2025-2026 Volvo EX30 4 Door Visibility, mirrors and exterior lights -> Driving lights User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Visibility, mirrors and exterior lights -> Driving lights for Your Volvo EX30 4 Door First Generation (2025-2026)

Note  
Exterior lighting may temporarily contain water from condensation. This is normal and all exterior lights are designed to  
withstand this. Condensation is normally vented out of the light housing after a period of time.  
9.1.1. Driving lights  
Driving lights mix automatic behaviours and direct controls which allow you to adapt to any situation or  
visibility conditions.  
Important  
The driver is always responsible for ensuring that the car is driven while using a lights mode that is suitable for the  
current driving conditions and local traffic regulations.  
Primary lighting  
You can choose between several different primary lighting modes in the display. Your selection sets a standard lighting  
behaviour.  
The automatic lights mode[1] allows your car to automatically detect and calculate which lighting mode is most suitable for the driving and environmental lighting  
conditions.  
You can manually select the passing beam to keep the front lights dipped.  
The position lights are points of illumination around the car that make your car more visible to other road users.  
Off deactivates all primary lighting modes.[2]  
Additional lights  
The rear fog light warns traffic behind you of your presence in poor light conditions. It is manually activated in the display.  
You can run tests from the display to check the lights on a connected trailer.  
[1]  
Auto  
[2]  
Some exterior lights may remain on when driving based on regulations in various market regions.  
9.1.1.1. Operating the driving lights  
Familiarise yourself with operating the lights that are available via the left-hand steering wheel stalk.  
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
203 / 396  
You can control some primary lighting modes behaviours using the left-hand steering wheel stalk.  
The horizontal stalk positions  
You can move the left-hand stalk forwards or backwards to switch between different lighting selections. The stalk always  
springs back to the neutral position.  
The selections available are:  
High beam on  
High beam off  
High beam flash  
1
When the automatic lights mode[ ] is selected in the display:  
Push the stalk twice to switch between the manual high beam and the automatic high beam.  
•
When the passing beam is manually selected in the centre display:  
Push the left-hand stalk to turn the manual high beam on.  
•
Pull the left-hand stalk fully to turn high beam off.  
•
A short pull of the stalk activates the high beam flash.  
•
The lights settings will reset to their default values between drives.  
Important  
Make sure that the car cameras are well-maintained and kept clean. If the cameras’ views are obscured by dirt, they will  
not be able to obtain enough information to properly direct the car’s lighting responses.  
[1]  
Auto  
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
204 / 396  
9.1.1.2. High beam  
The high beam is important for your driving visibility. There are different states you can use to suit your  
needs.  
Important  
Remember that your ability to see the road properly in low lighting conditions is important not just for your own safety,  
but for other road users and pedestrians too.  
The high beam is more powerful and has a longer reach of illumination than the passing beam. To use the high beam, you must  
first activate the automatic lights mode or passing beam.  
When the automatic high beam is active, the car automatically reacts to oncoming traffic to avoid dazzling other road users.  
Note  
The automatic high beam only activates at speeds over approximately 40 km/h (25 mph) and in low light.  
Use the left-hand steering wheel stalk to switch between the different high beam settings. There are symbols in the display that  
show which high beam setting is currently active. These include:  
The manual high beam is active.  
The automatic high beam is enabled.  
The automatic high beam is active.  
Important  
Make sure that the car cameras are well-maintained and kept clean. If the cameras’ views are obscured by dirt, they will  
not be able to obtain enough information to properly direct the car’s lighting responses.  
9.1.1.3. Passing beam  
The passing beam reduces the risk of dazzling other road users.  
The passing beam is part of the automatic lights mode. However, you can manually select the passing beam in the display.  
9.1.1.3.1. Activating the passing beam  
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
205 / 396  
The passing beam can be manually activated in the display.  
Manually activating the passing beam keeps the front lights dipped.  
Press the car symbol  
in the bottom bar and go to Settings.  
1
Go to Controls → Lights and displays → Exterior lights.  
2
3
4
Press the passing beam symbol  
.
Confirm your selection by pressing the OK button  
The passing beam is turned on.  
on the steering wheel.  
>
Deactivate the manual passing beam by selecting a different primary lighting mode.  
9.1.1.4. Activating the rear fog light  
The rear fog light is designed to warn traffic behind you of your presence in bad weather with poor light  
conditions.  
