Get Mobility Guide for BMW M3 4 Door Fifth Generation (2014-2019)

Mobility

In order to always ensure your mobility, you will

find important information on operating fluids,

wheels and tires, maintenance and Roadside

Assistance in the following.

Mobility

Refueling

Vehicle features and options

Fuel cap

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Opening

1. Briefly press the rear edge of the fuel filler

flap.

General information

Observe the fuel recommendation, refer to

page 178, prior to refueling.

2. Turn the fuel cap counterclockwise.

Safety information

NOTE

With a range of less than 30 miles/50 km

it is possible that the engine will no longer have

sufficient fuel. Engine functions are not en‐

sured anymore. There is a risk of property

damage. Refuel promptly.◀

3. Place the fuel cap in the bracket attached

to the fuel filler flap.

176

Refueling

Mobility

Closing

WARNING

The retaining strap of the fuel cap can be

jammed and crushed during closing. The cap

cannot be correctly closed. Fuel or fuel vapors

can escape. There is a risk of injury or risk of

property damage. Pay attention that the retain‐

ing strap is not jammed or crushed when clos‐

ing the lid.◀

1. Fit the cap and turn it clockwise until you

clearly hear a click.

2. Close the fuel filler flap.

Manually unlocking fuel filler flap

E.g., in the event of an electrical malfunction.

Have fuel filler flap unlocked by a dealer’s serv‐

ice center or another qualified service center or

repair shop.

Observe the following when

refueling

General information

The fuel tank is full when the filler nozzle clicks

off the first time.

Observe safety regulations posted at the gas

station.

Safety information

NOTE

Fuels are toxic and aggressive. Overfill‐

ing of the fuel tank can damage the fuel sys‐

tem. Painted surfaces may be damaged by

contact with fuel. Escaping fuel can harm the

environment. There is a risk of property dam‐

age. Avoid overfilling.◀

177

Mobility

Fuel

Safety information

Vehicle features and options

NOTE

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Do not press the Start/Stop button after

refueling with the wrong fuel. Furthermore, the

catalytic converter is permanently damaged.

There is a risk of property damage. Do not re‐

fuel or add the following in the case of gasoline

engines:

▷

Leaded gasoline.

Metallic additives, e.g., manganese or iron.

Do not press the Start/Stop button after refuel‐

ing with the wrong fuel. Contact a dealer’s

service center or another qualified service cen‐

ter or repair shop.◀

Fuel recommendation

General information

Depending on the region, many gas stations

sell fuel that has been customized to winter or

summer conditions. Fuel that is available in

winter, e.g., helps make a cold start easier.

NOTE

Incorrect fuels can damage the fuel sys‐

tem and the engine. There is a risk of damage

to property. Do not use fuels with a higher per‐

centage of ethanol than recommended. Do not

refuel with fuels containing methanol, e.g. M5

to M100.◀

Gasoline

General information

NOTE

For the best fuel efficiency, the gasoline

should be sulfur-free or very low in sulfur con‐

tent.

Fuel that does not comply with the mini‐

mum quality can compromise engine function

or cause engine damage. There is a risk of

property damage. Do not fill with fuel that does

not comply with the minimum quality.◀

Fuels that are marked on the gas pump as con‐

taining metal must not be used.

Fuels with a maximum ethanol content of

10 %, i. e., E10, may be used for refueling.

CAUTION

Ethanol should meet the following quality

standards:

The use of poor-quality fuels may result

in harmful engine deposits or damage. Addi‐

tionally, problems relating to drivability, start‐

ing and stalling, especially under certain envi‐

ronmental conditions such as high ambient

temperature and high altitude, may occur.

US: ASTM 4806–xx

CAN: CGSB-3.511–xx

xx: comply with the current standard in each

case.

If drivability problems are encountered, we rec‐

ommend switching to a high quality gasoline

brand and a higher octane grade — AKI num‐

ber — for a few tank fills. To avoid harmful en‐

178

Fuel

Mobility

gine deposits, it is highly recommended to

purchase gasoline from Top Tier retailers.

Failure to comply with these recommendations

may result in the need for unscheduled main‐

tenance.◀

Recommended fuel grade

BMW recommends AKI 93.

Minimum fuel grade

BMW recommends AKI 91.

If you use gasoline with this minimum AKI Rat‐

ing, the engine may produce knocking sounds

when starting at high outside temperatures.

This has no effect on the engine life.

179

Mobility

Wheels and tires

The displays of inflation devices may under-

read by up to 0.1 bar/2 psi.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Tires have a natural, consistent loss of tire in‐

flation pressure.

For Tire Pressure Monitor: perform a reset of

the Tire Pressure Monitor after adjusting tire

pressure to a new value.

Tire inflation pressure specifications

The tire inflation pressure table, refer to

page 181, contains all tire inflation pressure

specifications for the specified tire sizes at the

ambient temperature. The tire inflation pres‐

sure values apply to tire sizes approved by the

manufacturer of the vehicle for the vehicle

type.

Tire inflation pressure

General information

The tire characteristics and tire inflation pres‐

sure influence the following:

To identify the correct tire inflation pressure,

please note the following:

▷

The service life of the tires.

Road safety.

▷

Tire sizes of your vehicle.

Maximum permitted driving speed.

Driving comfort.

Tire inflation pressures up to

100 mph/160 km/h

For speeds of up to 100 mph/160 km/h and for

optimum driving comfort, note the pressure

values in the tire inflation pressure table, refer

to page 181, and adjust as necessary.

Safety information

WARNING

A tire with low or missing tire inflation

pressure impacts handling, such as steering

and braking response. There is a risk of an ac‐

cident. Regularly check the tire inflation pres‐

sure, and correct it as needed, e.g., twice a

month and before a long trip.◀

Checking the tire inflation pressure

Only check the tire inflation pressure when the

tires are cold. This means after driving no more

than 1.25 miles/2 km or when the vehicle has

been parked for at least 2 hours.

Tires heat up while driving, and the tire infla‐

tion pressure increases along with the tire's

temperature. The tire inflation pressure speci‐

fications relate to cold tires or tires at ambient

temperature.

These pressure values can also be found on

the tire inflation pressure label on the driver's

door pillar.

Do not exceed a speed of 100 mph/160 km/h.

180

Wheels and tires

Mobility

values in the tire inflation pressure table, refer

to page 181, and adjust as necessary.

Tire inflation pressure values up to

100 mph/160 km/h

M3

Tire inflation pressure values over

100 mph/160 km/h

Tire size

Pressure specifications in

bar/PSI

M3

Specifications

in bar/PSI with

cold tires

Tire size

Pressure specifications in

bar/PSI

Specifications

in bar/PSI with

cold tires

255/40 R 18 99 2.2 / 31

V M+S XL

2.3 / 33

2.6 / 37

-

255/35 R 19 96 2.4 / 34

V M+S XL

255/40 R 18 99 2.5 / 36

V M+S XL

2.8 / 40

3.2 / 46

-

Front: 255/40 R 2.2 / 31

18 95 (Y)

255/35 R 19 96 2.9 / 42

V M+S XL

Rear: 275/40 R

18 99 (Y)

-

2.2 / 31

-

Front: 255/40 R 2.4 / 34

18 95 (Y)

Front: 255/35 R 2.2 / 31

19 92 (Y)

Rear: 275/40 R

18 99 (Y)

-

2.4 / 34

-

Rear: 275/35 R

19 100 (Y) XL

-

2.2 / 31

-

Front: 255/35 R 2.4 / 34

19 92 (Y)

F: 265/30 R 20 2.2 / 31

94 (Y) XL

Rear: 275/35 R

19 100 (Y) XL

-

2.6 / 37

-

Rear: 285/30 R

20 99 (Y) XL

-

2.2 / 31

F: 265/30 R 20 2.7 / 39

94 (Y) XL

Rear: 285/30 R

20 99 (Y) XL

-

2.9 / 42

Tire inflation pressures at max.

speeds above 100 mph/160 km/h

WARNING

In order to drive at maximum speeds in

excess of 100 mph/160 km/h, please observe,

and, if necessary, adjust tire pressures for

speeds exceeding 100 mph/160 km/h from the

relevant table on the following pages. Other‐

wise, tire damage and accidents could occur.◀

Tire identification marks

Tire size

245/45 R 18 96 Y

245: nominal width in mm

45: aspect ratio in %

R: radial tire code

For speeds over 100 mph/160 km/h and for

optimum driving comfort, note the pressure

181

Mobility

Wheels and tires

18: rim diameter in inches

Uniform Tire Quality Grading

96: load rating, not for ZR tires

Y: speed rating, before the R on ZR tires

Quality grades can be found where applicable

on the tire sidewall between tread shoulder

and maximum section width.

E.g.: Treadwear 200; Traction AA; Tempera‐

ture A

Maximum tire load

Maximum tire load is the maximum permissible

weight for which the tire is approved.

DOT Quality Grades

Treadwear

Locate the maximum tire load on the tire side‐

wall and the Gross Axle Weight Rating – GAWR

– on the certification label on the driver’s door

pillar.

Traction AA A B C

Temperature A B C

Divide the tire load by 1.1. It must be greater

than one-half of the vehicle’s Gross Axle

Weight Rating – GAWR. Note, front vs. rear

GAWR and tire loads, respectively.

All passenger vehicle tires must conform to

Federal Safety Requirements in addition to

these grades.

Treadwear

Speed letter

The treadwear grade is a comparative rating

based on the wear rate of the tire when tested

under controlled conditions on a specified gov‐

ernment test course. E.g., a tire graded 150

would wear one and one-half, 1 g, times as well

on the government course as a tire graded

100. The relative performance of tires depends

upon the actual conditions of their use, how‐

ever, and may depart significantly from the

norm due to variations in driving habits, service

practices and differences in road characteris‐

tics and climate.

Q = up to 100 mph, 160 km/h

R = up to 106 mph, 170 km/h

S = up to 112 mph, 180 km/h

T = up to 118 mph, 190 km/h

H = up to 131 mph, 210 km/h

V = up to 150 mph, 240 km/h

W = up to 167 mph, 270 km/h

Y = up to 186 mph, 300 km/h

Tire Identification Number

DOT code: DOT xxxx xxx 3816

xxxx: manufacturer code for the tire brand

xxx: tire size and tire design

3816: tire age

Traction

The traction grades, from highest to lowest,

are AA, A, B, and C.

Those grades represent the tire's ability to

stop on wet pavement as measured under

controlled conditions on specified government

test surfaces of asphalt and concrete. A tire

marked C may have poor traction performance.

Tires with DOT codes meet the guidelines of

the U.S. Department of Transportation.

Tire age

The traction grade assigned to this tire is

based on straight-ahead braking traction tests,

and does not include acceleration, cornering,

hydroplaning, or peak traction characteristics.

DOT … 3816: the tire was manufactured in the

38th week of 2016.

Recommendation

Regardless of wear and tear, replace tires at

least every 6 years.

182

Wheels and tires

Mobility

Temperature

Minimum tread depth

The temperature grades are A, the highest, B,

and C, representing the tire's resistance to the

generation of heat and its ability to dissipate

heat when tested under controlled conditions

on a specified indoor laboratory test wheel.

Sustained high temperature can cause the ma‐

terial of the tire to degenerate and reduce tire

life, and excessive temperature can lead to

sudden tire failure. The grade C corresponds

to a level of performance which all passenger

vehicle tires must meet under the Federal Mo‐

tor Vehicle Safety Standard No. 109. Grades

Band A represent higher levels of performance

on the laboratory test wheel than the minimum

required by law.

Wear indicators are distributed around the

tire's circumference and have the legally re‐

quired minimum height of 0.063 in‐

ches/1.6 mm.

They are marked on the side of the tire with

TWI, Tread Wear Indicator.

WARNING

The temperature grade for this tire is es‐

tablished for a tire that is properly inflated and

not overloaded. Excessive speed, underinfla‐

tion, or excessive loading, either separately or

in combination, can cause heat buildup and

possible tire failure.◀

Tire damage

General information

Inspect your tires regularly for damage, foreign

objects lodged in the tread, and tread wear.

Driving over rough or damaged road surfaces,

as well as debris, curbs and other obstacles

can cause serious damage to wheels, tires and

suspension parts. This is more likely to occur

with low-profile tires, which provide less cush‐

ioning between the wheel and the road. Be

careful to avoid road hazards and reduce your

speed, especially if your vehicle is equipped

with low-profile tires.

M+S

Winter and all-season tires with better cold

weather performance than summer tires.

Tire tread

Summer tires

Do not drive with a tire tread depth of less than

0.12 inches/3 mm.

Indications of tire damage or other vehicle mal‐

functions:

There is an increased risk of hydroplaning if

the tire tread depth is less than 0.12 in‐

ches/3 mm.

▷

Unusual vibrations while driving.

Unusual handling such as a strong ten‐

dency to pull to the left or right.

Winter tires

Do not drive with a tire tread depth of less than

0.16 inches/4 mm.

Damage can, e.g., be caused by driving over

curbs, road damage, or similar things.

Below a tread depth of 0.16 inches/4 mm, tires

are less suitable for winter operation.

183

Mobility

Wheels and tires

Safety information

WARNING

Damaged tires can lose tire inflation

pressure, which can lead to loss of vehicle

control. There is a risk of an accident. If tire

damage is suspected while driving, immedi‐

ately reduce speed and stop. Have wheels and

tires checked. For this purpose, drive carefully

to the nearest dealer’s service center or an‐

other qualified service center or repair shop.

Have vehicle towed or transported as

needed.◀

Wheels and tires which are not suitable

for your vehicle can damage parts of the vehi‐

cle, for instance due to contact with the body

due to tolerances despite the same official size

rating. There is a risk of an accident. The man‐

ufacturer of your vehicle strongly suggests

that you use wheels and tires that have been

recommended by the vehicle manufacturer for

your vehicle type.◀

Recommended tire brands

WARNING

Damaged tires can lose tire inflation

pressure, which can lead to loss of vehicle

control. There is a risk of an accident. Do not

repair damaged tires, but have them re‐

placed.◀

Changing wheels and tires

For each tire size, BMW recommends certain

tire brands. These can be identified by a star

on the tire sidewall.

Mounting

Have mounting and wheel balancing carried

out by a dealer’s service center or another

qualified service center or repair shop.

New tires

Wheel and tire combination

General information

You can ask the dealer’s service center or an‐

other qualified service center or repair shop

about the correct wheel/tire combination and

wheel rim versions for the vehicle.

Tire traction is not optimal due to manufactur‐

ing circumstances when tires are brand-new;

they achieve their full traction potential after a

break-in time.

Drive conservatively for the first

200 miles/300 km.

Retreaded tires

The manufacturer of your vehicle does not rec‐

ommend the use of retreaded tires.

Incorrect wheel and tire combinations impair

the function of a variety of systems such as

ABS or DSC.

To maintain good handling and vehicle re‐

sponse, use only tires with a single tread con‐

figuration from a single manufacturer.

WARNING

Retreaded tires can have different tire

casing structures. With advanced age the serv‐

ice life can be limited. There is a risk of an acci‐

Following tire damage, have the original wheel

and tire combination remounted on the vehicle

as soon as possible.

184

Wheels and tires

Mobility

dent. The manufacturer of your vehicle does

not recommend the use of retreaded tires.◀

Repairing a flat tire

Safety measures

Winter tires

Winter tires are recommended for operating on

winter roads.

▷

Park the vehicle as far away as possible

from passing traffic and on solid ground.

▷

Switch on the hazard warning system.

Although so-called all-season M+S tires pro‐

vide better winter traction than summer tires,

they do not provide the same level of perform‐

ance as winter tires.

Secure the vehicle against rolling away by

setting the parking brake.

▷

Have all vehicle occupants get out of the

vehicle and ensure that they remain out‐

side the immediate area in a safe place,

such as behind a guardrail.

Maximum speed of winter tires

If the maximum speed of the vehicle is higher

than the permissible speed for the winter tires,

then attach a corresponding information label/

sticker in the field of view. The label is available

from a dealer’s service center or another quali‐

fied service center or repair shop.

▷

If necessary, set up a warning triangle or

portable hazard warning light at a sufficient

distance.

Change wheels only on a flat, solid and

slip-resistant surface. On soft or slippery

ground, for example snow, ice, tiles, etc.,

the vehicle or the vehicle jack may slip

away sideways.

With mounted winter tires, observe and adhere

to the permissible maximum speed.

▷

Do not place wood blocks or similar items

under the vehicle jack; otherwise, it cannot

reach its carrying capacity because of the

restricted height.

Rotating wheels between axles

The manufacturer of your vehicle advises

against switching wheels between the front

and rear axles. This can impair the handling

characteristics.

If the vehicle is raised, do not lie under the

vehicle and do not start the engine, or else

there is a danger to life.

Rotating the tires between the axes is not per‐

missible on vehicles with different tire sizes or

rim sizes on the front and rear axles.

Mobility System

Storage

Store wheels and tires in a cool, dry and dark

place.

Concept

With the Mobility System, minor tire damage

can be sealed temporarily to enable continued

travel. To accomplish this, sealant is pumped

into the tires, which seals the damage from the

inside.

Always protect tires against all contact with oil,

grease and fuels.

Do not exceed the maximum tire inflation pres‐

sure indicated on the side wall of the tire.

The compressor can be used to check the tire

inflation pressure.

185

Mobility

Wheels and tires

General information

Compressor

▷

Follow the instructions on using the Mobi‐

lity System found on the compressor and

sealant container.

Use of the Mobility System may be ineffec‐

tive if the tire puncture measures approx.

1/8 inches/4 mm or more.

Contact a dealer’s service center or an‐

other qualified service center or repair

shop if the tire cannot be made drivable.

1

2

3

4

5

6

7

Holder for sealant container

▷

If possible, do not remove foreign bodies

that have penetrated the tire.

Compressor

Pull the speed limit sticker off the sealant

container and apply it to the steering

wheel.

Connector/cable for socket

Connection hose

On/off switch

▷

The use of a sealant can damage the TPM

wheel electronics. In this case, have the

electronics checked and replaced at the

next opportunity.

Inflation pressure dial

Reduce inflation pressure

Filling the tire with sealant

1. Shake the sealant container.

Storage

The Mobility System is located under the

cargo floor panel.

Sealant container

2. Pull the connection hose fully out of the

compressor housing. Do not kink the hose.

▷

Sealant container, arrow 1.

Filling hose, arrow 2.

Observe use-by date on the sealant container.

186

Wheels and tires

Mobility

3. Screw the connection hose onto the con‐

nector of the sealant container.

6. With the compressor switched off, insert

the plug into the power socket inside the

vehicle.

4. Insert the sealant container on the com‐

pressor housing in an upright position.

7. With the ignition turned on or the engine

running, switch on the compressor.

5. Screw the filling hose of the sealant con‐

tainer onto the tire valve of the nonworking

wheel.

DANGER

If the exhaust pipe is blocked or ventila‐

tion is insufficient, harmful exhaust gases can

enter into the vehicle. The exhaust gases con‐

tain carbon monoxide, an odorless and color‐

less but highly toxic gas. In enclosed areas, ex‐

haust gases can also accumulate outside of

the vehicle. There is danger to life. Keep the

exhaust pipe free and ensure sufficient ventila‐

tion.◀

NOTE

The compressor can overheat during ex‐

tended operation. There is a risk of property

damage. Do not run the compressor for more

than 10 min.◀

Let the compressor run for approx. 3 to 8 mi‐

nutes to fill the tire with sealant and achieve a

tire inflation pressure of approx. 2.5 bar.

187

Mobility

Wheels and tires

While the tire is being filled with sealant, the

tire inflation pressure may sporadically reach

approx. 5 bar. Do not switch off the compres‐

sor at this point.

Correcting the tire inflation pressure

1. Stop at a suitable location.

2. Screw the connection hose of the com‐

pressor directly onto the tire valve stem.

If a tire inflation pressure of 2 bar is not

reached:

3. Insert the connector into the power socket

inside the vehicle.

1. Switch off the compressor.

4. Correct the tire inflation pressure to

2.5 bar.

2. Unscrew the filling hose from the wheel.

3. Drive 33 ft/10 m forward and back to dis‐

tribute the sealant in the tire.

▷

Increase pressure: with the ignition

turned on or the engine running, switch

on the compressor.

4. Inflate the tire again using the compressor.

▷

To reduce the pressure: press the but‐

ton on the compressor.

If a tire inflation pressure of 2 bar cannot be

reached, contact your dealer’s service cen‐

ter or another qualified service center or

repair shop.

Continuing the trip

Do not exceed the maximum permissible

speed of 50 mph/80 km/h.

Stowing the Mobility System

1. Unscrew the filling hose of the sealant con‐

tainer from the wheel.

Reinitialize the Tire Pressure Monitor.

Replace the nonworking tire and the sealant

container of the Mobility System promptly.

2. Unscrew the connection hose of the com‐

pressor from the sealant container.

3. Connect the filling hose of the sealant con‐

tainer previously connected to the tire

valve with the available connector on the

sealant container.

Snow chains

Fine-link snow chains

The manufacturer of your vehicle recommends

use of fine-link snow chains. Certain types of

fine-link snow chains have been tested by the

manufacturer of the vehicle and recommended

as road-safe and suitable.

This prevents leftover sealant from escap‐

ing from the container.

4. Wrap the empty sealant container in suita‐

ble material to avoid dirtying the cargo

area.

Information regarding suitable snow chains is

available from a dealer’s service center or an‐

other qualified service center or repair shop.

5. Stow the Mobility System back in the vehi‐

cle.

Distributing the sealant

Use

Immediately drive approx. 5 miles/10 km to en‐

sure that the sealant is evenly distributed in the

tire.

WARNING

With the mounting of snow chains on un‐

suitable tires, the snow chains can come into

contact with vehicle parts. There is a risk of ac‐

cidents or risk of property damage. Only mount

snow chains on tires that are designated by

Do not exceed a speed of 50 mph/80 km/h.

If possible, do not drive at speeds less than

12 mph/20 km/h.

188

Wheels and tires

Mobility

their manufacturer as suitable for the use of

snow chains.◀

jammed or damaged. There is a risk of injury

and risk of damage to property. Only use the

jack to attach an emergency or spare wheel in

the event of a breakdown.◀

Use only in pairs on the rear wheels, equipped

with the tires of the following size:

WARNING

▷

255/40 R 18.

255/35 R 19.

On soft or slippery ground, e.g., snow,

ice, tiles, etc., the vehicle jack can slip away.

There is a risk of injury. If possible, change the

tire/wheel on a flat, solid and slip-resistant sur‐

face.◀

Follow the snow chain manufacturer's instruc‐

tions.

Make sure that the snow chains are always

sufficiently tight. Re-tighten as needed ac‐

cording to the snow chain manufacturer's in‐

structions.

WARNING

The vehicle jack is only provided for

short-term lifting of the vehicle for wheel

changes. Even if all safety measures are ob‐

served, there is a risk of the raised vehicle fall‐

ing, if the vehicle jack tilts over. There is a risk

of injuries or danger to life. If the vehicle is

raised, do not lie under the vehicle and do not

start the engine.◀

Do not initialize the Tire Pressure Monitor after

mounting snow chains, as doing so may result

in incorrect readings.

When driving with snow chains, if needed,

briefly activate M Dynamic Mode.

Maximum speed with snow chains

Do not exceed a speed of 30 mph/50 km/h

when using snow chains.

WARNING

The vehicle jack is optimized for lifting

the vehicle and for the jacking points on the

vehicle only. There is a risk of injury. Do not lift

any other vehicle or cargo using the vehicle

jack.◀

Changing wheels/tires

General information

WARNING

When tire sealants are used, an immediate

wheel change when there is a loss of tire infla‐

tion pressure in the event of a flat tire is not al‐

ways necessary.

If the vehicle jack is not inserted into the

jacking point provided for this purpose, the ve‐

hicle may be damaged or the vehicle jack may

slip when it is being cranked up. There is a risk

of injury or risk of damage to property. When

cranking up the vehicle jack, ensure that it is

inserted in the jacking point next to the wheel

housing.◀

If needed, the tools for changing wheels are

available as accessories from a dealer’s service

center or another qualified service center or re‐

pair shop.

Safety information

WARNING

A vehicle that is raised on a vehicle jack

may fall off of the jack if lateral forces are ex‐

erted on it. There is a risk of injury and risk of

damage to property. While the vehicle is

raised, do not exert lateral forces on the vehicle

or pull abruptly on the vehicle. Have a stuck

The jack, issued by the vehicle manufac‐

turer, is provided in order to perform a wheel

change in the event of a breakdown. The jack

is not designed for frequent use; for example,

changing from summer to winter tires.. Using

the jack frequently may cause it to become

189

Mobility

Wheels and tires

wheel removed by a dealer’s service center or

another qualified service center or repair

shop.◀

Preparing the vehicle

▷

Change the wheel as far away as possible

from passing traffic.

▷

Park the vehicle on solid, non-slip and level

ground.

Securing the vehicle against rolling

General information

The vehicle manufacturer recommends to ad‐

ditionally secure the vehicle against rolling

away when changing a wheel.

▷

Switch on the hazard warning system.

Set the parking brake.

Engage a gear or selector lever position P.

As soon as permitted by the traffic flow,

have all vehicle occupants get out of the

vehicle and ensure that they remain out‐

side the immediate area in a safe place,

such as behind a guardrail.

On a level surface

▷

Depending on the equipment version, get

tools and the emergency wheel from the

vehicle.

If necessary, set up a warning triangle or

portable hazard warning lamp at an appro‐

priate distance.

Do not place wood blocks or similar items

under the vehicle jack; otherwise, it cannot

reach its carrying capacity because of the

restricted height.

Place chocks or other suitable objects, for ex‐

ample a rock, in front of and behind the wheel

that is diagonally opposite to the wheel that

you wish to change.

▷

Secure the vehicle additionally against roll‐

ing.

On a slight downhill gradient

Loosen the lug bolts a half turn.

Jacking points for the vehicle jack

If you need to change a wheel on a slight

downhill gradient, place chocks and other suit‐

able objects, for example a rock, under the

wheels of both the front and rear axles against

the rolling direction.

The jacking points for the vehicle jack are lo‐

cated at the indicated positions.

190

Wheels and tires

Mobility

4. Take your hand away from the jack as soon

as the vehicle jack is under load and con‐

tinue turning the crank or lever with one

hand.

Jacking up the vehicle

WARNING

Hands and fingers can be jammed when

using the vehicle jack. There is a risk of injury.

Comply with the described hand position and

do not change this position while using the ve‐

hicle jack.◀

5. Make sure that the vehicle jack foot is ex‐

tended vertically.

1. Hold the vehicle jack with one hand, ar‐

row 1, and grasp the crank with your other

hand, arrow 2.

6. Make sure that the vehicle jack foot stands

vertically and perpendicularly beneath the

jacking point after extending the vehicle

jack.

2. Insert the vehicle jack into the rectangular

recess of the jacking point closest to the

wheel to be changed.

7. Crank up the vehicle jack until the entire

surface of the jack is in contact with the

ground and the wheel in question is raised

a maximum of 1.2 inches/3 cm off the

ground.

3. Extend the vehicle jack by turning the

crank or lever clockwise.

Mounting a wheel

Mount one emergency wheel only.

1. Unscrew the lug bolts and remove the

wheel.

2. Put the new wheel or emergency wheel on

and screw in at least two bolts in a cross‐

wise pattern until hand-tight.

191

Mobility

Wheels and tires

If non-original light-alloy wheels of the ve‐

hicle manufacturer are mounted, the ac‐

companying lug bolts may have to be used

as well.

3. Hand-tighten the remaining lug bolts and

tighten all bolts well in a crosswise pattern.

4. Turn the crank on the vehicle jack counter‐

clockwise to retract the jack and lower the

vehicle.

5. Remove the vehicle jack.

After the wheel change

1. Tighten the lug bolts crosswise. The tight‐

ening torque is 101 lb ft/140 Nm.

2. Stow the nonworking wheel in the cargo

area.

The nonworking wheel cannot be stored

under the cargo floor panel because of its

size.

3. Check tire inflation pressure at the next op‐

portunity and correct as needed.

4. Reset the Tire Pressure Monitor.

5. Check to make sure the lug bolts are tight

with a calibrated torque wrench.

6. Drive to the nearest dealer’s service center

or another qualified service center or repair

shop to have the damaged tire replaced.

192

Engine compartment

Mobility

Engine compartment

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

Important features in the engine compartment

1

2

3

4

Jump-starting, negative battery terminal

Vehicle identification number

5

6

7

8

Engine compartment fuse box

Oil filler neck

Washer fluid reservoir

Coolant reservoir for charge air cooling

Coolant reservoir for engine cooling

Jump-starting, positive battery terminal

risk of personal and property damage. The

manufacturer of your vehicle recommends

that, in the effort to avoid such risks, work in

the engine compartment be performed by a

dealer’s service center or another qualified

service center or repair shop.◀

Hood

Safety information

WARNING

Improperly executed work in the engine

compartment can damage vehicle compo‐

nents and impair vehicle functions. There is a

193

Mobility

Engine compartment

WARNING

Hood is unlocked.

The engine compartment accommo‐

dates moving components. Certain compo‐

nents in the engine compartment can also

move with the vehicle switched off, e.g., the ra‐

diator fan. There is a risk of injury. Do not reach

into the area of moving parts. Keep articles of

clothing and hair away from moving parts.◀

WARNING

There are protruding parts, for instance

locking hook, on the inside of the hood. There

is a risk of injury. If the hood is open, pay atten‐

tion to protruding parts and keep clear of these

areas.◀

2. After the lever is released, pull the lever

again, arrow 2.

Hood can be opened.

Indicator/warning lights

When the hood is unlocked, a Check Control

message is displayed.

WARNING

An incorrectly locked hood can open

while driving and restrict visibility. There is a

risk of an accident. Stop immediately and cor‐

rectly close the hood.◀

Closing the hood

WARNING

Body parts can be jammed when open‐

ing and closing the hood. There is a risk of in‐

jury. Make sure that the area of movement of

the hood is clear during opening and closing.◀

NOTE

Folded-away wipers can be jammed

when the hood is opened. There is a risk of

property damage. Make sure that the wipers

with the wiper blades mounted are folded

down onto the windshield before opening the

hood.◀

Energetically close the hood with both hands.

The hood must engage on both sides.

NOTE

When the hood is closed, it must engage

on both sides. Pressing again can damage the

hood. There is a risk of property damage. Open

the hood again and then close it energetically.

Avoid pressing again.◀

Opening the hood

1. Pull lever, arrow 1.

194

Engine oil

Mobility

Engine oil

Vehicle features and options

Electronic oil measurement

Status display

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Concept

The engine oil level is monitored electronically

while driving and shown on the Control Dis‐

play.

If the engine oil level reaches the minimum

level, a Check Control message is displayed.

Functional requirements

General information

The engine oil consumption is dependent on

the driving style and driving conditions.

A current measured value is available after ap‐

prox. 30 minutes of driving. During a shorter

trip, the status of the last, sufficiently long trip

is displayed.

The engine oil consumption can increase in

the following situations, for example:

With frequent short-distance trips, regularly

perform a detailed measurement.

▷

Sporty driving style.

Break-in of the engine.

Idling of the engine.

Displaying the engine oil level

Via iDrive:

With use of engine oil types that are classi‐

fied as not suitable.

1. "Vehicle info"

2. "Vehicle status"

Therefore, regularly check the engine oil level

after refueling.

3.

"Engine oil level"

The engine oil level is displayed.

When a dynamic driving style is used, such as

when cornering fast, the system is unable to

measure the engine oil level. With this driving

style, measure the engine oil level using a de‐

tailed measurement, refer to page 196.

Engine oil level display messages

Different messages appear on the display de‐

pending on the engine oil level. Pay attention

to these messages.

The vehicle is equipped with electronic oil

measurement.

If the engine oil level is too low within the next

125 miles/200 km, add engine oil.

The electronic oil measurement has two meas‐

uring principles:

A red indicator light indicates that the

engine oil pressure is too low.

▷

Status display.

Detailed measurement.

NOTE

An engine oil level that is too low causes

engine damage. There is a risk of property

damage. Immediately add engine oil.◀

195

Mobility

Engine oil

Take care not to add too much engine oil.

NOTE

Adding engine oil

General information

Too much engine oil can damage the en‐

gine or the catalytic converter. There is a risk

of property damage. Do not add too much en‐

gine oil. When too much engine oil is added,

have oil level corrected by a dealer’s service

center or another qualified service center or re‐

pair shop.◀

Only add engine oil when the message is dis‐

played in the instrument cluster. The quantity

to be added is indicated in the message dis‐

played in the instrument cluster.

Switch off the ignition and safely park the vehi‐

cle before engine oil is added.

Take care not to add too much engine oil.

Detailed measurement

Concept

Spilled engine oil can damage carbon parts.

Wipe up spilled engine oil using a lint-free

cloth.

In the detailed measurement the engine oil

level is checked when the vehicle is stationary,

and displayed via a scale.

Safety information

WARNING

If the engine oil level reaches the minimum

level, a Check Control message is displayed.

Operating materials, e.g., oils, greases,

coolants, fuels, can contain harmful ingredi‐

ents. There is a risk of injuries or danger to life.

Observe the instructions on the containers.

Avoid the contact of articles of clothing, skin or

eyes with operating materials. Do not refill op‐

erating materials into different bottles. Store

operating materials out of reach of children.◀

During the measurement, the idle speed is in‐

creased somewhat.

Functional requirements

▷

Vehicle is parked in a horizontal position.

Manual transmission: shift lever in neutral

position, clutch and accelerator pedals not

depressed.

NOTE

An engine oil level that is too low causes

engine damage. There is a risk of property

damage.

▷

M Double clutch transmission: selector

lever in selector lever position N and accel‐

erator pedal not depressed.

Add engine oil within the next

125 miles/200 km.◀

Engine is running and is at operating tem‐

perature.

NOTE

Performing a detailed measurement

Too much engine oil can damage the en‐

gine or the catalytic converter. There is a risk

of property damage. Do not add too much en‐

gine oil. When too much engine oil is added,

have oil level corrected by a dealer’s service

center or another qualified service center or re‐

pair shop.◀

Using iDrive:

1. "Vehicle info"

2. "Vehicle status"

3.

"Measure engine oil level"

4. "Start measurement"

The engine oil level is checked and displayed

via a scale.

Overview

The oil filler neck is located in the engine com‐

partment, refer to page 193.

Time: approx. 1 minute.

196

Engine oil

Mobility

at a dealer’s service center or another qualified

service center or repair shop.

Opening the oil filler neck

1. Open the hood, refer to page 193.

2. Open the lid counterclockwise.

Alternative engine oil types

If an engine oil suitable for continuous use is

not available, up to 1 US quart/liter of an en‐

gine oil with the following oil rating can be

added:

Oil rating

BMW Longlife-01.

API SL or superior oil rating.

3. Add engine oil.

Viscosity grades

When selecting an engine oil, make sure that

the engine oil has the viscosity grade SAE

0W-30. Alternatively, also engine oils with vis‐

cosity grades SAE 5W-30, SAE 0W-40 or SAE

5W-40 can be used.

Engine oil types to add

General information

The engine oil quality is critical for the life of

the engine.

More information about suitable engine oil rat‐

ings and viscosities of engine oils can be re‐

quested from a dealer’s service center or an‐

other qualified service center or repair shop.

Safety information

NOTE

Oil additives can damage the engine.

There is a risk of property damage. Do not use

oil additives.◀

Engine oil change

NOTE

Engine oil that is not changed in timely

fashion can cause increased engine wear and

thus engine damage. There is a risk of property

damage. Do not exceed the service data indi‐

cated in the vehicle.◀

Incorrect engine oil can cause malfunc‐

tions in the engine or damage it. There is a risk

of property damage. When selecting an engine

oil, make sure that the engine oil has the cor‐

rect oil rating.◀

The vehicle manufacturer recommends that

you have a dealer’s service center or another

qualified service center or repair shop change

the engine oil.

Suitable engine oil types

You can add engine oils that meet the follow‐

ing oil rating standards:

Oil rating

BMW Longlife-01 FE.

More information about suitable engine oil rat‐

ings and viscosities of engine oils is available

197

Mobility

Engine oil

198

Coolant

Mobility

Coolant

Vehicle features and options

Coolant level

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Checking

1. Let the engine cool.

2. Turn the lid of the coolant reservoir slightly

counterclockwise to allow any excess

pressure to dissipate, then open it.

General information

The vehicle has two coolant reservoirs that are

located in the engine compartment.

To ensure the operational reliability of the vehi‐

cle, always check the coolant level of both

coolant reservoirs.

3. Open the coolant reservoir lid.

4. The coolant level is correct if it lies be‐

tween the minimum and maximum marks

in the filler neck.

Not all commercially available additives are

suitable for the vehicle. Information about suit‐

able additives is available from a dealer’s serv‐

ice center or another qualified service center or

repair shop.

Safety information

WARNING

With the engine hot and the cooling sys‐

tem open, coolant can escape and lead to

scalding. There is a risk of injury. Only open

the cooling system with the engine cooled

down.◀

WARNING

Additives are harmful and incorrect addi‐

tives can damage the engine. There is a risk of

injury and risk of property damage. Do not al‐

low additives to come into contact with skin,

eyes or articles of clothing. Use suitable addi‐

tives only.◀

199

Mobility

Coolant

Adding

1. Let the engine cool.

2. Turn the lid of the coolant reservoir slightly

counterclockwise to allow any excess

pressure to dissipate, then open it.

3. If the coolant is low, slowly add coolant up

to the specified level; do not overfill.

4. Close the cap.

5. Have the cause of the coolant loss elimi‐

nated as soon as possible.

Disposal

Comply with the relevant environmen‐

tal protection regulations when dispos‐

ing of coolant and coolant additives.

200

Maintenance

Mobility

Maintenance

General information

Vehicle features and options

Information on service requirements, refer to

page 88, can be displayed on the Control Dis‐

play.

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Service data in the remote control

Information on the required maintenance is

continuously stored in the remote control. The

dealer’s service center can read this data out

and suggest a maintenance scope for the vehi‐

cle.

Therefore, hand the service advisor the remote

control with which the vehicle was driven most

recently.

BMW maintenance system

The maintenance system indicates required

maintenance measures, and thereby provides

support in maintaining road safety and the op‐

erational reliability of the vehicle.

Storage periods

Storage periods during which the vehicle bat‐

tery was disconnected are not taken into ac‐

count.

In some cases, scopes and intervals may vary

according to the country-specific version. Re‐

placement work, spare parts, fuels and lubri‐

cants, and wear materials are calculated sepa‐

rately. Further information is available from a

dealer’s service center or another qualified

service center or repair shop.

If this occurs, have a dealer's service center or

another qualified service center or repair shop

update the time-dependent maintenance pro‐

cedures, such as checking brake fluid and, if

necessary, changing the engine oil and the mi‐

crofilter/activated-charcoal filter.

Condition Based Service

CBS

Service and Warranty

Information Booklet for US

models and Warranty and

Service Guide Booklet for

Canadian models

Please consult your Service and Warranty In‐

formation Booklet for US models and Warranty

and Service Guide Booklet for Canadian mod‐

els for additional information on service re‐

quirements.

Concept

Sensors and special algorithms take into ac‐

count the driving conditions of the vehicle.

CBS uses these to calculate the need for

maintenance.

The system makes it possible to adapt the

amount of maintenance corresponding to your

user profile.

The manufacturer of your vehicle recommends

that maintenance and repair be performed by a

dealer’s service center or another qualified

201

Mobility

Maintenance

service center or repair shop. Records of regu‐

lar maintenance and repair work should be re‐

tained.

Emissions

▷

The warning lamp lights up:

Emissions are deteriorating. Have

the vehicle checked as soon as

possible.

Socket for OBD Onboard

Diagnosis

▷

The warning lamp flashes under certain

circumstances:

This indicates that there is excessive mis‐

firing in the engine.

Safety information

NOTE

Reduce the vehicle speed and have the

system checked immediately; otherwise,

serious engine misfiring within a brief pe‐

riod can seriously damage emission con‐

trol components, in particular the catalytic

converter.

The socket for Onboard Diagnosis is an

intricate component intended to be used in

conjunction with specialized equipment to

check the vehicle’s primary emissions system.

Improper use of the socket for Onboard Diag‐

nosis, or contact with the socket for Onboard

Diagnosis for other than its intended purpose,

can cause vehicle malfunctions and creates

risks of personal and property damage. Given

the foregoing, the manufacture of your vehicle

strongly recommends that access to the

socket for Onboard Diagnosis be limited to a

dealer's service center or another qualified

service center or repair shop or other persons

that have the specialized training and equip‐

ment for purposes of properly utilizing the

socket for Onboard Diagnosis.◀

Position

There is an OBD socket on the driver's side for

checking the primary components in the vehi‐

cle's emissions.

202

Replacing components

Mobility

Replacing components

Replacing the wiper blades

1. To change the wiper blades, fold up the

wiper arms, refer to page 72.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

2. Fold up and hold the wiper arm firmly.

3. Squeeze the retainer spring, arrow 1, and

fold up the wiper blade, arrow 2.

Onboard vehicle tool kit

4. Remove the wiper blade forward from the

catch.

5. Insert the new wiper blade in reverse order

of removal until it locks in place.

6. Fold down the wipers.

NOTE

The onboard vehicle tool kit is located on the

right side in the cargo area in a storage com‐

partment. Open the cover.

Folded-away wipers can be jammed

when the hood is opened. There is a risk of

property damage. Make sure that the wipers

with the wiper blades mounted are folded

down onto the windshield before opening the

hood.◀

Wiper blade replacement

Safety information

Light/bulb replacement

General information

NOTE

If the wiper arm falls onto the windshield

without the wiper blades installed, the wind‐

shield can be damaged. There is a risk of prop‐

erty damage. Secure the wiper arm when re‐

placing the wiper blades and do not fold down

the wipers without the wiper blades installed.◀

Lights and bulbs

Lights and bulbs make an essential contribu‐

tion to vehicle safety.

The vehicle manufacturer recommends that

you have the relevant work carried out a deal‐

203

Mobility

Replacing components

er’s service center or another qualified service

center or repair shop.

Xenon headlights

DANGER

A spare light box is available from a dealer’s

service center or another qualified service cen‐

ter or repair shop.

There can be high voltage in the lighting

system. There is danger to life. The manufac‐

turer of your vehicle recommends that the

work on the lighting system including bulb re‐

placement be performed by a dealer’s service

center or another qualified service center or re‐

pair shop.◀

Observe the safety information, refer to

page 204.

Light-emitting diodes (LEDs)

Some items of equipment use light-emitting

diodes installed behind a cover as a light

source. These light-emitting diodes, which are

related to conventional lasers, are officially

designated as Class 1 light-emitting diodes.

Light-emitting diodes (LEDs)

WARNING

Too intensive brightness can irritate or

damage the retina of the eye. There is a risk of

injury. Do not look directly into the headlights

or other light sources. Do not remove the LED

covers.◀

Observe the safety information, refer to

page 204.

Safety information

Headlight glass

Lights and bulbs

Condensation can form on the inside of the ex‐

ternal lights in cool or humid weather. When

driving with the lights switched on, the con‐

densation evaporates after a short time. The

headlight glass does not need to be changed.

WARNING

Bulbs can get hot during operation. Con‐

tact with the bulbs can cause burns. There is a

risk of injury. Only change bulbs after they

have cooled off.◀

If despite driving with the lights switched on,

increasing humidity forms, e.g., water droplets

in the lamp, the manufacturer of your vehicle

recommends having it checked by a dealer’s

service center or another qualified service cen‐

ter or repair shop.

WARNING

Work on switched-on lighting systems

can cause short circuits. There is a risk of in‐

jury or risk of property damage. When working

on the lighting system, switch off the lamps in

question. If necessary, heed the bulb manufac‐

turer's instructions.◀

Headlight setting

The headlight adjustments can be affected by

changing lights and bulbs. After the headlight

adjustment was changed, have it checked and,

if necessary, corrected by a dealer’s service

center or another qualified service center or re‐

pair shop.

NOTE

Dirty bulbs have a reduced service life.

There is a risk of property damage. Do not hold

new bulbs with your bare hands. Use a clean

cloth or something similar, or hold the bulb by

its base.◀

204

Replacing components

Turn signal

Mobility

Front lights, bulb replacement

Xenon headlights

Observe the safety information, refer to

page 204.

24-watt bulb, PY24W

Information

1. In the wheel house, unscrew three screws

using the screwdriver from the onboard ve‐

hicle tool kit, arrow 1.

DANGER

There can be high voltage in the lighting

system. There is danger to life. The manufac‐

turer of your vehicle recommends that the

work on the lighting system including bulb re‐

placement be performed by a dealer’s service

center or another qualified service center or re‐

pair shop.◀

Because of the long life of these bulbs, the

likelihood of failure is very low. Switching the

lights on and off frequently shortens their life.

For checking and adjusting headlamp aim,

contact a dealer’s service center or another

qualified service center or repair shop.

2. Lift the wheel house panel and firmly hold

it, arrow 2.

3. Turn the bulb socket counterclockwise and

remove.

Headlamps

4. Press the bulb gently into the socket, turn

counterclockwise and remove.

1

2

3

Parking lights / daytime running lights

Low beams/high beams/headlight flasher

Turn signal

5. Install the new bulb and bulb holder in re‐

verse order of removal.

6. Refasten the wheel house panel.

Low beams and high beams are designed with

xenon technology.

LED headlights

The parking lights and daylight running lights

are made using LED technology.

Light-emitting diodes (LEDs)

In the case of a malfunction, contact a dealer’s

service center or another qualified service cen‐

ter or repair shop.

All front lamps and side turn signals are de‐

signed with LED technology.

205

Mobility

Replacing components

In the case of a malfunction, contact a dealer’s

service center or another qualified service cen‐

ter or repair shop.

tact a dealer’s service center or another quali‐

fied service center or repair shop.

Accessing the lights

Turn signal in exterior mirror

1. If needed, remove warning triangle, refer to

page 211, and bracket with the screw‐

driver from the onboard vehicle tool kit, re‐

fer to page 203.

The turn signals in the exterior mirrors feature

LED technology. In the case of a malfunction,

contact a dealer’s service center or another

qualified service center or repair shop.

2. Use the screwdriver from the onboard ve‐

hicle tool kit to loosen and completely re‐

move the screws on the trim.

Tail lamps, bulb replacement

Overview

3. Carefully loosen the trim from the tailgate,

starting at the edge and working toward

the area around the recessed grips. Make

sure that the trim does not become stuck.

1

2

3

4

5

Turn signal

Inside brake lamp

Reversing lamp

Tail lamps

4. Carefully swing out the trim.

Changing reversing lights

Outside brake lamp

1. Pull the bulb holder out.

Bulb replacement, exterior tail lamps

The outer tail lamps are made using LED tech‐

nology. In the case of a malfunction, contact a

dealer’s service center or another qualified

service center or repair shop.

Lights in the tailgate

General information

2. Unscrew the bulb from the bulb holder

counter-clockwise.

Observe the safety information, refer to

page 204.

3. Insert the new bulb.

Reversing lights: 21-watt bulb, H21W.

All lights in the tailgate are made using LED

technology. In the case of a malfunction, con‐

206

Replacing components

Mobility

License plate lamps and center brake

lamps

These lights are made using LED technology.

In the case of a malfunction, contact a dealer’s

service center or another qualified service cen‐

ter or repair shop.

Charging the battery

General information

Make sure that the battery is always suffi‐

ciently charged to guarantee that the battery

remains usable for its full service life.

A discharged battery is indicated by a

red indicator light.

Vehicle battery

The battery may need to be charged in the fol‐

lowing cases:

Maintenance

The battery is maintenance-free.

▷

When making frequent short-distance

drives.

More information about the battery can be re‐

quested from a dealer’s service center or an‐

other qualified service center or repair shop.

▷

If the vehicle is not used for more than a

month.

Replacing the vehicle battery

General information

Safety information

NOTE

Non-compatible external chargers can

After a battery replacement, the manufacturer

of your vehicle recommends that the vehicle

battery be registered on the vehicle by a deal‐

er’s service center or another qualified service

center or repair shop to ensure that all comfort

features are fully available and that any Check

Control messages of these comfort features

are no longer displayed.

damage the vehicle. There is a risk of personal

and property damage. Only charging devices

that are compatible with your vehicle and that

are below the maximum charge voltage should

be used to charge your vehicle. Information on

compatible chargers is available at your deal‐

er’s service center.◀

Maximum charge voltage: 14.4 volts.

NOTE

Safety information

NOTE

Battery chargers for the vehicle battery

can work with high voltages and currents,

which means that the 12 volt on-board net‐

work can be overloaded or damaged. There is

a risk of property damage. Only connect bat‐

tery chargers for the vehicle battery to the

starting aid terminals in the engine compart‐

ment.◀

Vehicle batteries that are not compatible

can damage vehicle systems and impair vehi‐

cle functions. There is a risk of personal and

property damage. Only vehicle batteries that

are compatible with your vehicle type should

be installed in your vehicle. Information on

compatible vehicle batteries is available at your

dealer’s service center.◀

Starting aid terminals

In the vehicle, only charge the battery via the

starting aid terminals, refer to page 212, in the

engine compartment with the engine off.

207

Mobility

Replacing components

Power failure

In the engine compartment

After a power loss, some equipment needs to

be newly initialized or individual settings up‐

dated, for example:

1. Use the onboard vehicle tool kit to loosen

the three cover screws, arrow 1.

▷

Seat and mirror memory: store the posi‐

tions again.

▷

Time: update.

Date: update.

Glass sunroof and sliding visor: initialize

the system.

Disposing of old batteries

2. Pull up the holder, arrow 2.

Have old batteries disposed of by a

dealer’s service center or another

qualified service center or repair shop

or take them to a collection point.

3. Remove the cover from one side, arrow 3.

4. Press the four fasteners and remove the

cover.

Fuses

Safety information

WARNING

Incorrect and repaired fuses can overload

electrical lines and components. There is a risk

of fire. Never attempt to repair a blown fuse.

Do not replace a nonworking fuse with a sub‐

stitute of another color or amperage rating.◀

Attaching the covers

1. When attaching the cover, make sure that

all four fasteners are engaged.

Replacing a fuse

The fuses are located in two different places in

the vehicle.

2. Attach the cover under the rubber lip and

then thread it between the bars.

Plastic tweezers and information on the fuse

types and locations are stored in the fuse box

in the cargo area.

3. Press down on the holder and tighten the

three screws.

208

Replacing components

Mobility

In the cargo area

Fold up the cargo floor panel.

Information on the fuse types and locations is

found on a separate sheet.

209

Mobility

Breakdown assistance

Overview

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

SOS button in the roofliner

Hazard warning flashers

Functional requirements

▷

The SIM card integrated in the vehicle has

been activated.

▷

The radio-ready state is switched on.

The Assist system is functional.

Initiating an Emergency Request

automatically

Under certain conditions, such as if the airbags

trigger, an Emergency Request is automati‐

cally initiated immediately after a severe acci‐

dent. Automatic Collision Notification is not af‐

fected by pressing the SOS button.

The button is located in the center console.

The red light in the button flashes when the

hazard warning flashers are activated.

Initiating an Emergency Request

manually

1. Press the cover briefly to open it.

Intelligent emergency call

Concept

2. Press the SOS button until the LED at the

button lights up green.

In case of an emergency, an Emergency Re‐

quest can be made through the system.

▷

The LED flashes green when a connection

to the BMW Response Center has been

established.

General information

Only press the SOS button in an emergency.

If the LED is flashing green, but the BMW

Response Center cannot be heard on the

hands-free system, the hands-free system

may possibly be malfunctioning. However,

the BMW Response Center may still be

able to hear you.

For technical reasons, the Emergency Request

cannot be guaranteed under unfavorable con‐

ditions.

210

Breakdown assistance

Mobility

When the Emergency Request is received

at the BMW Response Center, the BMW

Response Center contacts you and takes

further steps to help you.

First-aid kit

General information

Some of the articles have a limited service life.

