Navigation -> 360? range display for Your Volkswagen ID.7 4 Door First Generation (2023-2025)

Selecting on the map  
The navigation map contains active areas at many locations which are suitable for destination input. To enter a  
destination, tap the desired position or location on the map. You can start route guidance if map data is available at  
this location.  
Destination input via the navigation map depends on the data status and is not possible for all positions.  
Use the off-road navigation function to enter a destination point with unknown data.  
Off-road navigation  
The off-road navigation function calculates routes to selected destination points with unknown data. If a destination  
point is not on known roads or there is no positioning data available for this point, the navigation system will  
calculate the route up to the nearest point on the known roads and then complete the route up to the destination  
point by a direct connection.  
To start off-road navigation, tap a free area without positioning data.  
Starting navigation  
1. Tap  
.
2. Move the map view until the desired position can be selected. The navigation map can be operated by extended  
tap gestures (→ Navigation).  
3. Tap the desired destination or any destination point on the map without positioning data.  
4. Tap Start.  
Or: tap  
.
Using the address data of a contact  
Start navigation using the stored address data of a contact. Stored contacts without address data cannot be used for  
route guidance.  
Starting navigation  
1. Tap  
.
2. Tap the desired contact and address data.  
3. Tap Start.  
Or: tap  
.
NOTICE  
If the address data of a contact is out-of-date, navigation will still be performed to the stored address. Make sure  
that the address of the contact is up-to-date.  
360° range display  
The 360° range display shows the possible range with the current charge level of the high-voltage battery. The  
display shows only an estimated range calculated on the basis of the current consumption figures. The display may  
change during the journey, and the figures shown in the margins must also be taken as an estimate.  
Activating or deactivating the 360° range display  
1. Tap and activate  
Show range on map.  
398  
 
To show the complete range display on the map, you may need to adjust the map view  
(→ Navigation).  
A range warning can also be activated in the navigation settings: tap and activate  
routes Range warning.  
Route guidance &  
Electric Vehicle Route Planner  
The Electric Vehicle Route Planner can be used to automatically add charging stations located on the currently  
selected route as charging stops. A maximum of ten charging stations can be automatically added as charging stops.  
Charging stops can be added and set with different preferences:  
Payment method.  
Remaining range at the charging stop and at the destination.  
Defining preferences  
1. Tap and activate  
Route guidance & routes Route options.  
2. Tap Add charging stopovers automatically.  
3. Set the desired remaining range.  
Or: set the desired payment method.  
Depending on the selection and the available data, suitable charging stations will be prioritised in the route plan.  
If your preferred payment method is not available at one or more charging stations, an acoustic message will  
be played.  
The settings for the upper battery charge limit in theCharging menu may be overwritten temporarily by the “Electric  
Vehicle Route Planner” function (→ Charging settings).  
The settings for the upper battery charge limit in theCharging menu will be used again after the end of route  
guidance.  
The current occupancy status of the charging stations is displayed in the Infotainment system when an internet  
connection is available (→ Navigation). The current status is indicated by a coloured dot at the edge of the edge of  
the symbol.  
Adding charging stops automatically  
1. To activate automatic planning of necessary charging stations on the route, tap and activate  
guidance & routes Route options Add charging stopovers automatically.  
Route  
Selecting alternative charging stations  
Instead of the automatically planned charging stations, you can also select alternative charging stations for the  
planned routes.  
1. Enter or select the desired destination.  
2. Tap Start.  
3. Open the route plan.  
4. Tap a planned charging station in the route plan.  
Details of the planned charging station are displayed.  
5. Tap Show more charging stations.  
The locations of additional nearby charging stations will be shown on the map.  
399