Get Ease of use and comfort -> Rear seats Guide for Citroen Spacetourer Van First Generation (2019-2024)

Ease of use and comfort

A. Longitudinal adjustment: lift the lever.

Front armrest

B. Tilt angle adjustment: pull the strap and

Height adjustment

push the seat back.

C. Folding the seat: give a firm upward pull

on the strap to unlock the seat.

D. Folding the seat from the back: pull the

strap then push the backrest forward.

Longitudinal adjustment

F Lower the armrest completely.

F Lift it again to the desired position (low,

intermediate or high).

F Once it is in the high position, lift it to unlock

it and bring it to the low position.

Second row seats

The 3 seats of the 2^ndrow are independent

and are the same width. Their backrests are

adjustable to adapt the boot load space.

F Lift lever A, at the front of the seat cushion

and adjust the seat as required.

62

Ease of use and comfort

Relax head restraints

"Comfort" position

Rear head restraints

3

The rear head restraints are removable and

have two positions:

Depending on the version, you can fold the

sides to obtain a better comfortable position.

F Pull strap B and push the seat back.

The backrest tilts and the cushion rotates

slightly.

-

high, the position for use,

low, the position for storage.

Never drive with the head restraints

removed; they must be fitted and correctly

adjusted.

To raise the head restraint, pull it upwards.

To lower it, press the lug A then push the head

restraint downwards.

Returning the seat to its initial

position

To remove it:

-

move the head restraint to the high position,

press the lug A while pulling the head

restraint upwards.

F Pull strap B and push the seat forward.

Flat floor

To replace it:

engage the head restraint rods in the

-

Do not allow children to operate the

seats unsupervised.

apertures, keeping the head restraint in line

with the seat backrest.

Each seat folds down to the floor to adapt the

boot volume as required.

Folding the seat

F Place the seats in the maximum rearwards

longitudinal position.

63

Ease of use and comfort

From outside the vehicle

You can fold the second row seat(s) directly

from the boot, after having first folded the third

row seats.

F Pull strap D to unlock the desired seat and

give the backrest a slight push forward. To

prevent any damage to the mechanism,

strap D will unclip if excessive force is

applied. It is just a matter of clipping it back

into place to make the system operational

again.

Before performing any operations on the

rear seats, to avoid damage to the seat

belts, make sure that the side belts are

properly tensioned. The central seat belt

must be put away. Secure the buckles

of the three seat belts to their anchoring

points.

Continuity panels

F Give a firm upward pull on strap C, as

shown by the arrow, to unlock the seat;

keep pulling the strap until the seat is

completely folded. Push the backrest

slightly forward so that the backrest tilts

and folds over the cushion. The seat and

cushion fold down to the floor.

Replacing the seat

Each seat has a continuity panel at the bottom

of the backrest, which, once unfolded:

From the boot, for example when loading

-

allows for a continuous loading surface in

the boot, whatever the position of the seats,

prevents objects from sliding beneath the

2nd row seats.

F If necessary, straighten the continuity

panels of the 2nd row of seats and lock

them.

F Raise the backrest and push it back until it

latches into place.

-

These continuity panels are not designed

to support a weight greater than 30 kg.

64

Ease of use and comfort

Unlocking/Locking the continuity panels

F Before unfolding the continuity panels,

check that the 2nd row seats are moved

back as far as possible.

Replacing the seat from

outside the vehicle, with

door open

Before moving the seats, make sure that

the trays behind the front row seats are

properly stowed.

F Slide the latch of the continuity panel

upwards to unlock it.

F Straighten out the continuity panel, then

slide the latch downwards to lock it.

If passengers are seated in the third row seats:

F Pull lever E. The seat unlocks and the

cushion comes up against the backrest.

F Keep lever E up by pushing it forwards. The

seat and cushion slide towards the front

seat.

This frees space behind the seat, allowing

the third row seat passengers to get into their

seats.

F manually push the seat and cushion back as

far as it can go; the seat does not return to

the maximum back position, leaving space

free for the third row passengers' legs,

F fold the cushion until it locks.

3

Make sure there is nothing on or under the

cushion of the seat you want to move.

Access to third row seats

Getting out of the vehicle

from third row seats

If this system fails (lever E), the third row

passengers can also get out after having

folded the backrest of the second row

seats using strap D.

Third row seats are accessed via the second

row lateral seats.

Do not let children operate the seats

unsupervised.

Third row seats

Concertina boards

The two rigid concertina boards, which are built

in to the vehicle, cover the two third row seats,

when these are in the folded away position.

F Lift lever E. The seat unlocks and the

cushion moves up to the backrest.

F Push the backrest holding lever E upwards.

65

Ease of use and comfort

Installing the seats

Seat storage

Each of the two boards can support

a maximum load of 100 kg.

Folding the concertina

boards

F Remove the load space cover.

For more information on the Interior

fittings and particularly on the load space

cover, refer to the corresponding section.

F Straighten the continuity panels of the

second row of seats and lock them in place.

F Fold the concertina board and straighten it

vertically.

F Pull strap F, located behind the backrest

of the seat. The backrest tilts backwards

bringing the cushion. The seat locks in the

open position.

F Straighten the continuity panels of the

second row of seats and lock them in place.

F Lower the head restraints.

F Correctly position the concertina board

vertically behind the seat.

F Make sure that the seat belts of the 3^rdrow

of seats are correctly fastened to the loops

and that they do not have any creases.

F Pull strap G, located at the bottom of the

backrest of the seat. The seat is unlocked.

F Then, push the backrest slightly forwards.

The backrest tilts and folds on the cushion.

The folded seat is arranged at the back of

its storage area provided for this purpose.

F Put the concertina boards back above the

folded down seats.

Pull the strap, the 3 parts of the board fold into

concertina form.

When the third row seats are straightened,

these folded concertina boards can be left:

-

either flat behind the seats,

or in the vertical position,

thus clearing the inside of the seat as a storage

space.

66

Ease of use and comfort -> Rear seats for Your Citroen Spacetourer Van First Generation (2019-2024)

Related Topics

Ease of use and comfort

Popular Owner Manuals

Latest Owner Manuals