Get STEERING WHEEL CONTROLS Guide for Citroen Berlingo SUV First Generation (1996-2008)

Steering wheel controls

Lights off

Automatic lights

Side lights

Dipped beam (green)

Main beam (blue)

DIRECTION INDICATORS

(green flashing)

LIGHTING CONTROL

Dipped beam/main beam change

Pull the stalk fully towards you.

Left: downwards passing the

point of resistance.

Right: upwards passing the

point of resistance.

Front and rear lights

Selection is by turning ring A.

Lights-on buzzer

Checking by means of the indicator

lights on the instrument panel is

described in the "Instruments and

controls" section of chapter 2.

When the ignition is switched off, when

the driver’s door is opened, a buzzer

sounds if you have left your lights on.

"Motorway" function

Press the control up or down to ﬂash

the corresponding direction indicator

three times.

Steering wheel controls

Lights off

Automatic lights

Side lights

Dipped beam (green)

Main beam (blue)

DIRECTION INDICATORS

(green flashing)

LIGHTING CONTROL

Dipped beam/main beam change

Pull the stalk fully towards you.

Left: downwards passing the

point of resistance.

Right: upwards passing the

point of resistance.

Front and rear lights

Selection is by turning ring A.

Lights-on buzzer

Checking by means of the indicator

lights on the instrument panel is

described in the "Instruments and

controls" section of chapter 2.

When the ignition is switched off, when

the driver’s door is opened, a buzzer

sounds if you have left your lights on.

"Motorway" function

Press the control up or down to ﬂash

the corresponding direction indicator

three times.

Steering wheel controls

Front and rear fog lamps

Daytime lights

Automatic switching on of the lights

Rotate ring B forwards to switch on and

rearwards to switch off. The status is

conﬁrmed by the light on the instrument

panel.

These operate with the side lights and

the dipped beam headlamps.

The side lights

and dipped beam

headlamps switch

Depending on the country in which the

vehicle is sold, the vehicle may be equipped

with daytime lights. The dipped headlamps

come on when the vehicle is started.

on automatically if

the light is poor, or

during operation of the windscreen

wipers. They switch off as soon as the

light becomes bright enough or the

windscreen wipers stop.

This warning light comes on

on the instrument panel.

This function is not compatible with the

daytime lights.

Front fog lamps (green,

1st rotation of the ring

forwards).

The instruments and controls

(instrument panel, display, air

conditioning control panel, ...)

In foggy weather or in snow,

the brightness sensor can detect

sufﬁcient light. As a consequence,

Rear fog lamps (amber,

2nd rotation of the ring

forwards).

are only lit on switching to the automatic the lights will not come on automatically.

switching on of the lights mode or when If necessary, you must switch on the

the lights are switched on manually.

dipped headlamps manually.

Do not cover the brightness

sensor located on the windscreen,

behind the mirror. It is used for

the automatic switching on of the lights

and for the automatic wipers.

To switch off the front and rear fog

lamps, turn the ring rearwards twice

in succession.

In clear weather or in rain, both day

and night, rear fog lamps dazzle and

are prohibited.

Activation

Turn the ring to the AUTO position.

The activation of this function is

accompanied by a message on the

display.

Do not forget to switch them off

when they are no longer needed.

Automatic switching on of the lights

switches off the rear fog lamps, but the

front fog lamps remain on.

Deactivation

Turn the ring forwards or rearwards.

The deactivation of this function is

accompanied by a message on the

display.

The function is deactivated temporarily

when you use the manual lights stalk.

3

Steering wheel controls

If the brightness sensor

does not function

correctly, the lights come on

accompanied by the service

warning light, an audible signal

and a message on the display.

Consult a CITROËN dealer.

Follow-me-home lighting

The temporary maintaining of the

dipped headlamps lighting, with the

ignition off, makes the driver’s exit

easier when the light is poor.

Manual operation

HEADLAMP BEAM

-

With the ignition off, "ﬂash" the

headlamps within one minute after

switching off the ignition.

Depending on the load in your vehicle,

the beam setting must be adjusted.

0 - No load.

1 - Partial load.

2 - Average load.

3 - Maximum authorised load.

The follow-me-home lighting switches

off automatically after a set time.

Automatic operation

Activate the function via the

"Vehicle conﬁg" menu.

Initial setting is position 0.

Refer to the "Display ﬂow chart"

section of chapter 4.

Steering wheel controls

If the brightness sensor

does not function

correctly, the lights come on

accompanied by the service

warning light, an audible signal

and a message on the display.

Consult a CITROËN dealer.

Follow-me-home lighting

The temporary maintaining of the

dipped headlamps lighting, with the

ignition off, makes the driver’s exit

easier when the light is poor.

Manual operation

HEADLAMP BEAM

-

With the ignition off, "ﬂash" the

headlamps within one minute after

switching off the ignition.

Depending on the load in your vehicle,

the beam setting must be adjusted.

0 - No load.

1 - Partial load.

2 - Average load.

3 - Maximum authorised load.

The follow-me-home lighting switches

off automatically after a set time.

Automatic operation

Activate the function via the

"Vehicle conﬁg" menu.

Initial setting is position 0.

Refer to the "Display ﬂow chart"

section of chapter 4.

Steering wheel controls

In the AUTO position, the windscreen

wipers operate automatically and adapt

their speed to theintensityof the rainfall.

When not in AUTO mode, for the

other positions, refer to the manual

windscreen wipers section.

Activation

Press the control downwards. Activation

of the function is accompanied by

a message on the display.

The automatic windscreen wipers

function must be reactivated if the

ignition has been switched off for more

than one minute, by pressing the stalk

downwards.

Deactivation/Switching off

Place the windscreen wipers stalk in

position I, 1 or 2. Deactivation of the

function is accompanied by a message

on the display.

In the event of malfunction of the

automatic windscreen wipers, the

windscreen wipers will operate in

intermittent mode.

WINDSCREEN WIPER STALK

Manual windscreen wipers

Whenever the ignition has been

switched off for more than one

minute,with the windscreen wiper stalk

inposition 2, 1 or I, the stalk must be

reactivated:

2

1

l

Fast wipe (heavy rain).

Normal wipe (moderate rain).

Intermittent wipe.

Off.

-

move the stalk to any position,

then move it back to the required

position.

0

Contact a CITROËN dealer to have the

system checked.

 Single wipe

(press downwards).

In the Intermittent position, the wiping

speed is in proportion to the vehicle

speed.

When using an automatic car

wash, switch off the ignition to

avoid triggering of the automatic

wiping.

Automatic windscreen wipers

Do not cover the rain sensor,

located in the centre of the

windscreen, behind the mirror. windscreen to completely clear of ice

In winter, it is advisable to wait for the

before operating the automatic wipe.

3

Steering wheel controls

Wash-wipe and headlamp wash

Pull the stalk towards you, the wash-wipe

is accompanied by a timed sweep of the

wipers.

The headlamp wash is linked with the

wash-wipe, it is triggered if the dipped

headlamps are on.

To top up the levels, refer to the

"Levels" section of chapter 7.

Special position of the

windscreen wipers

In the minute following switching

off of the ignition, any action on the

stalk positions the wipers against the

windscreen uprights.

This action enables you to position

the wiper blades for winter parking,

cleaning or replacement.

Rear windscreen wiper

Rear windscreen wash

Turn the ring to the ﬁrst notch.

Turn the ring past the ﬁrst

notch: the windscreen wash

then the windscreen wiper

operate for a ﬁxed time.

Refer to the "Changing a

windscreen wiper blade" section of

chapter 8.

To park the wipers in their normal

position after this has been done, switch

on the ignition and move the stalk.

In winter, in the event of a

considerable amount of snow

or ice, switch on the rear screen

demister. Once de-icing is complete,

remove the snow or ice which has

accumulated on the rear wiper

blade. You can then operate the rear

windscreen wiper.

Steering wheel controls

This cruise control shows the function

selection status on the instrument

panel and displays the programmed

speed:

Function selected,

displaying of the

"Cruise Control"

symbol.

Function deactivated,

OFF (example at

107 km/h).

Function activated

(example at

107 km/h).

CRUISE CONTROL "CRUISE"

Vehicle speed above

(e.g. 118 km/h),

the programmed

speed is displayed

ﬂashing.

"This is the speed at which the driver

wishes to drive".

This aid to driving in free-ﬂowing

trafﬁc enables the vehicle to maintain

the speed programmed by the driver,

unless a steep gradient makes this

impossible.

In order for it to be programmed or

activated, the vehicle speed must be

greater than 25 mph (40 km/h) with at

least 4th gear engaged.

Operating fault

detected,

OFF - the dashes

ﬂash.

3

Steering wheel controls

Selecting the function

Temporary exceeding of the

speed

Reactivation

-

Place the switch in the CRUISE

position. The cruise control is

selected but is not yet active and

no speed has been programmed.

-

Following deactivation of the cruise

control, press this button.

It is possible to accelerate and drive

momentarily at a speed greater than

the programmed speed. The value

programmed ﬂashes.

When the accelerator pedal is

released, the vehicle will return to the

programmed speed.

Your vehicle will return to the last

programmed speed.

Alternatively, you can repeat the "ﬁrst

activation" procedure.

First activation/

programming a

speed

Deactivation (off)

- Reach the chosen

speed by pressing

the accelerator.

- Press this button or

the brake or clutch

pedal.

- Press the SET -

or SET + button.

This programmes/activates the

reference speed and the vehicle will

maintain this speed.

Steering wheel controls

Good practice

When changing the programmed

reference speed by means of

a maintained press, pay attention as

the speed can increase or decrease

rapidly.

Do not use the cruise control on

slippery roads or in heavy trafﬁc.

In the event of a steep slope, the cruise

control cannot prevent the vehicle from

exceeding the programmed speed.

In any event, the cruise control cannot

replace the need to observe the speed

limits, nor can it replace the need for

vigilance and responsibility on the part

of the driver.

It is advisable to leave your feet near

the pedals.

Changing the

programmed speed

Switching the function off

-

Place the dial in position 0 or

switch off the ignition to switch

everything off.

There are two methods

of memorising a

speed higher than the

previous one:

Cancelling the programmed

reference speed

Without using the accelerator:

press the Set + button.

When the vehicle becomes stationary,

after switching off the ignition, the

system no longer memorises a speed.

-

A brief press increases the speed

by 1 mph (km/h).

A maintained press increases

To avoid any jamming under the

pedals:

the speed in steps of 5 mph (km/h).

-

ensure that the mat and its ﬁxings

on the ﬂoor are positioned correctly,

Using the accelerator:

-

exceed the memorised speed until

the speed required is reached,

press the Set + or Set - button.

-

never place one mat on top of

another.

-

To memorise a speed lower than the

previous one:

press the Set - button.

A brief press decreases the speed

by 1 mph (km/h).

-

Operating fault

The programmed speed is cleared then

replaced by three dashes. Contact a

CITROËN dealer to have the system

checked.

A maintained press decreases the

speed in steps of 5 mph (km/h).

3

Steering wheel controls

This speed limiter shows the function

selection status on the instrument

panel and displays the programmed

speed:

Function selected,

displaying of the

"Speed Limiter"

symbol.

Function deactivated,

last programmed

speed - OFF

(example at 65 mph

(107 km/h)).

Function activated

(example at 65 mph

(107 km/h)).

SPEED LIMITER "LIMIT"

Vehicle speed above

(example 70 mph

(118 km/h)),

the programmed

speed is displayed

ﬂashing.

"This is the selected speed which the

driver does not wish to exceed".

This selection is made with the engine

running while stationary or with the

vehicle moving. The minimum speed

which can be programmed is 20 mph

(30 km/h).

The speed of the vehicle responds

to the pressure of the driver’s foot as

far as the accelerator pedal point of

resistance which indicates that the

programmed speed has been reached.

However, pressing the pedal beyond

this point of resistance to the ﬂoor

permits exceeding of the programmed

speed. To resume use of the limiter,

simply reduce the pressure on the

accelerator pedal gradually and return

to a speed below that programmed.

The operating actions may be

carried out when stationary, with the

engine running, or with the vehicle

moving.

Operating fault

detected,

OFF - the dashes

ﬂash.

Steering wheel controls

Selecting the function

-

Place the dial in the LIMIT position.

The limiter is selected but is not yet

active. The display indicates the

last programmed speed.

Programming a speed

Activation/Deactivation (off)

A speed can be programmed without Pressing this button once activates

activating the limiter but with the engine the limiter, pressing the button again

running.

deactivates it (OFF).

To memorise a speed higher

than the previous one:

-

press the Set + button.

A brief press increases the speed

by 1 mph (km/h).

A maintained press increases the

speed in steps of 5 mph (km/h).

To memorise a speed lower than the

previous one:

-

press the Set - button.

A brief press decreases the speed

by 1 mph (km/h).

A maintained press decreases the speed

in steps of 5 mph (km/h).

3

Steering wheel controls

Exceeding the programmed

speed

Switching the function off

Operating fault

-

Place the dial in position 0 or switch

off the ignition to switch the system

off.

The programmed speed is cleared

then replaced by three dashes.

Contact a CITROËN dealer to have the

system checked.

Pressing the accelerator pedal in order

to exceed the programmed speed

will have no effect unless you press

the pedal ﬁrmly beyond the point of

resistance.

The last programmed speed remains in

the memory.

The limiter is deactivated temporarily

and the programmed speed ﬂashes.

To return to the limiter function, reduce

your speed to below the programmed

speed.

Good practice

In any event, the speed limiter cannot

replace the need to observe speed

limits, nor can it replace the need for

vigilance and responsibility on the part

of the driver.

Always pay attention to the proﬁle of the

road and sharp acceleration and stay in

complete control of your vehicle.

Flashing of the speed

The speed ﬂashes:

-

To avoid any jamming under the pedals:

-

following forcing of the accelerator

point of resistance,

ensure that the mat and its ﬁxings

on the ﬂoor are positioned correctly,

-

when the limiter cannot prevent an

increase in the vehicle speed due

to the proﬁle of the road or on a

steep descent,

-

never place one mat on top of

another.

-

in the event of sharp acceleration.

Ventilation

Heating control panel

Air flow

Air conditioning control panel

VENTILATION

Manual adjustments:

Temperature

The force of the blown air

the footwells,

at the vents varies from 1 to

the strongest 4. Position 0

switches it off.

Control positioned:

in the blue zone, triggers

cool air,

Remember to adjust this control in order

to reach the ambient air comfort level.

the windscreen and

the footwells,

in the red zone, triggers

heating of the interior

ambient air.

Air distribution

The air supply distribution is determined

by the following symbols:

the windscreen.

the side vents and the central

vents,

The air distribution can be

modulated by placing the

control in the intermediate

positions, marked "ꢀ".

3

Ventilation

Intake of exterior air

Air conditioning A/C

The air conditioning can only operate

with the engine running.

The diode on the button

is off. This is the preferred

operating position.

Pressing the button triggers

the operation of the air

conditioning, the diode is lit.

Pressing the button again

switches the function off and

the diode is switched off.

Recirculation of interior air

The diode on the button is

lit. Recirculation temporarily

prevents exterior odours

and smoke from entering the

passenger compartment.

The air conditioning does not operate

if the air ﬂow is set to 0.

Used with the setting of the force of

blown air (from 1 to 4), recirculation

enables you to obtain the required

ambient air comfort level more quickly

with both hot or cold settings.

This position should only be temporary.

When your ambient air comfort level

has been reached, return to the

intake of exterior air position to permit

renewal of the air in the passenger

compartment and avoid misting.

This operating mode is preferable.

STEERING WHEEL CONTROLS for Your Citroen Berlingo SUV First Generation (1996-2008)

Related Topics

Popular Owner Manuals

Latest Owner Manuals