Get Access Guide for Citroen Berlingo SUV Third Generation (2018-2025)

Access

the "hands-free" functions are set to

hibernation mode after 21 days without use.

To restore these functions, press one of the

remote control buttons or start the engine with

the electronic key in the reader.

Unfolding / Folding the key

Electronic key with

remote control function

and built-in key,

For more information on starting with the

Keyless Entry and Start system, refer to the

corresponding section.

If one of the doors or the boot is still open

or if the electronic key for the Keyless

Entry and Start system has been left inside

the vehicle, central locking will not take place.

However, if the vehicle is ﬁtted with an alarm,

it will be activated after 45 seconds.

Electrical interference

The electronic key may not work if it is

close to an electronic device (e.g. mobile

telephone (switched on or on standby), laptop

computer, strong magnetic ﬁelds). If this

occurs, move the electronic key away from

the electronic device.

► Press this button to unfold or fold the key.

The remote control may be damaged if

you do not press the button.

If the vehicle is unlocked but the doors or

tailgate are not subsequently opened, the

vehicle will automatically lock itself again after

about 30 seconds. If the vehicle is ﬁtted with

an alarm, it will be reactivated automatically.

Keyless Entry and Start

This allows the central locking or unlocking of the

vehicle from a distance.

It is also used to locate and start the vehicle, as

well as providing protection against theft.

Remote control key

Automatic door mirror folding and

unfolding can be deactivated by a

CITROËN dealer or a qualiﬁed workshop.

This allows the central locking or unlocking of the

vehicle using the door lock or from a distance.

It also allows the vehicle to be located, the fuel

ﬁller cap and charging ﬂap to be opened and

closed and the engine to be started or switched

oﬀ, as well as providing protection against theft.

Integral key

This is used to lock and unlock the vehicle when

the remote control cannot operate:

– remote control battery discharged, vehicle

battery discharged or disconnected, etc.

– vehicle located in an area subject to strong

electromagnetic interference.

As a safety measure, never leave the

vehicle, even for a short time, without

taking the Keyless Entry and Start system’s

electronic key with you.

Be aware of the risk of theft of the vehicle if

the key is present in one of the deﬁned areas

while the vehicle is unlocked.

The remote control buttons are not active

with the ignition switched on.

To preserve the battery charge in the

electronic key and the vehicle's battery,

32

Access

It allows the unlocking, locking and starting of the

vehicle, while carrying the remote control on your

person in the recognition zone "A".

Advice

2

Remote control

The remote control is a sensitive, high-

frequency device; avoid handling it in your

pocket, due to the risk of unintentionally

unlocking the vehicle.

Avoid pressing the remote control buttons

while out of range of the vehicle, due to

the risk of rendering the remote control

inoperative. It would then be necessary to

reset it.

In the ignition on (accessories) position,

with the "START/STOP" button, the

hands-free function is deactivated and it is

impossible to open the doors.

For more information on Starting/switching

oﬀ the engine and in particular the "ignition

on" position, refer to the corresponding

section.

► Keep this button 1 pulled across to remove

the key 2 from the device.

If the alarm is activated, the audible

signal triggered on opening a door with

the key (integral with the remote control) will

stop when the ignition is switched on.

The remote control does not work when the

key is in the ignition switch, even when the

ignition is switched oﬀ.

Locating the vehicle

Once the built-in key is ejected, always

keep it with you to be able to carry out

the corresponding back-up procedures.

This function helps you to spot your vehicle from

a distance, with the vehicle locked:

– The direction indicators ﬂash for approximately

10 seconds.

Anti-theft protection

Do not modify the electronic vehicle

immobiliser, as this might result in

malfunctions.

For vehicles with a key ignition switch,

remember to remove the key and turn the

steering wheel to engage the steering lock.

"Keyless Entry and Start" on your

person

– The courtesy lamps come on.

► Press this button.

Remote operation of lighting

A short press on this button switches on

the lighting remotely (lighting of

Locking the vehicle

Driving with the doors locked could make

it more diﬃcult for the emergency services

to enter the passenger compartment in an

emergency.

sidelamps, dipped beam headlamps and number

plate lamps).

A second press on the button before the end of

the timed period cancels the remote lighting.

As a safety precaution, remove the key from

the ignition or take the electronic key with you

when leaving the vehicle, even for a short

time.

33

Access

Purchasing a second-hand vehicle

Have the key codes memorised by a

CITROËN dealer, to ensure that the keys in

your possession are the only ones able to

start the vehicle.

An audible signal and, depending on equipment,

a display message, conﬁrm that the request has

been acknowledged.

Without button

The selectivity between the

driver's door and the other doors

and the boot is activated or deactivated via the

vehicle conﬁguration menu.

Accumulations (water, dust, grime, salt,

etc.) on the inner surface of the door

handle may aﬀect detection.

If cleaning the inner surface of the door

handle using a cloth does not restore

detection, contact a CITROËN dealer or a

qualiﬁed workshop.

A sudden splash of water (stream of water,

high pressure jet washer, etc.) may be

identiﬁed by the system as the desire to open

the vehicle.

Selective unlocking unlocks either the cabin

doors, or the doors of the loading area (side

and rear).

Complete unlocking

The separation of the cabin and loading

area unlocking is a security measure.

It is used to lock out access to the part of the

vehicle in which you are not present.

With the key

► To completely unlock the vehicle, insert the

key in the lock then turn it towards the front of

the vehicle.

► Then pull the handle to open the door.

If ﬁtted to your vehicle, the alarm is not

deactivated. Opening a door will trigger the

alarm, which can be stopped by switching the

ignition on.

Activation/Deactivation

With button

Total or selective

unlocking

Using the remote control

► Press one of these buttons to

unlock the vehicle.

Unlocking is conﬁrmed by rapid ﬂashing

of the direction indicators for around 2

seconds.

At the same time, depending on your version,

the door mirrors unfold.

► To activateselective unlocking between

the cab and the loading area or to deactivate

selective unlocking and return to total unlocking

mode, switch on the ignition and press this

button for more than two seconds.

Complete unlocking unlocks all the vehicle’s

doors (front, side and rear).

34

Access

With Keyless Entry and Start on your

person

► To unlock the vehicle, remote control in

the recognition zone A, run a hand behind the

handle of the side-hinged door.

► Press this button on the remote

control to unlock only the loading area.

2

Unlocking is conﬁrmed by rapid ﬂashing

of the direction indicators for around 2

► Then pull the handle to open it.

With tailgate

seconds.

At the same time, depending on your version,

the door mirrors unfold.

With Keyless Entry and Start on your

person

► To unlock the vehicle, with the remote control

on your person in recognition zone A, pass

your hand behind one of the door handles (front

door(s), manual sliding side door(s) or side-

hinged doors).

► Pull the handle to open the corresponding

door.

With side-hinged doors

► To unlock the vehicle, with the remote control

in recognition zone A, press the tailgate release

control.

► To unlock the cabin alone, with the

remote control on your person in

► Raise the tailgate.

recognition zone A, pass your hand behind the

handle of the driver’s door.

Selective unlocking

► To unlock the cabin alone, with the

remote control on your person in

recognition zone B, pass your hand behind the

handle of the driver's door.

Using the remote control

► To unlock just the passenger

compartment doors, press this button

once.

► To unlock the side and rear doors in the

loading area, press this button a second time.

or

► Then pull the handle to open the cabin.

The door locking state of the loading

area remains unchanged.

35

Access

► To unlock the loading area alone, with the

remote control on your person in the recognition

zone A, B or C, pass your hand behind a handle

of the left side door, right side door or the rear

door (the left-hand hinged door or the tailgate).

► Then pull the handle to open the loading

area.

If ﬁtted to your vehicle, the alarm is not

deactivated. Opening a door will trigger the

alarm, which can be stopped by switching the

ignition on.

your hand behind one of the door handles (front

door(s)).

► Pull the handle to open the corresponding

door.

With side-hinged doors/tailgate

Using the remote control

► Press this button to unlock the vehicle.

Depending on version, the door mirrors

unfold only when the cabin is unlocked,

the alarm is deactivated.

With Keyless Entry and

Start on your person

Unlocking

Unlocking is signalled by rapid ﬂashing of

the direction indicators for a few

seconds.

Depending on version, the door mirrors unfold

and the alarm is deactivated.

► To unlock the vehicle, with the remote control

on your person in recognition zone A, pass

your hand behind one of the door handles (front

door(s), manual sliding side door(s) or side-

hinged doors).

With the key

► To completely unlock the vehicle, insert the

key in the lock then turn it towards the front of

the vehicle.

► To unlock the vehicle, with the remote control

in the recognition zone A, pass your hand

behind the side-hinged door handle or press the

tailgate unlocking control.

► To unlock the vehicle, with the remote control

on your person in recognition zone A, pass

► Then pull the handle to open the door.

36

Access

► Pull the side-hinged door handle or raise the

tailgate.

The locking/deadlocking is signalled by

the ﬁxed illumination of the direction

indicators for about two seconds.

Depending on your version, the door mirrors

fold at the same time.

► To lock the vehicle, with the remote control in

recognition zone A, press the markings on one

of the front or rear door handles.

2

With an opening rear screen in the

tailgate

► To lock the vehicle, with the remote control in

recognition zone A, press the markings on one

of the front door handles.

If your vehicle is so equipped, pressing

and holding the locking button closes the

windows. The window stops in position when

you release the button.

With side-hinged doors

With the key

► To lock the vehicle, insert the key in the lock

then turn it towards the rear of the vehicle.

With the remote control

► To lock the vehicle, press this button.

► With the Keyless Entry and Start on your

person, to unlock the vehicle, press the tailgate

opening rear screen unlocking control. The

screen will open slightly; then, lift it up to open it.

► To lock the vehicle, with the remote control

in recognition zone A, press the left-hand door

locking control.

With Keyless Entry and

Start on your person

Driving with the doors locked could make

it more diﬃcult for the emergency

Locking

services to enter the vehicle in an emergency.

As a safety measure, never leave the vehicle,

even for a short time, without taking the

remote control with you.

Ensure that no person or object prevents

the correct closing of the windows.

Be particularly aware of children when

operating the windows.

If a door is not properly closed (except the

right-hand door with side-hinged rear

doors):

37

Access

– when the vehicle is stationary and engine

running, this warning lamp comes on,

accompanied by a warning message for a few

seconds,

– when the vehicle is moving (at speeds above

6 mph (10 km/h)), this warning lamp comes on,

accompanied by an audible signal and a warning

message for a few seconds.

With Keyless Entry and Start on your

person

Back-up procedures

Lost keys, remote control,

electronic key

Go to a CITROËN dealer with the vehicle's

registration certiﬁcate, your personal

identiﬁcation documents and if possible, the label

bearing the key code.

The CITROËN dealer will be able to retrieve the

key code and the transponder code, enabling a

new key to be ordered.

► To lock the vehicle, with the remote control in

recognition zone A, press the markings on one

of the front or rear door handles.

► To deadlock the vehicle, press the markings

again within ﬁve seconds.

Deadlocking

Deadlocking renders the exterior and

interior door controls inoperative. It also

deactivate the manual central control button.

The horn remains operational.

Never leave anyone inside the vehicle

when it is deadlocked.

With side-hinged doors

Complete unlocking/locking

of the vehicle with the key

Use this procedure in the following situations:

– Remote control battery discharged.

– Remote control malfunction.

– Vehicle battery discharged.

– Vehicle in an area subject to strong

electromagnetic interference.

In the ﬁrst case, change the remote control

battery.

In the second case, reinitialise the remote

control.

Refer to the corresponding sections.

► Insert the key into the front left-hand door

lock.

With the key

► To deadlock the vehicle, turn the key in the

driver's door lock towards the rear of the vehicle.

► Then within ﬁve seconds, turn the key

towards the rear again.

► To lock the vehicle, with the remote control

in recognition zone A, press the left-hand door

locking control.

► To deadlock the vehicle, press the control

again within ﬁve seconds.

With the remote control

► To deadlock the vehicle, press this

button.

► Then press this button again within ﬁve

seconds after locking.

► Turn the key towards the front/rear to unlock/

lock the vehicle.

► Turn the key towards the rear again within

5 seconds to deadlock the vehicle.

38

Access

► Insert the built-in key into the latch (without

forcing it) and then turn the assembly.

► Remove the key and reﬁt the cap.

► Close the door(s) and check from the outside

that the vehicle is locked correctly.

If the vehicle is ﬁtted with an alarm, it will

not be activated when locking with the

Locking part of the vehicle (front

door/sliding side door/side-hinged

doors)

► If a sliding side door or side-hinged doors

are ﬁtted to your vehicle, check that the electric

child lock is not activated.

2

key.

If the alarm is activated, the siren sounds

when the door is opened; switch on the

ignition to stop it.

Unlocking of one part of the vehicle

(front passenger door/sliding side

door/side-hinged doors)

► Open the door.

► Use the interior opening control.

or

► With side-hinged doors, insert the built-in

key into the (left-hand) door lock, then turn it.

If the vehicle is unlocked with the key in

the lock after locking it with the remote

control or the Keyless Entry and Start

system, all doors and the boot are

unlocked.

If the vehicle is unlocked with the key in the

lock after locking it with the key, only the

doors (front door and sliding side door(s)) are

unlocked. The side-hinged doors and tailgate

are not unlocked. Switching on the ignition

unlocks them.

Front door

For more information on the Child lock

on a sliding side door or side-hinged

doors, refer to the corresponding section.

Unlocking the tailgate

Sliding side door

Central locking not

functioning

Use these procedures in the following cases:

– Central locking malfunction.

– Battery disconnected or discharged.

► From inside the vehicle, insert a small

screwdriver into hole A on the lock to unlock the

tailgate.

In the event of a malfunction of the

central locking system, the battery must

be disconnected to ensure that the vehicle is

locked fully.

Side-hinged doors

► Remove the cap located on the edge of the

door.

► Move the latch to the left.

39

Access

Battery type: CR2032/3 volts.

located in the corner, then clip the cover onto

the unit.

► Reinitialise the remote control.

For more information on Reinitialising the

remote control, refer to the corresponding

section.

Without Keyless Entry and Start

If the battery is discharged and your

vehicle is equipped with a tailgate and

an Extenso Cab, you will not be able to

access the loading area.

Replace the battery to regain access.

For more information on the 12 V battery,

refer to the corresponding section.

Do not throw remote control batteries

away, as they contain metals that are

harmful to the environment. Take them to an

approved disposal point.

In the event of a malfunction or if you

experience diﬃculty opening or closing

the tailgate, have it checked by a CITROËN

dealer or a qualiﬁed workshop without delay,

to avoid the issue deteriorating and prevent

any risk of the tailgate dropping, potentially

causing serious injury.

This equipment contains a button type

battery.

Do not swallow the battery. Risk of chemical

burns!

Swallowing the battery can cause serious

internal burning in only 2 hours and can be

fatal.

With Keyless Entry and Start

If batteries have been swallowed or inserted

into a part of the body, seek immediate

medical advice.

Keep new and used batteries out of the reach

of children.

Changing the battery

If the battery is ﬂat, this warning lamp

comes on, accompanied by an audible

signal and the display of a message.

If the battery compartment does not close

properly, stop using the product and keep it

out of the reach of children.

► Unclip the cover by inserting a small

screwdriver in the slot and lift the cover.

► Remove the ﬂat battery from its housing.

► Put the new battery in place, respecting the

polarity. Start by inserting it into the contacts

Risk of explosion if the battery is

replaced with an incorrect type!

Replace the battery with the same type.

40

Access

Risk of explosion or leaking of

inﬂammable liquid or gas!

Do not use in/store in/place in an environment

where the temperature is extremely high or

where the pressure is extremely low due to

very high altitude.

► Switch oﬀ the ignition and remove the key

from the ignition switch.

The remote control is now fully operational

again.

Central locking / unlocking

This function enables the doors to be locked or

unlocked simultaneously from inside the vehicle.

2

Do not try to burn, crush or cut a used battery.

Reinitialising the remote

control

Following replacement of the battery or in

the event of a fault, it may be necessary to

reinitialise the remote control.

When locking/deadlocking from the

outside

When the vehicle is locked or deadlocked

from the outside, the indicator lamp ﬂashes

and the button is deactivated.

► After normal locking, pull one of the

interior door controls to unlock the vehicle.

► After deadlocking, you must use the

remote control, the "Keyless Entry and

Start" system or the built-in key to unlock the

vehicle.

► Insert the mechanical key (incorporated into

the remote control) into the lock to open the

vehicle.

► Place the electronic key against the back-up

reader on the steering column and hold it there

until the ignition is switched on.

► With a manual gearbox, place the gear lever

in neutral then fully depress the clutch pedal.

► With an automatic gearbox, while in mode

P, depress the brake pedal.

Without Keyless Entry and Start

► Switch on the ignition by pressing the

"START/STOP" button.

Manual mode

If the fault persists after reinitialisation, contact a

CITROËN dealer or a qualiﬁed workshop without

delay.

► Press this button to lock / unlock the

vehicle.

► Switch the ignition oﬀ.

► Turn the key to position 2 (Ignition on).

► Immediately press the closed padlock button

for a few seconds.

Driving with the doors locked could make

it diﬃcult for the emergency services to

enter the vehicle in an emergency.

41

Access

If one of the doors is open, the central

locking from the inside does not function.

This is signalled by a mechanical noise from

the locks.

Driving with the doors locked could make

it more diﬃcult for the emergency

services to enter the vehicle in an emergency.

If the boot is open, only the locking of the

other doors is carried out. The indicator lamp

in the button remains oﬀ.

The indicator lamp goes oﬀ when

unlocking one or more doors of the

loading area.

With the ignition oﬀ and the vehicle fully

locked, the indicator lamp goes oﬀ for energy

economy reasons.

When locking from inside, the door

mirrors do not fold.

This button is unavailable if the vehicle

has been locked or deadlocked from

outside (using the key, remote control or

Keyless Entry and Start, depending on

equipment) or if any of the doors are still

open.

The indicator lamp also goes oﬀ when

unlocking one or more accesses.

Automatic mode

The loading area is always locked when driving.

To deactivate this automatic locking, go

to a CITROËN dealer or a qualiﬁed

workshop.

Automatic mode

This is the automatic central locking of the

vehicle when driving, also called anti-intrusion

security.

For more information on Anti-intrusion

security, refer to the corresponding section.

For more information on the Key, and, in

particular, on programming selective

locking for the loading area, refer to the

corresponding section.

Anti-intrusion security

This system allows automatic simultaneous

locking of the doors and boot as soon as the

speed of the vehicle exceeds 6 mph (10 km/h).

Manual mode

Locking/unlocking the

loading area

► With complete unlocking activated,

press this button to lock (indicator lamp

comes on)/unlock (indicator lamp goes oﬀ) the

vehicle.

► With selective unlocking activated, press this

button to lock (indicator lamp comes on)/unlock

(indicator lamp goes oﬀ) the loading area.

Operation

If one of the doors or the boot is open, the

automatic central locking does not take place.

This is signalled by the sound of the locks

rebounding, accompanied by illumination

of this warning lamp in the instrument panel, an

audible signal and the display of an alert

message.

42

Access

Opening to approximately 180°

Activation/Deactivation

Side-hinged doors

Keeping the left-hand door closed with the

right-hand door open

2

You can activate or deactivate this function

permanently.

► With the ignition on, press the central locking

button until an audible signal is triggered and

a corresponding message of conﬁrmation is

displayed.

The state of the system stays in the memory

when the ignition is switched oﬀ.

If ﬁtted to your vehicle, a check strap system

allows the doors to be opened from about 90° to

about 180°.

Driving with the doors locked may render

access by the emergency services to the

interior diﬃcult in an emergency.

► Pull the yellow control when the door is open.

The check strap will engage again automatically

on closing.

It is possible to drive with the right-hand

door open, to enable the transportation

of long loads.

The left-hand door is kept closed by the

distinctive "yellow" lock, positioned at the

base of the door.

This closed door must not be used to retain

loads.

Driving with the right-hand door open is a

special dispensation. Please comply with the

usual safety instructions on how to warn other

drivers.

Carrying long or voluminous objects

If you want to drive with the boot open,

you should press the central locking button

to lock the doors. Otherwise, every time the

speed of the vehicle exceeds 6 mph (10

km/h), the locks will rebound and the alerts

mentioned above will appear.

Pressing the central locking button unlocks

the vehicle.

Above 6 mph (10 km/h), this unlocking is

temporary.

General

recommendations for the

sliding side doors

Doors must only be operated when the

vehicle is stationary.

For your safety and that of your passengers,

as well as for correct operation of the doors,

you are strongly advised not to drive with a

door open.

Always check that it is safe to operate the

door and in particular, be sure not to leave

children or animals near the door controls

without supervision.

43

Access

The audible warning, the lighting of the "door

open" warning lamp and the message on the

screen are there to remind you. Contact a

CITROËN dealer or a qualiﬁed workshop if

you want to deactivate this warning.

Lock the vehicle when you use an automatic

car wash.

To hold the sliding side door in the open

position, open the door fully to engage

the latch (located at the bottom of the door).

On a steep slope

Doors and door clearances

Take care when opening doors while the vehicle

is on a slope facing uphill. The sloping terrain

could cause the door to open more quickly than

usual.

On a steep slope, manually guide the side door

to help it to close.

If the vehicle is on a slope facing downhill,

the door may not stay open, instead closing

suddenly, with a risk of injury. Always hold

the door to ensure that it does not close

unexpectedly.

Before opening or closing and while

moving doors, ensure that no person,

animal or object is in the door frame or any

other position that would block the desired

movement, inside or outside the vehicle.

If this advice is not followed, injuries or

damage may occur if any part of a person or

an object is trapped or caught.

When open, a door projects beyond the body.

Allow adequate clearance when parking

alongside walls, lamp-posts, high pavements,

etc.

Take care not to block the guide space

on the ﬂoor so that the door can slide

correctly.

For safety and functional reasons, do not

drive with the sliding side door open.

On a steep slope, the door's weight may

cause it to move, opening or closing

suddenly as a result.

Avoid leaving the vehicle unsupervised on a

steep slope with one or more doors open. If

this advice is not followed, injuries or damage

may occur if a person or an object is trapped

or caught.

To hold the sliding side door in the open

position, open the door fully to engage

the latch (located at the bottom of the door).

When open, a door never projects

beyond the rear bumper.

Rear roof ﬂap

44

Access

This roof ﬂap at the rear is compatible only with

side-hinged doors.

Support bar

The vehicle is equipped with a support bar for

transporting long loads, after opening the rear

roof ﬂap.

Alarm

2

► Fold back the support bar by lifting the lever.

► Guide it to the door pillar.

► Support the long loads to be transported, lift

them and reposition the support bar with one

hand.

► Ensure that it is secured correctly by

pressing the handle downwards past the point of

resistance and lash the load securely.

The side supports can be used as hooking

points.

System which protects and provides a deterrent

against theft and break-ins.

To open the rear roof ﬂap:

– Lift the black paddle of the toggle.

– Relax the toggle by pressing on the rear roof

ﬂap (downwards) then release the hook.

– Lift the rear roof ﬂap.

– Move past the point of resistance to lock the

rear roof ﬂap with the support props.

Self-protection function

The system checks for any malfunction

in its components.

The alarm is triggered if the battery, button or

siren wiring is disconnected or damaged.

For all work on the alarm system, contact a

CITROËN dealer or a qualiﬁed workshop.

The rear bumper has been reinforced to

serve as a step when entering the

vehicle.

Never drive without the props in place.

Never fasten a load to the roof ﬂap.

To close the rear roof ﬂap:

Exterior perimeter

– Check that the support bar is properly

secured.

– Lower the rear roof ﬂap.

Never drive without the support bar in

place.

The rear doors will only lock when the support

bar is installed.

When the roof ﬂap is open, take care when

driving where height is restricted.

Never rest loads directly on the rear doors.

Comply with the usual indications for warning

other drivers.

The system checks whether the vehicle is

opened.

– While pressing on the rear roof ﬂap

(downwards), take the two spring rings and then

place the hook in its housing.

– Lower the black paddle to lock the rear roof

ﬂap.

Locking the rear roof ﬂap holds it ﬁrmly against

the seal, ensuring watertight sealing with no

noise.

The alarm is triggered if anyone tries to open

one of the doors or the bonnet.

Volumetric

(without partition)

Only use the roof ﬂap on short trips.

45

Access

When the vehicle is parked, the alarm

will not be triggered if the vehicle is

knocked.

or

► Unlock the vehicle with the "Keyless Entry

and Start" system.

The monitoring system is deactivated: the

indicator lamp in the button goes oﬀ and the

direction indicators ﬂash for about 2 seconds.

The system checks for any variation in volume in

the passenger compartment.

The alarm is triggered if anyone breaks a

window, enters the passenger compartment or

moves inside the vehicle.

Locking the vehicle with full

alarm system

If the vehicle automatically locks itself

again (as happens if a door or the boot is

not opened within 30 seconds of unlocking),

the monitoring system is also reactivated

automatically.

Activation

► Switch oﬀ the ignition and exit the vehicle.

► Lock the vehicle using the remote control or

with the "Keyless Entry and Start" system.

The monitoring system is active: the red indicator

lamp in the button ﬂashes every second and

the direction indicators come on for about 2

seconds.

(with partition)

The system only checks for a variation in volume

inside the cab.

The alarm is triggered if anyone breaks a

window or enters the vehicle’s cab.

It will not be triggered if someone enters the

loading area.

Locking the vehicle

with exterior perimeter

monitoring only

Deactivate the interior volumetric and anti-tilt

monitoring to avoid the unwanted triggering of

the alarm, in certain cases such as:

– Slightly open window or sunroof.

– Washing the vehicle.

Following an instruction to lock the

vehicle, the exterior perimeter monitoring

is activated after 5 seconds and the interior

volumetric and anti-tilt monitoring after 45

seconds.

If your vehicle is ﬁtted with an Additional

heating/ventilation system, interior

volumetric monitoring is not compatible with it.

For more information on the Additional

heating/ventilation system, refer to the

corresponding section.

– Changing a wheel.

– Towing the vehicle.

– Transport on a ship or ferry.

If a door, the tailgate or the bonnet is not

closed properly, the vehicle is not locked

but the exterior perimeter monitoring will be

activated after 45 seconds at the same time

as the interior volumetric and anti-tilt

monitoring.

Deactivating the interior volumetric

and anti-tilt monitoring

► Switch oﬀ the ignition and within 10 seconds

press the alarm button until its red indicator lamp

is on ﬁxed.

Anti-tilt

The system checks for any change in the attitude

of the vehicle.

The alarm is triggered if the vehicle is lifted or

moved.

Deactivation

► Press the remote control unlocking button.

► Get out of the vehicle.

46

Access

remote control or unlock the vehicle using the

► Immediately lock the vehicle using the remote

control or the "Keyless Entry and Start" system.

Only the exterior perimeter monitoring is

activated; the button's red indicator lamp ﬂashes

once every second.

informs you that the alarm was triggered during

your absence. When the ignition is switched on,

this ﬂashing stops immediately.

2

"Keyless Entry and Start" system.

Electric windows

Failure of the remote control

To deactivate the monitoring functions:

► Unlock the vehicle using the key in the front

left-hand door lock.

► Open the door; the alarm is triggered.

► Switch on the ignition; this stops the alarm.

The indicator lamp in the button goes oﬀ.

To be taken into account, the deactivation

must be carried out every time the

ignition is switched oﬀ.

Type 1

Reactivating the interior volumetric

and anti-tilt monitoring

Locking the vehicle without

activating the alarm

► Lock or deadlock the vehicle using the key

(built-in the remote control) in the driver's door

lock.

► Deactivate the exterior perimeter monitoring

by unlocking the vehicle using the remote control

or the "Keyless Entry and Start" system.

The indicator lamp in the button goes oﬀ.

► Reactivate all monitoring by locking the

vehicle using the remote control or the "Keyless

Entry and Start" system.

1. Left-hand front.

2. Right-hand front.

Type 2

Malfunction

When the ignition is switched on, the ﬁxed

lighting of the red indicator lamp in the button

indicates a system malfunction.

Have it checked by a CITROËN dealer or a

qualiﬁed workshop.

The red indicator lamp in the button once again

ﬂashes every second.

Triggering of the alarm

This is indicated by sounding of the siren

and ﬂashing of the direction indicators for 30

seconds.

Depending on the country of sale, certain

monitoring functions remain active until the alarm

has been triggered eleven times consecutively.

When the vehicle is unlocked using the remote

control or the "Keyless Entry and Start" system,

rapid ﬂashing of the indicator lamp in the button

Automatic activation

(Depending on version)

The system is activated automatically 2 minutes

after the last door or the boot is closed.

► To avoid triggering the alarm on entering the

vehicle, ﬁrst press the unlocking button on the

47

Access

opens/closes completely when the switch is

released.

The lamp will remain lit until the controls are

reactivated.

Operating the switch again stops the movement

of the window.

The rear electric windows can still be controlled

using the driver's controls.

Window controls remain operational for

approximately 45 seconds after switching

oﬀ the ignition or after locking the vehicle.

After that time, the controls are disabled.

To reactivate them, switch on the ignition or

unlock the vehicle.

Reinitialising the electric

windows

After reconnecting the battery, or in the event

of abnormal window movement, the anti-pinch

function must be reinitialised.

The anti-pinch function is disabled during the

following sequence of operations.

For each window:

Anti-pinch

(Depending on version)

► Lower the window fully, then raise it; it will

rise in steps of a few centimetres each time the

control is pressed. Repeat the operation until the

window is fully closed.

► Continue to pull the control for at least one

second after the window reaches the closed

position.

If the window meets an obstacle while rising, it

stops and immediately partially lowers again.

1. Left-hand front

2. Right-hand front

3. Right-hand rear (depending on version)

4. Left-hand rear (depending on version)

5. Deactivation of electric window controls

located by rear seats (depending on version)

Deactivating the rear

controls for the rear electric

windows

(Type 2)

If an electric window meets an obstacle

during operation, the movement of the

window must be reversed. To do this, press

the relevant control.

When the driver operates the passengers’

electric window controls, it is important to

ensure that nothing can prevent the window

from closing properly.

It is important to ensure that passengers use

the electric windows correctly.

Pay particular attention to children when

operating the windows.

Manual operation

► To open/close the window, press/pull the

switch without passing the point of resistance;

the window stops as soon as the switch is

released.

For your children's safety, press control 5 to

deactivate the controls for the rear electric

windows, irrespective of their positions.

The red indicator lamp in the button comes

on and a conﬁrmation message is displayed.

Automatic operation

(Depending on version)

► To open/close the window, press/pull the

switch past its resistance point: the window

48

Access

Be aware of passengers and/or other persons

present when closing windows remotely using

the electronic key.

Do not put your head or arms through the

open windows when the vehicle is moving -

risk of serious injury!

2

Tilting rear door windows

Opening

► Turn the lever outwards.

► Push it fully to secure the window in the open

position.

Closing

► Pull the lever to release the window.

► Turn the lever fully inwards to secure the

window in the closed position.

49

Access for Your Citroen Berlingo SUV Third Generation (2018-2025)

Related Topics

Popular Owner Manuals

Latest Owner Manuals