Advertisement

Advertisement

Practical information -> Roof bars / Roof rack for Your Citroen Berlingo SUV Third Generation (2018-2025)

Practical information  
If the weight on board the vehicle is nearly up to  
the maximum authorised value, the indicator  
lamps of these buttons come on.  
Refer to national legislation in order to comply  
with the regulations for transporting objects  
that are longer than the vehicle.  
Roof bars / Roof rack  
7
Recommendations  
Distribute the load uniformly, taking care  
to avoid overloading one of the sides.  
Arrange the heaviest part of the load as close  
as possible to the roof.  
ON  
If the weight on board the vehicle exceeds  
the maximum authorised value, the indicator  
lamps of these buttons come on.  
In the event of loading a 7-seat model  
(not exceeding 40 cm in height) on the  
roof, do not exceed the following loads:  
– Three transverse bars bolted to the roof:  
100 kg.  
Secure the load firmly.  
Drive gently: the vehicle will be more  
susceptible to the effects of side winds and its  
stability may be affected.  
Regularly check the security and tight  
fastening of the roof bars and racks, at least  
before each trip.  
Display of the measurement on the  
instrument panel  
If the weight on board the vehicle  
exceeds the maximum authorised  
value, this indicator lamp comes on.  
– An aluminium rack: 70 kg.  
– A steel rack: 65 kg.  
Remove the roof bars once they are no longer  
needed.  
Malfunction  
Display of the malfunction in the loading  
area  
As a safety measure and to avoid  
damaging the roof, it is essential to use  
the roof bars and racks approved for your  
vehicle.  
Observe the instructions on fitting and use  
contained in the guide supplied with the roof  
bars and racks.  
In the event of loading (not exceeding  
40 cm in height) on the roof, do not  
exceed the following loads:  
– Transverse bars on longitudinal bars:  
80 kg.  
After the measurement is triggered from the  
loading area, the LEDs of the 3 buttons flash  
simultaneously for about 3 seconds and then go  
out.  
– Two transverse bars bolted to the roof:  
100 kg.  
Contact a CITROËN dealer or a qualified  
workshop.  
– Three transverse bars bolted to the roof:  
150 kg.  
– An aluminium rack: 120 kg.  
– A steel rack: 115 kg.  
Information displayed on the instrument  
panel  
If the height exceeds 40 cm, adapt the speed  
of the vehicle to the profile of the road to  
avoid damaging the roof bars or the roof rack  
and the fixings on the vehicle.  
These warning lamps come on, together with a  
message.  
Contact a CITROËN dealer or a qualified  
workshop.  
191  
Practical information  
To t the transverse roof bars or a roof rack, use  
the fixing points provided for this purpose:  
► Remove the fixing covers installed on the  
vehicle.  
with care (risk of burns), using the protected  
area.  
When the bonnet is open, take care not to  
damage the safety catch.  
► Put each fixing in place and lock them on the  
roof one by one.  
Do not open the bonnet under very windy  
conditions.  
► Ensure that the roof bars or the roof rack are  
correctly fitted (by shaking them).  
The bars are adaptable for each fixing point.  
Cooling of the engine when stopped  
The engine cooling fan may start after  
the engine has been switched off.  
Take care with objects or clothing that  
could be caught in the blades of the fan!  
Bonnet  
► Unclip the stay from its housing and place it  
in the support slot to hold the bonnet open.  
Stop & Start  
Before doing anything under the bonnet,  
you must switch off the ignition to avoid any  
risk of the engine restarting automatically.  
Take care with objects or clothing that could  
be caught in the blades of the cooling fan  
or in certain moving components - risk of  
strangulation and serious injury!  
Opening  
► Open the left-hand front door.  
Closing  
► Hold the bonnet and pull out the stay from the  
support slot.  
► Clip the stay in its housing.  
► Lower the bonnet and release it near the end  
of its travel.  
► Pull on the bonnet to check that it is locked  
correctly.  
Because of the presence of electrical  
equipment under the bonnet, it is  
recommended that exposure to water (rain,  
washing, etc.) be limited.  
The location of the interior bonnet  
release lever prevents the bonnet being  
opened when the left-hand front door is  
closed.  
► Pull the interior release lever, located at the  
bottom of the door frame, towards you.  
► Lift the exterior safety catch and raise the  
bonnet.  
Engine compartment  
The engine shown here is an example for  
illustrative purposes only.  
When the engine is hot, handle the  
exterior safety catch and the bonnet stay  
192