The rear fog light needs to be manually activated in the main area of the display.  
Press the car symbol  
in the bottom bar and go to Settings.  
1
Go to Controls → Lights and displays → Exterior lights → Rear fog light.  
2
3
Turn it on or off by pressing the fog light symbol  
.
9.1.1.5. Activating the position lights  
The position lights help to alert other road users to the presence of your car. You can leave the car locked  
with the position lights on.  
The position lights are useful when you need to make other road users aware of your position, such as when you intend to  
leave the car stationary for a short period of time.  
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
206 / 396  
Press the car symbol  
in the bottom bar and go to Settings.  
1
Go to Controls → Lights and displays → Exterior lights.  
2
3
4
Press the position lights symbol  
.
Confirm your selection by pressing the OK button  
The position lights are turned on.  
on the steering wheel.  
>
The position lights are turned off by selecting a different primary lighting mode.  
9.1.1.6. Hazard warning lights  
If there is a potential risk to surrounding traffic, you should turn the hazard lights on. This helps to alert other  
road users of the need for greater awareness.  
Important  
It is the driver's responsibility to use hazard lights according to local laws and traffic regulations.  
The hazard lights button is located in the overhead console. You can also access the lights in the bottom bar in the display.  
The location of the hazard lights button in the overhead console  
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
207 / 396  
The location of the hazard lights button in the display  
The status and interaction points to control the hazard lights are signified by the associated symbol.  
Automatic activation  
The hazard warning lights turn on automatically when the emergency brake lights are triggered due to sudden braking. You can  
them off manually or let them turn off automatically when you begin driving again.  
In the event of a collision  
Your hazard lights will automatically turn on in the event of a collision.[1]  
There is a cool-down period which disables the option to turn the hazard lights off. When you can use them as normal, the haz-  
ard lights button begins flashing again.  
[1]  
This is dependent on local regulations and regional standards.  
9.1.1.6.1. Activating the hazard warning lights  
The hazard warning lights are essential for driving safety. Be sure that you know how to work them.  
Hazard warning lights symbol  
When you get into the car, the hazard warning lights button in the overhead console lights up, showing that you can use it.  
There's also a button located in the bottom bar in the display.  
Press the hazard warning lights button, either in the overhead console or the display.  
1
Both of the direction indicator symbols in the driver information area of the display and the hazard warning lights buttons  
>
flash simultaneously in the same rhythm as the lights. You will also hear a ticking sound.  
9.1.1.7. Adjusting headlights height  
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
208 / 396  
You can adjust the height of the front headlights.  
Changing the vertical tilt of the passing beam allows you to control how far ahead the beam will illuminate. You can use the  
headlights' height adjustment to counteract any changes to the car's balance. Keep in mind that high-angled beams can dazzle  
other road users.  
Press the car symbol  
in the bottom bar and go to Settings.  
1
Go to Controls → Lights and displays → Exterior lights → Adjust height of light beam.  
The height adjustment page opens.  
2
>
Select the height you want.  
3
4
Confirm your selection by pressing the OK button  
on the steering wheel.  
9.1.2. Operating the direction indicators  
Use the direction indicators to communicate how you intend to manoeuvre your car. The controls are located  
on the left-hand steering wheel stalk.  
The indicators have two types of activation – quick and standard. While the indicators are blinking, you will hear a ticking sound  
and see a direction indicator symbol in the driver information area of the display.  
The indicators on the left-hand stalk  
Quick indication  
Move the left-hand steering wheel stalk slightly up or down and allow it to spring back to the middle.  
1
The indicators blink three times before turning off.  
>
Standard indication  
Move the left-hand steering wheel stalk up to turn the right indicator on and down to turn the left direction indicator on.  
2
The content of this manual represents the status of the user manual at the time of printing and may not be completely valid in future  
instances. For more information, refer to the first page for the complete disclaimer note.  
209 / 396  

Related Topics

Visibility, mirrors and exterior lights
Exterior lights Operating the driving lights High beam Passing beam Activating the passing beam Activating the rear fog light Activating the position lights Hazard warning lights Activating the hazard warning lights Adjusting headlights height Exterior convenience lights Activating the guidance light Welcome lights Enabling the welcome lights Mirrors Adjusting wing mirrors Wipers and washers Controlling front wipers Controlling rear wiper Activating washers

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot