Driver assist systems -> Speed limiter for Your Volkswagen ID.7 4 Door First Generation (2023-2025)

(→ Vehicle care).  
The sensor areas are obstructed by add-on parts, number plate holders with trim frames or stickers. Keep the area  
around the sensors clear (→ Accessories and replacement parts).  
The sensors have been displaced or damaged, for example due to damage to the front of the vehicle or the  
windscreen. Check whether damage is visible (→ Accessories and replacement parts).  
Paint work or structural modifications were carried out on the front of the vehicle or windscreen (→ Repairs and  
technical modifications).  
Fault or malfunction. Deactivate and reactivate the vehicle’s drive system.  
If the problem persists, go to a correspondingly qualified workshop. Volkswagen recommends using a Volkswagen  
dealership.  
If the sensor visibility is restricted, driver assist systems may not be available or may be available only to a  
limited extent. Observe any other indicator lamps of the driver assist systems (→ Symbols in the instrument  
cluster).  
Depending on the malfunction, additional information may be displayed in the vehicle status (→ Vehicle  
settings menu).  
Introduction to the topic  
The speed limiter helps to prevent the vehicle from exceeding a speed that you have stored.  
Speed range  
The speed limiter is available when driving forwards at speeds from around 30 km/h(around 20 mph).  
Driving with the speed limiter  
You can interrupt the speed limiter function at any time by fully depressing the accelerator beyond the point of  
resistance. As soon as the stored speed is exceeded, the green indicator lamp will flash and an acoustic warning may  
sound. The speed remains stored in the memory.  
The speed limiter function is activated again automatically as soon as the speed drops below the stored speed.  
Displays  
When the speed limiter is switched on, the instrument cluster display shows the stored speed and the status of the  
speed limiter.  
The following indicator lamps light up, depending on the driving situation:  
Speed limiter switched on, system control active.  
Speed limiter switched on, system control not active.  
Driving downhill  
The vehicle cannot maintain the stored speed in all driving situations. Always be prepared to brake the vehicle.  
1. Use the brake energy recuperation of the electric drive on extended downhill stretches.  
This will relieve the load on the brakes.  
WARNING  
Use of the speed limiter in adverse weather conditions is dangerous and can cause accidents and serious injuries or  
228  
 
even death.  
Ensure that your speed is always appropriate for the current visibility, weather and road/traffic conditions. The  
driver is responsible for the vehicle speed at all times.  
Do not drive at full throttle if this is not necessary.  
Never use the speed limiter on slippery roads(e.g. as a result of aquaplaning, snow, ice or leaves).  
In order to avoid unintentional control interventions, switch off the speed limiter when you do not need it.  
Operating the speed limiter  
Fig. 1 Left-hand side of the multifunction steering wheel.  
Switching on  
1. Press the  
is selected.  
button on the left-hand side of the multifunction steering wheel repeatedly until the speed limiter  
button on the right-hand side of the multifunction steering wheel or wait for a short time.  
2. Press the  
The speed limiter is switched on. The system is not yet active.  
Starting control  
1. While driving, press the  
button.  
The current speed is stored as the maximum speed.  
Adjusting the speed  
You can adjust the stored speed:  
+ 1 km/h (1 mph):  
Gently press the button.  
- 1 km/h (1 mph):  
Gently press the button.  
+ 10 km/h (5 mph):  
Strongly press the button or swipe over the button from bottom to top. The first time it is pressed, it jumps to  
the next higher ten (km/h) or five (mph) increment.  
- 10 km/h (5 mph):  
Strongly press the button or swipe over the button from top to bottom. The first time it is pressed, it jumps  
to the next lower ten (km/h) or five (mph) increment  
229  
 
Press and hold the corresponding button to continuously change the stored speed.  
Cancelling control  
1. Briefly press the  
button.  
The speed remains stored in the memory.  
Resuming control  
1. Press the  
button.  
Troubleshooting  
Speed limiter not available  
Fault or malfunction. The indicator lamp lights up yellow.  
1. Deactivate and reactivate the vehicle’s drive system.  
2. If the problem persists, switch off the speed limiter and go to a correspondingly qualified workshop.  
Volkswagen recommends using a Volkswagen dealership.  
Control is interrupted automatically  
ESC  
is switched off.  
The brakes have overheated. Allow the brakes to cool down and check their functionality again.  
If the problem persists, switch off the speed limiter and go to a correspondingly qualified workshop. Volkswagen  
recommends using a Volkswagen dealership.  
For safety reasons, the speed limiter switches itself off completely only when you release the accelerator once or  
switch off the system manually.  
230