parking brake,

transmission in neutral, automatic

transmission in P.

■ Wear eye protection and protective

clothing when handling a battery.

■ Use a booster battery with the

same voltage (12 Volts). Its

capacity (Ah) must not be much

less than that of the discharged

vehicle battery.

■ Use jump leads with insulated

terminals and a cross section of at

least 16 mm²(25 mm²for diesel

engines).

■ Do not disconnect the discharged

vehicle battery from the vehicle.

■ Switch off all unnecessary electrical

consumers.

Lead connection order:

1. Connect the red lead to the

positive terminal of the booster

battery.

2. Connect the other end of the red

lead to the positive terminal of the

discharged battery.

3. Connect the black lead to the

negative terminal of the booster

battery.

4. Connect the other end of the black

lead to a vehicle grounding point,

such as the engine block or an

engine mounting bolt. Connect as

■ If there is a cover over the vehicle

battery, remove it to charge or jump

start the vehicle battery. Lift up the

cover at the rear and unlatch it at

the front.

■ Open the positive terminal

protection caps of both vehicle

batteries.

■ Do not lean over the vehicle battery

during jump starting.

■ Do not allow the terminals of one

lead to touch those of the other

lead.

258

Vehicle care

far away from the discharged

battery as possible, however at

least 60 cm.

Towing

Towing the vehicle

Route the leads so that they cannot

catch on rotating parts in the engine

compartment.

To start the engine:

1. Start the engine of the vehicle

providing the jump.

2. After 5 minutes, start the other

engine. Start attempts should be

made for no longer than

15 seconds at an interval of

1 minute.

3. Allow both engines to idle for

approx. 3 minutes with the leads

connected.

4. Switch on electrical consumers

(e.g. headlights, heated rear

window) of the vehicle receiving

the jump start.

Country Tourer: insert a screwdriver

in the slot at the lower edge of the cap.

Release the cap by carefully moving

the screwdriver downwards. To

prevent damage it is recommended to

place a cloth between the screwdriver

and the frame.

5-door Hatchback, 4-door Saloon,

Sports Tourer: disengage cap at

bottom and remove downwards.

5. Reverse above sequence exactly

when removing leads.

Vehicle care

Caution

259

Drive slowly. Do not drive jerkily.

Excessive tractive force can

damage the vehicle.

When the engine is not running,

considerably more force is needed to

brake and steer.

To prevent the entry of exhaust gases

from the towing vehicle, switch on the

air recirculation and close the

windows.

Vehicles with manual transmission

and All-wheel drive: If the vehicle is

towed with all four wheels on the

ground then there are no technical

limitations for speed and distance. If

only one axle has been raised, the

maximum speed is 50 km/h. There is

no distance limitation.

Vehicles with automatic transmission

and Front-wheel drive: The vehicle

must be towed facing forwards, not

faster than 80 km/h nor further than

100 km. In all other cases and when

the transmission is defective, the front

axle must be raised off the ground.

Screw in the towing eye as far as it will

go until it stops in a horizontal

position.

Attach a tow rope – or better still a tow

rod – to the towing eye.

The towing eye must only be used for

towing and not for recovering the

vehicle.

Switch on ignition to release steering

wheel lock and to permit operation of

brake lights, horn and windscreen

wiper.

OPC: insert screwdriver in the slot at

the upper bend of the cap. Release

the cap by carefully moving the

screwdriver downwards. To prevent

damage it is recommended to place a

cloth between the screwdriver and

the frame.

The towing eye is stowed with the

vehicle tools 3 242.

Transmission in neutral.

260

Vehicle care

Vehicles with automatic transmission

and All-wheel drive: The vehicle must

be towed facing forwards. If the

vehicle is towed with all four wheels

on the ground, the maximum speed is

50 km/h and for a maximum of

50 km. If the front axle has been

raised, the maximum speed is

50 km/h. There is no distance

limitation.

5-door Hatchback, 4-door Saloon,

Sports Tourer: insert cap at the

bottom, turn slightly clockwise and

close cap.

Country Tourer: insert cap with the

upper flange into the recess and fix

cap by pushing.

OPC: insert cap with the lower flange

into the recess. Push the cap into the

bumper.

Seek the assistance of a workshop.

After towing, unscrew the towing eye.

Towing another vehicle

Country Tourer: insert a screwdriver

in the slot at the lower edge of the cap.

Release the cap by carefully moving

the screwdriver downwards. To

prevent damage it is recommended to

place a cloth between the screwdriver

and the frame.

The towing eye is stowed with the

vehicle tools 3 242.

5-door Hatchback, 4-door Saloon,

Sports Tourer, OPC: disengage cap

at bottom and remove downwards.

Vehicle care

261

Appearance care

Caution

Exterior care

Locks

Drive slowly. Do not drive jerkily.

Excessive tractive force can

damage the vehicle.

The locks are lubricated at the factory

using a high quality lock cylinder

grease. Use de-icing agent only when

absolutely necessary, as this has a

degreasing effect and impairs lock

function. After using de-icing agent,

have the locks regreased by a

workshop.

After towing, unscrew the towing eye.

Screw in the towing eye as far as it will

go until it stops in a horizontal

position.

The lashing eye at the rear

underneath the vehicle must never be

used as a towing eye.

Attach a tow rope – or better still a tow

rod – to the towing eye.

The towing eye must only be used for

towing and not for recovering a

vehicle.

Washing

The paintwork of your vehicle is

exposed to environmental influences.

Wash and wax your vehicle regularly.

When using automatic vehicle

washes, select a programme that

includes waxing.

5-door Hatchback, 4-door Saloon,

Sports Tourer, OPC: insert cap at the

bottom, turn slightly clockwise and

engage cap.

Country Tourer: insert cap with the

upper flange into the recess and fix

cap by pushing.

Bird droppings, dead insects, resin,

pollen and the like should be cleaned

off immediately, as they contain

aggressive constituents which can

cause paint damage.

262

Vehicle care

If using a vehicle wash, comply with

the vehicle wash manufacturer's

instructions. The windscreen wiper

and rear window wiper must be

switched off. Remove antenna and

external accessories such as roof

racks etc.

If you wash your vehicle by hand,

make sure that the insides of the

wheel housings are also thoroughly

rinsed out.

Wax painted parts of the vehicle

regularly.

Clean edges and folds on opened

doors and the bonnet as well as the

areas they cover.

Thoroughly rinse and leather-off the

vehicle. Rinse leather frequently. Use

separate leathers for painted and

glass surfaces: remnants of wax on

the windows will impair vision.

Have the door hinges of all doors

greased by a workshop.

Do not use hard objects to remove

spots of tar. Use tar removal spray on

painted surfaces.

Plastic body parts must not be treated

with wax or polishing agents.

Windows and windscreen wiper

blades

Use a soft lint-free cloth or chamois

leather together with window cleaner

and insect remover.

When cleaning the rear window from

inside, always wipe in parallel to the

heating element to prevent damage.

For mechanical removal of ice, use a

sharp-edged ice scraper. Press the

scraper firmly against the glass so

that no dirt can get under it and

scratch the glass.

Exterior lights

Headlight and other light covers are

made of plastic. Do not use any

abrasive or caustic agents, do not use

an ice scraper, and do not clean them

dry.

Clean smearing wiper blades with a

soft cloth and window cleaner.

Caution

Polishing and waxing

Wax the vehicle regularly (at the

latest when water no longer beads).

Otherwise, the paintwork will dry out.

Sunroof

Always use a cleaning agent with

a pH value of 4 to 9.

Do not use cleaning agents on hot

surfaces.

Never clean with solvents or abrasive

agents, fuels, aggressive media

(e.g. paint cleaner, acetone-

containing solutions etc.), acidic or

highly alkaline media or abrasive

pads. Do not apply wax or polishing

agents to the sunroof.

Polishing is necessary only if the paint

has become dull or if solid deposits

have become attached to it.

Paintwork polish with silicone forms a

protective film, making waxing

unnecessary.

Do not clean the engine compartment

with a steam-jet or high-pressure jet

cleaner.

Vehicle care

263

Before and after winter, wash the

underbody and have the protective

wax coating checked.

Wheels and tyres

Do not use high-pressure jet

cleaners.

Clean rims with a pH-neutral wheel

cleaner.

Interior care

Interior and upholstery

Only clean the vehicle interior,

Liquid gas system

including the instrument panel fascia

and panelling, with a dry cloth or

interior cleaner.

Rims are painted and can be treated

with the same agents as the body.

9 Danger

Clean the leather upholstery with

clear water and a soft cloth. In case of

heavy soiling, use leather care.

The instrument cluster and the

displays should only be cleaned using

a soft damp cloth. If necessary use a

weak soap solution.

Liquid gas is heavier than air and

can collect in sink points.

Take care when performing work

at the underbody in a pit.

Paintwork damage

Rectify minor paintwork damage with

a touch-up pen before rust forms.

Have more extensive damage or rust

areas repaired by a workshop.

For painting work and when using a

drying booth at a temperature above

60 °C, the liquid gas tank must be

removed.

Do not make any modifications to the

liquid gas system.

Underbody

Clean fabric upholstery with a

Some areas of the vehicle underbody

have a PVC undercoating while other

critical areas have a durable

protective wax coating.

vacuum cleaner and brush. Remove

stains with an upholstery cleaner.

Clothing fabrics may not be

colourfast. This could cause visible

discolourations, especially on light-

coloured upholstery. Removable

stains and discolourations should be

cleaned as soon as possible.

After the underbody is washed, check

the underbody and have it waxed if

necessary.

Bitumen/rubber materials could

damage the PVC coating. Have

underbody work carried out by a

workshop.

Towing equipment

Do not clean the coupling ball bar with

a steam-jet or high-pressure jet

cleaner.

Clean seat belts with lukewarm water

or interior cleaner.

264

Vehicle care

Caution

Close Velcro fasteners as open

Velcro fasteners on clothing could

damage seat upholstery.

The same applies to clothing with

sharp-edged objects, like zips or

belts or studded jeans.

Plastic and rubber parts

Plastic and rubber parts can be

cleaned with the same cleaner as

used to clean the body. Use interior

cleaner if necessary. Do not use any

other agent. Avoid solvents and petrol

in particular. Do not use high-

pressure jet cleaners.

Vehicle care for Your Vauxhall Insignia 4 Door First Generation (2008-2017)

Related Topics

Popular Owner Manuals

Latest Owner Manuals