Advertisement

Advertisement

Breakdown assistance -> Introduction (Breakdown set) for Your Volkswagen Transporter Van Seventh Generation (2021-2025)

serious injuries.  
Always keep all wheel bolts and threads in the wheel hubs clean and free from oil and grease. The wheel bolts  
must be easy to turn and be tightened to the specified torque.  
After changing a wheel, the indicator lamp for the tyre monitoring system may indicate a fault in the system  
(→ Tyre Pressure Loss Indicator).  
Introduction  
In some countries, the vehicle may be supplied with a breakdown set.  
You can use the breakdown set(tyre mobility set) to safely seal any tyre damage caused by foreign bodies or  
punctures up to 4 mm (5/32 inches) in diameter. Do not remove foreign objects (e.g. screws or nails) from the tyre!  
Once the sealant has been added to the tyre, the tyre pressure must be checked and adjusted again after  
approximately 10 minutes of driving.  
The breakdown set is only designed to fill one tyre. Seek assistance from a correspondingly qualified workshop if  
more than one vehicle tyre is damaged.  
Only use the breakdown set when the vehicle has been safely parked and you are familiar with the work and safety  
precautions needed! Otherwise, seek assistance from a suitably qualified workshop.  
The tyre sealant must not be used in the following situations:  
If the rim is damaged.  
If the outside temperature is below -20°C(-4°F).  
If there are cuts or punctures in the tyre that are larger than 4 mm(5/32 in).  
If the vehicle was driven with very low tyre pressure or a flat tyre.  
If the use-by date on the tyre filler bottle has expired.  
If a foreign object has been removed from the tyre.  
In connection with mobility tyres. The word “Seal” is on the outer wall of the tyre if your vehicle is fitted with  
mobility tyres.  
WARNING  
Using the breakdown set can be dangerous, especially if the tyre is inflated at the roadside. Please note the  
following steps in order to reduce the risk of serious injuries:  
Stop the vehicle as soon as it is possible and safe to do so. To inflate the tyre, park the vehicle at a safe distance  
from moving traffic (→ In an emergency).  
Make sure that the surface the vehicle is parked on is level and firm.  
All passengers, and children in particular, must be at a safe distance and away from your area of work.  
Switch on the hazard warning lights to warn other road users.  
Only use the breakdown set when the vehicle has been safely parked and you are familiar with the work and  
safety precautions needed! Otherwise, seek assistance from a suitably qualified workshop.  
Tyres repaired with the breakdown set are intended for temporary, emergency use only. They should be used only  
until you can reach the nearest qualified workshop.  
Tyres that have been repaired using the breakdown set should be replaced as soon as possible.  
If your skin comes into contact with the sealant, wipe it off immediately. The sealant poses a health hazard.  
Keep the breakdown set out of the reach of children.  
When using the breakdown set, never lift the vehicle with a jack, even if the jack is approved for the vehicle.  
WARNING  
Tyres that have been filled with sealant will not handle in the same way as a standard tyre.  
Never drive faster than 80 km/h(50 mph).  
547  
Do not accelerate quickly, brake suddenly or drive at high speed through bends.  
Drive at a maximum of 80 km/h(50 mph) for 10 minutes only and then check the tyre.  
Dispose of used or out-of-date sealant in accordance with legal  
requirements.  
You can purchase a new tyre filler bottle from a correspondingly qualified  
workshop.  
Observe the separate operating instructions provided by the manufacturer of the breakdown  
set.  
Contents of the breakdown set  
Fig. 1 Diagram: Components in the breakdown set.  
The breakdown set consists of the following components:  
1
2
3
4
5
Sticker with the maximum permitted speed “max. 80 km/h” or “max. 50 mph”.  
Filler hose with plug.  
Tyre filler bottle.  
Spare valve core.  
Valve core extractor.  
5
There is a slot on the lower end of the valve core extractor→ Fig. 1  
for the valve core. This is required for  
4
extracting and fitting the tyre valve core. This also applies to the spare valve core  
.
548