Even if you are unable to respond, the

BMW Response Center can take further

steps to help you under certain circum‐

stances.

Check the expiration dates of the contents

regularly and replace any expired items

promptly.

For this, data is transmitted to the BMW

Response Center which serves to deter‐

mine the necessary rescue measures. E.g.,

the current position of the vehicle, if it can

be established.

Storage

Roadside Assistance

Service availability

Roadside Assistance can be reached around

the clock in many countries. You can obtain as‐

sistance there in the event of a vehicle break‐

down.

The first-aid kit is located in the cargo area in a

storage compartment.

Roadside Assistance

Jump-starting

The Roadside Assistance phone number can

be viewed via iDrive or a connection to Road‐

side Assistance can be established directly.

General information

If the battery is discharged, the engine can be

started using the battery of another vehicle

and two jumper cables. Only use jumper ca‐

bles with fully insulated clamp handles.

Warning triangle

Safety information

DANGER

Contact with live components can lead to

an electric shock. There is a risk of injuries or

danger to life. Do not touch any components

that are under voltage.◀

To prevent personal injury or damage to both

vehicles, adhere strictly to the following proce‐

dure.

The warning triangle is located on the inside of

the tailgate.

To remove, loosen the bracket.

211

Mobility

Breakdown assistance

Preparation

NOTE

In the case of body contact between the

two vehicles, a short circuit can occur during

jump-starting. There is a risk of property dam‐

age. Make sure that no body contact occurs.◀

1. Check whether the battery of the other ve‐

hicle has a voltage of 12 volts. The voltage

information can be found on the battery.

The body ground or a special nut acts as the

battery negative terminal.

2. Switch off the engine of the assisting vehi‐

cle.

Connecting the cables

1. Open the cover of the BMW starting aid

terminal.

3. Switch off any electronic systems/power

consumers in both vehicles.

Starting aid terminals

2. Attach one terminal clamp of the positive

jumper cable to the positive terminal of the

battery, or to the corresponding starting

aid terminal of the vehicle providing assis‐

tance.

WARNING

If the jumper cables are connected in the

incorrect order, sparking may occur. There is a

risk of injury. Pay attention to the correct order

during connection.◀

3. Attach the terminal clamp on the other end

of the cable to the positive terminal of the

battery, or to the corresponding starting

aid terminal of the vehicle to be started.

4. Attach one terminal clamp of the negative

jumper cable to the negative terminal of

the battery, or to the corresponding engine

or body ground of assisting vehicle.

5. Attach the second terminal clamp to the

negative terminal of the battery, or to the

corresponding engine or body ground of

the vehicle to be started.

The starting aid terminal in the engine com‐

partment acts as the battery's positive termi‐

nal.

Starting the engine

Never use spray fluids to start the engine.

Open the cover of the starting aid terminal.

1. Start the engine of the assisting vehicle

and let it run for several minutes at an in‐

creased idle speed.

2. Start the engine of the vehicle that is to be

started in the usual way.

If the first starting attempt is not success‐

ful, wait a few minutes before making an‐

212

Breakdown assistance

Mobility

other attempt in order to allow the dis‐

charged battery to recharge.

▷

Do not exceed a towing distance of

30 miles/50 km.

3. Let both engines run for several minutes.

Tow truck

4. Disconnect the jumper cables in the re‐

verse order.

With rear-wheel drive

Check the battery and recharge, if needed.

Tow-starting and towing

Safety information

WARNING

Due to system limits, individual functions

can malfunction during tow-starting/towing

with the Intelligent Safety systems activated,

e.g., approach control warning with light brak‐

ing function. There is a risk of an accident.

Switch all Intelligent Safety systems off prior to

tow-starting/towing.◀

Your vehicle should be transported with a tow

truck with a so-called lift bar or on a flat bed.

NOTE

When lifting the vehicle by the tow fitting

or body and chassis parts; damage can occur

on vehicle parts. There is a risk of property

damage. Lift vehicle using suitable means.◀

Manual transmission

Gearshift lever in neutral position.

Towing

M double-clutch transmission:

transporting the vehicle

Information the following instructions:

▷

Make sure that the ignition is switched on;

otherwise, the low beams, tail lamps, turn

signals, and wipers may be unavailable.

General information

The vehicle is not permitted to be towed.

▷

Do not tow the vehicle with the rear axle

tilted, as the front wheels could turn.

Safety information

NOTE

When the engine is stopped, there is no

power assist. Consequently, more force

needs to be applied when braking and

steering.

The vehicle can be damaged when tow‐

ing the vehicle with a single lifted axle. There is

a risk of property damage. The vehicle should

only be transported on a loading platform.◀

▷

Larger steering wheel movements are re‐

quired.

The towing vehicle must not be lighter

than the vehicle being towed; otherwise,

it will not be possible to control the vehi‐

cle's response.

▷

Do not exceed a towing speed of

30 mph/50 km/h.

213

Mobility

Breakdown assistance

rectly attach the tow bar or tow rope to the tow

fitting.◀

Tow truck

Tow bar

The tow fittings used should be on the same

side on both vehicles.

Should it prove impossible to avoid mounting

the tow bar at an offset angle, please observe

the following:

▷

Maneuvering capability is limited going

around corners.

The vehicle should only be transported on a

loading platform.

▷

The tow bar will generate lateral forces if it

is secured with an offset.

NOTE

When lifting the vehicle by the tow fitting

or body and chassis parts; damage can occur

on vehicle parts. There is a risk of property

damage. Lift vehicle using suitable means.◀

Tow rope

When starting to tow the vehicle, make sure

that the tow rope is taut.

To avoid jerking and the associated stresses

on the vehicle components when towing, al‐

ways use nylon ropes or nylon straps.

Towing other vehicles

General information

Switch on the hazard warning system, depend‐

ing on local regulations.

Tow fitting

General information

If the electrical system has failed, clearly iden‐

tify the vehicle being towed by placing a sign

or a warning triangle in the rear window.

Safety information

WARNING

If the approved gross vehicle weight of

the towing vehicle is lighter than the vehicle to

be towed, the tow fitting can tear off or it will

not be possible to control the vehicle's re‐

sponse. There is a risk of an accident! Make

sure that the gross vehicle weight of the tow‐

ing vehicle is heavier than the vehicle to be

towed.◀

The screw-in tow fitting should always be car‐

ried in the vehicle.

The tow fitting can be screwed in at the front

or rear of the vehicle.

The tow fitting and the onboard vehicle tool kit,

refer to page 203, are together in the cargo

area.

NOTE

If the tow bar or tow rope is attached in‐

correctly, damage to other vehicle parts can

occur. There is a risk of property damage. Cor‐

Use of the tow fitting:

214

Breakdown assistance

Manual transmission

Mobility

▷

Use only the tow fitting provided with the

vehicle and screw it all the way in.

If possible, do not tow-start the vehicle but

start the engine by jump-starting, refer to

page 211. If the vehicle is equipped with a cat‐

alytic converter, only tow-start while the en‐

gine is cold.

Use the tow fitting for towing on paved

roads only.

Avoid lateral loading of the tow fitting, for

instance do not lift the vehicle by the tow

fitting.

1. Switch on the hazard warning system and

comply with local regulations.

Safety information

2. Switch on the ignition, refer to page 64.

3. Engage third gear.

NOTE

If the tow fitting is not used as intended,

4. Have the vehicle tow-started with the

clutch pedal pressed and slowly release

the pedal. After the engine starts, immedi‐

ately press on the clutch pedal again.

there can be damage to the vehicle or to the

tow fitting. There is a risk of property damage.

Observe the notes on using the tow fitting.◀

5. Stop at a suitable location, remove the tow

bar or rope, and switch off the hazard

warning system.

Screw thread for tow fitting

6. Have the vehicle checked by a dealer’s

service center or another qualified service

center or repair shop.

Press on the mark of the front cover to push it

out.

Press out the rear cover at the recess using

the screw driver from the onboard vehicle tool

kit.

Tow-starting

M double-clutch transmission

Do not tow-start the vehicle.

Tow-starting the engine is not possible due to

the M double-clutch transmission.

Have the reasons for the starting difficulties

corrected by a dealer’s service center or an‐

other qualified service center or repair shop.

215

Mobility

Care

▷

Minimum distance from glass sunroof:

31.5 in/80 cm.

Vehicle features and options

This chapter describes all standard, country-

specific and optional features offered with the

series. It also describes features that are not

necessarily available in your vehicle, e. g., due

to the selected options or country versions.

This also applies to safety-related functions

and systems. When using these functions and

systems, the applicable laws and regulations

must be observed.

Automatic vehicle washes

Safety information

NOTE

Improper use of automatic vehicle

washes can cause damage to the vehicle.

There is a risk of damage to property. Follow

the following instructions:

▷

Give preference to cloth vehicle washes or

those that use soft brushes in order to

avoid paint damage.

Vehicle washes

General information

▷

Avoid vehicle washes with guide rails

higher than 4 in/10 cm to avoid damage to

the chassis.

Regularly remove foreign objects such as

leaves in the area below the windshield when

the hood is raised.

▷

Observe the tire width of the guide rail to

avoid damage to tires and rims.

Wash your vehicle frequently, particularly in

winter. Intense soiling and road salt can dam‐

age the vehicle.

Fold in exterior mirrors to avoid damage to

the exterior mirrors.

Deactivate the wiper and, if necessary, rain

sensor to avoid damage to the wiper sys‐

tem.◀

Steam blaster and high-pressure

washer

Safety information

Before driving into a vehicle wash

In order to ensure that the vehicle can roll in a

vehicle wash, take the following steps:

NOTE

When cleaning with high-pressure wash‐

ers, components can be damaged due to the

pressure or temperatures being too high.

There is a risk of property damage. Maintain

sufficient distance and do not spray too long

continuously. Follow the operating instructions

for the high-pressure washer.◀

Manual transmission:

1. Drive into the vehicle wash.

2. Shift to neutral.

3. Switch the engine off.

M double-clutch transmission:

Distances and temperature

1. Drive into the vehicle wash.

2. Engage selector lever position N.

3. Switch the engine off.

▷

Maximum temperature: 140 ℉/60 ℃.

Minimum distance from sensors, cameras,

seals: 12 inches/30 cm.

216

Care

Mobility

In this way, the ignition remains switched

on, and a Check-Control message is dis‐

played.

Thaw ice with de-icing spray; do not use an ice

scraper.

After washing the vehicle

NOTE

After washing the vehicle, apply the brakes

briefly to dry them; otherwise, braking action

can be reduced. The heat generated during

braking dries brake discs and brake pads and

protects them against corrosion.

Selector lever position P is automati‐

cally engaged when the ignition is

switched off. There is a risk of property

damage. Do not switch drive-ready state

off in vehicle washes.◀

Completely remove all residues on the win‐

dows, to minimize loss of visibility due to

smearing and to reduce wiper noises and

wiper blade wear.

Some vehicle washes do not permit persons in

the vehicle. The vehicle cannot be locked from

the outside when in selector lever position N. A

signal sounds when an attempt is made to lock

the vehicle.

Vehicle care

Driving out of a vehicle wash

To start the engine with manual transmission:

Vehicle care products

1. Ensure that the vehicle key is in the car.

2. Press on the clutch pedal.

General information

BMW recommends using vehicle care and

cleaning products from BMW. Suitable care

products are available from a dealer’s service

center or another qualified service center or re‐

pair shop.

3. Press the Start/Stop button.

To start the engine with a M double clutch

transmission:

1. Ensure that the vehicle key is in the car.

2. Depress the brake pedal.

Safety information

3. Press the Start/Stop button.

WARNING

Pressing the Start/Stop button without step‐

ping on the brake turns the ignition off.

Cleansers can contain substances that

are dangerous and harmful to your health.

There is a risk of injury. When cleaning the in‐

terior, open the doors or windows. Only use

products intended for cleaning vehicles. Fol‐

low the instructions on the container.◀

Transmission position

Transmission position P is engaged automati‐

cally:

▷

When the ignition is switched off.

After approx. 15 minutes.

Vehicle paint

General information

Headlights

Regular care contributes to driving safety and

value retention. Environmental influences in

areas with elevated air pollution or natural con‐

taminants, such as tree resin or pollen can af‐

fect the vehicle's paintwork. Tailor the fre‐

Do not rub the headlights dry and do not use

abrasive or acidic cleaning agents.

Soak areas that have been dirtied, for instance

from insects, with shampoo and wash off with

water.

217

Mobility

Care

quency and extent of your vehicle care to

these influences.

Safety information

NOTE

Aggressive substances such as spilled fuel, oil,

grease or bird droppings, must be removed im‐

mediately to prevent the finish from being al‐

tered or discolored.

Open Velcro® fasteners on articles of

clothing can damage the seat covers. There is

a risk of property damage. Ensure that any Vel‐

cro® fasteners are closed.◀

Matte finish

Only use cleaning and care products suitable

for vehicles with matte finish.

Caring for special components

Light-alloy wheels

When cleaning the vehicle, use only neutral

wheel cleaners having a pH value from 5 to 9.

Do not use abrasive cleaning agents or steam

jets above 140 ℉/60 ℃. Follow the manufac‐

turer's instructions.

Leather care

Remove dust from the leather regularly, using

a cloth or vacuum cleaner.

Otherwise, particles of dust and road grime

chafe in pores and folds, and lead to increased

wear and premature degradation of the leather

surface.

Aggressive, acidic or alkaline cleaning agents

can destroy the protective layer of adjacent

components, such as the brake disk.

To guard against discoloration, such as from

clothing, clean leather and provide leather care

roughly every two months.

After cleaning, apply the brakes briefly to dry

them. The heat generated during braking dries

brake discs and brake pads and protects them

against corrosion.

Clean light-colored leather more frequently be‐

cause soiling on such surfaces is substantially

more visible.

Chrome surfaces

Use leather care products; otherwise, dirt and

grease will gradually break down the protective

layer of the leather surface.

Carefully clean components such as the radia‐

tor grille or door handles with an ample supply

of water, possibly with shampoo added, partic‐

ularly when they have been exposed to road

salt.

Upholstery material care

General information

Rubber components

Vacuum the upholstery regularly with a vac‐

uum cleaner.

Environmental influences can cause surface

soiling of rubber parts and a loss of gloss. Use

only water and suitable cleaning agents for

cleaning.

If upholstery is very dirty, for instance with bev‐

erage stains, use a soft sponge or microfiber

cloth with a suitable interior cleaner.

Treat especially worn rubber parts with rubber

care agents at regular intervals. When cleaning

rubber seals, do not use any silicon-containing

vehicle care products in order to avoid damage

or noises.

Clean the upholstery down to the seams using

large sweeping motions. Avoid rubbing the

material vigorously.

218

Care

Mobility

Fine wood parts

Carpets and floor mats

Clean fine wood facing and fine wood compo‐

nents only with a moist rag. Then dry with a

soft cloth.

WARNING

Objects in the driver's floor area can limit

the pedal distance or block a depressed pedal.

There is a risk of an accident. Stow objects in

the vehicle such that they are secured and

cannot enter into the driver's floor area. Use

floor mats that are suitable for the vehicle and

can be safely attached to the floor. Do not use

loose floor mats and do not layer several floor

mats. Make sure that there is sufficient clear‐

ance for the pedals. Ensure that the floor mats

are securely fastened again after they were re‐

moved, e.g., for cleaning.◀

Plastic components

NOTE

Cleansers that contain alcohol or sol‐

vents, such as lacquer thinners, heavy-duty

grease removers, fuel, or such, can damage

plastic parts. There is a risk of property dam‐

age. Clean with a microfiber cloth. Dampen

cloth lightly with water.◀

Plastic components are e.g.:

Floor mats can be removed from the vehicle's

interior for cleaning.

▷

Imitation leather surfaces.

Roofliner.

If the floor carpets are very dirty, clean with a

microfiber cloth and water or a textile cleaner.

To prevent matting of the carpet, rub back and

forth in the direction of travel only.

Lamp lenses.

Instrument cluster cover.

Matt black spray-coated components.

Painted parts in the interior.

Sensor/camera lenses

Clean with a microfiber cloth.

Dampen cloth lightly with water.

Do not soak the roofliner.

To clean sensors and camera lenses, use a

cloth moistened with a small amount of glass

detergent.

Displays/Screens/protective glass of

the Head-up Display

Safety belts

WARNING

NOTE

Chemical cleansers can destroy the

safety belt webbing. Missing protective effect

of the safety belts. There is a risk of injuries or

danger to life. Use only a mild soapy solution

for cleaning the safety belts.◀

Chemical cleansers, moisture or fluids of

any kind can damage the surface of displays

and screens. There is a risk of property dam‐

age. Clean with a clean, antistatic microfiber

cloth.◀

Dirty belt straps impede the reeling action and

thus have a negative impact on safety.

NOTE

Use only a mild soapy solution, with the safety

belts clipped into their buckles.

The surface of displays can be damaged

with improper cleaning. There is a risk of prop‐

erty damage. Avoid pressure that is too high

and do not use any scratching materials.◀

Do not allow the switchs to retract the safety

belts until they are dry.

Clean with a clean, antistatic microfiber cloth.

219

Mobility

Care

Clean the protective glass of the Head-up Dis‐

play using a microfiber cloth and commercially

available dish-washing soap.

Long-term vehicle storage

When the vehicle is shut down for longer than

three months, special measures must be

taken. Further information is available from a

dealer’s service center or another qualified

service center or repair shop.

220

Care

Mobility

221

Mobility for Your BMW M3 4 Door Fifth Generation (2014-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals